Doped poly(vinylidene fluoride) as solid polymer electrolyte in nanocrystalline dye-sensitized solar cell

A new solid composite polymer electrolyte was reported by incorporating Azino-bis-(3-ethyl benzo thiazoline-6-sulphonate) ion [ABTS] as dopant in poly(vinylidene flouride) along with redox couple (1-/13-). Under certain conditions, the electrolyte composition forms brush like nano-rods while it is doped with Azino-bis-(3-ethly) benzo thiazoline-6-sulphonate) ion [ABTS], a pi-electron donor. The polymer electrolyte forms nanoscale interpenetrating network with the crystalline order of the polymer electrolyte that seems to be a desirable architecture for the active layer of the photoelectrochemical cell. With this new polymer electrolyte, dye-sensitized solar cell was fabricated using N3 dye absorbed over Ti02- nonoparticles (photoanode) and conducting carbon cement coated on the conducting press (FTO, photocathode). This polymer composite has been successfully used as a promising candidate as solid polymer electrolyte in nanocrystalline dye-sensitized solar cell.

The creative sector in New Zealand : mapping and economic role : report to New Zealand Trade and Enterprise

The New Zealand creative sector was responsible for almost 121,000 jobs at the time of the 2006 Census (6.3% of total employment). These are divided between • 35,751 creative specialists – persons employed doing creative work in creative industries • 42,300 support workers - persons providing management and support services in creative industries • 42,792 embedded creative workers – persons engaged in creative work in other types of enterprise The most striking feature of this breakdown is the fact that the largest group of creative workers are employed outside the creative industries, i.e. in other types of businesses. Even within the creative industries, there are fewer people directly engaged in creative work than in providing management and support. Creative sector employees earned incomes of approximately $52,000 per annum at the time of the 2006 Census. This is relatively uniform across all three types of creative worker, and is significantly above the average for all employed persons (of approximately $40,700). Creative employment and incomes were growing strongly over both five year periods between the 1996, 2001 and 2006 Censuses. However, when we compare creative and general trends, we see two distinct phases in the development of the creative sector: • rapid structural growth over the five years to 2001 (especially led by developments in ICT), with creative employment and incomes increasing rapidly at a time when they were growing modestly across the whole economy; • subsequent consolidation, with growth driven by more by national economic expansion than structural change, and creative employment and incomes moving in parallel with strong economy-wide growth. Other important trends revealed by the data are that • the strongest growth during the decade was in embedded creative workers, especially over the first five years. The weakest growth was in creative specialists, with support workers in creative industries in the middle rank, • by far the strongest growth in creative industries’ employment was in Software & digital content, which trebled in size over the decade Comparing New Zealand with the United Kingdom and Australia, the two southern hemisphere nations have significantly lower proportions of total employment in the creative sector (both in creative industries and embedded employment). New Zealand’s and Australia’s creative shares in 2001 were similar (5.4% each), but in the following five years, our share has expanded (to 5.7%) whereas Australia’s fell slightly (to 5.2%) – in both cases, through changes in creative industries’ employment. The creative industries generated $10.5 billion in total gross output in the March 2006 year. Resulting from this was value added totalling $5.1b, representing 3.3% of New Zealand’s total GDP. Overall, value added in the creative industries represents 49% of industry gross output, which is higher than the average across the whole economy, 45%. This is a reflection of the relatively high labour intensity and high earnings of the creative industries. Industries which have an above-average ratio of value added to gross output are usually labour-intensive, especially when wages and salaries are above average. This is true for Software & Digital Content and Architecture, Design & Visual Arts, with ratios of 60.4% and 55.2% respectively. However there is significant variation in this ratio between different parts of the creative industries, with some parts (e.g. Software & Digital Content and Architecture, Design & Visual Arts) generating even higher value added relative to output, and others (e.g. TV & Radio, Publishing and Music & Performing Arts) less, because of high capital intensity and import content. When we take into account the impact of the creative industries’ demand for goods and services from its suppliers and consumption spending from incomes earned, we estimate that there is an addition to economic activity of: • $30.9 billion in gross output, $41.4b in total • $15.1b in value added, $20.3b in total • 158,100 people employed, 234,600 in total The total economic impact of the creative industries is approximately four times their direct output and value added, and three times their direct employment. Their effect on output and value added is roughly in line with the average over all industries, although the effect on employment is significantly lower. This is because of the relatively high labour intensity (and high earnings) of the creative industries, which generate below-average demand from suppliers, but normal levels of demand though expenditure from incomes. Drawing on these numbers and conclusions, we suggest some (slightly speculative) directions for future research. The goal is to better understand the contribution the creative sector makes to productivity growth; in particular, the distinctive contributions from creative firms and embedded creative workers. The ideas for future research can be organised into the several categories: • Understanding the categories of the creative sector– who is doing the business? In other words, examine via more fine grained research (at a firm level perhaps) just what is the creative contribution from the different aspects of the creative sector industries. It may be possible to categorise these in terms of more or less striking innovations. • Investigate the relationship between the characteristics and the performance of the various creative industries/ sectors; • Look more closely at innovation at an industry level e.g. using an index of relative growth of exports, and see if this can be related to intensity of use of creative inputs; • Undertake case studies of the creative sector; • Undertake case studies of the embedded contribution to growth in the firms and industries that employ them, by examining taking several high performing noncreative industries (in the same way as proposed for the creative sector). • Look at the aggregates – drawing on the broad picture of the extent of the numbers of creative workers embedded within the different industries, consider the extent to which these might explain aspects of the industries’ varied performance in terms of exports, growth and so on. • This might be able to extended to examine issues like the type of creative workers that are most effective when embedded, or test the hypothesis that each industry has its own particular requirements for embedded creative workers that overwhelms any generic contributions from say design, or IT.

The use of high dynamic range luminance mapping in the assessment, understanding and defining of visual issues in post occupancy building assessment

The international focus on embracing daylighting for energy efficient lighting purposes and the corporate sector’s indulgence in the perception of workplace and work practice “transparency” has spurned an increase in highly glazed commercial buildings. This in turn has renewed issues of visual comfort and daylight-derived glare for occupants. In order to ascertain evidence, or predict risk, of these events; appraisals of these complex visual environments require detailed information on the luminances present in an occupant’s field of view. Conventional luminance meters are an expensive and time consuming method of achieving these results. To create a luminance map of an occupant’s visual field using such a meter requires too many individual measurements to be a practical measurement technique. The application of digital cameras as luminance measurement devices has solved this problem. With high dynamic range imaging, a single digital image can be created to provide luminances on a pixel-by-pixel level within the broad field of view afforded by a fish-eye lens: virtually replicating an occupant’s visual field and providing rapid yet detailed luminance information for the entire scene. With proper calibration, relatively inexpensive digital cameras can be successfully applied to the task of luminance measurements, placing them in the realm of tools that any lighting professional should own. This paper discusses how a digital camera can become a luminance measurement device and then presents an analysis of results obtained from post occupancy measurements from building assessments conducted by the Mobile Architecture Built Environment Laboratory (MABEL) project. This discussion leads to the important realisation that the placement of such tools in the hands of lighting professionals internationally will provide new opportunities for the lighting community in terms of research on critical issues in lighting such as daylight glare and visual quality and comfort.

Multi-objective mission flight planning in civil unmanned aerial systems

Unmanned Aerial Vehicles (UAVs) are emerging as an ideal platform for a wide range of civil applications such as disaster monitoring, atmospheric observation and outback delivery. However, the operation of UAVs is currently restricted to specially segregated regions of airspace outside of the National Airspace System (NAS). Mission Flight Planning (MFP) is an integral part of UAV operation that addresses some of the requirements (such as safety and the rules of the air) of integrating UAVs in the NAS. Automated MFP is a key enabler for a number of UAV operating scenarios as it aids in increasing the level of onboard autonomy. For example, onboard MFP is required to ensure continued conformance with the NAS integration requirements when there is an outage in the communications link. MFP is a motion planning task concerned with finding a path between a designated start waypoint and goal waypoint. This path is described with a sequence of 4 Dimensional (4D) waypoints (three spatial and one time dimension) or equivalently with a sequence of trajectory segments (or tracks). It is necessary to consider the time dimension as the UAV operates in a dynamic environment. Existing methods for generic motion planning, UAV motion planning and general vehicle motion planning cannot adequately address the requirements of MFP. The flight plan needs to optimise for multiple decision objectives including mission safety objectives, the rules of the air and mission efficiency objectives. Online (in-flight) replanning capability is needed as the UAV operates in a large, dynamic and uncertain outdoor environment. This thesis derives a multi-objective 4D search algorithm entitled Multi- Step A* (MSA*) based on the seminal A* search algorithm. MSA* is proven to find the optimal (least cost) path given a variable successor operator (which enables arbitrary track angle and track velocity resolution). Furthermore, it is shown to be of comparable complexity to multi-objective, vector neighbourhood based A* (Vector A*, an extension of A*). A variable successor operator enables the imposition of a multi-resolution lattice structure on the search space (which results in fewer search nodes). Unlike cell decomposition based methods, soundness is guaranteed with multi-resolution MSA*. MSA* is demonstrated through Monte Carlo simulations to be computationally efficient. It is shown that multi-resolution, lattice based MSA* finds paths of equivalent cost (less than 0.5% difference) to Vector A* (the benchmark) in a third of the computation time (on average). This is the first contribution of the research. The second contribution is the discovery of the additive consistency property for planning with multiple decision objectives. Additive consistency ensures that the planner is not biased (which results in a suboptimal path) by ensuring that the cost of traversing a track using one step equals that of traversing the same track using multiple steps. MSA* mitigates uncertainty through online replanning, Multi-Criteria Decision Making (MCDM) and tolerance. Each trajectory segment is modeled with a cell sequence that completely encloses the trajectory segment. The tolerance, measured as the minimum distance between the track and cell boundaries, is the third major contribution. Even though MSA* is demonstrated for UAV MFP, it is extensible to other 4D vehicle motion planning applications. Finally, the research proposes a self-scheduling replanning architecture for MFP. This architecture replicates the decision strategies of human experts to meet the time constraints of online replanning. Based on a feedback loop, the proposed architecture switches between fast, near-optimal planning and optimal planning to minimise the need for hold manoeuvres. The derived MFP framework is original and shown, through extensive verification and validation, to satisfy the requirements of UAV MFP. As MFP is an enabling factor for operation of UAVs in the NAS, the presented work is both original and significant.

Professional education in built environment and design

Early and rich conversations with a range of stakeholders – academics, professionals and graduates in their early years of practice – quickly clarified that the singular challenge for most parties centres on the ways in which courses prepare graduates for the pace, diversity and flux of contemporary professional practice.---------In pursuing understanding of this central challenge this study has focused on new graduates in BED disciplines by canvassing their views and those of two other major stakeholder groups (academic staff and professional practitioners in the disciplines studied). The first crucial years of a young graduate’s life in the workforce are shaped by a number of factors including the quality of the transition-to-work experience. The quality of this life-shaping transition is dependent on a range of factors including the ways in which graduates are educated in universities, their personal developmental characteristics and those of the professional people around them and the preparedness of workplaces and other professional groups to guide new recruits through the transition experience. This study makes recommendations about how the variations in transition experience, resulting from the vagaries of all these factors across a range of worksites, may be better understood, perhaps normalised, and, at least, supported. . Early and rich conversations with a range of stakeholders – academics, professionals and graduates in their early years of practice – quickly clarified that the singular challenge for most parties centres on the ways in which courses prepare graduates for the pace, diversity and flux of contemporary professional practice. The study proceeded through literature review, focus group interviews, national online survey and workshops. Through all these methods a number of challenges and factors essential to the transition experience, and the quality of education which precedes it, were identified. Firstly the study found further evidence of the importance of higher-order graduate capabilities, namely, the development of judgment, critical enquiry and strategic thinking. Alongside these capabilities the importance of the development of emotional intelligence, particularly interpersonal and social skills, was stressed by all stakeholders. At the time of writing the global economic crisis was providing challenges to the sector and its young graduates. This phenomenon proved the value of the development of resilience and persistence in graduates, the education system was called upon by all stakeholders as a place where the future-proofing of neophytes would ensure that the unknown challenges of the future could also be confronted. The study found that the challenges of transition to work are best supported by authentic undergraduate experiences both on and off campus, inside and outside classrooms, and that commencing professional life is made easier for new graduates when university courses and workplace settings develop, sustain and support high standards and high expectations of students. All these findings indicate the importance of stakeholder expectations, roles and responsibilities in respect of the transition-to-work experience. Whilst full agreement about how these things should occur is not necessary, a process (amongst stakeholders) which seeks value alignment around transition through discussion, debate and agenda-setting would probably assist to address what is seen as a major challenge in built environment and design education.

ePortfolio use by university students in Australia : Developing a sustainable community of practice

This report documents Stage Two of the Australian ePortfolio Project (AeP2), to specifically explore the current scope of national and international ePortfolio communities of practice in order to identify the factors that have contributed to their success and sustainability. The study has built on Stage One of the Australian ePortfolio Project (Hallam, Harper, McCowan, Hauville, McAllister, & Creagh, 2008), which outlined the broad range of issues and challenges, as well as significant opportunities, that faced the higher education sector in terms of ePortfolio practice, to determine how the emergent community of ePortfolio researchers and practitioners in Australia might be advanced. ---------- The overarching aims of this project were to focus on building the Australian community of practice through an online forum and further symposium activities. Through the research activities the project sought to generate the following major outcomes: develop a forum within the ALTC Exchange to support an ePortfolio community of practice; develop strategies to encourage interest in and engagement with community of practice activities; develop and promote resources to support the diverse stakeholders in ePortfolio practice; collaborate in the establishment of a cross-sector ePortfolio community of practice; host a second Australian ePortfolio Symposium (AeP2) to disseminate the findings from the Australian ePortfolio Project, to explore innovative practice in ePortfolio use in higher education, to articulate policy developments, and to stimulate discussion on international ePortfolio issues; host an associated trade display as a forum for strengthening the higher education sector’s understanding of the features and functionality of ePortfolio platforms; develop resources to support an ePortfolio symposium model that may be adopted for future events. ----------- The project activities encompassed a survey of stakeholders, a program of semi-structured interviews with community managers and a series of case studies depicting successful ePortfolio communities. The survey of ePortfolio practitioners sought to determine the potential value of an ePortfolio CoP, the preferred focus for and the desired features of such a community, as well as the options for the technical and social architecture of an online forum. Through the semi-structured interviews it was possible to examine current examples of CoP activity, to identify the critical success factors and the challenges faced by individual ePortfolio CoPs, so that the attributes of good practice could be presented. The data collected in the interviews contributed to the development of 14 case studies, which have been beneficial in illustrating the diverse nature of CoPs in Australia and overseas.----------- The report presents a rich picture of national and international ePortfolio communities of practice, with an examination of the factors that have contributed to their success and sustainability.

Investigation of MEMS inertial sensors and aircraft dynamic models in global positioning system integrity monitoring for approaches with vertical guidance

An Approach with Vertical Guidance (APV) is an instrument approach procedure which provides horizontal and vertical guidance to a pilot on approach to landing in reduced visibility conditions. APV approaches can greatly reduce the safety risk to general aviation by improving the pilot’s situational awareness. In particular the incidence of Controlled Flight Into Terrain (CFIT) which has occurred in a number of fatal air crashes in general aviation over the past decade in Australia, can be reduced. APV approaches can also improve general aviation operations. If implemented at Australian airports, APV approach procedures are expected to bring a cost saving of millions of dollars to the economy due to fewer missed approaches, diversions and an increased safety benefit. The provision of accurate horizontal and vertical guidance is achievable using the Global Positioning System (GPS). Because aviation is a safety of life application, an aviation-certified GPS receiver must have integrity monitoring or augmentation to ensure that its navigation solution can be trusted. However, the difficulty with the current GPS satellite constellation alone meeting APV integrity requirements, the susceptibility of GPS to jamming or interference and the potential shortcomings of proposed augmentation solutions for Australia such as the Ground-based Regional Augmentation System (GRAS) justifies the investigation of Aircraft Based Augmentation Systems (ABAS) as an alternative integrity solution for general aviation. ABAS augments GPS with other sensors at the aircraft to help it meet the integrity requirements. Typical ABAS designs assume high quality inertial sensors to provide an accurate reference trajectory for Kalman filters. Unfortunately high-quality inertial sensors are too expensive for general aviation. In contrast to these approaches the purpose of this research is to investigate fusing GPS with lower-cost Micro-Electro-Mechanical System (MEMS) Inertial Measurement Units (IMU) and a mathematical model of aircraft dynamics, referred to as an Aircraft Dynamic Model (ADM) in this thesis. Using a model of aircraft dynamics in navigation systems has been studied before in the available literature and shown to be useful particularly for aiding inertial coasting or attitude determination. In contrast to these applications, this thesis investigates its use in ABAS. This thesis presents an ABAS architecture concept which makes use of a MEMS IMU and ADM, named the General Aviation GPS Integrity System (GAGIS) for convenience. GAGIS includes a GPS, MEMS IMU, ADM, a bank of Extended Kalman Filters (EKF) and uses the Normalized Solution Separation (NSS) method for fault detection. The GPS, IMU and ADM information is fused together in a tightly-coupled configuration, with frequent GPS updates applied to correct the IMU and ADM. The use of both IMU and ADM allows for a number of different possible configurations. Three are investigated in this thesis; a GPS-IMU EKF, a GPS-ADM EKF and a GPS-IMU-ADM EKF. The integrity monitoring performance of the GPS-IMU EKF, GPS-ADM EKF and GPS-IMU-ADM EKF architectures are compared against each other and against a stand-alone GPS architecture in a series of computer simulation tests of an APV approach. Typical GPS, IMU, ADM and environmental errors are simulated. The simulation results show the GPS integrity monitoring performance achievable by augmenting GPS with an ADM and low-cost IMU for a general aviation aircraft on an APV approach. A contribution to research is made in determining whether a low-cost IMU or ADM can provide improved integrity monitoring performance over stand-alone GPS. It is found that a reduction of approximately 50% in protection levels is possible using the GPS-IMU EKF or GPS-ADM EKF as well as faster detection of a slowly growing ramp fault on a GPS pseudorange measurement. A second contribution is made in determining how augmenting GPS with an ADM compares to using a low-cost IMU. By comparing the results for the GPS-ADM EKF against the GPS-IMU EKF it is found that protection levels for the GPS-ADM EKF were only approximately 2% higher. This indicates that the GPS-ADM EKF may potentially replace the GPS-IMU EKF for integrity monitoring should the IMU ever fail. In this way the ADM may contribute to the navigation system robustness and redundancy. To investigate this further, a third contribution is made in determining whether or not the ADM can function as an IMU replacement to improve navigation system redundancy by investigating the case of three IMU accelerometers failing. It is found that the failed IMU measurements may be supplemented by the ADM and adequate integrity monitoring performance achieved. Besides treating the IMU and ADM separately as in the GPS-IMU EKF and GPS-ADM EKF, a fourth contribution is made in investigating the possibility of fusing the IMU and ADM information together to achieve greater performance than either alone. This is investigated using the GPS-IMU-ADM EKF. It is found that the GPS-IMU-ADM EKF can achieve protection levels approximately 3% lower in the horizontal and 6% lower in the vertical than a GPS-IMU EKF. However this small improvement may not justify the complexity of fusing the IMU with an ADM in practical systems. Affordable ABAS in general aviation may enhance existing GPS-only fault detection solutions or help overcome any outages in augmentation systems such as the Ground-based Regional Augmentation System (GRAS). Countries such as Australia which currently do not have an augmentation solution for general aviation could especially benefit from the economic savings and safety benefits of satellite navigation-based APV approaches.

Bushfire responsive architecture : strategies for reconciling bushfire and biodiversity with daily life

My perspective on the problems associated with building in bushfire prone landscapes comes from 12 years of study of the biophysical and cultural landscapes in the Great Southern Region of WA which resulted in the design and construction of the ‘Hhouse’ at Bremer Bay. The house was developed using a ‘ground up’ approach whereby I conducted a topographical survey and worked with a local botanist and a bushfire risk consultant to ascertain the level of threat that fire presented to this particular site. My intention from the outset however, was not to design a bushfire resistant house per se, but to develop a design which would place the owners in close proximity to the highly biodiverse heath vegetation of the site. I was also seeking a means—through architectural design—of linking the patterns of usage of the house with other site specific conditions related to the prevailing winds, solar orientation and seasonal change.

Housing supply in Australia : the impact of the availability of development finance

Before the Global Financial Crisis many providers of finance had growth mandates and actively pursued development finance deals as a way of gaining higher returns on funds with regular capital turnover and re-investment possible. This was able to be achieved through high gearing and low presales in a strong market. As asset prices fell, loan covenants breached and memories of the 1990’s returned, banks rapidly adjusted their risk appetite via retraction of gearing and expansion of presale requirements. Early signs of loosening in bank credit policy are emerging, however parties seeking development finance are faced with a severely reduced number of institutions from which to source funding. The few institutions that are lending are filtering out only the best credit risks by way of constrictive credit conditions including: low loan to value ratios, the corresponding requirement to contribute high levels of equity, lack of support in non-prime locations and the requirement for only borrowers with well established track records. In this risk averse and capital constrained environment, the ability of developers to proceed with real estate developments is still being constrained by their inability to obtain project finance. This paper will examine the pre and post GFC development finance environment. It will identify the key lending criteria relevant to real estate development finance and will detail the related changes to credit policies over this period. The associated impact to real estate development projects will be presented, highlighting the significant constraint to supply that the inability to obtain finance poses.

The modern movement architecture of four South African cities

South Africa's modern architecture is not confined to the cities, but the ideas of the movement were mostly disseminated by architects and academics in Johannesburg, Pretoria, Durban and Cape Town, its four major urban centres. The lay out of significant areas of each city was also influenced by international modernist plans. In outlining the achievements and innovative designs of architects in these cities between the 1930s and 1970s, this article draws a picture of the importance of modernism in South African urban space, and of its diversity. It also draws attention to the political nature of the South African landscape and space, where modernist design was used for racial purposes, and to past and present conservation ideologies. The second part of the article concerns the conservation of modern buildings in these centres; it quotes bibliographies and lists the registers, those existing or under construction. It concludes with an overview of the conservation legislation in place and the challenges of conservation in a context of changing cultural values.

Water sensitive urban design : landscape planning and design to improve water quality in Shijiazhaung and Yueyang

Water quality issues are heavily dependent on land development and management decisions within river and lake catchments or watersheds. Economic benefits of urbanisation may be short‐ lived without cleaner environmental outcomes. However, whole‐of‐catchment thinking is not, as yet, as frequent a consideration in urban planning and development in China as it is in many other countries. Water is predominantly seen as a resource to be ‘owned’ by different jurisdictions and allocated to numerous users, both within a catchment and between catchments. An alternative to this approach is to think of water in the same way as other commodities that must be kept moving through a complex transport system. Water must ultimately arrive at particular destinations in the biosphere, although it travels across a broad landscape and may be held up temporarily at certain places along the way. While water extraction can be heavily controlled, water pollution is far more difficult to regulate. Both have significant impacts on water availability and flows both now and in the future. As Chinese cities strive to improve economic conditions for their citizens, new centres are being rebuilt and environmental valued

Rhetoric of landscape architecture and interior design discourses : preparation for cross-disciplinary practice

The rhetoric of the pedagogic discourses of landscape architectural students and interior design students is described as part of a doctoral study undertaken to document practices and orientations prior to cross-disciplinary collaboration. We draw on the theoretical framework of Basil Bernstein, an educational sociologist, and the rhetorical method of Kenneth Burke, a literary dramatist, to study the grammars of ‘landscape’ representation employed within these disciplinary examples. We investigate how prepared final year students are for working in a cross-disciplinary manner. The discursive interactions of their work, as illustrated by four examples of drawn images and written text, are described. Our findings suggest that we need to concern ourselves aspects of our pedagogic discourse that brings uniqueness and value to our disciplines ,as well as that shared discourses between disciplines.

Curtains and carnality : processural seductions in eighteenth century text and space

Libertine erotic novellas included a number of seductive descriptions of unfolding spaces often seen through the eyes of a narrator. Instructional volumes such as Point de lendermain by Vivant Denon (1777) aimed at the sexual education of young women and the titillation of men also followed suit. Similarly architectural theory such as Le Camus de Mézières’, The Genius of Architecture (1780) also promoted the sensuous and seductive aspects of surfaces and spatial arrangements. In the erotic settings of the cabinet, descriptions of curtains generate as much arousal as the outline of a naked body, and for some players it is the space that is desired above their lover.