Using 3D surface datasets to understand landslide evolution: From analogue models to real case study

Early detection of landslide surface deformation with 3D remote sensing techniques, as TLS, has become a great challenge during last decade. To improve our understanding of landslide deformation, a series of analogue simulation have been carried out on non-rigid bodies coupled with 3D digitizer. All these experiments have been carried out under controlled conditions, as water level and slope angle inclination. We were able to follow 3D surface deformation suffered by complex landslide bodies from precursory deformation still larger failures. These experiments were the basis for the development of a new algorithm for the quantification of surface deformation using automatic tracking method on discrete points of the slope surface. To validate the algorithm, comparisons were made between manually obtained results and algorithm surface displacement results. Outputs will help in understanding 3D deformation during pre-failure stages and failure mechanisms, which are fundamental aspects for future implementation of 3D remote sensing techniques in early warning systems.

Devolatilization-induced pressure build-up: Implications for reaction front movement and breccia pipe formation

Generation of fluids during metamorphism can significantly influence the fluid overpressure, and thus the fluid flow in metamorphic terrains. There is currently a large focus on developing numerical reactive transport models, and with it follows the need for analytical solutions to ensure correct numerical implementation. In this study, we derive both analytical and numerical solutions to reaction-induced fluid overpressure, coupled to temperature and fluid flow out of the reacting front. All equations are derived from basic principles of conservation of mass, energy and momentum. We focus on contact metamorphism, where devolatilization reactions are particularly important owing to high thermal fluxes allowing large volumes of fluids to be rapidly generated. The analytical solutions reveal three key factors involved in the pressure build-up: (i) The efficiency of the devolatilizing reaction front (pressure build-up) relative to fluid flow (pressure relaxation), (ii) the reaction temperature relative to the available heat in the system and (iii) the feedback of overpressure on the reaction temperature as a function of the Clapeyron slope. Finally, we apply the model to two geological case scenarios. In the first case, we investigate the influence of fluid overpressure on the movement of the reaction front and show that it can slow down significantly and may even be terminated owing to increased effective reaction temperature. In the second case, the model is applied to constrain the conditions for fracturing and inferred breccia pipe formation in organic-rich shales owing to methane generation in the contact aureole.

Latest Miocene - Pliocene Larger Foraminifera and depositional environments of the carbonate bank of La Désirade Island, Guadeloupe (French Antilles)

In this paper we present first results of the study of planktonic Foraminifera, large benthic Foraminifera and carbonate facies of La Désirade, aiming at a definition of the age and depositional environments of the Neogene carbonates of this island. The study of planktonic Foraminifera from the Detrital Offshore Limestones (DOL) of the Anciènne Carrière allows to constrain the biochronology of this formation to the lower Zone N19 and indicates a latest Miocene to early Pliocene (5.48 - 4.52 Ma) age. Large benthic Foraminifera were studied both as isolated and often naturally split specimens from the DOL, and in thin sections of limestones from the DOL and the Limestone Table (LT). The assemblages of Foraminifera include Nummulitidae, Amphisteginidae, Asterigerinidae, Peneroplidae, Soritidae, Rotalidae (Globigerinidae: Globigerinoides, Sphaeroidenellopsis, Orbulina) and incrusting Foraminifera (Homotrema and Sporadotrema). The genera Amphistegina, Archaias and Operculina are discussed. Concerning the Nummulitidae we include both "Paraspiroclypeus" chawneri and "Nummulites" cojimarensis, as well as a newly described species, Operculina desiradensis new species, in the genus Operculina, because the differences between these 3 species are rather on the specific than the generic level, while their morphology, studied by SEM, is compatible with the definition of the genus Operculina (D'Orbigny1826, emend. Hottinger 1977). The three species can be easily distinguished on the basis of their differences in spiral growth: while O. desiradensis has an overall logarithmic spiral growth, O. cojimarensis and especially O. chawneri show a tighter and more geometric spiral growth. O. cojimarensis and O. chawneri were originally described from Cuba in outcrops originally dated as Oligocene and later redated as early Pliocene. Therefore, O. chawneri was considered until now as restricted to the early Pliocene. However, in the absence of a detailed morphometric and biostratigraphic study of the Caribbean Neogene nummulitids, it is difficult to evaluate the biochronologic range of these species.The history of the carbonates begins with the initial tectonic uplift and erosion of the Jurassic igneous basement of La Désirade, that must have occurred at latest in late Miocene times, when sea-level oscillated around a long term stable mean. The rhythmic deposition of the Désirade Limestone Table (LT) can be explained by synsedimentary subsidence in a context of rapidly oscillating sea-level due to precession-driven (19-21 kyr) glacio-eustatic sea-level changes during the latest Miocene- Pliocene. Except for a thin reef cap present at the eastern edge of the LT, no other in-place reefal constructions have been observed in the LT. The DOL of western Désirade are interpreted as below wave base gravity deposits that accumulated beneath a steep fore-reef slope. They document the mobilisation of carbonate material (including Larger Foraminifera) from an adjacent carbonate platform by storms and their gravitational emplacement as debris and grain flows. The provenance of both the reefal carbonate debris and the tuffaceous components redeposited in the carbonates of La Désirade must be to the west, i. e. the carbonate platforms of Marie Galante and Grande Terre.

Monitoring switch-type sensors and powering autonomous sensors via inductive coupling: application to removable seats in vehicles

Aquesta tesi explora la possibilitat de fer servir enllaços inductius per a una aplicació de l’automòbil on el cablejat entre la centraleta (ECU) i els sensors o detectors és difícil o impossible. S’han proposat dos mètodes: 1) el monitoratge de sensors commutats (dos possibles estats) via acoblament inductiu i 2) la transmissió mitjançant el mateix principi físic de la potència necessària per alimentar els sensors autònoms remots. La detecció d'ocupació i del cinturó de seguretat per a seients desmuntables pot ser implementada amb sistemes sense fils passius basats en circuits ressonants de tipus LC on l'estat dels sensors determina el valor del condensador i, per tant, la freqüència de ressonància. Els canvis en la freqüència són detectats per una bobina situada en el terra del vehicle. S’ha conseguit provar el sistema en un marge entre 0.5 cm i 3 cm. Els experiments s’han dut a terme fent servir un analitzador d’impedàncies connectat a una bobina primària i sensors comercials connectats a un circuit remot. La segona proposta consisteix en transmetre remotament la potència des d’una bobina situada en el terra del vehicle cap a un dispositiu autònom situat en el seient. Aquest dispositiu monitorarà l'estat dels detectors (d'ocupació i de cinturó) i transmetrà les dades mitjançant un transceptor comercial de radiofreqüència o pel mateix enllaç inductiu. S’han avaluat les bobines necessàries per a una freqüència de treball inferior a 150 kHz i s’ha estudiat quin és el regulador de tensió més apropiat per tal d’aconseguir una eficiència global màxima. Quatre tipus de reguladors de tensió s’han analitzat i comparat des del punt de vista de l’eficiència de potència. Els reguladors de tensió de tipus lineal shunt proporcionen una eficiència de potència millor que les altres alternatives, els lineals sèrie i els commutats buck o boost. Les eficiències aconseguides han estat al voltant del 40%, 25% i 10% per les bobines a distàncies 1cm, 1.5cm, i 2cm. Les proves experimentals han mostrat que els sensors autònoms han estat correctament alimentats fins a distàncies de 2.5cm.

Discovery of catalases in members of the Chlamydiales order.

Catalase is an important virulence factor for survival in macrophages and other phagocytic cells. In Chlamydiaceae, no catalase had been described so far. With the sequencing and annotation of the full genomes of Chlamydia-related bacteria, the presence of different catalase-encoding genes has been documented. However, their distribution in the Chlamydiales order and the functionality of these catalases remain unknown. Phylogeny of chlamydial catalases was inferred using MrBayes, maximum likelihood, and maximum parsimony algorithms, allowing the description of three clade 3 and two clade 2 catalases. Only monofunctional catalases were found (no catalase-peroxidase or Mn-catalase). All presented a conserved catalytic domain and tertiary structure. Enzymatic activity of cloned chlamydial catalases was assessed by measuring hydrogen peroxide degradation. The catalases are enzymatically active with different efficiencies. The catalase of Parachlamydia acanthamoebae is the least efficient of all (its catalytic activity was 2 logs lower than that of Pseudomonas aeruginosa). Based on the phylogenetic analysis, we hypothesize that an ancestral class 2 catalase probably was present in the common ancestor of all current Chlamydiales but was retained only in Criblamydia sequanensis and Neochlamydia hartmannellae. The catalases of class 3, present in Estrella lausannensis and Parachlamydia acanthamoebae, probably were acquired by lateral gene transfer from Rhizobiales, whereas for Waddlia chondrophila they likely originated from Legionellales or Actinomycetales. The acquisition of catalases on several occasions in the Chlamydiales suggests the importance of this enzyme for the bacteria in their host environment.

Incendis històrics a l'alta muntanya pirinenca : anàlisi dels carbons sedimentaris a la torbera de Montarenyo (Lladorre, Pallars Sobirà)

Les zones europees d’alta muntanya, concretament les mediterrànies, han estat utilitzades des de temps remots per l’ésser humà, a través de l’aprofitament de boscos i prats mitjançant activitats com l’agricultura, la ramaderia, la silvicultura i la metal·lúrgia. Però, des de fa temps, amb l’abandonament de les àrees rurals, estem davant d’una falta de gestió dels boscos, degut a la pèrdua de les activitats tradicionals. L’objectiu d’aquest treball és el de determinar l’impacte provocat per les societats antigues sobre els boscos, amb la utilització del foc com a eina de gestió, així com l’anàlisi dels processos d’antropització de les zones de muntanya que utilitzaven aquest recurs. En aquest treball l’anàlisi de l’evolució del paisatge es fa mitjançant l’estudi de les comunitats vegetals històriques i la dinàmica d’incendis, a través de dues metodologies basades en testimonis sedimentaris: l’anàlisi de carbons i l’anàlisi del pol·len. El testimoni sedimentari ha estat extret de la torbera ombrotròfica de Montarenyo, situada a la vessant sud dels Pirineus, a la Vall de Cardós, al Pallars Sobirà. Aquestes dues disciplines han permès indagar en la geohistòria ambiental, per tal d’establir les relacions entre l’ambient i la societat. Els resultats mostren que el foc ha estat utilitzat per nombroses activitats, creant unes dinàmiques forestals característiques. El paisatge actual és conseqüència de les pressions que va haver de patir el bosc durant anys, unes pressions que, amb major o menor mesura han gestionat les masses forestals. Cal doncs conèixer quina ha estat la gestió històrica del bosc per entendre’n el seu estat actual i poder escollir la gestió més adequada per conservar-lo.

Economic and environmental effects of the CO2 taxation: an input-output analysis for Spain

CO2 emissions induced by human activities are the major cause of climate change; hence, strong environmental policy that limits the growing dependence on fossil fuel is indispensable. Tradable permits and environmental taxes are the usual tools used in CO2 reduction strategies. Such economic tools provide incentives to polluting industries to reduce their emissions through market signals. The aim of this work is to investigate the direct and indirect effects of an environmental tax on Spanish products and services. We apply an environmentally extended input-output (EIO) model to identify CO2 emission intensities of products and services and, accordingly, we estimate the tax proportional to these intensities. The short-term price effects are analyzed using an input-output price model. The effect of tax introduction on consumption prices and its influence on consumers’ welfare are determined. We also quantify the environmental impacts of such taxation in terms of the reduction in CO2 emissions. The results, based on the Spanish economy for the year 2007, show that sectors with relatively poor environmental profile are subjected to high environmental tax rates. And consequently, applying a CO2 tax on these sectors, increases production prices and induces a slight increase in consumer price index and a decrease in private welfare. The revenue from the tax could be used to counter balance the negative effects on social welfare and also to stimulate the increase of renewable energy shares in the most impacting sectors. Finally, our analysis highlights that the environmental and economic goals cannot be met at the same time with the environmental taxation and this shows the necessity of finding other (complementary or alternative) measures to ensure both the economic and ecological efficiencies. Keywords: CO2 emissions; environmental tax; input-output model, effects of environmental taxation.

Dose-dependent influence of didanosine on immune recovery in HIV-infected patients treated with tenofovir.

BACKGROUND: Antiretroviral therapy (ART) containing tenofovir disoproxil fumarate (TDF) and didanosine (ddI) has been associated with poor immune recovery despite virologic success. This effect might be related to ddI toxicity since ddI exposure is substantially increased by TDF. OBJECTIVE: To analyze whether immune recovery during ART with TDF and ddI is ddI-dose dependent. DESIGN AND METHODS: A retrospective longitudinal analysis of immune recovery measured by the CD4 T-cell slope in 614 patients treated with ART containing TDF with or without ddI. Patients were stratified according to the tertiles of their weight-adjusted ddI dose: low dose (< 3.3 mg/kg), intermediate dose (3.3-4.1 mg/kg) and high dose (> 4.1 mg/kg). Cofactors modifying the degree of immune recovery after starting TDF-containing ART were identified by univariable and multivariable linear regression analyses. RESULTS: CD4 T-cell slopes were comparable between patients treated with TDF and a weight-adjusted ddI-dose of < 4.1 mg/kg per day (n = 143) versus TDF-without-ddI (n = 393). In the multivariable model the slopes differed by -13 CD4 T cells/mul per year [95% confidence interval (CI), -42 to 17; P = 0.40]. In contrast, patients treated with TDF and a higher ddI dose (> 4.1 mg/kg per day, n = 78) experienced a significantly impaired immune recovery (-47 CD4 T cells/microl per year; 95% CI, -82 to -12; P = 0.009). The virologic response was comparable between the different treatment groups. CONCLUSIONS: Immune recovery is impaired, when high doses of ddI (> 4.1 mg/kg) are given in combination with TDF. If the dose of ddI is adjusted to less than 4.1 mg/kg per day, immune recovery is similar to other TDF-containing ART regimen.

Debris flow susceptibility mapping at a regional scale along the National Road N7, Argentina

A first assessment of debris flow susceptibility at a large scale was performed along the National Road N7, Argentina. Numerous catchments are prone to debris flows and likely to endanger the road-users. A 1:50,000 susceptibility map was created. The use of a DEM (grid 30 m) associated to three complementary criteria (slope, contributing area, curvature) allowed the identification of potential source areas. The debris flow spreading was estimated using a process- and GISbased model (Flow-R) based on basic probabilistic and energy calculations. The best-fit values for the coefficient of friction and the mass-to-drag ratio of the PCM model were found to be ? = 0.02 and M/D = 180 and the resulting propagation on one of the calibration site was validated using the Coulomb friction model. The results are realistic and will be useful to determine which areas need to be prioritized for detailed studies.

A model for physical activity, bahaviour and energy expenditure assessment in real-life condition

RésuméL'origine de l'obésité, qui atteint des proportions épidémiques, est complexe. Elle est liée au mode de vie et au comportement des individus par rapport à l'activité physique, expression des choix individuels et de l'interaction avec l'environnement. Les mesures du comportement au niveau de l'activité physique des individus face à leur environnement, la répartition des types d'activité physique, la durée, la fréquence, l'intensité, et la dépense énergétique sont d'une grande importance. Aujourd'hui, il y a un manque de méthodes permettant une évaluation précise et objective de l'activité physique et du comportement des individus. Afin de compléter les recherches relatives à l'activité physique, à l'obésité et à certaines maladies, le premier objectif du travail de thèse était de développer un modèle pour l'identification objective des types d'activité physique dans des conditions de vie réelles et l'estimation de la dépense énergétique basée sur une combinaison de 2 accéléromètres et 1 GPS. Le modèle prend en compte qu'une activité donnée peut être accomplie de différentes façons dans la vie réelle. Les activités quotidiennes ont pu être classées en 8 catégories, de sédentaires à actives, avec une précision de 1 min. La dépense énergétique a pu peut être prédite avec précision par le modèle. Après validation du modèle, le comportement des individus de l'activité physique a été évalué dans une seconde étude. Nous avons émis l'hypothèse que, dans un environnement caractérisé par les pentes, les personnes obèses sont tentées d'éviter les pentes raides et de diminuer la vitesse de marche au cours d'une activité physique spontanée, ainsi que pendant les exercices prescrits et structurés. Nous avons donc caractérisé, par moyen du modèle développé, le comportement des individus obèses dans un environnement vallonné urbain. La façon dont on aborde un environnement valloné dans les déplacements quotidiens devrait également être considérée lors de la prescription de marche supplémentaire afin d'augmenter l'activité physique.SummaryOrigin of obesity, that reached epidemic proportion, is complex and may be linked to different lifestyle and physical activity behaviour. Measurement of physical activity behaviour of individuals towards their environment, the distribution of physical activity in terms of physical activity type, volume, duration, frequency, intensity, and energy expenditure is of great importance. Nowadays, there is a lack of methods for accurate and objective assessment of physical activity and of individuals' physical activity behaviour. In order to complement the research relating physical activity to obesity and related diseases, the first aim of the thesis work was to develop a model for objective identification of physical activity types in real-life condition and energy expenditure based on a combination of 2 accelerometers and 1 GPS device. The model takes into account that a given activity can be achieved in many different ways in real life condition. Daily activities could be classified in 8 categories, as sedentary to active physical activity, within 1 min accuracy, and physical activity patterns determined. The energy expenditure could be predicted accurately with an accuracy below 10%. Furthermore, individuals' physical activity behaviour is expression of individual choices and their interaction with the neighbourhood environment. In a second study, we hypothesized that, in an environment characterized by inclines, obese individuals are tempted to avoid steep positive slopes and to decrease walking speed during spontaneous outdoor physical activity, as well as during prescribed structured bouts of exercise. Finally, we characterized, by mean of the developed model, the physical activity behaviour of obese individuals in a hilly urban environment. Quantifying how one tackles hilly environment or avoids slope in their everyday displacements should be also considered while prescribing extra walking in free-living conditions in order to increase physical activity.

Evolution of a debris flow channel monitored using a 3D terrestrial laser scanner

Like numerous torrents in mountainous regions, the Illgraben creek (canton of Wallis, SW Switzerland) produces almost every year several debris flows. The total area of the active catchment is only 4.7 km², but large events ranging from 50'000 to 400'000 m³ are common (Zimmermann 2000). Consequently, the pathway of the main channel often changes suddenly. One single event can for instance fill the whole river bed and dig new several-meters-deep channels somewhere else (Bardou et al. 2003). The quantification of both, the rhythm and the magnitude of these changes, is very important to assess the variability of the bed's cross section and long profile. These parameters are indispensable for numerical modelling, as they should be considered as initial conditions. To monitor the channel evolution an Optech ILRIS 3D terrestrial laser scanner (LIDAR) was used. LIDAR permits to make a complete high precision 3D model of the channel and its surroundings by scanning it from different view points. The 3D data are treated and interpreted with the software Polyworks from Innovmetric Software Inc. Sequential 3D models allow for the determination of the variation in the bed's cross section and long profile. These data will afterwards be used to quantify the erosion and the deposition in the torrent reaches. To complete the chronological evolution of the landforms, precise digital terrain models, obtained by high resolution photogrammetry based on old aerial photographs, will be used. A 500 m long section of the Illgraben channel was scanned on 18th of August 2005 and on 7th of April 2006. These two data sets permit identifying the changes of the channel that occurred during the winter season. An upcoming scanning campaign in September 2006 will allow for the determination of the changes during this summer. Preliminary results show huge variations in the pathway of the Illgraben channel, as well as important vertical and lateral erosion of the river bed. Here we present the results of a river bank on the left (north-western) flank of the channel (Figure 1). For the August 2005 model the scans from 3 viewpoints were superposed, whereas the April 2006 3D image was obtained by combining 5 separate scans. The bank was eroded. The bank got eroded essentially on its left part (up to 6.3 m), where it is hit by the river and the debris flows (Figures 2 and 3). A debris cone has also formed (Figure 3), which suggests that a part of the bank erosion is due to shallow landslides. They probably occur when the river erosion creates an undercut slope. These geometrical data allow for the monitoring of the alluvial dynamics (i.e. aggradation and degradation) on different time scales and the influence of debris flows occurrence on these changes. Finally, the resistance against erosion of the bed's cross section and long profile will be analysed to assess the variability of these two key parameters. This information may then be used in debris flow simulation.

Identification of potential rockfall source areas at a regional scale using a DEM-based geomorphometric analysis

The availability of high resolution Digital Elevation Models (DEM) at a regional scale enables the analysis of topography with high levels of detail. Hence, a DEM-based geomorphometric approach becomes more accurate for detecting potential rockfall sources. Potential rockfall source areas are identified according to the slope angle distribution deduced from high resolution DEM crossed with other information extracted from geological and topographic maps in GIS format. The slope angle distribution can be decomposed in several Gaussian distributions that can be considered as characteristic of morphological units: rock cliffs, steep slopes, footslopes and plains. A terrain is considered as potential rockfall sources when their slope angles lie over an angle threshold, which is defined where the Gaussian distribution of the morphological unit "Rock cliffs" become dominant over the one of "Steep slopes". In addition to this analysis, the cliff outcrops indicated by the topographic maps were added. They contain however "flat areas", so that only the slope angles values above the mode of the Gaussian distribution of the morphological unit "Steep slopes" were considered. An application of this method is presented over the entire Canton of Vaud (3200 km2), Switzerland. The results were compared with rockfall sources observed on the field and orthophotos analysis in order to validate the method. Finally, the influence of the cell size of the DEM is inspected by applying the methodology over six different DEM resolutions.

Application of low temperature thermochronology to understanding cooling and exhumation in the Central Swiss Alps

THESIS ABSTRACT : Low-temperature thermochronology relies on application of radioisotopic systems whose closure temperatures are below temperatures at which the dated phases are formed. In that sense, the results are interpreted as "cooling ages" in contrast to "formation ages". Owing to the low closure-temperatures, it is possible to reconstruct exhumation and cooling paths of rocks during their residence at shallow levels of the crust, i.e. within first ~10 km of depth. Processes occurring at these shallow depths such as final exhumation, faulting and relief formation are fundamental for evolution of the mountain belts. This thesis aims at reconstructing the tectono-thermal history of the Aar massif in the Central Swiss Alps by means of zircon (U-Th)/He, apatite (U-Th)/He and apatite fission track thermochronology. The strategy involved acquisition of a large number of samples from a wide range of elevations in the deeply incised Lötschen valley and a nearby NEAT tunnel. This unique location allowed to precisely constrain timing, amount and mechanisms of exhumation of the main orographic feature of the Central Alps, evaluate the role of topography on the thermochronological record and test the impact of hydrothermal activity. Samples were collected from altitudes ranging between 650 and 3930 m and were grouped into five vertical profiles on the surface and one horizontal in the tunnel. Where possible, all three radiometric systems were applied to each sample. Zircon (U-Th)/He ages range from 5.1 to 9.4 Ma and are generally positively correlated with altitude. Age-elevation plots reveal a distinct break in slope, which translates into exhumation rate increasing from ~0.4 to ~3 km/Ma at 6 Ma. This acceleration is independently confirmed by increased cooling rates on the order of 100°C/Ma constrained on the basis of age differences between the zircon (U-Th)/He and the remaining systems. Apatite fission track data also plot on a steep age-elevation curve indicating rapid exhumation until the end of the Miocene. The 6 Ma event is interpreted as reflecting tectonically driven uplift of the Aar massif. The late Miocene timing implies that the increase of precipitation in the Pliocene did not trigger rapid exhumation in the Aar massif. The Messinian salinity crisis in the Mediterranean could not directly intensify erosion of the Aar but associated erosional output from the entire Alps may have tapered the orogenic wedge and caused reactivation of thrusting in the Aar massif. The high exhumation rates in the Messinian were followed by a decrease to ~1.3 km/Ma as evidenced by ~8 km of exhumation during last 6 Ma. The slowing of exhumation is also apparent from apatite (U-Th)1He age-elevation data in the northern part of the Lötschen valley where they plot on a ~0.5km/Ma line and range from 2.4 to 6.4 Ma However, from the apatite (U-Th)/He and fission track data from the NEAT tunnel, there is an indication of a perturbation of the record. The apatite ages are youngest under the axis of the valley, in contrast to an expected pattern where they would be youngest in the deepest sections of the tunnel due to heat advection into ridges. The valley however, developed in relatively soft schists while the ridges are built of solid granitoids. In line with hydrological observations from the tunnel, we suggest that the relatively permeable rocks under the valley floor, served as conduits of geothermal fluids that caused reheating leading to partial Helium loss and fission track annealing in apatites. In consequence, apatite ages from the lowermost samples are too young and the calculated exhumation rates may underestimate true values. This study demonstrated that high-density sampling is indispensable to provide meaningful thermochronological data in the Alpine setting. The multi-system approach allows verifying plausibility of the data and highlighting sources of perturbation. RÉSUMÉ DE THÈSE : La thermochronologie de basse température dépend de l'utilisation de systèmes radiométriques dont la température de fermeture est nettement inférieure à la température de cristallisation du minéral. Les résultats obtenus sont par conséquent interprétés comme des âges de refroidissement qui diffèrent des âges de formation obtenus par le biais d'autres systèmes de datation. Grâce aux températures de refroidissement basses, il est aisé de reconstruire les chemins de refroidissement et d'exhumation des roches lors de leur résidence dans la croute superficielle (jusqu'à 10 km). Les processus qui entrent en jeu à ces faibles profondeurs tels que l'exhumation finale, la fracturation et le faillage ainsi que la formation du relief sont fondamentaux dans l'évolution des chaînes de montagne. Ces dernières années, il est devenu clair que l'enregistrement thermochronologique dans les orogènes peut être influencé par le relief et réinitialisé par l'advection de la chaleur liée à la circulation de fluides géothermaux après le refroidissement initial. L'objectif de cette thèse est de reconstruire l'histoire tectono-thermique du massif de l'Aar dans les Alpes suisses Centrales à l'aide de trois thermochronomètres; (U-Th)/He sur zircon, (U-Th)/He sur apatite et les traces de fission sur apatite. Afin d'atteindre cet objectif, nous avons récolté un grand nombre d'échantillons provenant de différentes altitudes dans la vallée fortement incisée de Lötschental ainsi que du tunnel de NEAT. Cette stratégie d'échantillonnage nous a permis de contraindre de manière précise la chronologie, les quantités et les mécanismes d'exhumation de cette zone des Alpes Centrales, d'évaluer le rôle de la topographie sur l'enregistrement thermochronologique et de tester l'impact de l'hydrothermalisme sur les géochronomètres. Les échantillons ont été prélevés à des altitudes comprises entre 650 et 3930m selon 5 profils verticaux en surface et un dans le tunnel. Quand cela à été possible, les trois systèmes radiométriques ont été appliqués aux échantillons. Les âges (U-Th)\He obtenus sur zircons sont compris entre 5.l et 9.4 Ma et sont corrélés de manière positive avec l'altitude. Les graphiques représentant l'âge et l'élévation montrent une nette rupture de la pente qui traduisent un accroissement de la vitesse d'exhumation de 0.4 à 3 km\Ma il y a 6 Ma. Cette accélération de l'exhumation est confirmée par les vitesses de refroidissement de l'ordre de 100°C\Ma obtenus à partir des différents âges sur zircons et à partir des autres systèmes géochronologiques. Les données obtenues par traces de fission sur apatite nous indiquent également une exhumation rapide jusqu'à la fin du Miocène. Nous interprétons cet évènement à 6 Ma comme étant lié à l'uplift tectonique du massif de l'Aar. Le fait que cet évènement soit tardi-miocène implique qu'une augmentation des précipitations au Pliocène n'a pas engendré cette exhumation rapide du massif de l'Aar. La crise Messinienne de la mer méditerranée n'a pas pu avoir une incidence directe sur l'érosion du massif de l'Aar mais l'érosion associée à ce phénomène à pu réduire le coin orogénique alpin et causer la réactivation des chevauchements du massif de l'Aar. L'exhumation rapide Miocène a été suivie pas une diminution des taux d'exhumation lors des derniers 6 Ma (jusqu'à 1.3 km\Ma). Cependant, les âges (U-Th)\He sur apatite ainsi que les traces de fission sur apatite des échantillons du tunnel enregistrent une perturbation de l'enregistrement décrit ci-dessus. Les âges obtenus sur les apatites sont sensiblement plus jeunes sous l'axe de la vallée en comparaison du profil d'âges attendus. En effet, on attendrait des âges plus jeunes sous les parties les plus profondes du tunnel à cause de l'advection de la chaleur dans les flancs de la vallée. La vallée est creusée dans des schistes alors que les flancs de celle-ci sont constitués de granitoïdes plus durs. En accord avec les observations hydrologiques du tunnel, nous suggérons que la perméabilité élevée des roches sous l'axe de la vallée à permi l'infiltration de fluides géothermaux qui a généré un réchauffement des roches. Ce réchauffement aurait donc induit une perte d'Hélium et un recuit des traces de fission dans les apatites. Ceci résulterait en un rajeunissement des âges apatite et en une sous-estimation des vitesses d'exhumation sous l'axe de la vallée. Cette étude à servi à démontrer la nécessité d'un échantillonnage fin et précis afin d'apporter des données thermochronologiques de qualité dans le contexte alpin. Cette approche multi-système nous a permi de contrôler la pertinence des données acquises ainsi que d'identifier les sources possibles d'erreurs lors d'études thermochronologiques. RÉSUMÉ LARGE PUBLIC Lors d'une orogenèse, les roches subissent un cycle comprenant une subduction, de la déformation, du métamorphisme et, finalement, un retour à la surface (ou exhumation). L'exhumation résulte de la déformation au sein de la zone de collision, menant à un raccourcissement et un apaissessement de l'édifice rocheux, qui se traduit par une remontée des roches, création d'une topographie et érosion. Puisque l'érosion agit comme un racloir sur la partie supérieure de l'édifice, des tentatives de corrélation entre les épisodes d'exhumation rapide et les périodes d'érosion intensive, dues aux changements climatiques, ont été effectuées. La connaissance de la chronologie et du lieu précis est d'une importance capitale pour une quelconque reconstruction de l'évolution d'une chaîne de montagne. Ces critères sont donnés par un retraçage des changements de la température de la roche en fonction du temps, nous donnant le taux de refroidissement. L'instant auquel les roches ont refroidit, passant une certaine température, est contraint par l'application de techniques de datation par radiométrie. Ces méthodes reposent sur la désintégration des isotopes radiogéniques, tels que l'uranium et le potassium, tous deux abondants dans les roches de la croûte terrestre. Les produits de cette désintégration ne sont pas retenus dans les minéraux hôtes jusqu'au moment du refroidissement de la roche sous une température appelée 'de fermeture' , spécifique à chaque système de datation. Par exemple, la désintégration radioactive des atomes d'uranium et de thorium produit des atomes d'hélium qui s'échappent d'un cristal de zircon à des températures supérieures à 200°C. En mesurant la teneur en uranium-parent, l'hélium accumulé et en connaissant le taux de désintégration, il est possible de calculer à quel moment la roche échantillonnée est passée sous la température de 200°C. Si le gradient géothermal est connu, les températures de fermeture peuvent être converties en profondeurs actuelles (p. ex. 200°C ≈ 7km), et le taux de refroidissement en taux d'exhumation. De plus, en datant par système radiométrique des échantillons espacés verticalement, il est possible de contraindre directement le taux d'exhumation de la section échantillonnée en observant les différences d'âges entre des échantillons voisins. Dans les Alpes suisses, le massif de l'Aar forme une structure orographique majeure. Avec des altitudes supérieures à 4000m et un relief spectaculaire de plus de 2000m, le massif domine la partie centrale de la chaîne de montagne. Les roches aujourd'hui exposées à la surface ont été enfouies à plus de 10 km de profond il y a 20 Ma, mais la topographie actuelle du massif de l'Aar semble surtout s'être développée par un soulèvement actif depuis quelques millions d'années, c'est-à-dire depuis le Néogène supérieur. Cette période comprend un changement climatique soudain ayant touché l'Europe il y a environ 5 Ma et qui a occasionné de fortes précipitations, entraînant certainement une augmentation de l'érosion et accélérant l'exhumation des Alpes. Dans cette étude, nous avons employé le système de datation (U-TH)/He sur zircon, dont la température de fermeture de 200°C est suffisamment basse pour caractériser l'exhumation du Néogène sup. /Pliocène. Les échantillons proviennent du Lötschental et du tunnel ferroviaire le plus profond du monde (NEAT) situé dans la partie ouest du massif de l'Aar. Considérés dans l'ensemble, ces échantillons se répartissent sur un dénivelé de 3000m et des âges de 5.1 à 9.4 Ma. Les échantillons d'altitude supérieure (et donc plus vieux) documentent un taux d'exhumation de 0.4 km/Ma jusqu'à il y a 6 Ma, alors que les échantillons situés les plus bas ont des âges similaires allant de 6 à 5.4 Ma, donnant un taux jusqu'à 3km /Ma. Ces données montrent une accélération dramatique de l'exhumation du massif de l'Aar il y a 6 Ma. L'exhumation miocène sup. du massif prédate donc le changement climatique Pliocène. Cependant, lors de la crise de salinité d'il y a 6-5.3 Ma (Messinien), le niveau de la mer Méditerranée est descendu de 3km. Un tel abaissement de la surface d'érosion peut avoir accéléré l'exhumation des Alpes, mais le bassin sud alpin était trop loin du massif de l'Aar pour influencer son érosion. Nous arrivons à la conclusion que la datation (U-Th)/He permet de contraindre précisément la chronologie et l'exhumation du massif de l'Aar. Concernant la dualité tectonique-érosion, nous suggérons que, dans le cas du massif de l'Aar, la tectonique prédomine.

Three-dimensional sequence stratigraphy and subtle stratigraphic traps associated with systems tracts: West Cameron region, offshore Louisiana, Gulf of Mexico

Three-dimensional sequence stratigraphy is a potent exploration and development tool for the discovery of subtle stratigraphic traps. Reservoir morphology, heterogeneity and subtle stratigraphic trapping mechanisms can be better understood through systematic horizontal identification of sedimentary facies of systems tracts provided by three-dimensional attribute maps used as an important complement to the sequential analysis on the two-dimensional seismic lines and the well log data. On new prospects as well as on already-producing fields, the additional input of sequential analysis on three-dimensional data enables the identification, location and precise delimitation of new potentially productive zones. The first part of this paper presents four typical horizontal seismic facies assigned to the successive systems tracts of a third- or fourth-order sequence deposited in inner to outer neritic conditions on a elastic shelf. The construction of this synthetic representative sequence is based on the observed reproducibility of the horizontal seismic facies response to cyclic eustatic events on more than 35 sequences registered in the Gulf coast Plio-Pleistocene and Late Miocene, offshore Louisiana in the West Cameron region of the Gulf of Mexico. The second part shows how three-dimensional sequence stratigraphy can contribute in localizing and understanding sedimentary facies associated with productive zones. A case study in the early Middle Miocene Cibicides opima sands shows multiple stacked gas accumulations in the top slope fan, prograding wedge and basal transgressive systems tract of the third-order sequence between SB15.5 and SB 13.8 Ma.

Isokinetic rotator muscles fatigue in glenohumeral joint instability before and after Latarjet surgery: a pilot prospective study.

We aimed to analyze the changes in isokinetic internal (IR) and external (ER) rotator muscles fatigue (a) in patients with non-operated recurrent anterior instability, and (b) before and after shoulder surgical stabilization with the Bristow-Latarjet procedure. Thirty-seven patients with non-operated unilateral recurrent anterior post-traumatic instability (NG) were compared with 12 healthy subjects [control group (CG)]. Twenty patients with operated recurrent anterior instability group (OG) underwent isokinetic evaluation before and 3, 6, and 21 months after Bristow-Latarjet surgery. IR and ER muscles strength was evaluated with Con-Trex® dynamometer, with subjects seated and at a 45° shoulder abduction angle in scapular plane. IR and ER muscle fatigue was determined after 10 concentric repetitions at 180° · s(-1) through the fatigue index, the percent decrease in performance (DP), and the slope of peak torque decrease. There were no differences in rotator muscles fatigue between NG and CG. In OG, 3 months post-surgery, IR DP of operated shoulder was significantly (P < 0.001) higher than presurgery and 6 and 21 months post-surgery. Rotator muscles fatigability was not associated with recurrent anterior instability. After surgical stabilization, there was a significantly higher IR fatigability in the operated shoulder 3 months post-surgery, followed by recovery evidenced 6 months post-surgery and long-term maintenance over 21 months.