917 resultados para Self-assembled films


Relevância:

80.00% 80.00%

Publicador:

Resumo:

The present thesis develops from the point of view of titania sol-gel chemistry and an attempt is made to address the modification of the process for better photoactive titania by selective doping and also demonstration of utilization of the process for the preparation of supported membranes and self cleaning films.A general introduction to nanomaterials, nanocrystalline titania and sol-gel chemistry are presented in the first chapter. A brief and updated literature review on sol-gel titania, with special emphasis on catalytic and photocatalytic properties and anatase to rutile transformation are covered. Based on critical assessment of the reported information the present research problem has been defined.The second chapter describes a new aqueous sol-gel method for the preparation of nanocrystalline titania using titanyl sulphate as precursor. This approach is novel since no earlier work has been reported in the same lines proposed here. The sol-gel process has been followed at each step using particle size, zeta potential measurements on the sol and thermal analysis of the resultant gel. The prepared powders were then characterized using X-ray diffraction, FTIR, BET surface area analysis and transmission electron microscopy.The third chapter presents a detailed discussion on the physico-chemical characterization of the aqueous sol-gel derived doped titania. The effect of dopants such as tantalum, gadolinium and ytterbium on the anatase to rutile phase transformation, surface area as well as their influence on photoactivity is also included. The fourth chapter demonstrates application of the aqueous sol-gel method in developing titania coatings on porous alumina substrates for controlling the poresize for use as membrane elements in ultrafiltration. Thin coatings having ~50 nm thickness and transparency of ~90% developed on glass surface were tested successfully for self cleaning applications.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

We have employed time-dependent local-spin-density theory to analyze the far-infrared transmission spectrum of InAs self-assembled nanoscopic rings recently reported [A. Lorke et al., Phys. Rev. Lett. (to be published)]. The overall agreement between theory and experiment is fairly good, which on the one hand confirms that the experimental peaks indeed reflect the ringlike structure of the sample, and on the other hand, asseses the suitability of the theoretical method to describe such nanostructures. The addition energies of one- and two-electron rings are also reported and compared with the corresponding capacitance spectra

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Gelation provides a unique medium, which often induces organization of molecules resulting in the modulation of their optical, morphological and electronic properties thereby opening a new world of fascinating materials with interesting physical properties at nano- meso- and macroscopic levels. Supramolecular gels based on linear π-systems have attracted much attention due to their inherent optical and electronic properties which find application in organic electronics, light harvesting and sensing. They exhibit reversible properties due to the dynamic nature of noncovalent forces. As a result, studies on such soft materials are currently a topic of great interest. Recently, researchers are actively involved in the development of sensors and stimuli-responsive materials based on self-assembled π-systems, which are also called smart materials. The present thesis is divided into four chapters

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Für die Entwicklung selbstorganisierter Monoschichten (SAMs) auf Gold(111)-Oberflächen wurden neue, redox-funktionalisierte Schwefel-Tripodliganden synthetisiert. Um die tripodale Struktur zu realisieren, wurde Adamantan als vierbindiges Zentrum eingesetzt. Die Anbindung an die Goldoberfläche wurde durch Thioethereinheiten ermöglicht, eventuelle laterale Wechselwirkungen durch Alkylseitenketten an den Thioethereinheiten, sowie durch lineare, rigide Spacereinheiten wurden untersucht. Als redoxaktive, funktionelle Einheit wurde ein Ferrocenylrest an den Liganden eingeführt. Gebildete monomolekulare Filme der Liganden auf Gold wurden mit Hilfe von Röntgenphotoelektronenspektroskopie (XPS), Nahkanten-Reflexions-Röntgenabsorptionsspektroskopie (NEXAFS) und Sum-Frequency-Generation (SFG) charakterisiert, um die Filmqualität, die Bindung ans Substrat und Orientierungsordnung im Film zu ermitteln.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Im Vordergrund dieser Arbeit stehen die Synthesen des Azobenzol-4-trichlorsilans sowie des Bis(4-azobenzol)disulfids, ausgehend von einfachen und kommerziell erhältlichen Verbindungen. Moleküle, aus denen sich diese Verbindungen synthetisieren lassen, sind die Iodderivate des Azobenzols, welche über die Kondensation von Benzolaminen (Anilinen) und Nitrosobenzolen dargestellt wurden, aber auch über die altbewährte Azokupplung. Insgesamt wurden 19 neue Azobenzolderivate, das neue [(4-Aminophenyl)ethinyl]ferrocen und das neue Bis[4-(4'-bromazobenzol)]disulfid synthetisiert und charakterisiert. Außerdem wurden 13 neue Kristallstrukturen erzeugt. Mit den synthetisierten Molekülen wurden Substrat-Adsorbat-Systeme gebildet. Als Substrate wurden oberflächenoxidiertes Silizium und Gold gewählt. Die Präparation dieser sogennanten selbstorganisierten Monolagen (SAMs) bzw. der kovalent gebundenen Monolagen im Falle der Trichlorsilylderivate (CAMs) wurde eingehend studiert. Das Azobenzol wurde als photoschaltbare Einheit gewählt, da es bereits Kern zahlreicher Untersuchungen war und als solcher als guter und zuverlässiger Baustein für reversible photoschaltbare Systeme etabliert ist. Zur Charakterisierung Schichten und zur Untersuchung ihres photoresponsiven Verhaltens sowie sowie zur Untersuchung der Schichtbildung selbst wurden mehrere physikalische Messmethoden angewandt. Die Schichtbildung wurde mit SHG (optische Frequenzverdopplung) verfolgt, die fertigen Schichten wurden mit XPS (Röntgen-Photonen-Spektroskopie) und NEXAFS (Nahkanten-Röntgen-Absorptions-Feinstruktur) untersucht, um Orientierung und Ordnung der Moleküle in der Schicht zu ermitteln. Das Schaltverhalten wurde mit Ellipsometrie und durch Messungen des Wasserkontaktwinkels beobachtet. Durch Variation der Endgruppe des Azobenzols ist es möglich, die Oberflächeneigenschaften einstellen gezielt zu können, wie Hydrophobie, Hydrophilie, Komplexierungsverhalten oder elektrische Schaltbarkeit. Dies gelingt durch Gruppen wie N,N-Dimethylamino-, Methoxy-, Ethoxy-, Octyloxy-, Dodecyloxy-, Benzyloxy-, Methyl-, Trifluormethyl-, Pyridyl-, Phenylethinyl- und Ferrocenyl-Restgruppen, um nur eine Auswahl zu nennen. Einerseits wurde Silizium als Substrat gewählt, da es wegen seiner Verwendung in der Halbleiterindustrie ein nicht uninteressantes Substrat darstell und die Möglichkeiten der kovalenten Anbindung von Trichlorsilanen aber auch Trialkoxysilanen auch gut untersucht ist. Andererseits wurden auch Untersuchungen mit Gold als Substrat angestellt, bei dem Thiole und Disulfide die bevorzugten Ankergruppen bilden. Während sich auf Gold sogenannte SAMs bilden, verleiht die kovalente Siloxanbindung den CAMs auf Silizium eine besondere Stabilität.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Among organic materials, spirobifluorene derivatives represent a very attractive class of materials for electronic devices. These compounds have high melting points, glass transitions temperatures and morphological stability, which makes these materials suitable for organic electronic applications. In addition, some of spirobifluorenes can form porous supramolecular associations with significant volumes available for the inclusion of guests. These molecular associations based on the spirobifluorenes are noteworthy because they are purely molecular analogues of zeolites and other microporous solids, with potential applications in separation, catalysis, sensing and other areas.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

The main focus and concerns of this PhD thesis is the growth of III-V semiconductor nanostructures (Quantum dots (QDs) and quantum dashes) on silicon substrates using molecular beam epitaxy (MBE) technique. The investigation of influence of the major growth parameters on their basic properties (density, geometry, composition, size etc.) and the systematic characterization of their structural and optical properties are the core of the research work. The monolithic integration of III-V optoelectronic devices with silicon electronic circuits could bring enormous prospect for the existing semiconductor technology. Our challenging approach is to combine the superior passive optical properties of silicon with the superior optical emission properties of III-V material by reducing the amount of III-V materials to the very limit of the active region. Different heteroepitaxial integration approaches have been investigated to overcome the materials issues between III-V and Si. However, this include the self-assembled growth of InAs and InGaAs QDs in silicon and GaAx matrices directly on flat silicon substrate, sitecontrolled growth of (GaAs/In0,15Ga0,85As/GaAs) QDs on pre-patterned Si substrate and the direct growth of GaP on Si using migration enhanced epitaxy (MEE) and MBE growth modes. An efficient ex-situ-buffered HF (BHF) and in-situ surface cleaning sequence based on atomic hydrogen (AH) cleaning at 500 °C combined with thermal oxide desorption within a temperature range of 700-900 °C has been established. The removal of oxide desorption was confirmed by semicircular streaky reflection high energy electron diffraction (RHEED) patterns indicating a 2D smooth surface construction prior to the MBE growth. The evolution of size, density and shape of the QDs are ex-situ characterized by atomic-force microscopy (AFM) and transmission electron microscopy (TEM). The InAs QDs density is strongly increased from 108 to 1011 cm-2 at V/III ratios in the range of 15-35 (beam equivalent pressure values). InAs QD formations are not observed at temperatures of 500 °C and above. Growth experiments on (111) substrates show orientation dependent QD formation behaviour. A significant shape and size transition with elongated InAs quantum dots and dashes has been observed on (111) orientation and at higher Indium-growth rate of 0.3 ML/s. The 2D strain mapping derived from high-resolution TEM of InAs QDs embedded in silicon matrix confirmed semi-coherent and fully relaxed QDs embedded in defectfree silicon matrix. The strain relaxation is released by dislocation loops exclusively localized along the InAs/Si interfaces and partial dislocations with stacking faults inside the InAs clusters. The site controlled growth of GaAs/In0,15Ga0,85As/GaAs nanostructures has been demonstrated for the first time with 1 μm spacing and very low nominal deposition thicknesses, directly on pre-patterned Si without the use of SiO2 mask. Thin planar GaP layer was successfully grown through migration enhanced epitaxy (MEE) to initiate a planar GaP wetting layer at the polar/non-polar interface, which work as a virtual GaP substrate, for the GaP-MBE subsequently growth on the GaP-MEE layer with total thickness of 50 nm. The best root mean square (RMS) roughness value was as good as 1.3 nm. However, these results are highly encouraging for the realization of III-V optical devices on silicon for potential applications.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Aufbauend auf den Arbeiten von Bielawski et al. und Siemeling et al. wurden im Rahmen dieser Arbeit unsymmetrisch substituierte N-heterocyclische Carbene mit einem 1,1ʹ-Ferrocendiyl-Rückgrat synthetisiert. Ausgehend von der literaturbekannten Verbindung 1,1’-Diaminoferrocen gelang die Einführung der exocyclischen Substituenten an den Stickstoffatomen lediglich durch die Anpassung der Stöchiometrie in den einzelnen Syntheseschritten. Es wurden die folgenden drei NHCs synthetisiert: N-(2-Adamantyl)-N’-neopentyldiaminocarben[3]ferrocenophan (Ad/Np), N-Neopentyl-N’-phenyldiaminocarben[3]ferrocenophan (Ph/Np) und N-(9-Anthracenylmethyl)-N’-neopentyldiaminocarben[3]ferrocenophan (Acm/Np). Das Carben Ad/Np konnte dabei erfolgreich isoliert werden, während die anderen zwei Carbene als Liganden in Komplexen des Typs [RhCl(COD)(NHC)] stabilisiert wurden. Von allen drei Carbenen wurden Rhodium-Carben-Komplexe des Typs [RhCl(COD)(NHC)] und cis-[RhCl(CO)2(NHC)] synthetisiert. Anhand der röntgenkristallographischen und NMR-spektroskopischen Untersuchungen dieser Rhodiumkomplexe konnten in allen sechs Komplexen anagostische Wechselwirkungen zwischen dem zentralen Rhodiumatom und den Wasserstoffatomen der exocyclischen Substituenten, die sich in α-Position zu den Stickstoffatomen befinden, nachgewiesen werden. Des Weiteren wurden anhand der cis-[RhCl(CO)2(NHC)]-Komplexe die TEP-Werte der Carbene bestimmt. Gemessen in DCM betragen diese 2049 cm-1 (Ad/Np), 2049 cm-1 (Ph/Np) und 2051 cm-1 (Acm/Np). Unabhängig von den unsymmetrisch substituierten NHCs mit einem 1,1ʹ-Ferrocendiyl-Rückgrat wurde im Rahmen dieser Arbeit die Eignung von NHCs als Adsorbatspezies für selbstorganisierende Monolagen überprüft. Hierzu wurden Tetraalkylimidazol-2-ylidene synthetisiert, welche als 0.01 mM Lösung auf Gold(111)-Substrate aufgebracht wurden. Die Goldsubstrate wurden anschließend mittels XPS untersucht. Die XPS-Analyse der modifizierten Goldsubstrate zeigte, dass eine Bindung der Carbene auf der Oberfläche stattgefunden hat. Es zeigte sich allerdings auch, dass keine SAM gebildet wurden, da die Oberfläche signifikant mit kohlen- und sauerstoffbasierten Verbindungen kontaminiert ist. Dabei kann vermutet werden, dass die Carbene nicht ausschließlich auf der Goldoberfläche selbst, sondern auch mit den auf der Oberfläche befindlichen Verbindungen reagiert haben.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

High density, uniform GaN nanodot arrays with controllable size have been synthesized by using template-assisted selective growth. The GaN nanodots with average diameter 40nm, 80nm and 120nm were selectively grown by metalorganic chemical vapor deposition (MOCVD) on a nano-patterned SiO2/GaN template. The nanoporous SiO2 on GaN surface was created by inductively coupled plasma etching (ICP) using anodic aluminum oxide (AAO) template as a mask. This selective regrowth results in highly crystalline GaN nanodots confirmed by high resolution transmission electron microscopy. The narrow size distribution and uniform spatial position of the nanoscale dots offer potential advantages over self-assembled dots grown by the Stranski–Krastanow mode.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

La gran eficiència, selectivitat i les condicions suaus exhibides per les reaccions que tenen lloc al centre actiu de les metal·looxigenases són la font d'inspiració per la present dissertació. Amb l'objectiu de dissenyar catalitzadors d'oxidació eficients hem fet ús de dues estratègies: la primera consisteix en el disseny de complexos amb baix pes molecular inspirats en aspectes estructurals de la primera esfera de coordinació del centre metàl·lic d'enzims de ferro i de manganès. Aquests complexos s'han estudiat com a catalitzadors en l'oxidació selectiva d'alcans i d'alquens fent servir oxidants "verds" com ara l'H2O2. La segona estratègia està basada en l'ús de la química supramolecular per tal de desenvolupar estructures moleculars auto-acoblades amb la forma i les propietats químiques desitjades. Concretament, la construcció de nanocontenidors amb un catalitzador d'oxidació incrustat a la seva estructura ens permetria dur a terme reaccions més selectives, tal com passa en les reaccions catalitzades per enzims.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

The ability to generate very stable assemblies via non-covalent interactions has enabled materials to be constructed that were not feasible via traditional covalent bond formation processes. A series of low molecular mass bisurethane and bisurea polymers have been developed that form stable self-assembled networks through hydrogen bonding interactions. Thermo-responsive polymers were generated by end-capping poly(ethylene-co-butylene) or polybutadiene chains with the bisurethane or bisurea motif. Microphase separation is observed via TEM and small-angle X-ray scattering (SAXS) for the modified pseudo polymers and significant differences in the temperature dependence of microphase separation are analysed via SAXS. The importance of the polarity of the end groups is manifested in distinct temperature-dependent microphase separation behaviour. Information on the local hydrogen bonding structure is provided by wide-angle X-ray scattering and variable temperature FTI

Relevância:

80.00% 80.00%

Publicador:

Resumo:

We study the structure and shear flow behavior of a side-on liquid crystalline triblock copolymer, named PBA-b-PA444-b-PBA (PBA is poly(butyl acrylate) and PA444 is a poly(acrylate) with a nematic liquid crystal side-on mesogen), in the self-assembled lamellar phase and in the disordered phase. Simultaneous oscillatory shear and small-angle X-ray scattering experiments show that shearing PBA-b-PA444-b-PBA at high frequency and strain amplitudes leads to the alignment of the lamellae with normals perpendicular to the shear direction and to the velocity gradient direction, i.e., in the perpendicular orientation. The order-to-disorder transition temperature (T-ODT) is independent of the applied strain, in contrast to results reported in the literature for coil-coil diblock copolymers, which show an increase in T-ODT with shear rate. It is possible that in our system, T-ODT does not depend on the applied strain because the fluctuations are weaker than those present in coil-coil diblock copolymer systems.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Solvent induced single-crystal-to-single-crystal transformation has been demonstrated indicating the dynamic behavior of one dimensional arrays obtained from a self-assembled new synthetic cyclic peptide.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

The self-assembly in aqueous solution of a PEG-peptide conjugate is studied by spectroscopy, electron microscopy, rheology and small-angle Xray and neutron scattering (SAXS and SANS). The peptide fragment, FFKLVFF is based on fragment KLVFF of the amyloid beta-peptide, A beta(16-20), extended by two hydrophobic phenylalanine units. This is conjugated to PEG which confers water solubility and leads to distinct self-assembled structures. Small-angle scattering reveals the formation of cylindrical fibrils comprising a peptide core and PEG corona. This constrained structure leads to a model parallel beta-sheet self-assembled structure with a radial arrangement of beta sheets. Oil increasing concentration, successively nematic and hexagonal columnar phases are formed. The flow-induced alignment of both structures was studied in situ by SANS using a Couette cell. Shear-induced alignment is responsible for the shear thinning behaviour observed by dynamic shear rheometry. Incomplete recovery of moduli after cessation of shear is consistent with the observation from SANS of retained orientation in the sample.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Quartz crystal microbalance (QCM) measurements of the formation of a 4-aminothiophenol (4-ATP)self-assembled monolayer (SAM) at a gold electrode showed that a surface coverage of 118 ng cm(-2) was obtained after a 3 h exposure period, indicating that good surface coverage was achieved. Cyclic voltammetry of the ferricyanide redox couple across this SAM modified surface produced similar results to those of a bare electrode; however, the electroreduction of oxygen was found to be impaired. The 4-ATP SAM layer was not stable to repeated electrochemical oxidation and reduction; it is believed that the 4-ATP SAM layer was first converted to a 4'-mercapto-N-phenylquinone diimine (NPQD) layer followed by subsequent formation of a 4'-mercapto-N-phenylquinone monoimine (NPQM) layer. We also report a quartz crystal microbalance study of the attachment of platinum nanoparticles to such SAM modified electrodes. We show that five times the amount of platinum nanoparticles can be attached to a 4-ATP modified electrode surface (observed frequency change - 187 Hz) compared with an NPQD modified electrode surface (observed frequency change -35 Hz). The presence of the platinum particles was confirmed electrochemically by their surface electrochemical properties, which were different from those of the underlying gold electrode. It is believed that this is the first time that such direct evidence of electrochemical communication between platinum nanoparticles and a SAM modified electrode surface has been obtained. It was also shown to be possible to build up multilayer SAM/nanoparticle modified surfaces while maintaining efficient electrochemical communication. Up to three SAM/nanoparticle sandwich layers were constructed.