Desenvolvimento de um sistema de planejamento, gestão de serviços e controle de custos em obras de construção civil

The increasing competitiveness of the construction industry, set in an economic environment in which the offer is now greater than the demand , causes the prices of many products and services, are strongly influenced by the processes of production and the final consumer. Thus, to become more competitive in the market and construction companies are seeking new alternatives to reduce and control costs, production processes and tools that allow for close monitoring of the construction schedule, with the consequent compliance deadline with the client. Based on this scenario, the creation of control tools, service management and planning work emerges as an investment opportunity and an area that can promote great benefits to construction companies. The goal of this work is to present a system of planning, service management and costs control that through worksheets provide information relating to the production phase of the work, allowing the visualization of possible irregularities in the planning and cost of the enterprise, enabling the company to take steps to achieve the goals of the enterprise in question, and correct them when necessary. The developed system has been used in a piece of real estate in Rio Grande do Norte, and the results showed that its use together allowed the construction company to accompany their results and take corrective and preventive actions during the production process, efficiently and effective

Redução do nível protéico da dieta, através da formulação baseada em aminoácidos digestíveis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sistema de gestão ambiental na produção de água mineral

It s more and more evident the subject of the shortage of water, worsened by the accelerated urbanization, growth of the population, increase of the demand and of the costs of its treatment, factors that are also tied up to the increase of the consumption of mineral waters, whose chemical composition or physical-chemistries characteristics do with that are considered beneficial to the health. The growth accelerated all over the world in its consumption aims the concern with the waters quality, the health and the incentive to the consumption of natural products. However, in spite of quite valuable, that resource is explored, most of the time, without optimization of production or actions that avoid wastefulness. This research is justified for the need of minimizing the negative environmental impacts caused by the mineral water s production, mainly in what it say about the generation of effluents and wastes in the productive process, through the study, development and application of cleaner production tools for the environmental management, pertinent for that section. The applicability of Environmental Management System was determined by means of the characterization of the environmental aspects of productive process in a company of the section, in the state of Rio Grande do Norte and of the discussion of the panoramas that demonstrate the tendency for a sustainable development. Actions as a reforestation, optimization of energy and water uses, recycle of solid residues and water reuse were applied during the research, resulting in the considerable reduction of wastes of raw materials and inputs and consequent environmental and economic won. A specific methodology was proposed with concepts of Environmental Management, integrating with Quality Management. As foundations for the elaboration of the methodology, it was realized a similarity analysis among the systems and, mainly, an analysis of the experiences observed in the case study, including specificities, needs and difficulties of the company. With these results, the implantation of a EMS as a company strategy has environmental, economic and social benefits, and this research can be applied and adequate to others companies and sectors

Experimentação, inovação cultura oganizacional: estudo de caso em uma indústria

A experimentação industrial é um método científico de aprendizagem que visa aprimorar conhecimentos sobre o funcionamento de sistemas, almejando redução de variabilidade e incertezas nos processos produtivos. Em inovação, constitui-se como uma oportunidade de teste e pré-implementação, permitindo à empresa aperfeiçoar seus projetos de inovação antes de levá-los ao mercado. Contudo, para que empresas obtenham sucesso em inovar, faz-se necessário um ambiente favorável à inovação, considerando que a cultura organizacional impacta diretamente no potencial inovador. Uma cultura de inovação bem desenvolvida demanda o envolvimento de todos os líderes da empresa atuando como facilitadores do processo. Nesse contexto, esta pesquisa tem como propósito avaliar o perfil da cultura organizacional visando o uso de experimentação no processo de inovação em uma indústria do ramo alimentício no Estado do Rio Grande do Norte. Para tanto, busca-se, por meio de fundamentação teórica, ampliar a compreensão da relação existente entre os temas experimentação, inovação e cultura organizacional, e tem-se como método de pesquisa, uma abordagem quanti-qualitativa em um estudo de caso. Os dados para análise da pesquisa são coletados por meio de entrevistas e aplicação de questionários. Para avaliar a cultura organizacional, utiliza-se como instrumento o questionário baseado no Modelo de Valores Competitivos, desenvolvido por Cameron e Quinn (2006), aplicado com os líderes na empresa em estudo. Este instrumento, denominado OCAI (em inglês Organizacional Culture Assessment Instrument), permite diagnosticar o perfil da cultura organizacional e da cultura da qualidade no cenário atual e no contexto ideal, a partir da percepção dos líderes da organização. Para análise dos dados, utiliza-se a técnica de análise de agrupamento, que permite avaliar a homogeneidade das opiniões dos líderes. Os resultados apontam, conforme a visão dos líderes, a necessidade de mudança no perfil cultural organizacional da empresa em estudo, de uma cultura em que predominam elementos da cultura de mercado (cenário atual) para uma cultura com maior ênfase em elementos da cultura clã e inovadora (cenário ideal), bem como uma cultura de qualidade que estimule a inovação, favorável à geração de ideia e conhecimento, a melhoria contínua e a busca por soluções criativas

Multi-resolução com fóvea móvel para redução e abstração de dados em tempo real

We propose a new approach to reduction and abstraction of visual information for robotics vision applications. Basically, we propose to use a multi-resolution representation in combination with a moving fovea for reducing the amount of information from an image. We introduce the mathematical formalization of the moving fovea approach and mapping functions that help to use this model. Two indexes (resolution and cost) are proposed that can be useful to choose the proposed model variables. With this new theoretical approach, it is possible to apply several filters, to calculate disparity and to obtain motion analysis in real time (less than 33ms to process an image pair at a notebook AMD Turion Dual Core 2GHz). As the main result, most of time, the moving fovea allows the robot not to perform physical motion of its robotics devices to keep a possible region of interest visible in both images. We validate the proposed model with experimental results

Demanda energética na subsolagem realizada antes e depois de diferentes sistemas de preparo periódico do solo

A subsolagem é uma das operações mecanizadas de elevado custo e demanda energética por área, tradicionalmente utilizada pelos agricultores antes do preparo do solo na descompactação de camadas adensadas. Este trabalho teve como objetivo avaliar a demanda energética na operação de subsolagem realizada antes e depois de diferentes sistemas de preparo periódico num solo classificado como Nitossolo Vermelho Distroférrico. Os sistemas de preparo periódico foram: aração com discos; aração com discos mais uma gradagem de nivelamento; grade aradora; grade aradora mais gradagem de nivelamento e escarificação. O trator utilizado como fonte de potência no experimento foi um Valmet 128 (4x2tda). A demanda energética por área foi menor na subsolagem realizada depois do preparo periódico do solo, proporcionando uma economia de 21,9%. A realização da subsolagem depois do preparo periódico do solo resultou numa diminuição da exigência de força de tração em 21,1% e da potência disponível na barra de tração em 15%.

Demanda energética nas operações mecanizadas na silagem de milho no sistema de silo bag

Foi avaliado o consumo energético das operações mecanizadas envolvidas na produção de silagem de planta inteira e silagem de grão úmido de milho, tendo como referência o processamento seco desse cereal. O ensaio foi conduzido na Fazenda Experimental Lageado, pertencente à Faculdade de Ciências Agronômicas, e nas instalações da Faculdade de Medicina Veterinária e Zootecnia - UNESP, localizada no município de Botucatu - SP. O delineamento experimental foi em blocos ao acaso, com parcelas subdivididas no tempo (três épocas de colheita: silagem de planta inteira, silagem de grão úmido e colheita de grãos secos), com 10 repetições. As análises estatísticas foram realizadas por meio do programa ESTAT, pelo teste de média de Tukey, a 5% de probabilidade. A silagem de planta inteira teve o maior consumo de combustível por área. A secagem dos grãos de 15,5% para 13% foi responsável por 87% do gasto de energia por área. A silagem de grão úmido demandou o menor uso de energia por área nas operações mecanizadas.

Estudo da demanda energética e desagregação do solo em diferentes sequências operacionais de preparo periódico

The correct selection of the operational sequence of soil tillage is essential to reduce the cost of agricultural mechanization in the regions that mobilize intensively the soil. The objective of this work was to evaluate the energetic demand and disaggregation of the soil in different operational sequences of subsoiling and systems of periodic soil tillage. The experimental design was blocks at random, in a factorial model 5 x 2 with 5 replications, being 5 tillage systems (D - Disc plow, Dn - disc plow followed at leveler rail, G - weight rail, Gn - weight rail followed of leveler rail and E - Stirrer.) and two sequencies of subsoiling (SP - Subsoiling - tillage and PS - Tillage - subsoiling). There were evaluated the energetic demand, fuel consumption by area and the soil disaggregation. The results showed that the operational sequence tillage of the soil subsoiling (PS) had a lower energetic requirement, except for the stirrer, the sequence tillage the soil - subsoiling consumed less fuel and soil disaggregation didn't show statistic variation.

Demanda energética em diferentes sistemas de preparo periódico do solo antes e depois da subsolagem

Both the inadequate use and the ignorance of the different soil tillage implements available in the home market has become one of the leading motives of failures, related to soil and water conservation. The periodical tillage is traditionally utilized after subsoiling for soil clod breaking, leveling and residue incorporation. This work aimed to evaluate the energy requirement for different periodical soil tillage systems performed before and after subsoiling in a soil classified as Distroferric Red Nitosol. The periodic tillage systems were: disk plowing; disk plowing plus one leveling harrowing; disk harrow; disk harrow plus leveling harrowing stirring. The experimental design was a 5x2 factorial scheme with 5 completely randomized blocks. The results show that the periodic soil preparation systems based on disks have better energy efficiency when performed before the operation of subsoiling. The system of soil preparation with harrowing obtained the lower energy demand, in relation to other periodic soil preparation systems, when done after subsoiling.

Estimação da demanda de instalações elétricas de edificações com múltiplas unidades de consumo

This work aims to predict the total maximum demand of a transformer that will be used in power systems to attend a Multiple Unit Consumption (MUC) in design. In 1987, COSERN noted that calculation of maximum total demand for a building should be different from that which defines the scaling of the input protection extension in order to not overestimate the power of the transformer. Since then there have been many changes, both in consumption habits of the population, as in electrical appliances, so that this work will endeavor to improve the estimation of peak demand. For the survey, data were collected for identification and electrical projects in different MUCs located in Natal. In some of them, measurements were made of demand for 7 consecutive days and adjusted for an integration interval of 30 minutes. The estimation of the maximum demand was made through mathematical models that calculate the desired response from a set of information previously known of MUCs. The models tested were simple linear regressions, multiple linear regressions and artificial neural networks. The various calculated results over the study were compared, and ultimately, the best answer found was put into comparison with the previously proposed model

Extração e Representação de Conhecimento de Séries Temporais de Demanda de Energia Elétrica Usando TSKR

The opening of the Brazilian market of electricity and competitiveness between companies in the energy sector make the search for useful information and tools that will assist in decision making activities, increase by the concessionaires. An important source of knowledge for these utilities is the time series of energy demand. The identification of behavior patterns and description of events become important for the planning execution, seeking improvements in service quality and financial benefits. This dissertation presents a methodology based on mining and representation tools of time series, in order to extract knowledge that relate series of electricity demand in various substations connected of a electric utility. The method exploits the relationship of duration, coincidence and partial order of events in multi-dimensionals time series. To represent the knowledge is used the language proposed by Mörchen (2005) called Time Series Knowledge Representation (TSKR). We conducted a case study using time series of energy demand of 8 substations interconnected by a ring system, which feeds the metropolitan area of Goiânia-GO, provided by CELG (Companhia Energética de Goiás), responsible for the service of power distribution in the state of Goiás (Brazil). Using the proposed methodology were extracted three levels of knowledge that describe the behavior of the system studied, representing clearly the system dynamics, becoming a tool to assist planning activities

Laminados compósitos de PRFV: efeitos da descontinuidade geométrica e do envelhecimento ambiental acelerado

The growing demand in the use of composite materials necessitates a better understanding of its behavior related to many conditions of loading and service, as well as under several ways of connections involved in mechanisms of structural projects. Within these project conditions are highlighted the presence of geometrical discontinuities in the area of cross and longitudinal sections of structural elements and environmental conditions of work like UV radiation, moisture, heat, leading to a decrease in final mechanical response of the material. In this sense, this thesis aims to develop studies detailed (experimental and semi-empirical models) the effects caused by the presence of geometric discontinuity, more specifically, a central hole in the longitudinal section (with reduced cross section) and the influence of accelerated environmental aging on the mechanical properties and fracture mechanism of FGRP composite laminates under the action of uniaxial tensile loads. Studies on morphological behavior and structural degradation of composite laminates are performed by macroscopic and microscopic analysis of affected surfaces, in addition to evaluation by the Measurement technique for mass variation (TMVM). The accelerated environmental aging conditions are simulated by aging chamber. To study the simultaneous influence of aging/geometric discontinuity in the mechanical properties of composite laminates, a semiempirical model is proposed and called IE/FCPM Model. For the stress concentration due to the central hole, an analisys by failures criteria were performed by Average-Stress Criterion (ASC) and Point-Stress Criterion (PSC). Two polymeric composite laminates, manufactured industrially were studied: the first is only reinforced by short mats of fiberglass-E (LM) and the second where the reinforced by glass fiber/E comes in the form of bidirectional fabric (LT). In the conception configurations of laminates the anisotropy is crucial to the final mechanical response of the same. Finally, a comparative study of all parameters was performed for a better understanding of the results. How conclusive study, the characteristics of the final fracture of the laminate under all conditions that they were subjected, were analyzed. These analyzes were made at the macroscopic level (scanner) microscope (optical and scanning electron). At the end of the analyzes, it was observed that the degradation process occurs similarly for each composite researched, however, the LM composite compared to composite LT (configurations LT 0/90º and LT ±45º) proved to be more susceptible to loss of mechanical properties in both regarding with the central hole as well to accelerated environmental aging

Obtenção de pós de Nb a partir da redução aluminotérmica com ignição por plasma

The aluminothermic reduction consists in an exothermic reaction between a metallic oxide and aluminum to produce the metal and the scum. The extracted melted metal of that reaction usually comes mixed with particles of Al2O3 resulting of the reduction, needing of subsequent refine to eliminate the residual impure as well as to eliminate porosities. Seeking to obtain a product in powder form with nanometric size or even submicrometric, the conventional heat source of the reaction aluminothermic , where a resistor is used (ignitor) as ignition source was substituted, for the plasma, that acts more efficient way in each particle of the sample. In that work it was used as metallic oxide the niobium pentoxide (Nb2O5) for the exothermal reaction Nb2O5 + Al. Amounts stoichiometric, substoichiometric and superestoichiometric of aluminum were used. The Nb2O5 powder was mixed with aluminum powder and milled in planetarium of high energy for a period of 6 hours. Those powders were immerged in plasm that acts in a punctual way in each particle, transfering heat, so that the reaction can be initiate and spread integrally for the whole volume of the particle. The mixture of Nb2O5 + Al was characterized through the particle size analysis by laser and X-ray diffraction (DRX) and the obtained product of reaction was characterized using the electronic microscopy of sweeping (MEV) and the formed phases were analyzed by DRX. Niobium powders with inferior sizes to 1 mm were obtained by that method. It is noticed, through the analysis of the obtained results, that is possible to accomplish the aluminothermic reduction process by plasma ignition with final particles with inferior sizes to the original oxide

Redução carbotérmica de TiO2 por descarga em cátodo oco

In this study we used the plasma as a source of energy in the process of carbothermic reduction of rutile ore (TiO2). The rutile and graphite powders were milled for 15 h and placed in a hollow cathode discharge produced by in order to obtain titanium carbonitride directly from the reaction, was verified the influence of processing parameters of plasma temperature and time in the synthesis of TiCN. The reaction was carried out at 600, 700 and 800˚C for 3 to 4 hours in an atmosphere of nitrogen and argon. During all reactions was monitored by plasma technique of optical emission spectroscopy (EEO) to check the active species present in the process of carbothermal reduction of TiO2. The powder obtained after the reactions were characterized by the techniques of X-ray diffraction (XRD) and scanning electron microscopy (SEM). The technique of EEO were detected in all reactions the spectra CO and NO, and these gas-phase resulting from the reduction of TiO2. The results of X-ray diffraction confirmed the reduction, where for all conditions studied there was evidence of early reduction of TiO2 through the emergence of intermediate oxides. In the samples reduced at 600 and 700˚C, there was only the phase Ti6O11, those reduced to 800˚C appeared Ti5O9 phases, and Ti6O11 Ti7O13, confirming that the carbothermal reduction in plasma, a reduction of the ore rutile (TiO2) in a series of intermediate titanium oxide (TinO2n-1) where n varies between 5 and 10

Compósito Polimérico Híbrido: Comportamento Mecãnico, Descotinuidade Geométrica e Resistência Residual

The growing demand in the use of hybrid composite materials makes it essential a better understanding of their behavior face of various design conditions, such as the presence of geometric discontinuities in the cross section of structural elements. This way, the purpose of this dissertation is a study of the mechanical response (strength and stiffness), modes (characteristics) of fracture and Residual Strength of an hybrid polymeric composite with and without a geometric discontinuity in its longitudinal section (with a reduction in the cross section) loaded by uniaxial tension. This geometric discontinuity is characterized by central holes of different diameters. The hybrid composite was fabricated as laminate (plate) and consisting of ortho-tereftalic polyester matrix reinforced by 04 outer layers of Jute fibers bidirectional fabrics and 01 central layer of E-glass bidirectional fabric. The laminate was industrially manufactured (Tecniplas Nordeste Indústria e Comércio Ltda.), obtained by the hand lay-up technique. Initially, a study of the volumetric density of the laminate was made in order to verify its use in lightweight structures. Also were performed comparative studies on the mechanical properties and fracture modes under the conditions of the specimens without the central hole and with the different holes. For evaluating the possible influence of the holes in the structural stability of the laminate, the Residual Strength of the composite was determined for each case of variation in hole diameter. As a complementary study, analyses of the macroscopic final fracture characteristic of the laminates were developed. The presence of the central hole of any sizes, negatively changed the ultimate tensile strength. Regarding the elastic modulus, moreover, the difference found between the specimens was within the range of tests displacement, showing the laminate stability related to the stiffness