Global analysis of aerodynamics deflectors efficiency in the grinding process

The conventional, grinding methods in some cases are not very efficient because the arising of thermal damages in the pieces is very common. Optimization methods of cutting fluid application in the grinding zone are essential to prevent thermal problems from interaction of the wheel grains with the workpiece. surface. The optimization can happen through the correct selection of the cut parameters and development of devices that eliminate air layer effects generated around the grinding wheel. This article will collaborate with the development of an experimentation methodology which allows evaluating, comparatively, the performance of the deflectors in the cutting region to minimize the air layer effect of the high speed of the grinding wheel. The air layers make the cutting fluid jet to dissipate in the machine. An optimized nozzle was used in order to compare the results with the conventional method (without baffles or deflectors) of cutting fluid application. The results showed the high eficciency of the deflectors or baffles in the finish results. Copyright © 2006 by ABCM.

Baseline and stress-induced plasma corticosterone concentrations of mice selectively bred for high voluntary wheel running

The hypothalamic-pituitary-adrenal (HPA) axis is important in regulating energy metabolism and in mediating responses to stressors, including increasing energy availability during physical exercise. In addition, glucocorticoids act directly on the central nervous system and influence behavior, including locomotor activity. To explore potential changes in the HPA axis as animals evolve higher voluntary activity levels, we characterized plasma corticosterone (CORT) concentrations and adrenal mass in four replicate lines of house mice that had been selectively bred for high voluntary wheel running (HR lines) for 34 generations and in four nonselected control (C) lines. We determined CORT concentrations under baseline conditions and immediately after exposure to a novel stressor (40 min of physical restraint) in mice that were housed without access to wheels. Resting daytime CORT concentrations were approximately twice as high in HR as in C mice for both sexes. Physical restraint increased CORT to similar concentrations in HR and C mice; consequently, the proportional response to restraint was smaller in HR than in C animals. Adrenal mass did not significantly differ between HR and C mice. Females had significantly higher baseline and postrestraint CORT concentrations and significantly larger adrenal glands than males in both HR and C lines. Replicate lines showed significant variation in body mass, length, baseline CORT concentrations, and postrestraint CORT concentrations in one or both sexes. Among lines, both body mass and length were significantly negatively correlated with baseline CORT concentrations, suggesting that CORT suppresses growth. Our results suggest that selection for increased locomotor activity has caused correlated changes in the HPA axis, resulting in higher baseline CORT concentrations and, possibly, reduced stress responsiveness and a lower growth rate. © 2007 by The University of Chicago. All rights reserved.

Few substitutions affect the bioluminescence spectra of Phrixotrix (Coleoptera: Phengodidae) luciferases: a site-directed mutagenesis survey

Phrixotrix (railroad worm) luciferases produce bioluminescence in the green and red regions of the spectrum, depending on the location of the lanterns, and are the only luciferases naturally producing red bioluminescence. Comparison of the luciferase sequences showed a set of substitutions that could be involved in bioluminescence colour determination: (a) unique substitutions in the red luciferase replacing otherwise invariant residues; (b) conserved basic residues in the green-yellow emitting luciferases; and (c) an additional R353 residue in red-emitting luciferase (Viviani et al., 1999). To investigate whether these sites have a functional role in bioluminescence colour determination, we performed a site-directed mutagenesis. Natural substitutions in the region 220-344 and residues in the putative luciferin-binding site were also investigated. With the exception of the previously identified substitution of R215 and T226 (Viviani et al., 2002), which display dramatic red-shift effects on the spectrum of green-yellow-emitting luciferases, only a few substitutions had a moderate effect on the spectrum of the green-emitting luciferase. In contrast, no single substitution affected the spectrum of the red-emitting luciferase. The results suggest that the identity of the active site residues is not so critical for determining red bioluminescence in PxRE luciferase. Rather, the conformation assumed during the emitting step could be critical to set up proper interactions with excited oxyluciferin. Copyright ©2007 John Wiley & Sons, Ltd.

Para além do Rio Grande: Os impactos da economia paulista sobre O Triângulo Mineiro

In this work our intention was to investigate the impact of Sao Paulo's coffee economy on the Minas Gerais Triangle Region, during its penetration into the area because of the extension of the Mogiana Railroad Company in 1889. We attempt to understand the impact caused along this coffee railroad in a region where this product almost did not exist, and the changes that occurred to the economic panorama of the region. Furthermore we have taken as an example, the city of Uberaba, the most important, in this region at that time.

Glycogen storage and muscle glucose transporters (GLUT-4) of mice selectively bred for high voluntary wheel running

To examine the evolution of endurance-exercise behaviour, we have selectively bred four replicate lines of laboratory mice (Mus domesticus) for high voluntary wheel running ('high runner' or HR lines), while also maintaining four non-selected control (C) lines. By generation 16, HR mice ran ∼2.7-fold more than C mice, mainly by running faster (especially in females), a differential maintained through subsequent generations, suggesting an evolutionary limit of unknown origin. We hypothesized that HR mice would have higher glycogen levels before nightly running, show greater depletion of those depots during their more intense wheel running, and have increased glycogen synthase activity and GLUT-4 protein in skeletal muscle. We sampled females from generation 35 at three times (photophase 07:00 h-19:00 h) during days 5-6 of wheel access, as in the routine selection protocol: Group 1, day 5, 16:00 h-17:30 h, wheels blocked from 13:00 h; Group 2, day 6, 02:00 h-03:30 h (immediately after peak running); and Group 3, day 6, 07:00 h-08:30 h. An additional Group 4, sampled 16:00 h-17:30 h, never had wheels. HR individuals with the mini-muscle phenotype (50% reduced hindlimb muscle mass) were distinguished for statistical analyses comparing C, HR normal, and HR mini. HR mini ran more than HR normal, and at higher speeds, which might explain why they have been favored by the selective-breeding protocol. Plasma glucose was higher in Group 1 than in Group 4, indicating a training effect (phenotypic plasticity). Without wheels, no differences in gastrocnemius GLUT-4 were observed. After 5 days with wheels, all mice showed elevated GLUT-4, but HR normal and mini were 2.5-fold higher than C. At all times and irrespective of wheel access, HR mini showed approximately three-fold higher [glycogen] in gastrocnemius and altered glycogen synthase activity. HR mini also showed elevated glycogen in soleus when sampled during peak running. All mice showed some glycogen depletion during nightly wheel running, in muscles and/or liver, but the magnitude of this depletion was not large and hence does not seem to be limiting to the evolution of even-higher wheel running.

Finishing of flat parts led by lapping kinematics on abrasive disc dressed in agreement with overlap factors

This paper discusses the investigation of an abrasive process for finishing flat workpieces, based on the combination of important grinding and lapping characteristics. Instead of loose abrasive grains between the workpiece and the lapping plate, a resinoid grinding wheel of hot-pressed silicon carbide is placed on the plate of a device resembling a lapping machine. The resin bond grinding wheel is dressed with a single-point diamond. In addition to keeping the plate flat, dressing also plays the role of interfering in the behavior of the process by varying the overlap factor (Ud). It was found that the studied process simplify the set-up and can be controlled more easily than in lapping, whose is a painstaking process. The surface roughness and flatness deviation proved comparable to those of lapping, or even finer than it, with the additional advantage of a less contaminated workpiece surface with a shiny appearance. The process was also monitored by acoustic emission (AE), which indicates to be a promissing and suitable technique for use in this process. Copyright © 2008 by ASME.

Análise geoambiental da região de marília, SP: Suscetibilidade a processos erosivos frente ao histórico de ocupação da área

The study area comprises the western portion of the Marília Plateau, State of São Paulo, southeastern Brazil. The geological substrate encompasses Cretaceous sedimentary rocks of the Bauru Group and local Neocenozoic units like colluvium aprons, fluvial terrace deposits, in situ regoliths, and modern alluvial deposits. In a geomorphologic sense, the study area might be characterized as showing two main pediplanes, viz. P1 Surface (upper) and P2 Surface (lower), both surfaces are presently under dissecation processes. After the 1920's the expansion of the railroad system fostered the removal of the natural vegetation, which in turn was followed by the introduction of coffee, peanut, corn and cotton crops. This intense exploitation was conducted without respect to the soil carrying capacity and its natural susceptibility to erosional processes, including an aggressive form known as voçoroca. As a result, the study shows that the most susceptible material includes colluvium aprons, in situ regoliths, and colluvium-alluvium or alluvium deposits. The most critical situation is in the P2 Surface context, near the bottom of the Marília Plateau scarpment, where surface runoff can be very strong. Another point of active erosion is represented by the exposed walls of gullies and voçorocas, mainly in fluvial reaches subjected to talweg lowering. In a general sense, this study shows current evidence of erosional stability due to the ìntroduction of pastures as a predominant type of land occupation and to a series of erosion control procedures. Among these actions are terrace implantation, construction of small pits for runoff control, natural or induced reforestation by land owners. Despite these efforts, some erosion points remain chiefly in steeper country roads and trail stretches, in areas of concentration of cattle tracks (e.g., near cattle ponds), gullies or voçorocas exposed walls, and badly planned urbanization. The permanence of these erosion points demonstrates the necessity of a continuous monitoring of surface dynamics as well as a rapid and effective intervining measures of erosion and/or silting control.

Avaliação preliminar do potencial turístico do município de rifaina (SP) e os impactos decorrentes do uso público de seus atrativos paisagísticos

This paper attempts to assess both the touristic potential of scenic attractions and the environmental impacts resulting from the public use of such attractions in the Rifaina Municipality, State of São Paulo, Southeastern Brazil. In the recent past, this municipality had its economy concentrated in rural activities (livestock, corn, rice and bean crops) and in the ceramic industry (production of bricks, tiles and shackles),which was largely developed in the floodplain of the Rio Grande before the construction of the Jaguara Power Plant Dam. The impacts resulting from touristic activities were evaluated by applying the VIM - Visitor Impact Management method, with emphasis on biophysical indicators. The main touristic attractions analyzed were: (1) Rifaina artificial beach; (2) Jaguara Reservoir; (3) Morro do Chapéu (scenic hill); (4) Touristic railroad; and (5) Cuestas cliffs. Attractions (1) and (2) are the most exploited ones, including, in the second case, nautical sports, sportive and craft fishing, and summer lodging. Although currently disabled, the touristic railroad presents potential conditions to be re-explored. Attractions (3) and (5), despite keeping high landscape and ecological ecotouristic potential, are the least visited places. In the present paper, a preliminary characterization of the major issues of tourism industry in the Rifaina municipality is made, including suggestions for the sustainable exploitation of tourism resources. The final results of the environmental impact evaluation of the tourism activities include small impacts in attractions (4) and (5) and moderate impacts to the three first attractions. In order to keep the sustainable touristic potential for that municipality this study proposes the improvement of the following measures: to foster research projects on technical or scientific aspects of the touristic attractions, improvement of tourism infrastructure and the creation of an Environmental Protection Area (APA) of the cuestas' scarps.

Influência das técnicas de mínima quantidade de lubrificante, refrigeração otimizada e refrigeração convencional na qualidade de peças produzidas com aços endurecidos no processo de retificação

The influence of minimum lubrication, optimized and conventional cooling at different flows and application rates of cutting fluids on the quality of hardened-steel pieces produced by external cylindrical plunge grinding with super-abrasive grinding wheels with low CBN concentrations was verified. The analysis of the quality of the pieces was performed through the assessment of the behavior of the specific energy of the grinding, roughness, roundness deviation, and the generated residual stress. By analyzing of the application ways and of the several flows and application rates of the cutting fluid, one could encounter lubrication/cooling conditions that enable the reduction in cutting fluid volume, reduction in grinding time without compromising the dimensional parameters (superficial finishing, surface integrity). Regarding the different applications of cutting fluids, it could be noted the optimized application for higher velocities has presented the best performance, demonstrating the effectiveness of the new concept of nozzle utilized.

Uso do AHP na avaliação do desempenho do sistema de gestão da qualidade, meio ambiente e segurança e saúde ocupacional integrados

The paper analyses the application of the AHP method together with the attach A of ISO 9004:2000 in order to evaluate the performance of two industrial organizations, both possessing quality management systems with ISO 9001:2000 certifications, based on the specific requirements of quality, environment, occupational health and management systems. The evaluated organizations were a government-owned company from the science and technology sector that works in the nuclear area, and a private company that works in the automotive and railroad area. The open software Web-Hipre version 1.22 from Helsinki University of Technology, Finland, was used. The results demonstrated that the AHP method together with the attach A of ISO 9004:2000 is adequate to evaluate organizational performances. Both organizations presented similar performance levels.

Networked control system for the guidance of a four-wheel steering agricultural robotic platform

A current trend in the agricultural area is the development of mobile robots and autonomous vehicles for precision agriculture (PA). One of the major challenges in the design of these robots is the development of the electronic architecture for the control of the devices. In a joint project among research institutions and a private company in Brazil a multifunctional robotic platform for information acquisition in PA is being designed. This platform has as main characteristics four-wheel propulsion and independent steering, adjustable width, span of 1,80m in height, diesel engine, hydraulic system, and a CAN-based networked control system (NCS). This paper presents a NCS solution for the platform guidance by the four-wheel hydraulic steering distributed control. The control strategy, centered on the robot manipulators control theory, is based on the difference between the desired and actual position and considering the angular speed of the wheels. The results demonstrate that the NCS was simple and efficient, providing suitable steering performance for the platform guidance. Even though the simplicity of the NCS solution developed, it also overcame some verified control challenges in the robot guidance system design such as the hydraulic system delay, nonlinearities in the steering actuators, and inertia in the steering system due the friction of different terrains. Copyright © 2012 Eduardo Pacincia Godoy et al.

Influence of optimized lubrication-cooling and minimum quantity lubrication on the cutting forces, on the geometric quality of the surfaces and on the micro-structural integrity of hardened steel parts

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estimating hardness of eucalyptus wood with a portable hardness tester

More than 80% of the 29600 km of the Brazilian railroad mesh employs wooden sleepers. The problem of hard availability of native wood for this purpose leads to the alternative use of reforestation species to produce sleepers. Considering the great difficulty to, in field condition, evaluate characteristics that are of major importance to define its suitability to sleeper production the Research Group on Forest Products from FCA/UNESP - Brazil had developed equipment for field evaluation of hardness in wood - Portable Hardness Tester. This paper reports the functional validation tests, performed with different species of Eucalyptus. Results revealed the equipment great functionality, easy-to-use characteristics and applicability to Eucalyptus wood. Moderate to strong relationships between laboratory and validated values of hardness were found. The best validation model was obtained using the data provided by the experimental dispositive 3 (R2=0.74 and SSE= 7.71 kJ/m2) while the experimental dispositive 1 gave the worse validation (R2=0.55 and SSE= 13.46 kJ/m2).

Application of MLP and Kohonen networks for recognition of wear patterns of single-point dressers

Grinding is a parts finishing process for advanced products and surfaces. However, continuous friction between the workpiece and the grinding wheel causes the latter to lose its sharpness, thus impairing the grinding results. This is when the dressing process is required, which consists of sharpening the worn grains of the grinding wheel. The dressing conditions strongly affect the performance of the grinding operation; hence, monitoring them throughout the process can increase its efficiency. The objective of this study was to estimate the wear of a single-point dresser using intelligent systems whose inputs were obtained by the digital processing of acoustic emission signals. Two intelligent systems, the multilayer perceptron and the Kohonen neural network, were compared in terms of their classifying ability. The harmonic content of the acoustic emission signal was found to be influenced by the condition of dresser, and when used to feed the neural networks it is possible to classify the condition of the tool under study.

Neural networks models for wear patterns recognition of single-point dresser

Grinding is a workpiece finishing process for advanced products and surfaces. However, the constant friction between workpiece and grinding wheel causes the latter to lose its sharpness, thereby impairing the result of the grinding process. When this occurs, the dressing process is essential to sharpen the worn grains of the grinding wheel. The dressing conditions strongly influence the performance of the grinding operation; hence, monitoring them throughout the process can increase its efficiency. The purpose of this study was to classify the wear condition of a single-point dresser using intelligent systems whose inputs were obtained by digitally processing acoustic emission signals. Two multilayer perceptron (MLP) neural networks were compared for their classification ability, one using the root mean square (RMS) statistics and another the ratio of power (ROP) statistics as input. In this study, it was found that the harmonic content of the acoustic emission signal is influenced by the condition of the dresser, and that the condition of the tool under study can be classified by using the aforementioned statistics to feed a neural network. © IFAC.