Lithography-free micro- and nanostructuring based on conventional plasma etching

In now-a-days semiconductor and MEMS technologies the photolithography is the working horse for fabrication of functional devices. The conventional way (so called Top-Down approach) of microstructuring starts with photolithography, followed by patterning the structures using etching, especially dry etching. The requirements for smaller and hence faster devices lead to decrease of the feature size to the range of several nanometers. However, the production of devices in this scale range needs photolithography equipment, which must overcome the diffraction limit. Therefore, new photolithography techniques have been recently developed, but they are rather expensive and restricted to plane surfaces. Recently a new route has been presented - so-called Bottom-Up approach - where from a single atom or a molecule it is possible to obtain functional devices. This creates new field - Nanotechnology - where one speaks about structures with dimensions 1 - 100 nm, and which has the possibility to replace the conventional photolithography concerning its integral part - the self-assembly. However, this technique requires additional and special equipment and therefore is not yet widely applicable. This work presents a general scheme for the fabrication of silicon and silicon dioxide structures with lateral dimensions of less than 100 nm that avoids high-resolution photolithography processes. For the self-aligned formation of extremely small openings in silicon dioxide layers at in depth sharpened surface structures, the angle dependent etching rate distribution of silicon dioxide against plasma etching with a fluorocarbon gas (CHF3) was exploited. Subsequent anisotropic plasma etching of the silicon substrate material through the perforated silicon dioxide masking layer results in high aspect ratio trenches of approximately the same lateral dimensions. The latter can be reduced and precisely adjusted between 0 and 200 nm by thermal oxidation of the silicon structures owing to the volume expansion of silicon during the oxidation. On the basis of this a technology for the fabrication of SNOM calibration standards is presented. Additionally so-formed trenches were used as a template for CVD deposition of diamond resulting in high aspect ratio diamond knife. A lithography-free method for production of periodic and nonperiodic surface structures using the angular dependence of the etching rate is also presented. It combines the self-assembly of masking particles with the conventional plasma etching techniques known from microelectromechanical system technology. The method is generally applicable to bulk as well as layered materials. In this work, layers of glass spheres of different diameters were assembled on the sample surface forming a mask against plasma etching. Silicon surface structures with periodicity of 500 nm and feature dimensions of 20 nm were produced in this way. Thermal oxidation of the so structured silicon substrate offers the capability to vary the fill factor of the periodic structure owing to the volume expansion during oxidation but also to define silicon dioxide surface structures by selective plasma etching. Similar structures can be simply obtained by structuring silicon dioxide layers on silicon. The method offers a simple route for bridging the Nano- and Microtechnology and moreover, an uncomplicated way for photonic crystal fabrication.

Micro-electromechanical structural design and optimization of vertical cavity photonic devices with wide continuous tuning

Diese Arbeit umfa��t das elektromechanische Design und die Designoptimierung von weit durchstimmbaren optischen multimembranbasierten Bauelementen, mit vertikal orientierten Kavit��ten, basierend auf der Finiten Element Methode (FEM). Ein multimembran InP/Luft Fabry-P��rot optischer Filter wird dargestellt und umfassend analysiert. In dieser Arbeit wird ein systematisches strukturelles Designverfahren dargestellt. Genaue analytische elektromechanischer Modelle f��r die Bauelemente sind abgeleitet worden. Diese k��nnen unsch��tzbare Werkzeuge sein, um am Anfang der Designphase schnell einen klaren Einblick zur Verf��gung zu stellen. Mittels des FEM Programms ist der durch die nicht-lineare Verspannung hervorgerufene versteifende Effekt nachgeforscht und sein Effekt auf die Verl��ngerung der mechanischen Durchstimmungsstrecke der Bauelemente demonstriert worden. Interessant war auch die Beobachtung, dass die normierte Relation zwischen Ablenkung und Spannung ein unver��nderliches Profil hat. Die Deformation der Membranfl��chen der in dieser Arbeit dargestellten Bauelementformen erwies sich als ein unerw��nschter, jedoch manchmal unvermeidbarer Effekt. Es zeigt sich aber, dass die Wahl der Gr����e der strukturellen Dimensionen den Grad der Membrandeformation im Falle der Aktuation beeinflusst. Diese Arbeit stellt ein elektromechanisches in FEMLAB implementierte quasi-3D Modell, das allgemein f��r die Modellierung d��nner Strukturen angewendet werden kann, dar; und zwar indem man diese als 2D-Objekte betrachtet und die dritte Dimension als eine konstante Gr����e (z.B. die Schichtdicke) oder eine Gr����e, welche eine mathematische Funktion ist, annimmt. Diese Annahme verringert drastisch die Berechnungszeit sowie den erforderlichen Arbeitsspeicherbedarf. Weiter ist es f��r die Nachforschung des Effekts der Skalierung der durchstimmbaren Bauelemente verwendet worden. Eine neuartige Skalierungstechnik wurde abgeleitet und verwendet. Die Ergebnisse belegen, dass das daraus resultierende, skalierte Bauelement fast genau die gleiche mechanische Durchstimmung wie das unskalierte zeigt. Die Einbeziehung des Einflusses von axialen Verspannungen und Gradientenverspannungen in die Berechnungen erforderte die ��nderung der Standardimplementierung des 3D Mechanikberechnungsmodus, der mit der benutzten FEM Software geliefert wurde. Die Ergebnisse dieser Studie zeigen einen gro��en Einfluss der Verspannung auf die Durchstimmungseigenschaften der untersuchten Bauelemente. Ferner stimmten die Ergebnisse der theoretischen Modellrechnung mit den experimentellen Resultaten sehr gut ��berein.

Artificial micro RNA system in Dictyostelium discoideum

Dictyostelium discoideum is a social amoeba that serves as a model system for RNA interference and related mechanisms. Its position between plants and animals enables evolutionary snapshot of mechanisms and protein machinery involved in investigated subjects. MiRNAs are small regulatory RNAs that are evolutionary conserved and present in animals, plants, viruses and some prokaryotes. They have roles in development, cell growth and differentiation, apoptosis and their miss-regulation is associated with many diseases such as cancer, neurodegenerative disorders and diabetes. Recently, through sequencing of DNA libraries miRNAs have been discovered in D. discoideum. In this work, it has been shown that heterologues miRNA let-7 can be expressed and processed in D. discoideum. Expression of let-7 miRNA in social amoeba resulted in a strong developmental phenotype suggesting an overload of the processing/silencing system or/and endogenous targets. The various effects on prel-7 strain have been observed and characterized, serving as a background for postulation of miRNA roles. An artificial miRNA system has been established and imposed to D. discoideum, showing that miRNAs in Dictyostelium could mediate gene expression on the level of mRNA stability and on the posttranscriptional level. Furthermore, presence of translational inhibition as a type of gene control was shown for the first time in this organism. Due to it new structures representing co-localities of miRNA and target mRNA have been detected. Taken together, this work shows functional artificial miRNA system and postulates roles of endogenous small RNA in social amoeba.

Resource use pattern and agroecosystem functioning in Rawanganga micro-watershed in Garhwal Himalaya, India

Agro-ecological resource use pattern in a traditional hill agricultural watershed in Garhwal Himalaya was analysed along an altitudinal transect. Thirty one food crops were found, although only 0.5% agriculture land is under irrigation in the area. Fifteen different tree species within agroforestry systems were located and their density varied from 30-90 trees/ha. Grain yield, fodder from agroforest trees and crop residue were observed to be highest between 1200 and 1600 m a.s.l. Also the annual energy input- output ratio per hectare was highest between 1200 and 1600 m a.s.l. (1.46). This higher input- output ratio between 1200-1600 m a.s.l. was attributed to the fact that green fodder, obtained from agroforestry trees, was considered as farm produce. The energy budget across altitudinal zones revealed 95% contribution of the farmyard manure and the maximum output was in terms of either crop residue (35%) or fodder (55%) from the agroforestry component. Presently on average 23%, 29% and 41% cattle were dependent on stall feeding in villages located at higher, lower and middle altitudes respectively. Similarly, fuel wood consumption was greatly influenced by altitude and family size. The efficiency and sustainability of the hill agroecosystem can be restored by strengthening of the agroforestry component. The approach will be appreciated by the local communities and will readily find their acceptance and can ensure their effective participation in the programme.

Employment and Income of Workers on Indonesian Oil Palm Plantations: Food Crisis at the Micro Level

The importance of oil palm sector for Indonesia is inevitable as the country currently serves as the world���s largest producer of crude palm oil. This paper focuses on the situation of workers on Indonesian oil palm plantations. It attempts to investigate whether the remarkable development of the sector is followed by employment opportunities and income generation for workers. This question is posed within the theoretical framework on the link between trade liberalisation and labour rights, particularly in a labour-intensive and low-skilled sector. Based on extensive field research in Riau, this paper confirms that despite the rapid development of the oil palm plantation sector in Indonesia, the situations of workers in the sector remain deplorable, particularly their employment status and income. This also attests that trade liberalisation in the sector adversely affects labour rights. The poor working conditions also have ramifications for food security at the micro level.

Parallel Coupled Micro-Macro Actuators

This thesis presents a new actuator system consisting of a micro-actuator and a macro-actuator coupled in parallel via a compliant transmission. The system is called the Parallel Coupled Micro-Macro Actuator, or PaCMMA. In this system, the micro-actuator is capable of high bandwidth force control due to its low mass and direct-drive connection to the output shaft. The compliant transmission of the macro-actuator reduces the impedance (stiffness) at the output shaft and increases the dynamic range of force. Performance improvement over single actuator systems was expected in force control, impedance control, force distortion and reduction of transient impact forces. A set of quantitative measures is proposed and the actuator system is evaluated against them: Force Control Bandwidth, Position Bandwidth, Dynamic Range, Impact Force, Impedance ("Backdriveability'"), Force Distortion and Force Performance Space. Several theoretical performance limits are derived from the saturation limits of the system. A control law is proposed and control system performance is compared to the theoretical limits. A prototype testbed was built using permanenent magnet motors and an experimental comparison was performed between this actuator concept and two single actuator systems. The following performance was observed: Force bandwidth of 56Hz, Torque Dynamic Range of 800:1, Peak Torque of 1040mNm, Minimum Torque of 1.3mNm. Peak Impact Force was reduced by an order of magnitude. Distortion at small amplitudes was reduced substantially. Backdriven impedance was reduced by 2-3 orders of magnitude. This actuator system shows promise for manipulator design as well as psychophysical tests of human performance.

Design and Development of 3-DOF Modular Micro Parallel Kinematic Manipulator

This paper presents the research and development of a 3-legged micro Parallel Kinematic Manipulator (PKM) for positioning in micro-machining and assembly operations. The structural characteristics associated with parallel manipulators are evaluated and the PKMs with translational and rotational movements are identified. Based on these identifications, a hybrid 3-UPU (Universal Joint-Prismatic Joint-Universal Joint) parallel manipulator is designed and fabricated. The principles of the operation and modeling of this micro PKM is largely similar to a normal size Stewart Platform (SP). A modular design methodology is introduced for the construction of this micro PKM. Calibration results of this hybrid 3-UPU PKM are discussed in this paper.

Investigation of aspect ratio of hole drilling from micro to nanoscale via focused ion beam fine milling

Holes with different sizes from microscale to nanoscale were directly fabricated by focused ion beam (FIB) milling in this paper. Maximum aspect ratio of the fabricated holes can be 5:1 for the hole with large size with pure FIB milling, 10:1 for gas assistant etching, and 1:1 for the hole with size below 100 nm. A phenomenon of volume swell at the boundary of the hole was observed. The reason maybe due to the dose dependence of the effective sputter yield in low intensity Gaussian beam tail regions and redeposition. Different materials were used to investigate variation of the aspect ratio. The results show that for some special material, such as Ni-Be, the corresponding aspect ratio can reach 13.8:1 with Cl��� assistant etching, but only 0.09:1 for Si(100) with single scan of the FIB.

Micro-layered-photolithography for Micro-Fabrication and Micro-Molding

A novel process based on the principle of layered photolithography has been proposed and tested for making real three-dimensional micro-structures. An experimental setup was designed and built for doing experiments on this micro-fabrication process. An ultraviolet (UV) excimer laser at the wavelength of 248 nm was used as the light source and a single piece of photo-mask carrying a series of two dimensional (2D) patterns sliced from a three dimensional (3D) micro-part was employed for the photolithography process. The experiments were conducted on the solidification of liquid photopolymer from single layer to multiple layers. The single-layer photolithography experiments showed that certain photopolymers could be applied for the 3D micro-fabrication, and solid layers with sharp shapes could be formed from the liquid polymer identified. By using a unique alignment technique, multiple layers of photolithography was successfully realized for a micro-gear with features at 60 microns. Electroforming was also conducted for converting the photopolymer master to a metal cavity of the micro-gear, which proved that the process is feasible for micro-molding.

Process Variability in Micro-Embossing

A promising technique for the large-scale manufacture of micro-fluidic devices and photonic devices is hot embossing of polymers such as PMMA. Micro-embossing is a deformation process where the workpiece material is heated to permit easier material flow and then forced over a planar patterned tool. While there has been considerable, attention paid to process feasibility very little effort has been put into production issues such as process capability and eventual process control. In this paper, we present initial studies aimed at identifying the origins and magnitude of variability for embossing features at the micron scale in PMMA. Test parts with features ranging from 3.5- 630 ��m wide and 0.9 ��m deep were formed. Measurements at this scale proved very difficult, and only atomic force microscopy was able to provide resolution sufficient to identify process variations. It was found that standard deviations of widths at the 3-4 ��m scale were on the order of 0.5 ��m leading to a coefficient of variation as high as 13%. Clearly, the transition from test to manufacturing for this process will require understanding the causes of this variation and devising control methods to minimize its magnitude over all types of parts.

The Inertio-Elastic Planar Entry Flow of Low-Viscosity Elastic Fluids in Micro-fabricated Geometries

The non-Newtonian flow of dilute aqueous polyethylene oxide (PEO) solutions through microfabricated planar abrupt contraction-expansions is investigated. The contraction geometries are fabricated from a high-resolution chrome mask and cross-linked PDMS gels using the tools of soft-lithography. The small length scales and high deformation rates in the contraction throat lead to significant extensional flow effects even with dilute polymer solutions having time constants on the order of milliseconds. The dimensionless extra pressure drop across the contraction increases by more than 200% and is accompanied by significant upstream vortex growth. Streak photography and videomicroscopy using epifluorescent particles shows that the flow ultimately becomes unstable and three-dimensional. The moderate Reynolds numbers (0.03 ������ Re ������ 44) associated with these high Deborah number (0 ������ De ������ 600) microfluidic flows results in the exploration of new regions of the Re-De parameter space in which the effects of both elasticity and inertia can be observed. Understanding such interactions will be increasingly important in microfluidic applications involving complex fluids and can best be interpreted in terms of the elasticity number, El = De/Re, which is independent of the flow kinematics and depends only on the fluid rheology and the characteristic size of the device.

El micro: un deporte de todos y para todos

Seg��n estudios realizados por la Federaci��n Colombiana de F��tbol de Sal��n, en Colombia existen al menos 1.2 millones de jugadores de este deporte, de los cuales una cuarta parte (300.000, aproximadamente) se encuentra en Bogot��. Tan s��lo en la capital del pa��s se juegan en un fin de semana m��s de 2.000 partidos oficiales y su liga es una de las m��s competitivas a nivel nacional. A continuaci��n presento tres cr��nicas que retratar��n de cerca la popularidad del microf��tbol en la ciudad de Bogot��. Son m��s de 50 a��os de un deporte que lleg�� al pa��s gracias al doctor Jaime Arroyave Rend��n pero que en cuarenta minutos se reinventa en los pies de los ���micreros��� bogotanos.

Intro to Matlab for Oceanography: Micro-lectures

This is a collection of 12 micro-lectures, to be used by students in advance of practical sessions. Durations range for 3 min to 10 min. Topics include: ****** 1. Introduction ****** 2. Data classes ****** 3. Matrices ****** 4. Getting help ****** 5. Index notation ****** 6. 1- and 2-dimensional data ****** 7. 3-dimensional data ****** 8. Booleans (True/False) ****** 9. Designing a programme (Algorithms) ****** 10. Flow control: If-then statements ****** 11. Flow control: For-do loops ****** 12. Making nicer figures ******

De lo micro a lo macro prudencial: Un an��lisis de la supervisi��n bancaria desde la econometr��a espacial

La crisis que se desat�� en el mercado hipotecario en Estados Unidos en 2008 y que logr�� propagarse a lo largo de todo sistema financiero, dej�� en evidencia el nivel de interconexi��n que actualmente existe entre las entidades del sector y sus relaciones con el sector productivo, dejando en evidencia la necesidad de identificar y caracterizar el riesgo sist��mico inherente al sistema, para que de esta forma las entidades reguladoras busquen una estabilidad tanto individual, como del sistema en general. El presente documento muestra, a trav��s de un modelo que combina el poder informativo de las redes y su adecuaci��n a un modelo espacial auto regresivo (tipo panel), la importancia de incorporar al enfoque micro-prudencial (propuesto en Basilea II), una variable que capture el efecto de estar conectado con otras entidades, realizando as�� un an��lisis macro-prudencial (propuesto en Basilea III).

El liderazgo empresarial para la innovaci��n tecnol��gica en las micro, peque��as y medianas empresas.

Este ensayo presenta un panorama acerca de las teor��as m��s relevantes alrededor del ���liderazgo���, para obtener los elementos b��sicos que podr��an facilitar el desarrollo de las micro, peque��as y medianas empresas mexicanas. Se revisaron diferentes teor��as incluyendo algunas de tipo psicol��g ico, base del liderazgo empresarial. Las concepciones sobre el liderazgo efectivo difieren de escritor a escritor. Los atributos asociados con ��ste mencionados con mayor frecuencia fueron: capacidad de correr riesgos, flexibilidad, confianza en s�� mismo, habilidades interpersonales, competencia para ejecutar tareas, inteligencia, firmeza para tomar decisiones, comprensi��n de los seguidores, buena comunicaci��n y valor o coraje.��