Scalable distributed virtual environments using multicast application level

Most of architectures proposed for developing Distributed Virtual Environment (DVE) allow limited number of users. To support the development of applications using the internet infrastructure, with hundred or, perhaps, thousands users logged simultaneously on DVE, several techniques for managing resources, such as bandwidth and capability of processing, must be implemented. The strategy presented in this paper combines methods to attain the scalability required, In special the multicast protocol at application level.

Processamento de nanomateriais em hidrotermal convencional e hidrotermal de microondas

Copper, zinc and nickel oxides present different properties in nanostructured form. These nanomaterials present very interesting morphologies such as urchin and flowers. This differents arquitechures can be employed in near future in several areas of applications as: nanocatalysis, nanooptoeletronic and nanomedicine.

Fatigue behaviour study on repaired aramid fiber/epoxy composites

Aramid fiber reinforced polymer composites have been used in a wide variety of applications, such as aerospace, marine, sporting equipment and in the defense sector, due to their outstanding properties at low density. The most widely adopted procedure to investigate the repair of composites has been by repairing damages simulated in composite specimens. This work presents the structural repair influence on tensile and fatigue properties of a typical aramid fiber/epoxy composite used in the aerospace industry. According to this work, the aramid/epoxy composites with and without repair present tensile strength values of 618 and 680MPa, respectively, and tensile modulus of 26.5 and 30.1 GPa, respectively. Therefore, the fatigue results show that in loads higher than 170 MPa, both composites present a low life cycle (lower than 200,000 cycles) and the repaired aramid/epoxy composite presented low fatigue resistance in low and high cycle when compared with non-repaired composite. With these results, it is possible to observe a decrease of the measured mechanical properties of the repaired composites.

Molecularly designed layer-by-layer (LbL) films to detect catechol using information visualization methods

The control of molecular architectures has been exploited in layer-by-layer (LbL) films deposited on Au interdigitated electrodes, thus forming an electronic tongue (e-tongue) system that reached an unprecedented high sensitivity (down to 10-12 M) in detecting catechol. Such high sensitivity was made possible upon using units containing the enzyme tyrosinase, which interacted specifically with catechol, and by processing impedance spectroscopy data with information visualization methods. These latter methods, including the parallel coordinates technique, were also useful for identifying the major contributors to the high distinguishing ability toward catechol. Among several film architectures tested, the most efficient had a tyrosinase layer deposited atop LbL films of alternating layers of dioctadecyldimethylammonium bromide (DODAB) and 1,2-dipalmitoyl-sn-3-glycero-fosfo-rac-(1-glycerol) (DPPG), viz., (DODAB/DPPG)5/DODAB/Tyr. The latter represents a more suitable medium for immobilizing tyrosinase when compared to conventional polyelectrolytes. Furthermore, the distinction was more effective at low frequencies where double-layer effects on the film/liquid sample dominate the electrical response. Because the optimization of film architectures based on information visualization is completely generic, the approach presented here may be extended to designing architectures for other types of applications in addition to sensing and biosensing. © 2013 American Chemical Society.

Simple green approach to reinforce natural rubber with bacterial cellulose nanofibers

Natural rubber (NR) is a renewable polymer with a wide range of applications, which is constantly tailored, further increasing its utilizations. The tensile strength is one of its most important properties susceptible of being enhanced by the simple incorporation of nanofibers. The preparation and characterization of natural-rubber based nanocomposites reinforced with bacterial cellulose (BC) and bacterial cellulose coated with polystyrene (BCPS), yielded high performance materials. The nanocomposites were prepared by a simple and green process, and characterized by tensile tests, dynamical mechanical analysis (DMA), scanning electron microscopy (SEM), and swelling experiments. The effect of the nanofiber content on morphology, static, and dynamic mechanical properties was also investigated. The results showed an increase in the mechanical properties, such as Young's modulus and tensile strength, even with modest nanofiber loadings. © 2013 American Chemical Society.

Integridade, disponibilidade e acurácia no posicionamento RTK e RTK em rede: Investigação no contexto da rede GNSS ativa do Estado de São Paulo

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Imagens multitemporais ALOS/PALSAR baseada em orientação a objeto na discriminação da cobertura da terra

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise de séries temporais de coordenadas estimadas com GPS: uma proposta metodológica para eliminação de efeitos sazonais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Solução do problema de corte bidimensional de peças retângulares tipo não-guilhotinado usando simulated annealing

Pós-graduação em Engenharia Elétrica - FEIS

Preparação e caracterização de óxido de zinco nanoestruturado

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Influência do pH da suspensão coloidal nas propriedades de filmes finos de Sn'O IND. 2'

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeito de multicaminho de alta frequência no posicionamento relativo GPS estático: detecção e atenuação utilizando wavelets

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Campo de velocidade para as estações da RBMC e do IGS localizados na placa Sul-Americana: estimativa a partir do processamento de dados GPS

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise de multirresolução baseada em polinômio potência de Sigmóide - Wavelet

Pós-graduação em Ciência da Computação - IBILCE

Análise técnica e econômica da resinagem de Pinus elliottii Engelm. var. elliottii na região de Manduri, SP

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)