Inflow cannula design for biventricular assist devices

Cardiovascular diseases are a leading cause of death throughout the developed world. With the demand for donor hearts far exceeding the supply, a bridge-to-transplant or permanent solution is required. This is currently achieved with ventricular assist devices (VADs), which can be used to assist the left ventricle (LVAD), right ventricle (RVAD), or both ventricles simultaneously (BiVAD). Earlier generation VADs were large, volume-displacement devices designed for temporary support until a donor heart was found. The latest generation of VADs use rotary blood pump technology which improves device lifetime and the quality of life for end stage heart failure patients. VADs are connected to the heart and greater vessels of the patient through specially designed tubes called cannulae. The inflow cannulae, which supply blood to the VAD, are usually attached to the left atrium or ventricle for LVAD support, and the right atrium or ventricle for RVAD support. Few studies have characterized the haemodynamic difference between the two cannulation sites, particularly with respect to rotary RVAD support. Inflow cannulae are usually made of metal or a semi-rigid polymer to prevent collapse with negative pressures. However suction, and subsequent collapse, of the cannulated heart chamber can be a frequent occurrence, particularly with the relatively preload insensitive rotary blood pumps. Suction events may be associated with endocardial damage, pump flow stoppages and ventricular arrhythmias. While several VAD control strategies are under development, these usually rely on potentially inaccurate sensors or somewhat unreliable inferred data to estimate preload. Fixation of the inflow cannula is usually achieved through suturing the cannula, often via a felt sewing ring, to the cannulated chamber. This technique extends the time on cardiopulmonary bypass which is associated with several postoperative complications. The overall objective of this thesis was to improve the placement and design of rotary LVAD and RVAD inflow cannulae to achieve enhanced haemodynamic performance, reduced incidence of suction events, reduced levels of postoperative bleeding and a faster implantation procedure. Specific objectives were: * in-vitro evaluation of LVAD and RVAD inflow cannula placement, * design and in-vitro evaluation of a passive mechanism to reduce the potential for heart chamber suction, * design and in-vitro evaluation of a novel suture-less cannula fixation device. In order to complete in-vitro evaluation of VAD inflow cannulae, a mock circulation loop (MCL) was developed to accurately replicate the haemodynamics in the human systemic and pulmonary circulations. Validation of the MCL’s haemodynamic performance, including the form and magnitude of pressure, flow and volume traces was completed through comparisons of patient data and the literature. The MCL was capable of reproducing almost any healthy or pathological condition, and provided a useful tool to evaluate VAD cannulation and other cardiovascular devices. The MCL was used to evaluate inflow cannula placement for rotary VAD support. Left and right atrial and ventricular cannulation sites were evaluated under conditions of mild and severe heart failure. With a view to long term LVAD support in the severe left heart failure condition, left ventricular inflow cannulation was preferred due to improved LVAD efficiency and reduced potential for thrombus formation. In the mild left heart failure condition, left atrial cannulation was preferred to provide an improved platform for myocardial recovery. Similar trends were observed with RVAD support, however to a lesser degree due to a smaller difference in right atrial and ventricular pressures. A compliant inflow cannula to prevent suction events was then developed and evaluated in the MCL. As rotary LVAD or RVAD preload was reduced, suction events occurred in all instances with a rigid inflow cannula. Addition of the compliant segment eliminated suction events in all instances. This was due to passive restriction of the compliant segment as preload dropped, thus increasing the VAD circuit resistance and decreasing the VAD flow rate. Therefore, the compliant inflow cannula acted as a passive flow control / anti-suction system in LVAD and RVAD support. A novel suture-less inflow cannula fixation device was then developed to reduce implantation time and postoperative bleeding. The fixation device was evaluated for LVAD and RVAD support in cadaveric animal and human hearts attached to a MCL. LVAD inflow cannulation was achieved in under two minutes with the suture-less fixation device. No leakage through the suture-less fixation device – myocardial interface was noted. Continued development and in-vivo evaluation of this device may result in an improved inflow cannulation technique with the potential for off-bypass insertion. Continued development of this research, in particular the compliant inflow cannula and suture-less inflow cannulation device, will result in improved postoperative outcomes, life span and quality of life for end-stage heart failure patients.

BWW ontology as a lens on IS design theory: Extending the design science research roadmap

The Design Science Research Roadmap (DSR-Roadmap) [1] aims to give detailed methodological guidance to novice researchers in Information Systems (IS) DSR. Focus group evaluation, one phase of the overall study, of the evolving DSR-Roadmap revealed that a key difficulty faced by both novice and expert researchers in DSR, is abstracting design theory from design. This paper explores the extension of the DSR-Roadmap by employing IS deep structure ontology (BWW [2-4]) as a lens on IS design to firstly yield generalisable design theory, specifically 'IS Design Theory' (ISDT) elements [5]. Consideration is next given to the value of BWW in the application of the design theory by practitioners. Results of mapping BWW constructs to ISDT elements suggest that the BWW is promising as a common language between design researchers and practitioners, facilitating both design theory and design implementation

The design science research roadmap : in progress evaluation

Although Design Science Research (DSR) is now an accepted approach to research in the Information Systems (IS) discipline, consensus on the methodology of DSR has yet to be achieved. Lack of a comprehensive and detailed methodology for Design Science Research (DSR) in the Information System (IS) discipline is a main issue. Prior research (the parent-study) aimed to remedy this situation and resulted in the DSR-Roadmap (Alturki et al., 2011a). Continuing empirical validation and revision of the DSR-Roadmap strives towards a methodology with appropriate levels of detail, integration, and completeness for novice researchers to efficiently and effectively conduct and report DSR in IS. The sub-study reported herein contributes to this larger, ongoing effort. This paper reports results from a formative evaluation effort of the DSR-Roadmap conducted using focus group analysis. Generally, participants endorsed the utility and intuitiveness of the DSR-Roadmap, while also suggesting valuable refinements. Both parent-study and sub-study make methodological contributions. The parent-study is the first attempt of utilizing DSR to develop a research methodology showing an example of how to use DSR in research methodology construction. The sub-study demonstrates the value of the focus group method in DSR for formative product evaluation.

Framework for implementing design build project delivery system in road infrastructure in Indonesia

The thesis provides a framework for potential implementation of the design-build (DB) project delivery system in road infrastructure projects in Indonesia. This framework proposed a structure of the hierarchy of factors promoting the potential implementation of the DB project delivery system and introduced ways to implement the DB project delivery system through level of hierarchical factors. These findings not only give benefit to the academic knowledge but also to the public officials in guiding them with regard to the priority of promoting factors in the process to implement the DB system.

Integration of Saudi Arabia’s conservative Islamic culture in sustainable housing design

The cities of Saudi Arabia have perhaps the largest growth rates of cities in the Middle East, such that it has become a cause in shortage of housing for mid and low-income families, as is the case in other developing countries. Even when housing is found, it is not sustainable nor is it providing the cultural needs of those families. The aim of this paper is to integrate the unique conservative Islamic Saudi culture into the design of sustainable housing. This paper is part of a preliminary study of an on-going PhD thesis, which utilises a semistructured interview of a panel of nine experts in collecting the data. The interviews consisted of ten questions ranging from general questions such as stating their expertise and work position to more specific question such as listing the critical success factors and/or barriers for applying sustainability to housing in Saudi Arabia. Since the participants were selected according to their experience, the answers to the interview questions were satisfactory where the generation of the survey questions for the second stage in the PhD thesis took place after analysing the participant’s answers to the interview questions. This paper recommends design requirements for accommodating the conservative Islamic Saudi Culture in low cost sustainable houses. Such requirements include achieving privacy through the use of various types of traditional Saudi architectural elements, such as the method of decorative screening of windows, called Mashrabiya, and having an inner courtyard where the house looks inward rather than outward. Other requirements include educating firms on how to design sustainable housing, educating the public on the advantages of sustainable housing and implementing new laws that enforce the utilisation of sustainable methods to housing construction. This paper contributes towards the body of knowledge by proposing initial findings on how to integrate the conservative Islamic culture of Saudi Arabia into the design of a sustainable house specifically for mid and low-income families. This contribution can be implemented on developing countries in the region that are faced with housing shortage for mid and low-income families.

Design of a professional development programme for palliative care nurses (Part Two)

Yates et al (1996) provided a review of the literature on educational approaches to improving psychosocial care of terminally ill patients and their families and suggested that there was an urgent need for innovation in this area. A programme of professional development currently being offered to 181 palliative care nurses in Queensland, Australia, was also described. This paper presents research in progress evaluating this programme which involves use of a quasi-experimental pre-post test design. It also includes process and outcome measures to assess effectiveness in improving the participant's ability to provide psychosocial care to patients and families. Research examining the effectiveness of various educational programmes on care of the dying has offered equivocal results (Yates et al 1996). Degner and Gow (1988a) noted that the inconsistencies found in research into death education result from inadequate study designs, variations in the conceptualisation and measurement of the outcomes of the programmes and flaws in data analysis. Such studies have often lacked a theoretical basis, few have employed well-controlled experimental designs, and the programme outcomes have generally been limited to the participant's 'death anxiety', or other death attitudes which have been variously defined and measured. Whilst Degner and Gow (1988b) have reported that undergraduate nursing students who participated in a care of the dying educational programme demonstrated more 'approach caring' behaviours than a control group, the impact of education programmes on patient care has rarely been examined. Failure to link education to nursing practice and subsequent clinical outcomes has, however, been seen as a major limitation of nursing knowledge in this area (Degner et al 1991). This paper describes an approach to researching the effectiveness of professional development programmes for palliative care nurses.

Collaborative learning and critical thinking in technology-enhanced environments : an instructional design framework

The nature and characteristics of how learners learn today are changing. As technology use in learning and teaching continues to grow, its integration to facilitate deep learning and critical thinking becomes a primary consideration. The implications for learner use, implementation strategies, design of integration frameworks and evaluation of their effectiveness in learning environments cannot be overlooked. This study specifically looked at the impact that technology-enhanced learning environments have on different learners’ critical thinking in relation to eductive ability, technological self-efficacy, and approaches to learning and motivation in collaborative groups. These were explored within an instructional design framework called CoLeCTTE (collaborative learning and critical thinking in technology-enhanced environments) which was proposed, revised and used across three cases. The field of investigation was restricted to three key questions: 1) Do learner skill bases (learning approach and eductive ability) influence critical thinking within the proposed CoLeCTTE framework? If so, how?; 2) Do learning technologies influence the facilitation of deep learning and critical thinking within the proposed CoLeCTTE framework? If so, how?; and 3) How might learning be designed to facilitate the acquisition of deep learning and critical thinking within a technology-enabled collaborative environment? The rationale, assumptions and method of research for using a mixed method and naturalistic case study approach are discussed; and three cases are explored and analysed. The study was conducted at the tertiary level (undergraduate and postgraduate) where participants were engaged in critical technical discourse within their own disciplines. Group behaviour was observed and coded, attributes or skill bases were measured, and participants interviewed to acquire deeper insights into their experiences. A progressive case study approach was used, allowing case investigation to be implemented in a "ladder-like" manner. Cases 1 and 2 used the proposed CoLeCTTE framework with more in-depth analysis conducted for Case 2 resulting in a revision of the CoLeCTTE framework. Case 3 used the revised CoLeCTTE framework and in-depth analysis was conducted. The findings led to the final version of the framework. In Cases 1, 2 and 3, content analysis of group work was conducted to determine critical thinking performance. Thus, the researcher used three small groups where learner skill bases of eductive ability, technological self-efficacy, and approaches to learning and motivation were measured. Cases 2 and 3 participants were interviewed and observations provided more in-depth analysis. The main outcome of this study is analysis of the nature of critical thinking within collaborative groups and technology-enhanced environments positioned in a theoretical instructional design framework called CoLeCTTE. The findings of the study revealed the importance of the Achieving Motive dimension of a student’s learning approach and how direct intervention and strategies can positively influence critical thinking performance. The findings also identified factors that can adversely affect critical thinking performance and include poor learning skills, frustration, stress and poor self-confidence, prioritisations over learning; and inadequate appropriation of group role and tasks. These findings are set out as instructional design guidelines for the judicious integration of learning technologies into learning and teaching practice for higher education that will support deep learning and critical thinking in collaborative groups. These guidelines are presented in two key areas: technology and tools; and activity design, monitoring, control and feedback.

Changing work design in disaster response : the potential for innovation

Work design operates as the system of arrangements and procedures for organizing work to achieve organizational goals. These systems are commonly established in periods of environmental and organizational stability and formulated to achieve efficiencies in resources, employee and team configuration. However, organizations charged with responding to disasters need to be prepared to respond to unexpected events on a large scale, and disaster response planning needs to accommodate a broad range of possible disasters. When the disaster state occurs, enactment of the specific organizational response is devolved to group or individual level managers. While this enactment presents a range of risks, it also provides a potential avenue for innovation. Employees ultimately are the foundation of change and innovation, as it is people who develop, respond, change and implement new ideas. This study analyzes motivational characteristics of work design at an Australian humanitarian organization encompassing normal operations and periods of disaster activation. The study will identify the paradox of dual work designs and the implications for organizational innovation.

Design, sustainability and Australian mass-market fashion : three case studies

The production of fashion garments has negative environmental and social impacts that can potentially be reduced through decisions made in the design process. This research explores to what extent Australian mass-market fashion designers consider environmental sustainability within product design. The study presents three case studies from different market levels, assembled through interviews with designers, along with an analysis of the Australian mass-market fashion industry. The project provides insights into the workings of the fashion design process within mid and high volume companies, and identifies opportunities and barriers for consideration of sustainability.

Growing existing aboriginal designs to guide a cross-cultural design project

Designing across cultures requires considerable attention to inter-relational design methods that facilitate mutual exploration, learning and trust. Many Western design practices have been borne of a different model, utilizing approaches for the design team to rapidly gain insight into “users” in order to deliver concepts and prototypes, with little attention paid to different cultural understandings about being, knowledge, participation and life beyond the design project. This paper describes a project that intends to create and grow a sustainable set of technology assisted communication practices for the Warnindilyakwa people of Groote Eylandt in the form of digital noticeboards. Rather than academic practices of workshops, interviews, probes or theoretical discourses that emphasize an outside-in perspective, we emphasize building upon the local designs and practices. Our team combines bilingual members from the local Land Council in collaboration with academics from a remote urban university two thousand kilometers away. We contribute an approach of growing existing local practices and materials digitally in order to explore viable, innovative and sustainable technical solutions from this perspective.

Towards engaged consumption : new sources of inspiration for eco-feedback design

Eco-feedback interventions are capable of producing reductions in household energy consumption. Yet less is known about exactly how this reduction is achieved, how to maximise user engagement, or how to effectively translate engagement into energy saving. This paper discusses design opportunities for eco-feedback systems through observations of domestic energy use in both Western and rural developing world contexts. Drawing on case studies from these two contexts including 21 empirical interviews, we present an alternative framework for human-resource interaction, highlighting design opportunities for a transition towards more engaged and sustainable energy consumption among users.

Analysis of the design-construction supply chain in the thermal performance of sub-tropical and tropical housing

Background: In sub-tropical and tropical Queensland, a legacy of poor housing design,minimal building regulations with few compliance measures, an absence of post-construction performance evaluation and various social and market factors has led to a high and growing penetration of, and reliance on, air conditioners to provide thermal comfort for occupants. The pervasive reliance on air conditioners has arguably impacted on building forms, changed cultural expectations of comfort and social practices for achieving comfort, and may have resulted in a loss of skills in designing and constructing high performance building envelopes. Aim: The aim of this paper is to report on initial outcomes of a project that sought to determine how the predicted building thermal performance of twenty-five houses in subtropical and tropical Queensland compared with objective performance measures and comfort performance as perceived by occupants. The purpose of the project was to shed light on the role of various supply chain agents in the realisation of thermal performance outcomes. Methodology: The case study methodology embraced a socio-technical approach incorporating building science and sociology. Building simulation was used to model thermal performance under controlled comfort assumptions and adaptive comfort conditions. Actual indoor climate conditions were measured by temperature and relative humidity sensors placed throughout each house, whilst occupants’ expectations of thermal comfort and their self-reported behaviours were gathered through semi-structured interviews and periodic comfort surveys. Thermal imaging and air infiltration tests, along with building design documents, were analysed to evaluate the influence of various supply chain agents on the actual performance outcomes. Results: The results clearly show that in the housing supply chain – from designer to constructor to occupant – there is limited understanding from each agent of their role in contributing to, or inhibiting, occupants’ comfort.

Power converters design and analysis for high power piezoelectric ultrasonic transducers

High power piezoelectric ultrasonic transducers have been widely exploited in a variety of applications. The critical behaviour of a piezoelectric device is encapsulated in its resonant frequencies because of its maximum transmission performance at these frequencies. Therefore power electronic converters should be tuned at those resonant frequencies to transfer electrical power to mechanical power efficiently. However, structural and environmental changes cause variations in the device resonant frequencies which can degrade the system performance. Hence, estimating the device resonant frequencies within the incorporated setup can significantly improve the system performance. This paper proposes an efficient resonant frequency estimation approach to maintain the performance of high power ultrasonic applications using the employed power converter. Experimental validations indicate the effectiveness of the proposed method.

Supporting context-aware process design : learnings from a design science study

Recent studies have started to explore context-awareness as a driver in the design of adaptable business processes. The emerging challenge of identifying and considering contextual drivers in the environment of a business process are well understood, however, typical methods and models for business process design do not yet consider this context. In this paper, we describe our work on the design of a method framework and appropriate models to enable a context-aware process design approach. We report on our ongoing work with an Australian insurance provider and describe the design science we employed to develop innovative and useful artifacts as part of a context-aware method framework. We discuss the utility of these artifacts in an application in the claims handling process at the case organization.

Improving the design of online applications for social benefit through a behaviour change model

Community support agencies routinely employ a web presence to provide information on their services. While this online information provision helps to increase an agency’s reach, this paper argues that it can be further extended by mapping relationships between services and by facilitating two-way communication and collaboration with local communities. We argue that emergent technologies, such as locative media and networking tools, can assist in harnessing this social capital. However, new applications must be designed in ways that both persuade and support community members to contribute information and support others in need. An analysis of the online presence of community service agencies and social benefit applications is presented against Fogg’s Behaviour Model. From this evaluation, design principles are proposed for developing new locative, collaborative online applications for social benefit.