864 resultados para Fusão


Relevância:

10.00% 10.00%

Publicador:

Resumo:

The discovery of giant stars in the spectral regions G and K, showing moderate to rapid rotation and single behavior, namely with constant radial velocity, represents one important topic of study in Stellar Astrophysics. Indeed, such anomalous rotation clearly violates the theoretical predictions on the evolution of stellar rotation, since in evolved evolutionary stages is expected that the single stars essentially have low rotation due to the evolutionary expansion. This property is well-established from the observational point of view, with different studies showing that for single giant stars of spectral types G and K values of the rotation are typically smaller than 5kms−1 . This Thesis seeks an effective contribution to solving the paradigm described above, aiming to search for single stars of spectral types G and K with anomalous rotation, tipically rotation of moderate to rapid, in other luminosity classes. In this context, we analyzed a large stellar sample consisting of 2010 apparently single stars of luminosity classes IV, III, II and Ib with spectral types G and K, with rotational velocity v sin i and radial velocity measurements obtained from observations made by CORAVEL spectrometers. As a first result of impact we discovered the presence of anomalous rotators also among subgiants, bright giants and supergiants stars, namelly stars of luminosity classes IV, II and Ib, in contrast to previous studies, that reported anomalous rotators only in the luminosity class III classic giants. Such a finding of great significance because it allows us to analyze the presence of anomalous rotation at different intervals of mass, since the luminosity classes considered here cover a mass range between 0.80 and 20MJ, approximately. In the present survey we discovered 1 subgiant, 9 giants, 2 bright giants and 5 Ib supergiants, in spectral regions G and K, with values of v sin i ≥ 10kms−1 and single behavior. This amount of 17 stars corresponds to a frequency of 0.8% of G and K single evolved stars with anomalous rotation in the mentioned classes of luminosities, listed at the Bright Star Catalog, which is complete to visual magnitude 6.3. Given these new findings, based on a stellar sample complete in visual magnitude, as that of the Bright Star Catalog, we conducted a comparative statistical analysis using the Kolmogorov- Smirnov test, from where we conclude that the distributions of rotational velocity, v sin i, for single evolved stars with anomalous rotation in luminosity classes III and II, are similar to the distributions of v sin i for spectroscopic binary systems with evolved components with the same spectral type and luminosity class. This vii result indicates that the process of coalescence between stars of a binary system might be a possible mechanism to explain the observed abnormal rotation in the referred abnormal rotators, at least among the giants and bright giants, where the rotation in excess would be associated with the transfer of angular momentum for the star resulting from the merger. Another important result of this Thesis concerns the behavior of the infrared emission in most of the stars with anomalous rotation here studied, where 14 stars of the sample tend to have an excess in IR compared with single stars with low rotation, within of their luminosity class. This property represents an additional link in the search for the physical mechanisms responsible for the abnormal observed rotation, since recent theoretical studies show that the accretion of objects of sub-stellar mass, such as brown dwarfs and giant planets, by the hosting star, can significantly raise its rotation, producing also a circumstellar dust disk. This last result seems to point in that direction, since it is not expected that dust disks occurring during the stage of star formation can survive until the stages of subgiants, giants and supergiants Ib. In summary, in this Thesis, besides the discovery of single G and K evolved stars of luminosity classes IV, II and Ib with anomalously high rotation compared to what is predicted by stellar evolution theory, we also present the frequency of these abnormal rotators in a stellar sample complete to visual magnitude 6.3. We also present solid evidence that coalescence processes in stellar binary systems and processes of accretion of brown dwarfs star or giant planets, by the hosting stars, can act as mechanisms responsible for the puzzling phenomenon of anomalous rotation in single evolved stars.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Relevância:

10.00% 10.00%

Publicador:

Resumo:

This paper suggests modifications in coating of electrodes providing an alternative for execution of welding with low hydrogen electrode AWS E7018 without having to dry it, reducing thus the cost and time of manufacturing of high resistance welds. The welds in this research were developed with basic coated electrodes (hygroscopic) – SMAW process – externally painted with aluminum spray paint for high temperatures or wrapped with thin plastic films (PVC) and aluminum foil films used commonly for food protection. The basic premise is that establishing a barrier between the atmosphere and the electrode coating could reduce the effects of high hygroscopicity presented by coatings of low hydrogen, minimizing this way the main source of supply of hydrogen to the fusion pool during welding. It is also expected that the addition of new materials from the electrode coating to the fusion pool would induce metallurgical changes in the deposited metal and, as a consequence, modifications in its mechanical properties. This research dealt with measuring the dissolved hydrogen in the deposited metal after welding with modified electrodes, evaluating the influence of these changes in the produced microstructures and in the mechanical properties of the resulting weld, and comparing the obtained results with the standard welding procedures and with the recently developed waterproof electrodes. The results obtained in most samples welded with modified electrodes showed increased mechanical resistance and increased tenacity due to the increased percentage of acicular ferrite in metal deposited without significant elevation of hardness, when compared with the traditional welding with AWS E7018 electrode and with ELBRÁS BRH4R waterproof electrode. The diffusing hydrogen measured in the modified electrodes was kept inside the parameters defined by international codes.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

This paper suggests modifications in coating of electrodes providing an alternative for execution of welding with low hydrogen electrode AWS E7018 without having to dry it, reducing thus the cost and time of manufacturing of high resistance welds. The welds in this research were developed with basic coated electrodes (hygroscopic) – SMAW process – externally painted with aluminum spray paint for high temperatures or wrapped with thin plastic films (PVC) and aluminum foil films used commonly for food protection. The basic premise is that establishing a barrier between the atmosphere and the electrode coating could reduce the effects of high hygroscopicity presented by coatings of low hydrogen, minimizing this way the main source of supply of hydrogen to the fusion pool during welding. It is also expected that the addition of new materials from the electrode coating to the fusion pool would induce metallurgical changes in the deposited metal and, as a consequence, modifications in its mechanical properties. This research dealt with measuring the dissolved hydrogen in the deposited metal after welding with modified electrodes, evaluating the influence of these changes in the produced microstructures and in the mechanical properties of the resulting weld, and comparing the obtained results with the standard welding procedures and with the recently developed waterproof electrodes. The results obtained in most samples welded with modified electrodes showed increased mechanical resistance and increased tenacity due to the increased percentage of acicular ferrite in metal deposited without significant elevation of hardness, when compared with the traditional welding with AWS E7018 electrode and with ELBRÁS BRH4R waterproof electrode. The diffusing hydrogen measured in the modified electrodes was kept inside the parameters defined by international codes.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Composites based on alumina (Al2O3), tungsten carbide (WC) and cobalt (Co) exhibit specific properties such as low density, high oxidation resistance, high melting point and high chemical inertia. That composite shows to be a promising material for application in various fields of engineering. In this work, the mechanical properties of the composite (Al2O3 – WC – Co), particularly density and hardness, were evaluated according to the effects of the variables of powder processing parameters, green compact and sintered. Powder composites with the composition of 80 wt% Al2O3, 18 wt% WC and 2 wt% Co were processed by high energy ball milling in a planetary mill for 50 hours as well as mixed by manual mixing in a glass vessel with the same proportion. Samples were collected (2, 10, 20, 30, 40 and 50 hours) during the milling process. Then, the powders were compacted in a cylindrical die with 5 mm in diameter in a uniaxial press with pressures of 200 and 400 MPa. The sintering was in two stages: first, the solid phase sintering was performed at 1126 and 1300 °C for 1 hour with a heating rate of 10 °C/min in a resistive furnace under argon atmosphere for green samples compacted in 200 and 400 MPa; the second sintering was performed on dilatometer in solid phase at 1300 °C for green sample compacted in 200 MPa, another sintering also was performed on dilatometer, this time in liquid phase at 1550 °C for green samples compacted in 200 and 400 MPa, with the same parameters used in resistive furnace. The raw materials were characterized by X – ray diffraction (XRD), X – ray fluorescence (XRF), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and laser particlemeter. The sintered samples were subjected to microhardness testing. The results showed that high energy milling achieved to the objectives regarding the particle size and the dispersion of composite phases. However, the hardness did not achieve to significant results, this is an indication that the composite has low fracture toughness.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Composites based on alumina (Al2O3), tungsten carbide (WC) and cobalt (Co) exhibit specific properties such as low density, high oxidation resistance, high melting point and high chemical inertia. That composite shows to be a promising material for application in various fields of engineering. In this work, the mechanical properties of the composite (Al2O3 – WC – Co), particularly density and hardness, were evaluated according to the effects of the variables of powder processing parameters, green compact and sintered. Powder composites with the composition of 80 wt% Al2O3, 18 wt% WC and 2 wt% Co were processed by high energy ball milling in a planetary mill for 50 hours as well as mixed by manual mixing in a glass vessel with the same proportion. Samples were collected (2, 10, 20, 30, 40 and 50 hours) during the milling process. Then, the powders were compacted in a cylindrical die with 5 mm in diameter in a uniaxial press with pressures of 200 and 400 MPa. The sintering was in two stages: first, the solid phase sintering was performed at 1126 and 1300 °C for 1 hour with a heating rate of 10 °C/min in a resistive furnace under argon atmosphere for green samples compacted in 200 and 400 MPa; the second sintering was performed on dilatometer in solid phase at 1300 °C for green sample compacted in 200 MPa, another sintering also was performed on dilatometer, this time in liquid phase at 1550 °C for green samples compacted in 200 and 400 MPa, with the same parameters used in resistive furnace. The raw materials were characterized by X – ray diffraction (XRD), X – ray fluorescence (XRF), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and laser particlemeter. The sintered samples were subjected to microhardness testing. The results showed that high energy milling achieved to the objectives regarding the particle size and the dispersion of composite phases. However, the hardness did not achieve to significant results, this is an indication that the composite has low fracture toughness.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The Middle Devonian-Early Carboniferous sequence of the Parnaíba Basin, lithostratigraphically defined as Canindé Group, has been reinterpreted using the basic model of sequence stratigraphy. Therefore, lithology and gamma ray well-logs and seismic lines of central portion of the basin were analyzed, producing up from there diagrams 1D, isochore maps and stratigraphic sections. As results of this study, were defined two depositional cycles of second order, referred as Depositional Sequence 1 (SEQ1) and the Depositional Sequence 2 (SEQ2). The SEQ1, with interval about 37 Ma, is limited below by Early Devonian Unconformity and is equivalent to the formations Itaim, Pimenteiras and Cabeças. The SEQ2, which follows, comprises a range of about 15 Ma and is equivalent to the Longá Formation The SEQ1 starts with the lowstand systems tract, consisting of progradational parasequence set in the basal part, predominantly pelitic, deposited on a prodelta under influence of storms and the upper part consists in sandstones of deltaic front, with the maximum regressive surface on the upper limit. The transgressive systems tract, deposited above, is characterized by retrogradacional parasequence set composed of shallow shelf mudstones, deposited under storm conditions. The maximum flooding surface, upper limit of this tract, is positioned in a shale level whose radioactivity in gammaray well-log is close to 150 API. The highstand systems tract presents progradational parasequence set, comprising mudstones and sandstones deposited in shelf, fluvial-estuarine or deltaic and periglacial environments, with the upper limit the Late Devonian Unconformity. The SEQ2 was deposited in shelf environment, starting with the lowstand systems tract, that is characterized by a progradational parasequence set, followed by the transgressive systems tract, with retrogradational character. The upper limit of the tract corresponding to the fusion between maximum flooding surface with the upper limit of this sequence, which is the Early Carboniferous Unconformity, where the overlapping section was eroded. This section, which corresponds the highstand systems tract is restricted to portions at which the erosion that generate the Early-Carboniferous Unconformity was less effective, preserving the records of this unit.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The Middle Devonian-Early Carboniferous sequence of the Parnaíba Basin, lithostratigraphically defined as Canindé Group, has been reinterpreted using the basic model of sequence stratigraphy. Therefore, lithology and gamma ray well-logs and seismic lines of central portion of the basin were analyzed, producing up from there diagrams 1D, isochore maps and stratigraphic sections. As results of this study, were defined two depositional cycles of second order, referred as Depositional Sequence 1 (SEQ1) and the Depositional Sequence 2 (SEQ2). The SEQ1, with interval about 37 Ma, is limited below by Early Devonian Unconformity and is equivalent to the formations Itaim, Pimenteiras and Cabeças. The SEQ2, which follows, comprises a range of about 15 Ma and is equivalent to the Longá Formation The SEQ1 starts with the lowstand systems tract, consisting of progradational parasequence set in the basal part, predominantly pelitic, deposited on a prodelta under influence of storms and the upper part consists in sandstones of deltaic front, with the maximum regressive surface on the upper limit. The transgressive systems tract, deposited above, is characterized by retrogradacional parasequence set composed of shallow shelf mudstones, deposited under storm conditions. The maximum flooding surface, upper limit of this tract, is positioned in a shale level whose radioactivity in gammaray well-log is close to 150 API. The highstand systems tract presents progradational parasequence set, comprising mudstones and sandstones deposited in shelf, fluvial-estuarine or deltaic and periglacial environments, with the upper limit the Late Devonian Unconformity. The SEQ2 was deposited in shelf environment, starting with the lowstand systems tract, that is characterized by a progradational parasequence set, followed by the transgressive systems tract, with retrogradational character. The upper limit of the tract corresponding to the fusion between maximum flooding surface with the upper limit of this sequence, which is the Early Carboniferous Unconformity, where the overlapping section was eroded. This section, which corresponds the highstand systems tract is restricted to portions at which the erosion that generate the Early-Carboniferous Unconformity was less effective, preserving the records of this unit.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The Potiguar Basin is located in the Brazilian Equatorial Margin and presents sedimentary rocks affected by Cenozoic basic igneous intrusions, known as Macau Magmatism. The most prominent effect related to these intrusions is the formation of buchites, pyrometamorphic rocks that occur at very high temperatures and very low pressures in the sanidinite metamorphic facies. Through literature review, field observations, petrographic and petrophysical data, accessing the database of previous studies and results from this research, it was possible to characterize and estimate the effects produced in the thermal aureole of some hypabyssal bodies in the basin. The most relevant features associated with the intrusions are: compactation, hydraulic fracturing, partial melting and recrystallization of country rocks. According to the observed mineral occurrences, temperature of 800 to 1200 °C and pressure below 0,5 kbar were estimated at the contacts of the igneous bodies. The thermal modeling of the São João plug indicates thermal effects extending up to 150 m away from the contact and cooling time of approximately 265,000 years. After the peak of temperature, followed a cooling phase registered by remobilization and precipitation of minerals at low-temperature in faults, fractures and geodes, interpreted as derived from reactions with sedimentary rocks and metasomatic / hydrothermal fluids with abundant carbonatization and silicification.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The Potiguar Basin is located in the Brazilian Equatorial Margin and presents sedimentary rocks affected by Cenozoic basic igneous intrusions, known as Macau Magmatism. The most prominent effect related to these intrusions is the formation of buchites, pyrometamorphic rocks that occur at very high temperatures and very low pressures in the sanidinite metamorphic facies. Through literature review, field observations, petrographic and petrophysical data, accessing the database of previous studies and results from this research, it was possible to characterize and estimate the effects produced in the thermal aureole of some hypabyssal bodies in the basin. The most relevant features associated with the intrusions are: compactation, hydraulic fracturing, partial melting and recrystallization of country rocks. According to the observed mineral occurrences, temperature of 800 to 1200 °C and pressure below 0,5 kbar were estimated at the contacts of the igneous bodies. The thermal modeling of the São João plug indicates thermal effects extending up to 150 m away from the contact and cooling time of approximately 265,000 years. After the peak of temperature, followed a cooling phase registered by remobilization and precipitation of minerals at low-temperature in faults, fractures and geodes, interpreted as derived from reactions with sedimentary rocks and metasomatic / hydrothermal fluids with abundant carbonatization and silicification.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Per investigare il ruolo del contrasto di densità fra rocce crostali e mantelliche, nell’origine dell’associazione peridotiti-migmatiti-gneiss della Zona d’Ultimo (Austroalpino superiore, Italia), durante l’orogenesi Varisica, sono stati studiati tre diversi litotipi provenienti dall’area in esame. Mediante l’utilizzo del software Perple_X, sono state modellizzate le condizioni P-T di equilibrio di: un paragneiss a granato e staurolite di grado metamorfico medio, un fels a granato prodotto per fusione parziale ed estrazione del fuso dalla roccia sorgente (restite), e una peridotite ad anfibolo rappresentativa del cuneo di mantello. A partire dalle peridotiti, sono state calcolate condizioni metamorfiche di picco per la Zona d’Ultimo di 900 °C e 13 kbar, in facies granulitica, confrontabili con profondità di circa 40-50 km. In queste condizioni, le peridotiti ad anfibolo presentano una densità di 3230 kg/m3, nettamente inferiore rispetto a quanto calcolato per il campione di restite, cioè 3730 kg/m3. In particolare, è stato calcolato che è necessario estrarre dalla roccia sorgente una quantità di fuso pari al 10-12 wt.%, per generare un residuo refrattario di densità equivalente alle peridotiti idrate. La differenziazione fra neosoma e paleosoma, prodotta dalla fusione parziale, può generare quindi una situazione di instabilità fra crosta e mantello, a causa del contrasto di densità fra le rocce poste a contatto. Per effetto di questa instabilità, possono verificarsi meccanismi duttili di trasferimento di massa, con inclusione di lenti di peridotiti all’interno della crosta, all’interfaccia fra lo slab continentale in subduzione ed il cuneo di mantello, ma anche, in caso di crosta inspessita, in corrispondenza della transizione crosta profonda-mantello litosferico (Moho) nella upper plate.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Welding is one of the most employed process for joining steel pipes. Although, manual welding is still the most used one, mechanized version and even automatized one have increased its demand. Thus, this work deals with girth welding of API 5L X65 pipes with 8” of nominal diameter and 8.0 mm thickness, beveled with V-30º narrow gap. Torch is moved by a bug carrier (mechanized welding) and further the parameters are controlled as a function of angular position (automatized welding). Welding parameters are presented for filling the joint with two-passes (root and filling/capping passes). Parameters for the root pass were extracted from previous author´s work with weldments carried out in plates, but validated in this work for pipe welding. GMAW processes were assessed with short-circuit metal transfer in both conventional and derivative modes using different technologies (RMD, STT and CMT). After the parameter determination, mechanical testing was performed for welding qualification (uniaxial tension, face and root bending, nick break, Charpy V-notch impact, microhardness and macrograph). The initially obtained results for RMD and CMT were acceptable for all testing and, in a second moment, also for the STT. However, weld beads carried out by using the conventional process failed and revealed the existence of lack of fusion, which required further parametrization. Thus, a Parameter-Variation System for Girth Welding (SVP) was designed and built to allow varying the welding parameters as a function of angular position by using an inclinometer. The parameters were set for each of the three angular positions (flat, vertical downhill and overhead). By using such equipment and approach, the conventional process with parameter variation allowed reducing the welding time for joint accomplishment of the order of 38% for the root pass and 30% for the filling/capping pass.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

No âmbito da saúde e farmacologia a procura de compostos para a prevenção e tratamento de doenças é constante, tendo sido valorizada atualmente a medicina tradicional aliada à existência de diversos compostos naturais provenientes de plantas, fungos e bactérias com ação anti-inflamatória e antimicrobiana. Logo é valorizada a investigação e estudos específicos das propriedades terapêuticas de compostos, dos mecanismos de ação e compreensão dos seus efeitos, úteis ao avanço da medicina. Posto isto, aliada à relevância do stresse oxidativo, associado a danos oxidativos e envolvimento em várias doenças humanas e no processo de envelhecimento, surge a necessidade de construção de uma ferramenta que permita estudar o efeito de drogas ao nível do stresse oxidativo, de modo a avaliar o potencial terapêutico, clarificar a respetiva função e abranger a aplicação de compostos que têm sido cada vez mais valorizados. Assim, foi delineado como objetivo o melhoramento genético de estripes Saccharomyces cerevisiae, de modo a promover a acumulação de drogas e, consequentemente promover as condições que despoletam a ação dos ativadores Yap1 e Msn2 ao nível do stresse oxidativo. Neste contexto, foi otimizada uma metodologia para a construção de novas estirpes haploides de S. cerevisiae com seis cruzamentos distintos que combinam a deleção independente de três transportadores diferentes (TxΔ, TyΔ e TzΔ) e, em simultâneo, cada um dos ativadores Yap1 e Msn2 em fusão com a Gfp (A-GFP). Estas estirpes haploides foram selecionadas por análises fenotípicas, confirmadas ao nível do genótipo pretendido por PCR e ensaios de microscopia de fluorescência quando sujeitas previamente ao tratamento com H2O2, que não só confirmou o genótipo A-GFP, como também permitiu avaliar qualitativamente a sensibilidade das estirpes ao H2O2 pela observação da localização nuclear da Gfp. No sentido de obter uma ferramenta simples de fácil manipulação e baixo custo que facilite a exposição de compostos e permanência no interior das células, de modo a potenciar o seu efeito a baixas concentrações e permitir uma análise mais assertiva, criou-se uma ferramenta que permitirá a caracterização de propriedades e efeitos pró-oxidantes e/ou antioxidantes de drogas ao nível do stresse oxidativo em levedura

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Cs atom beams, transversely collimated and cooled, passing through material masks in the form of arrays of reactive-ion-etched hollow Si pyramidal tips and optical masks formed by intense standing light waves, write submicron features on self-assembled monolayers (SAMs). Features with widths as narrow as 43 ± 6 nm and spatial resolution limited only by the grain boundaries of the substrate have been realized in SAMs of alkanethiols. The material masks write two-dimensional arrays of submicron holes; the optical masks result in parallel lines spaced by half the optical wavelength. Both types of feature are written to the substrate by exposure of the masked SAM to the Cs flux and a subsequent wet chemical etch. For the arrays of pyramidal tips, acting as passive shadow masks, the resolution and size of the resultant feature depends on the distance of the mask array from the SAM, an effect caused by the residual divergence of the Cs atom beam. The standing wave optical mask acts as an array of microlenses focusing the atom flux onto the substrate. Atom 'pencils' writing on SAMs have the potential to create arbitrary submicron figures in massively parallel arrays. The smallest features and highest resolutions were realized with SAMs grown on smooth, sputtered gold substrates.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

As estratégias de posicionamento são essenciais para o alcance de vantagem competitiva nos diferentes setores das atividades concorrenciais. O objetivo do trabalho está em investigar os discursos empregados pelos seis principais agentes envolvidos no processo de implantação da TV digital no Brasil e, concomitantemente, analisar e discutir os interesses de cada um desses agentes como participativos da decisão técnica/política da escolha do padrão de TV digital. Por intermédio de pesquisa exploratória de natureza qualitativa, análise pós-factum, com emprego da técnica de entrevista embasada na fusão de três referenciais teóricos relacionados ao posicionamento estratégico, especificamente, a Estratégia Decidida Continuamente, Nova Retórica e Análise Retórica, buscou-se delinear as diferentes etapas do processo que culminaram na outorga do padrão digital da TV brasileira em 02 de dezembro de 2007. A análise dos resultados da pesquisa aponta que a adoção do padrão japonês ocorreu em perfeita consonância com os interesses formados pela aliança dos Radiodifusores e do Governo Federal, em detrimento dos interesses do Coletivo Intervozes, da Indústria de Telecom e da Academia, sendo que, para a Indústria de Eletro-eletrônicos não houve interferências significativas no seu modelo de negócio. Esse caso constitui um instrutivo exemplo do processo de negociação no emprego das estratégias por parte dos executivos atuando como agentes retóricos na defesa dos interesses de suas respectivas organizações.