Experimental studies and phase field modeling of microstructure evolution during solidification with electromagnetic stirring

Thixocasting requires manufacturing of billets with non-dendritic microstructure. Aluminum alloy A356 billets were produced by rheocasting in a mould placed inside a linear electromagnetic stirrer. Subsequent heat treatment was used to produce a transition from rosette to globular microstructure. The current and the duration of stirring were explored as control parameters. Simultaneous induction heating of the billet during stirring was quantified using experimentally determined thermal profiles. The effect of processing parameters on the dendrite fragmentation was discussed. Corresponding computational modeling of the process was performed using phase-field modeling of alloy solidification in order to gain insight into the process of morphological changes of a solid during this process. A non-isothermal alloy solidification model was used for simulations. The morphological evolution under such imposed thermal cycles was simulated and compared with experimentally determined one. Suitable scaling using the thermosolutal diffusion distances was used to overcome computational difficulties in quantitative comparison at system scale. The results were interpreted in the light of existing theories of microstructure refinement and globularisation.

An online-implementable differential evolution tuned all-aspect guidance law

This paper proposes a differential evolution based method of improving the performance of conventional guidance laws at high heading errors, without resorting to techniques from optimal control theory, which are complicated and suffer from several limitations. The basic guidance law is augmented with a term that is a polynomial function of the heading error. The values of the coefficients of the polynomial are found by applying the differential evolution algorithm. The results are compared with the basic guidance law, and the all-aspect proportional navigation laws in the literature. A scheme for online implementation of the proposed law for application in practice is also given. (c) 2010 Elsevier Ltd. All rights reserved.

A MAS NMR investigation of aluminosilicate, silicophosphate, and aluminosilicophosphate gels and the evolution of crystalline structures on heating the gels

Gels of various composition containing SiO2, Al2O3, and P2O5 have been investigated by employing high resolution magic-angle-spinning (MAS) 27Al, 29Si, and 31P NMR spectroscopy. Changes occurring in the NMR spectra as the gels are progressively heated have been examined to understand the nature of structural changes occurring during the crystallization of the gels. 27Al resonance is sensitive to changes in the coordination number even when the Al concentration is as low as 1 mol%. As the percentage of Al increases, the hydroxyl groups tend to be located on the Al sites while Si remains as SiO4/2 (Q4). Mullite is the major phase formed at higher temperature in the aluminosilicate gels. In the case of the silicophosphate gels, Si is present in the form of Q4 and Q3 species. There is a change in the coordination of Si from four to six as the gel is heated. The formation of six-coordinated Si is facilitated even at lower temperatures (~673 K) when the P2O5 content is high. The phosphorus atoms present as orthophosphoric acid units in the xerogels change over to metaphosphate-like units as the gel is heated to higher temperatures. In aluminosilicophosphates, Si is present as Q4 and Q3 species while P is present as metaphosphate units; Al in these gels seems to be inducted into the tetrahedral network positions.

Effect of Strain Rate on Evolution of the Deformation Microstructure and Texture in Polycrystalline Copper and Nickel

The evolution of crystallographic texture in polycrystalline copper and nickel has been studied. The deformation texture evolution in these two materials over seven orders of magnitude of strain rate from 3 x 10(-4) to similar to 2.0 x 10(+3) s(-1) show little dependence on the stacking fault energy (SFE) and the amount of deformation. Higher strain rate deformation in nickel leads to weakerh < 101 > texture because of extensive microband formation and grain fragmentation. This behavior, in turn, causes less plastic spin and hence retards texture evolution. Copper maintains the stable end < 101 > component over large strain rates (from 3 x 10(-4) to 10(+2) s(-1)) because of its higher strain-hardening rate that resists formation of deformation heterogeneities. At higher strain rates of the order of 2 x 10(+3) s(-1), the adiabatic temperature rise assists in continuous dynamic recrystallization that leads to an increase in the volume fraction of the < 101 > component. Thus, strain-hardening behavior plays a significant role in the texture evolution of face-centered cubic materials. In addition, factors governing the onset of restoration mechanisms like purity and melting point govern texture evolution at high strain rates. SFE may play a secondary role by governing the propensity of cross slip that in turn helps in the activation of restoration processes.

Late Pleistocene and Holocene environmental evolution of the Murchisonfjorden area, Nordaustlandet, Svalbard

The purpose of this study was to establish the palaeoenvironmental conditions during the late Quaternary in Murchisonfjorden, Nordaustlandet, based on foraminiferal assemblage compositions, and to determine the onset and termination of the Weichselian glaciations. The foraminiferal assemblage compositions were studied in marine sediments from three different archives, from sections next to the present shoreline in the Bay of Isvika, from a core in the Bay of Isvika and from a core from Lake Einstaken. OSL and AMS 14C age determinations were performed on samples from the three archives, and the results show deposition of marine sediments during ice-free periods of the Early Weichselian, the Middle Weichselian and the Late Weichselian, as well as during the Holocene in the investigated area. Marine sediments from the Early and Middle Weichselian were sampled from isostatically uplifted sections along the present shoreline.Sediments from the transition from the Late Weichselian to early Holocene time intervals were found in the bottom of the core from Lake Einstaken. Holocene sediments were investigated in the sections and in the core from the Bay of Isvika. The marine sediments from the sections are comprised of five benthic foraminiferal assemblages. The Early Weichselian is represented by two foraminiferal assemblages, the Middle Weichselian, the early and the late Holocene each by one. All five foraminiferal assemblages were deposited in glacier-distal shallow-water environments, which had a connection to the open ocean. Changes in the composition of the assemblages can be ascribed to differences in the bottom-water currents and changes in the salinity. The Middle Weichselian assemblage is of special importance, because it is the first foraminiferal assemblage to be described from this time interval from Svalbard. Four benthic foraminiferal assemblages were deposited shortly before the marine to lacustrine transition at the boundary between the Late Weichselian and Holocene in Lake Einstaken. The foraminiferal assemblages show a change from a high-arctic, normal marine shallow-water environment to an even shallower environment with highly fluctuating salinity. The analyses of the core from 100 m water depth in the Bay of Isvika resulted in the determination of four foraminiferal assemblages. These indicated changes from a glacier-proximal environment during deglaciation, to a more glacier-distal environment during the Early Holocene. This was followed by a period with a marked change to a considerably cooler environment and finally to a closed fjord environment in the middle and late Holocene times. Additional sedimentological analyses of the marine and glacially derived sediments from the uplifted sections, as well as observations of multiple striae on the bedrock, observations of deeply weathered bedrock and findings of tills interlayered with marine sediments complete the investigations in the study area. They indicate weak glacial erosion in the study area. It can be concluded that marine deposition occurred in the investigated area during three time intervals in the Weichselian and during most of the Holocene. The foraminiferal assemblages in the Holocene are characterized by a transition from glacier-proximal to glacier-distal faunas. The palaeogeographical change from an open fjord to a closed fjord environment is a result of the isostatic uplift of the area after the LGM and is clearly reflected in the foraminiferal assemblages. Another influencing factor on the foraminiferal assemblage composition are changes in the inflow of warmer Atlantic waters to the study area.

Evolution of polyembryony: Consequences to the fitness of mother and offspring

Polyembryony, referring here to situations where a nucellar embryo is formed along with the zygotic embryo, has different consequences for the fitness of the maternal parent and offspring. We have developed genetic and inclusive fitness models to derive the conditions that permit the evolution of polyembryony under maternal and offspring control. We have also derived expressions for the optimal allocation (evolutionarily stable strategy, ESS) of resources between zygotic and nucellar embryos. It is seen that (i) Polyembryony can evolve more easily under maternal control than under that of either the offspring or the ‘selfish’ endosperm. Under maternal regulation, evolution of polyembryony can occur for any clutch size. Under offspring control polyembryony is more likely to evolve for high clutch sizes, and is unlikely for low clutch sizes (<3). This conflict between mother and offspring decreases with increase in clutch size and favours the evolution of polyembryony at high clutch sizes, (ii) Polyembryony can evolve for values of “x” (the power of the function relating fitness to seed resource) greater than 0.5758; the possibility of its occurrence increases with “x”, indicating that a more efficient conversion of resource into fitness favours polyembryony. (iii) Under both maternal parent and offspring control, the evolution of polyembryony becomes increasingly unlikely as the level of inbreeding increases, (iv) The proportion of resources allocated to the nucellar embryo at ESS is always higher than that which maximizes the rate of spread of the allele against a non-polyembryonic allele.Finally we argue that polyembryony is a maternal counter strategy to compensate for the loss in her fitness due to brood reduction caused by sibling rivalry. We support this assertion by two empirical evidences: (a) the extent of polyembryony is positively correlated with brood reduction inCitrus, and (b) species exhibiting polyembryony are more often those that frequently exhibit brood reduction.

Seasonal variation in the onset of egg laying in a primitively eusocial wasp: implications for the evolution of sociality

When freshly eclosed females of the primitively eusocial wasp, Rapalidia marginata are isolated into individual cages, only about half of them build nests and lay eggs and those that do so take a long and variable amount of time (Mean +/- SD = 66 +/- 37 days) before they lay their first egg. Part of the reason for this delay is because, when kept in isolation, no wasp begins to lay eggs during a period of approximately 82 days from mid - October to early January. Wasps maintained at a constant temperature of 26 +/- 1-degrees-C however initiate egg laying throughout the year, suggesting that the low temperatures during mid - October to early January may be at least one factor that makes this period unfavourable for wasps maintained at room temperature. Egg laying continues more or less normally throughout October-January however, in all natural and laboratory colonies studied. Natural colonies of R. marginata are initiated throughout the year and often by groups of females. Huddling together is a striking feature of the wasps especially on cold mornings. We therefore suggest that the isolated animals in our experiment are unable to lay eggs during the coldest part of the year because of their inability to huddle together, share metabolic heat and perform "co-operative thermoregulation". Such "co-operative thermoregulation" may thus be another factor that facilitates the evolution of socialitly.

Historical considerations and evolution of the forest policies for small woodlot owners of Quebec.

XVIII IUFRO World Congress, Ljubljana 1986.

Precursor Dependent Microstructure Evolution and Nonstoichiometry in Nanostructured Cerium Oxide Coatings Using the Solution Precursor Plasma Spray Technique

A solution precursor plasma spray (SPPS) technique has been used for direct deposition of cerium oxide nanoparticles (CNPs) from various cerium salt solutions as precursors. Solution precursors were injected into the hot zone of a plasma plume to deposit CNP coatings. A numerical study of the droplet injection model has been employed for microstructure development during SPPS. The decomposition of each precursor to cerium oxide was analyzed by thermogravimetric-differential thermal analysis and validated by thermodynamic calculations. The presence of the cerium oxide phase in the coatings was confirmed by X-ray diffraction studies. Transmission electron microscopy studies confirmed nanocrystalline (grain size <14 nm) characteristic of the coatings. X-ray photoelectron spectroscopy studies indicated the presence of a high concentration of Ce3+ (up to 0.32) in the coating prepared by SPPS. The processing and microstructure evolution of cerium oxide coatings with high nonstoichiometry are reported.

Transposable element-medicated evolution of sex: A population genetic model

For a population made up of individuals capable of sexual as well as asexual modes of reproduction, conditions for the spread of a transposable element are explored using a one-locus, two-haplotype model. The analysis is then extended to include the possibility that the transposable element can modulate the probability of sexual reproduction, thus casting Hickey’s (1982,Genetics 101: 519–531) suggestion in a population genetics framework. The model explicitly includes the cost of sexual reproduction, fitness disadvantage to the transposable element, probability of transposition, and the predisposition for sexual reproduction in the presence and absence of the transposable element. The model predicts several kinds of outcome, including initial frequency dependence and stable polymorphism. More importantly, it is seen that for a wide range of parameter values, the transposable element can go to fixation. Therefore it is able to convert the population from a predominantly asexual to a predominantly sexual mode of reproduction. Viewed in conjunction with recent results implicating short stretches of apparently non-coding DNA in sex determination (McCoubreyet al. 1988,Science 242: 1146–1151), the model hints at the important role this mechanism could have played in the evolution of sexuality.

The evolution of genomic imprinting

We explore three possible pathways for the evolution of genomic imprinting. (1) Imprinting may be advantageous in itself when imprinted and unimprinted alleles of a locus confer different phenotypes. If a segment of DNA is imprinted in the gametes of one sex but not in those of the other, it might lead to effects correlated with sexual dimorphism. More fundamentally, in certain organisms, sex determination might have evolved because of imprinting. When imprinting leads to chromosome elimination or inactivation and occurs in some embryos but not in others, two classes of embryos, differing in the number of functional gene copies, would result. A model for sex determination based on inequality in the actual or effective copy-number of particular noncoding, regulatory sequences of DNA has been proposed (Chandra, Proc. natn. Acad. Sci. U.S.A. 82. 1165–1169 and 6947–6949, 1985). Maternal control of offspring sex is another possible consequence of imprinting; this would indicate a potential role for imprinting in sex ratio evolution. (2) Genes responsible for imprinting may have pleiotropic effects and they may have been selected for reasons other than their imprinting ability. Lack of evidence precludes further consideration of this possibility. (3) Imprinting could have co-evolved with other traits. For instance, gamete-specific imprinting could lead to a lowered fitness of androgenetic or gynogenetic diploids relative to the fitness of ‘normal’ diploids. This in turn would reinforce the evolution of anisogamy. The reversibility of imprinting raises the possibility of occasional incomplete or improper erasure. If the site of imprinting is the egg – as appears to be the case with the human X (Chandra and Brown, Nature 253. 165–168, 1975) – either improper imprinting or improper erasure could lead to unusual patterns of inheritance (as in the fragile-X syndrome) or fitness effects skipping generations.

Evolution of and preconditions for generation of corrugations on a plane surface in rolling contact

A hard roller under normal load is driven by the flat surface of a soft disc. Corrugations are generated on the disc when certain surface morphological, load, speed and mechanical property-oriented conditions are met. The evolutionary process of corrugation generation and the preconditions necessary for it are investigated morphologically and mechanically for four disc materials: mild steel, brass, PTFE and PMMA.

Evolution in the time series of vortex velocity fluctuations across different regimes of vortex flow

Investigations of vortex velocity fluctuation in time domain have revealed a presence of low frequency velocity fluctuations which evolve with the different driven phases of the vortex state in a single crystal of 2H-NbSe2. The observation of velocity fluctuations with a characteristic low frequency is associated with the onset of nonlinear nature of vortex flow deep in the driven elastic vortex state. (C) 2009 Elsevier B.V. All rights reserved.

Temperature dependence of hydrogen evolution reaction on nickel oxide electrode in sealed nickel/cadmium cells

The impedance of sealed nickel/cadmium cells around a cell e.m.f. of 0.0 V was measured at five different temperatures between � 10 and +30 °C. The results show that the behaviour is similar at all temperatures. Based on the experimental results, the relation between charge-transfer resistance (Rct) and temperature (T) has been established for the Volmer reaction. Further, the value of cathodic transfer coefficient (?) has been estimated.