Analysis of the four wave mixing effect (FWM) in a dispersion decreasing fiber (DDF) for a WDM system

We did a numerical investigation of the propagation of short light pulses in the region of 1.55 mu m and the conversion efficiency (CE) for the four wave mixing generation (FWM) of ordinary and dispersion decreasing fibers for use in wavelength division multiplexing (WDM) systems, Our simulations studies three different profiles, linear, hyperbolic. and constant, One conclude that for all the profiles there is decrease of the conversion efficiency with the increase in the channel separation. The hyperbolic profile present a higher efficiency of around 1000 above in magnitude compared with the others profiles at 0.2 nm of channel separation. We calculate the conversion efficiency versus the fiber length for the three profiles. The conversion efficiency for the hyperbolic profile is higher when compared to the constant and linear profiles. The other interesting point of the hyperbolic profile is that the increase of the CE in the beginning of the fiber does not show my oscillation in the CE value (log eta), which was observed for the constant and linear profiles. For all the profiles there is an increase of the conversion efficiency with the increase of the pump power. The compression factor C-i for the generated FWM signal at omega(3) was measured along the DDF's and the constant profile fibers. One can conclude that with the use of decreasing dispersion profile (DDF) fibers one can have a control of the (CE) conversion efficiency and the compression factor of the four wave mixing (FWM) generation in WDM systems. (c) 2005 Elsevier B.V. All rights reserved.

Motion compensation with minimal residue dispersion matching criteria

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Tecnoloigia, 2016.

Rheological Properties of a Sodium Bentonite and Lactose Aqueous Dispersion

Aim of this paper is show the viscosity measure of a sodium bentonite-water-lactose mixture and your rheological behaviour. This analysis showed the formation of tridimensional structure type and formation of stratified silicate/lactose, this occurred due to different concentrations of organic products into mixture and due to a difference of rotation during viscosity measument. Formation of networks is a consequence of the attraction between the silicate layers in water-lactose mixture. In the present work aqueous solutions of lactose with concentration of 7%, 5%, 3%, 1% and 0% (wt %) were used.

Dynamics and Heterogeneity of Pb(II) Binding by SiO2 Nanoparticles in an Aqueous Dispersion

Pb(II) binding by SiO2 nanoparticles in an aqueous dispersion was investigated under conditions where the concentrations of Pb2+ ions and nanoparticles are of similar magnitude. Conditional stability constants (log K) obtained at different values of pH and ionic strength varied from 4.4 at pH 5.5 and I = 0.1 M to 6.4 at pH 6.5 and I = 0.0015 M. In the range of metal to nanoparticle ratios from 1.6 to 0.3, log K strongly increases, which is shown to be due to heterogeneity in Pb(II) binding. For an ionic strength of 0.1 M the Pb2+/SiO2 nanoparticle system is labile, whereas for lower ionic strengths there is loss of lability with increasing pH and decreasing ionic strength. Theoretical calculations on the basis of Eigen-type complex formation kinetics seem to support the loss of lability. This is related to the nanoparticulate nature of the system, where complexation rate constants become increasingly diffusion controlled. The ion binding heterogeneity and chemodynamics of oxidic nanoparticles clearly need further detailed research.

Modélisation hydro-sédimentaire de la rade de Toulon : application à l’étude de la dispersion de radionucléides

L’objectif de ce travail est mettre en place un modèle hydro-sédimentaire de dispersion des radionucléides, comme outil d’aide à la décision suite à une hypothétique contamination marine accidentelle. Appliqué à la Rade de Toulon, il utilise le modèle MARS-3D pour l’étude hydrodynamique et le module MIXSED pour la dynamique des différentes classes de sédiments. Les cas d’application présentés concernent le césium et le plutonium, qui ont des affinités très différentes avec les sédiments fins. Les simulations de rejet, effectuées en fond de baie, montrent une variabilité saisonnière marquée, due aux conditions météorologiques typiques, mais aussi aux conditions de débit et de charge sédimentaire associée du fleuve Las, qui se jette dans la Rade. Ainsi, les simulations par forts vents, qui favorisent la circulation et les échanges de masses d’eau, présentent une diminution rapide des activités dissoutes. Par ailleurs, le Vent d’Est hivernal, qui engendre d’importantes crues du Las et un apport de sédiments à la Rade, favorise le piégeage des radionucléides dans les sédiments de fond, où les deuxtiers de la contamination initiale sont piégés après une simulation de deux mois.

Dispersion and optimization of a calcium sulfoaluminate mortar prepared with superplasticizer

Calcium sulfoaluminate (CSA) cements/mortars are receiving increasing attention since their manufacture produces less CO2 than ordinary Portland cement (OPC) (up to 22% of decrease depending on its composition). These systems are complex and there are many parameters affecting their hydration mechanism, such as water-to-cement (w/c) ratio, type and amount of sulfate source, and so on. Low w/c ratios, within certain limits, may reduce the porosity and consequently, improve the mechanical strengths. However, it is accompanied by an increasing of viscosity and lack of both workability and homogeneity, with the consequent negative effect on the mechanical properties. The dispersion of the particles through the adsorption of the right amount and type of additives, such as superplasticizers, is a key point to improve the workability of mortars allowing both the preparation of homogeneous mixtures and the reduction of the amount of mixing water. This work deals with the preparation and optimization of homogeneous CSA-mortars with improved mechanical strengths. The optimum amount of superplasticizer was optimized through rheological measurements. The effect of different amounts of the superplasticizer on the viscosity of the mortars, its hydration mechanism and corresponding mechanical properties has been studied and will be discussed.

REGULATION OF SHAPE DYNAMICS AND ACTIN POLYMERIZATION DURING COLLECTIVE CELL MIGRATION

This thesis aims to understand how cells coordinate their motion during collective migration. As previously shown, the motion of individually migrating cells is governed by wave-like cell shape dynamics. The mechanisms that regulate these dynamic behaviors in response to extracellular environment remain largely unclear. I applied shape dynamics analysis to Dictyostelium cells migrating in pairs and in multicellular streams and found that wave-like membrane protrusions are highly coupled between touching cells. I further characterized cell motion by using principle component analysis (PCA) to decompose complex cell shape changes into a serial shape change modes, from which I found that streaming cells exhibit localized anterior protrusion, termed front narrowing, to facilitate cell-cell coupling. I next explored cytoskeleton-based mechanisms of cell-cell coupling by measuring the dynamics of actin polymerization. Actin polymerization waves observed in individual cells were significantly suppressed in multicellular streams. Streaming cells exclusively produced F-actin at cell-cell contact regions, especially at cell fronts. I demonstrated that such restricted actin polymerization is associated with cell-cell coupling, as reducing actin polymerization with Latrunculin A leads to the assembly of F-actin at the side of streams, the decrease of front narrowing, and the decoupling of protrusion waves. My studies also suggest that collective migration is guided by cell-surface interactions. I examined the aggregation of Dictyostelim cells under distinct conditions and found that both chemical compositions of surfaces and surface-adhesion defects in cells result in altered collective migration patterns. I also investigated the shape dynamics of cells suspended on PEG-coated surfaces, which showed that coupling of protrusion waves disappears on touching suspended cells. These observations indicate that collective migration requires a balance between cell-cell and cell-surface adhesions. I hypothesized such a balance is reached via the regulation of cytoskeleton. Indeed, I found cells actively regulate cytoskeleton to retain optimal cell-surface adhesions on varying surfaces, and cells lacking the link between actin and surfaces (talin A) could not retain the optimal adhesions. On the other hand, suspended cells exhibited enhanced actin filament assembly on the periphery of cell groups instead of in cell-cell contact regions, which facilitates their aggregation in a clumping fashion.

UHMWPE/SBA-15 nanocomposites synthesized by in situ polymerization

Different nanocomposites have been attained by in situ polymerization based on ultra-high molecular weight polyethylene (UHMWPE) and mesoporous SBA-15, this silica being used for immobilization of the FI catalyst bis [N-(3-tert-butylsalicylidene)-2,3,4,5,6-pentafluoroanilinato] titanium (IV) dichloride and as filler as well. Two distinct approaches have been selected for supporting the FI catalyst on the SBA-15 prior polymerization. A study on polymerization activity of this catalyst has been performed under homogenous conditions and upon heterogenization. A study of the effect of presence of mesoporous particles and of the immobilization method is also carried out. Moreover, the thermal characterization, phase transitions and mechanical response of some pristine UHMWPEs and UHMWPE/SBA-15 materials have been carried out. Relationships with variations on molar mass, impregnation method of catalyst and final SBA-15 content have been established.

Hybrid materials based on polyethylene and MCM-41 microparticles functionalized with silanes: catalytic aspects of in situ polymerization, crystalline features and mechanical properties

New nanocomposites based on polyethylene have been prepared by in situ polymerization of ethylene in presence of mesoporous MCM-41. The polymerization reactions were performed using a zirconocene catalyst either under homogenous conditions or supported onto mesoporous MCM-41 particles, which are synthesized and decorated post-synthesis with two silanes before polymerization in order to promote an enhanced interfacial adhesion. The existence of polyethylene chains able to crystallize within the mesoporous channels in the resulting nanocomposites is figured out from the small endothermic process, located at around 80 C, on heating calorimetric experiments, in addition to the main melting endotherm. These results indicate that polyethylene macrochains can grow up during polymerization either outside or inside the MCM-41 channels, these keeping their regular hexagonal arrangements. Mechanical response is observed to be dependent on the content in mesoporous MCM-41 and on the crystalline features of polyethylene. Accordingly, stiffness increases and deformability decreases in the nanocomposites as much as MCM-41 content is enlarged and polyethylene amount within channels is raised. Ultimate mechanical performance improves with MCM-41 incorporation without varying the final processing temperature.

Joint dispersion model with a flexible link

Poster presented at the Workshop on Flexible Models for Longitudinal and Survival Data with Applications in Biostatistics. University of Warwick, Coventry, UK, 27-29 July 2015

Survival analysis with internal covariates modelled using a longitudinal dispersion model and flexible links

Poster presented at the From Basic Sciences to Clinical Research: 1st International Congress of CiiEM. Egas Moniz, Caparica, Portugal, 27-28 November 2015

Non-parametrized functionals with empirical dispersion corrections: A happy match?

The performances of two parametrized functionals (namely B3LYP and B2PYLP) have been compared with those of two non-parametrized functionals (PBE0 and PBE0-DH) on a relatively large benchmark set when three different types of dispersion corrections are applied [namely the D2, D3 and D3(BJ) models]. Globally, the MAD computed using non-parametrized functionals decreases when adding dispersion terms although the accuracy not necessarily increases with the complexity of the model of dispersion correction used. In particular, the D2 correction is found to improve the performances of both PBE0 and PBE0-DH, while no systematic improvement is observed going from D2 to D3 or D3(BJ) corrections. Indeed when including dispersion, the number of sets for which PBE0-DH is the best performing functional decreases at the benefit of B2PLYP. Overall, our results clearly show that inclusion of dispersion corrections is more beneficial to parametrized double-hybrid functionals than to non-parametrized ones. The same conclusions globally hold for the corresponding global hybrids, showing that the marriage between non-parametrized functionals and empirical corrections may be a difficult deal.