Levels, sources and seasonality of coarse particles (PM10-PM2.5) in three European capitals e implications for particulate pollution control

Coarse particles of aerodynamic diameter between 2.5 and 10 mm (PMc) are produced by a range of natural (windblown dust and sea sprays) and anthropogenic processes (non-exhaust vehicle emissions, industrial, agriculture, construction and quarrying activities). Although current ambient air quality regulations focus on PM2.5 and PM10, coarse particles are of interest from a public health point of view as they have been associated with certain mortality and morbidity outcomes. In this paper, an analysis of coarse particle levels in three European capitals (London, Madrid and Athens) is presented and discussed. For all three cities we analysed data from both traffic and urban background monitoring sites. The results showed that the levels of coarse particles present significant seasonal, weekly and daily variability. Their wind driven and non-wind driven resuspension as well as their roadside increment due to traffic were estimated. Both the local meteorological conditions and the air mass history indicating long-range atmospheric transport of particles of natural origin are significant parameters that influence the levels of coarse particles in the three cities especially during episodic events.

Renewable energy infrastructure. A challenge for Venezuelan industrial construction

The relevance of renewable energy has grown significantly in our global society. Important efforts are oriented to sustain it. Renewable energy depends on different technical, financial environmental and social complex processes. From the point of view of industrial construction sector this research evaluates some of the current trends in energy generation and use in Venezuela as well as environmental consequences and risks that derive from these. Additionally, authors highlight the importance of infrastructure as key issue to sustain renewable energy generation and use. The study present references of some energy renewable projects in process in Venezuela and the main problems that constrain their performance. Conclusions evidence the complex nature of industrial construction and suggest the need to improve industrial construction competitivenes as a strategy oriented to enhance renewable energy offer in the country. Additionally it is proposed to all stakeholders to work toghether to correct the conditions that currently limit industrial construction development. This is part of ongoing research.

Los agentes de la edificación desde el punto de vista de la Gestión Integral de Proyectos: diferencias y semejanzas entre la Legislación Española y los Estándares Internacionales = Expert agents in the Global Development of a building project: differences and similarities between Spanish and International contexts.

Desde los años 60, crece en Europa y Estados Unidos la preocupación y la necesidad de mejorar los procesos de gerencia de los proyectos de construcción al volverse estos más complejos. Esto ha llevado a la continua aparición de nuevos profesionales desde la fecha citada hasta nuestros días. De ahí la complejidad de conocer las cualidades de cada uno de ellos, así como las funciones a realizar o la formación que deben tener para poder desarrollar el puesto de trabajo según el papel que desempeñan para cada actividad. Muchos agentes son los que pueden intervenir en la edificación, muchas son las funciones que llevan a cabo estos agentes, muchas son las habilidades que se necesitan para realizar estas misiones, y una buena gestión de la edificación es la que hay que desarrollar para lograr el gran éxito. El presente trabajo fin de máster, dirigido a arquitectos, arquitectos técnicos, ingenieros, abogados, economistas y todos los profesionales del sector inmobiliario y de la construcción, trata de resolver todas aquellas dudas sobre los diferentes sujetos que estarán presentes desde la definición del proyecto en la fase inicial hasta el final de la obra, pasando por las fases de pre-construcción, construcción y post-construcción. (ENGLISH VERSION) Since the 1960s, most construction projects have become more and more complex, and new concerns and necessities related to the management of a project have been on the rise in Europe and in the United States. Thence, the need for more specialized professionals in the field has become a common fact, as well as the inclusion of new curricular subjects in most building engineering studies. There are different agents that play a relevant role in a building project; some of them are expected to perform a highly specialized set of functions that require specific management skills for the work to be successful. This research work—aimed mainly at engineers, quantity surveyors, lawyers, economists, real estate and construction professionals—shows the major implications of the building construction process including both pre-tender/construction and post-tender/construction stages as far as the main expert agents are involved.

Ventilation system design and large scale fire tests

The design, construction and operation of the tunnels of M-30, the major ring road in the city of Madrid (Spain), represent a very interesting project in wich a wide variety of situations -geometrical, topographical, etc.- had to be covered, in variable conditions of traffic. For that reasons, the M-30 project is a remarkable technical challenge, which, after its completion, turned into an international reference. From the "design for safety" perspective, a holistic approach has been used to deal with new technologies, integration of systems and development of the procedures to reach the maximum level. However, one of the primary goals has been to achieve reasonable homogeneity characteristics which can permit operate a netword of tunels as one only infraestructure. In the case of the ventilation system the mentioned goals have implied innovative solutions and coordination efforts of great interest. Consequently, this paper describes the principal ideas underlying the conceptual solution developed focusing on the principal peculiarities of the project.

Survey on integration of Applied Geology and Geomorphology in Civil Engineering curricula in the framework of the European Higher Education Area (EHEA) by using practical trips

The engineer must have sufficient theoretical knowledge to be applied to solve specific problems, with the necessary capacity to simplify these approaches, and taking into account factors such as speed, simplicity, quality and economy. In Geology, its ultimate goal is the exploration of the history of the geological events through observation, deduction, reasoning and, in exceptional cases by the direct underground exploration or experimentation. Experimentation is very limited in Geology. Reproduction laboratory of certain phenomena or geological processes is difficult because both time and space become a large scale. For this reason, some Earth Sciences are in a nearly descriptive stage whereas others closest to the experimental, Geophysics and Geochemistry, have assimilated progress experienced by the physics and chemistry. Thus, Anglo-Saxon countries clearly separate Engineering Geology from Geological Engineering, i.e. Applied Geology to the Geological Engineering concepts. Although there is a big professional overlap, the first one corresponds to scientific approach, while the last one corresponds to a technological one. Applied Geology to Engineering could be defined as the Science and Applied Geology to the design, construction and performance of engineering infrastructures in and field geology discipline. There has been much discussion on the primacy of theory over practice. Today prevails the exaggeration of practice, but you get good workers and routine and mediocre teachers. This idea forgets too that teaching problem is a problem of right balance. The approach of the action lines on the European Higher Education Area (EHEA) framework provides for such balance. Applied Geology subject represents the first real contact with the physical environment with the practice profession and works. Besides, the situation of the topic in the first trace of Study Plans for many students implies the link to other subjects and topics of the career (tunnels, dams, groundwater, roads, etc). This work analyses in depth the justification of such practical trips. It shows the criteria and methods of planning and the result which manifests itself in pupils. Once practical trips experience developed, the objective work tries to know about results and changes on student’s motivation in learning perspective. This is done regardless of the outcome of their knowledge achievements assessed properly and they are not subject to such work. For this objective, it has been designed a survey about their motivation before and after trip. Survey was made by the Unidad Docente de Geología Aplicada of the Departamento de Ingeniería y Morfología del Terreno (Escuela Técnica Superior de Ingenieros de Caminos, Canales y Puertos, Universidad Politécnica de Madrid). It was completely anonymous. Its objective was to collect the opinion of the student as a key agent of learning and teaching of the subject. All the work takes place under new teaching/learning criteria approach at the European framework in Higher Education. The results are exceptionally good with 90% of student’s participation and with very high scores in a number of questions as the itineraries, teachers and visited places (range of 4.5 to 4.2 in a 5 points scale). The majority of students are very satisfied (average of 4.5 in a 5 points scale).

Seismic Risk Scenarios in Puerto Principe (Haiti). A Tool for Reconstruction and Emergency Planning

The 12 January 2010, an earthquake hit the city of Port-au-Prince, capital of Haiti. The earthquake reached a magnitude Mw 7.0 and the epicenter was located near the town of Léogâne, approximately 25 km west of the capital. The earthquake occurred in the boundary region separating the Caribbean plate and the North American plate. This plate boundary is dominated by left-lateral strike slip motion and compression, and accommodates about 20 mm/y slip, with the Caribbean plate moving eastward with respect to the North American plate (DeMets et al., 2000). Initially the location and focal mechanism of the earthquake seemed to involve straightforward accommodation of oblique relative motion between the Caribbean and North American plates along the Enriquillo-Plantain Garden fault system (EPGFZ), however Hayes et al., (2010) combined seismological observations, geologic field data and space geodetic measurements to show that, instead, the rupture process involved slip on multiple faults. Besides, the authors showed that remaining shallow shear strain will be released in future surface-rupturing earthquakes on the EPGFZ. In December 2010, a Spanish cooperation project financed by the Politechnical University of Madrid started with a clear objective: Evaluation of seismic hazard and risk in Haiti and its application to the seismic design, urban planning, emergency and resource management. One of the tasks of the project was devoted to vulnerability assessment of the current building stock and the estimation of seismic risk scenarios. The study was carried out by following the capacity spectrum method as implemented in the software SELENA (Molina et al., 2010). The method requires a detailed classification of the building stock in predominant building typologies (according to the materials in the structure and walls, number of stories and age of construction) and the use of the building (residential, commercial, etc.). Later, the knowledge of the soil characteristics of the city and the simulation of a scenario earthquake will provide the seismic risk scenarios (damaged buildings). The initial results of the study show that one of the highest sources of uncertainties comes from the difficulty of achieving a precise building typologies classification due to the craft construction without any regulations. Also it is observed that although the occurrence of big earthquakes usually helps to decrease the vulnerability of the cities due to the collapse of low quality buildings and the reconstruction of seismically designed buildings, in the case of Port-au-Prince the seismic risk in most of the districts remains high, showing very vulnerable areas. Therefore the local authorities have to drive their efforts towards the quality control of the new buildings, the reinforcement of the existing building stock, the establishment of seismic normatives and the development of emergency planning also through the education of the population.

Energy consumption and intensity of toll highway transport in Spain

We estimate the energy consumption of toll highway transport on a number of Spanish roads. Regression parameters are balanced according to coefficients from an empirical analysis based on survey data by vehicle type. The mean energy consumption and subsequent CO2 emissions on the toll highway sections are estimated as 1895 MJ/h/lane-km and 0.15 tCO2 eq./h/lane-km, values that increase to 2644 and 0.22 when energy and carbon emissions of transport infrastructure are considered based on the life cycle energy consumption for toll highway construction and use. If the energy intensity of infrastructure construction is allocated to the users according to traffic, it is much higher for motorcycles than for cars, and is significantly lower for articulated trucks than for vans.

Storage stability of SBS/sulfur modified bitumens at high temperature: influence of bitumen composition and structure

Polymer modified bitumens, PMBs, are usually prepared at high temperature and subsequently stored for a period of time, also at high temperature. The stability of PMBs, in these conditions, has a decisive influence in order to obtain the adequate performances for practical applications. In this article the attention is focused in the analysis of the factors that determine the stability of styrene–butadiene–styrene copolymer (SBS)/sulfur modified bitumens when the mixtures are maintained at high temperature. Bitumens from different crude oil sources were used to prepare SBS/sulfur modified bitumens. Changes in the values of viscosity, softening point, as well as in the morphology of PMB samples, stored at 160 °C, were related to the bitumen chemical composition and to the amount of asphaltene micelles present in the neat bitumen used in their preparation El trabajo se centra en el estudio de la influencia de la estructura /composición del betún sobre la compatibilidad del sistema betún/SBS. Cuatro betunes provenientes de dos crudos distintos se seleccionaron y sus mezclas se utilizaron para preparar betunes modificados con contenidos de SBS del 3% en peso

Quantity of CO2 Emissions in the Life Cycle of a Highway Infrastructure.

The complexity of climate change and its evolution during the last few years has a positive impact on new developments and approaches to reduce the emissions of CO2. Looking for a methodology to evaluate the sustainability of a roadway, a tool has been developed. Life Cycle Assessment (LCA) is being accepted by the road industry to measure and evaluate the environmental impacts of an infrastructure, as the energy consumption and carbon footprint. This paper describes the methodology to calculate the CO2 emissions associated with the energy embodied on a roadway along its life cycle, including construction, operations and demolition. It will assist to find solutions to improve the energy footprint and reduce the amount of CO2 emissions. Details are provided of both, the methodology and the data acquisition. This paper is an application of the methodology to the Spanish highways, using a local database. Two case studies and a practical example are studied to show the model as a decision support for sustainable construction in the road industry.

Technical evolution of 3d modular construction from the nineteenth century to world war II

3D Modular construction is poorly known and scarcely published in technical literature. In spite of that there are an increasing number of manufacturers offering their products in different countries. This method has largely evolved from early examples such as the American Gold Rush prefabrication in the nineteenth century, the Sears precut homes or Voisin´s prototypes for modular homes, to the end of the first half of the twentieth century. In this period a non negligible number of attempts in 3D modular construction have been carried out, ranging from theoretical proposals to several hundred or thousand units produced. Selected examples of modular architecture will be analyses in order to illustrate its technical evolution, concerning materials, structure, transportation and on site assembly. Success and failure factors of the different systems will be discussed. Conclusions about building criteria shown in them and their applicability in current architecture will be drawn.

High power beam dump project for the accelerator prototype LIPAc: Cooling design and analysis

En el campo de la fusión nuclear y desarrollándose en paralelo a ITER (International Thermonuclear Experimental Reactor), el proyecto IFMIF (International Fusion Material Irradiation Facility) se enmarca dentro de las actividades complementarias encaminadas a solucionar las barreras tecnológicas que aún plantea la fusión. En concreto IFMIF es una instalación de irradiación cuya misión es caracterizar materiales resistentes a condiciones extremas como las esperadas en los futuros reactores de fusión como DEMO (DEMOnstration power plant). Consiste de dos aceleradores de deuterones que proporcionan un haz de 125 mA y 40 MeV cada uno, que al colisionar con un blanco de litio producen un flujo neutrónico intenso (1017 neutrones/s) con un espectro similar al de los neutrones de fusión [1], [2]. Dicho flujo neutrónico es empleado para irradiar los diferentes materiales candidatos a ser empleados en reactores de fusión, y las muestras son posteriormente examinadas en la llamada instalación de post-irradiación. Como primer paso en tan ambicioso proyecto, una fase de validación y diseño llamada IFMIFEVEDA (Engineering Validation and Engineering Design Activities) se encuentra actualmente en desarrollo. Una de las actividades contempladas en esta fase es la construcción y operación de una acelarador prototipo llamado LIPAc (Linear IFMIF Prototype Accelerator). Se trata de un acelerador de deuterones de alta intensidad idéntico a la parte de baja energía de los aceleradores de IFMIF. Los componentes del LIPAc, que será instalado en Japón, son suministrados por diferentes países europeos. El acelerador proporcionará un haz continuo de deuterones de 9 MeV con una potencia de 1.125 MW que tras ser caracterizado con diversos instrumentos deberá pararse de forma segura. Para ello se requiere un sistema denominado bloque de parada (Beam Dump en inglés) que absorba la energía del haz y la transfiera a un sumidero de calor. España tiene el compromiso de suministrar este componente y CIEMAT (Centro de Investigaciones Energéticas Medioambientales y Tecnológicas) es responsable de dicha tarea. La pieza central del bloque de parada, donde se para el haz de iones, es un cono de cobre con un ángulo de 3.5o, 2.5 m de longitud y 5 mm de espesor. Dicha pieza está refrigerada por agua que fluye en su superficie externa por el canal que se forma entre el cono de cobre y otra pieza concéntrica con éste. Este es el marco en que se desarrolla la presente tesis, cuyo objeto es el diseño del sistema de refrigeración del bloque de parada del LIPAc. El diseño se ha realizado utilizando un modelo simplificado unidimensional. Se han obtenido los parámetros del agua (presión, caudal, pérdida de carga) y la geometría requerida en el canal de refrigeración (anchura, rugosidad) para garantizar la correcta refrigeración del bloque de parada. Se ha comprobado que el diseño permite variaciones del haz respecto a la situación nominal siendo el flujo crítico calorífico al menos 2 veces superior al nominal. Se han realizado asimismo simulaciones fluidodinámicas 3D con ANSYS-CFX en aquellas zonas del canal de refrigeración que lo requieren. El bloque de parada se activará como consecuencia de la interacción del haz de partículas lo que impide cualquier cambio o reparación una vez comenzada la operación del acelerador. Por ello el diseño ha de ser muy robusto y todas las hipótesis utilizadas en la realización de éste deben ser cuidadosamente comprobadas. Gran parte del esfuerzo de la tesis se centra en la estimación del coeficiente de transferencia de calor que es determinante en los resultados obtenidos, y que se emplea además como condición de contorno en los cálculos mecánicos. Para ello por un lado se han buscado correlaciones cuyo rango de aplicabilidad sea adecuado para las condiciones del bloque de parada (canal anular, diferencias de temperatura agua-pared de decenas de grados). En un segundo paso se han comparado los coeficientes de película obtenidos a partir de la correlación seleccionada (Petukhov-Gnielinski) con los que se deducen de simulaciones fluidodinámicas, obteniendo resultados satisfactorios. Por último se ha realizado una validación experimental utilizando un prototipo y un circuito hidráulico que proporciona un flujo de agua con los parámetros requeridos en el bloque de parada. Tras varios intentos y mejoras en el experimento se han obtenido los coeficientes de película para distintos caudales y potencias de calentamiento. Teniendo en cuenta la incertidumbre de las medidas, los valores experimentales concuerdan razonablemente bien (en el rango de 15%) con los deducidos de las correlaciones. Por motivos radiológicos es necesario controlar la calidad del agua de refrigeración y minimizar la corrosión del cobre. Tras un estudio bibliográfico se identificaron los parámetros del agua más adecuados (conductividad, pH y concentración de oxígeno disuelto). Como parte de la tesis se ha realizado asimismo un estudio de la corrosión del circuito de refrigeración del bloque de parada con el doble fin de determinar si puede poner en riesgo la integridad del componente, y de obtener una estimación de la velocidad de corrosión para dimensionar el sistema de purificación del agua. Se ha utilizado el código TRACT (TRansport and ACTivation code) adaptándalo al caso del bloque de parada, para lo cual se trabajó con el responsable (Panos Karditsas) del código en Culham (UKAEA). Los resultados confirman que la corrosión del cobre en las condiciones seleccionadas no supone un problema. La Tesis se encuentra estructurada de la siguiente manera: En el primer capítulo se realiza una introducción de los proyectos IFMIF y LIPAc dentro de los cuales se enmarca esta Tesis. Además se describe el bloque de parada, siendo el diseño del sistema de rerigeración de éste el principal objetivo de la Tesis. En el segundo y tercer capítulo se realiza un resumen de la base teórica así como de las diferentes herramientas empleadas en el diseño del sistema de refrigeración. El capítulo cuarto presenta los resultados del relativos al sistema de refrigeración. Tanto los obtenidos del estudio unidimensional, como los obtenidos de las simulaciones fluidodinámicas 3D mediante el empleo del código ANSYS-CFX. En el quinto capítulo se presentan los resultados referentes al análisis de corrosión del circuito de refrigeración del bloque de parada. El capítulo seis se centra en la descripción del montaje experimental para la obtención de los valores de pérdida de carga y coeficiente de transferencia del calor. Asimismo se presentan los resultados obtenidos en dichos experimentos. Finalmente encontramos un capítulo de apéndices en el que se describen una serie de experimentos llevados a cabo como pasos intermedios en la obtención del resultado experimental del coeficiente de película. También se presenta el código informático empleado para el análisis unidimensional del sistema de refrigeración del bloque de parada llamado CHICA (Cooling and Heating Interaction and Corrosion Analysis). ABSTRACT In the nuclear fusion field running in parallel to ITER (International Thermonuclear Experimental Reactor) as one of the complementary activities headed towards solving the technological barriers, IFMIF (International Fusion Material Irradiation Facility) project aims to provide an irradiation facility to qualify advanced materials resistant to extreme conditions like the ones expected in future fusion reactors like DEMO (DEMOnstration Power Plant). IFMIF consists of two constant wave deuteron accelerators delivering a 125 mA and 40 MeV beam each that will collide on a lithium target producing an intense neutron fluence (1017 neutrons/s) with a similar spectra to that of fusion neutrons [1], [2]. This neutron flux is employed to irradiate the different material candidates to be employed in the future fusion reactors, and the samples examined after irradiation at the so called post-irradiative facilities. As a first step in such an ambitious project, an engineering validation and engineering design activity phase called IFMIF-EVEDA (Engineering Validation and Engineering Design Activities) is presently going on. One of the activities consists on the construction and operation of an accelerator prototype named LIPAc (Linear IFMIF Prototype Accelerator). It is a high intensity deuteron accelerator identical to the low energy part of the IFMIF accelerators. The LIPAc components, which will be installed in Japan, are delivered by different european countries. The accelerator supplies a 9 MeV constant wave beam of deuterons with a power of 1.125 MW, which after being characterized by different instruments has to be stopped safely. For such task a beam dump to absorb the beam energy and take it to a heat sink is needed. Spain has the compromise of delivering such device and CIEMAT (Centro de Investigaciones Energéticas Medioambientales y Tecnológicas) is responsible for such task. The central piece of the beam dump, where the ion beam is stopped, is a copper cone with an angle of 3.5o, 2.5 m long and 5 mm width. This part is cooled by water flowing on its external surface through the channel formed between the copper cone and a concentric piece with the latter. The thesis is developed in this realm, and its objective is designing the LIPAc beam dump cooling system. The design has been performed employing a simplified one dimensional model. The water parameters (pressure, flow, pressure loss) and the required annular channel geometry (width, rugoisty) have been obtained guaranteeing the correct cooling of the beam dump. It has been checked that the cooling design allows variations of the the beam with respect to the nominal position, being the CHF (Critical Heat Flux) at least twice times higher than the nominal deposited heat flux. 3D fluid dynamic simulations employing ANSYS-CFX code in the beam dump cooling channel sections which require a more thorough study have also been performed. The beam dump will activateasaconsequenceofthe deuteron beam interaction, making impossible any change or maintenance task once the accelerator operation has started. Hence the design has to be very robust and all the hypotheses employed in the design mustbecarefully checked. Most of the work in the thesis is concentrated in estimating the heat transfer coefficient which is decisive in the obtained results, and is also employed as boundary condition in the mechanical analysis. For such task, correlations which applicability range is the adequate for the beam dump conditions (annular channel, water-surface temperature differences of tens of degrees) have been compiled. In a second step the heat transfer coefficients obtained from the selected correlation (Petukhov- Gnielinski) have been compared with the ones deduced from the 3D fluid dynamic simulations, obtaining satisfactory results. Finally an experimental validation has been performed employing a prototype and a hydraulic circuit that supplies a flow with the requested parameters in the beam dump. After several tries and improvements in the experiment, the heat transfer coefficients for different flows and heating powers have been obtained. Considering the uncertainty in the measurements the experimental values agree reasonably well (in the order of 15%) with the ones obtained from the correlations. Due to radiological reasons the quality of the cooling water must be controlled, hence minimizing the copper corrosion. After performing a bibligraphic study the most adequate water parameters were identified (conductivity, pH and dissolved oxygen concentration). As part of this thesis a corrosion study of the beam dump cooling circuit has been performed with the double aim of determining if corrosion can pose a risk for the copper beam dump , and obtaining an estimation of the corrosion velocitytodimension the water purification system. TRACT code(TRansport and ACTivation) has been employed for such study adapting the code for the beam dump case. For such study a collaboration with the code responsible (Panos Karditsas) at Culham (UKAEA) was established. The work developed in this thesis has supposed the publication of three articles in JCR journals (”Journal of Nuclear Materials” y ”Fusion Engineering and Design”), as well as presentations in more than four conferences and relevant meetings.

Evolution and implementation of CDIO initiatives at ETSII-UPM

The School of Industrial Engineering at Universidad Politécnica de Madrid (ETSII-UPM) has been promoting student-centred teaching-learning activities, according to the aims of the Bologna Declaration, well before the official establishment of the European Area of Higher Education. Such student-centred teaching-learning experiences led us to the conviction that project based learning is rewarding, both for students and academics, and should be additionally promoted in our new engineering programmes, adapted to the Grade-Master structure. The level of commitment of our teachers with these activities is noteworthy, as the teaching innovation experiences carried out in the last ten years have led to the foundation of 17 Teaching Innovation Groups at ETSII-UPM, hence leading the ranking of teaching innovation among all UPM centres. Among interesting CDIO activities our students have taken part in especially complex projects, including the Formula Student, linked to the complete development of a competition car, and the Cybertech competition, aimed at the design, construction and operation of robots for different purposes. Additional project-based learning teamwork activities have been linked to toy design, to the development of medical devices, to the implementation of virtual laboratories, to the design of complete industrial installations and factories, among other activities detailed in present study. The implementation of Bologna process will culminate at ETSII-UPM with the beginning of the Master’s Degree in Industrial Engineering, in academic year 2014-15. The program has been successfully approved by the Spanish Agency for Accreditation (ANECA), with the inclusion of a set of subjects based upon the CDIO methodology denominated generally “INGENIA”, linked to the Spanish “ingeniar” (to provide ingenious solutions), also related etymologically in Spanish with “ingeniero”, engineer. INGENIA students will live through the complete development process of a complex product or system and there will be different kind of projects covering most of the engineering majors at ETSII-UPM.

Simplified serviceability design of jointless structures. Experimental verification and application to typical bridge and building structures

In this article an experimental campaign aimed at validating a previously published simplified serviceability design method of the columns of long jointless structures is presented. The proposed method is also extended to include tension stiffening effects which proved to be significant in structures with small amount of reinforcement subjected to small axial loading. This extension allows significant improvement of predictions for this type of element. The campaign involved columns with different reinforcement and squashing load ratios, given that these parameters had been identified as crucial when designing columns subjected to imposed displacements. Experimental results are presented and discussed, with particular regard to cracking behaviour and structural stiffness. Considerations on tension stiffening effects are also made. Finally, the application of the method to typical bridge and building cases is presented, showing the feasibility of jointless construction, and the limits which should be respected.

Estudio de las propiedades de las fábricas históricas de adobe como soporte a intervenciones de rehabilitación

El extenso legado edificado que constituyen las construcciones históricas de fábrica de adobe distribuidas por toda la península encuentra en la región de Aveiro (Portugal) su máxima expresión, tanto desde el punto de vista cuantitativo, un 30% de los edificios existentes en la región, como tipológico, compuesto por un amplio conjunto de diferentes construcciones (edificios residenciales, edificios militares, iglesias, escuelas, teatros, naves industriales, etc.), muchos de los cuales de reconocido valor histórico, arquitectónico y patrimonial. Tras la gradual desaparición del empleo de la fábrica de adobe como técnica constructiva, durante la segunda mitad del siglo XX, la necesaria conservación y/o rehabilitación de los edificios remanentes no se ha tenido en cuenta. Como consecuencia de esta actitud generalizada de pasividad continuada, se verifica el estado actual de deterioro y de daño acusado que presentan una gran parte de estas construcciones, del cual ha resultado el panorama presente de abandono y ruina en el que se encuentran muchas de ellas. Por regla general, la solución adoptada para afrontar el estado actual de los edificios en estas condiciones suele ser la demolición. No obstante lo anterior, en los últimos años, se viene produciendo en el seno de los diferentes agentes que intervienen en la toma de decisiones sobre estos edificios un interés creciente en su preservación, promoviendo la rehabilitación de los mismos. Empieza de este modo a cobrar importancia la necesidad de desarrollar estrategias de intervención que posibiliten alargar la vida útil de estas estructuras, permitiendo, por un lado, establecer metodologías de análisis de sus condiciones de seguridad, que posibiliten determinar las medidas de actuación necesarias para el aseguramiento de las mismas frente a las acciones existentes y, en su caso, a la incorporación de nuevas solicitaciones debidas a cambios de uso o ampliaciones, así como, dando respuesta a los principales mecanismo de daño a los que se encuentran sujetas. Tratándose de estructuras que fueron construidas utilizando técnicas y materiales escasamente estudiados y entre tanto abandonados, se hace también necesario, y con carácter previo a lo anterior, acometer un estudio e investigación multidisciplinares que permitan su caracterización y comprensión, y la par establecer un diagnóstico sobre los principales agentes y procesos patológicos que promueven el deterioro de las mismas. En este contexto, el estudio llevado a cabo tuvo como objetivos ampliar el conocimiento e investigación acerca de las propiedades y parámetros resistentes de las fábricas históricas de adobe, así como, analizar los principales mecanismos de daño asociados a las mismas, a la luz del el estado actual de estas construcciones, y su repercusión en el comportamiento resistente de las fábricas –con especial énfasis para la influencia del agua–. De este modo, se pretendió construir una base de resultados que, por un lado, pueda servir de soporte a intervenciones de rehabilitación y/o consolidación de estas estructuras – permitiendo de forma ágil y a partir de datos y recursos de cálculo expeditos la evaluación de los niveles de seguridad en las fábricas–, y por otro, el estudio de soluciones de mejora o corrección de deficiencias en su comportamiento estructural. The vast edified legacy composed of the historical adobe load-bearing walls which can be found spread all over the Iberian peninsula has, in the region of Aveiro (Portugal), its maximum expression, both from a quantitative point of view (around 30% of the local construction) and a typological point of view, including a considerable number of different types of constructions (residential buildings, military buildings, churches, industrial buildings, etc.), most of which have a recognized high historical, architectural and patrimonial value. The conservation and/or rehabilitation of many of these edifications has been neglected, since its gradual abandonment as constructive technique during the second half of the 20th century. As a consequence of this posture of general passivity, it is nowadays visible the state of pronounced damage manifested by great part of these constructions, which has been leading to their abandonment and state of ruin. In most cases, the option for demolition has been the solution found to face the actual state of these constructions. However, in recent years, a growing interest in the preservation and maintenance of the adobe constructions has become visible by the envolved parties, with the obvious consequence of rehabilitation. By so, it becomes mandatory to develop strategies of intervention that, through rehabilitation, are able to extend the useful life of the existing structures, allowing on one hand, to establish methodologies to analyze their safety state and determine the actions needed to ensure their protection against existing pressures and, when applicable, the occurrence of new demands due to changes of use or extensions, and on the other hand, to give response to the main damage mechanisms to which these structures are exposed. Because these structures were built using not very well know techniques and materials, which have been, in the meantime, abandoned, it is now crucial that these are object of a previous phase of study and multidisciplinary investigation, essential not only to their characterization and comprehension, but also to the diagnosis of the main pathological processes that affect them. In this context, the present study had as main goal to develop the analysis and knowledge regarding the properties and resistant parameters of the adobe masonry as well as bringing to the light of day the actual state of the existing adobe constructions, making evident the main damage mechanisms by which they are affected and analyzing, through their occurrence, the vulnerability of the mentioned properties and resistant parameters. By so, it was objective of the present study the development of a result database which on one hand, supports the execution of rehabilitation interventions and/or strengthening of these constructions and, on other hand, allows the development of improvement solutions in the mechanical characteristics of the adobe masonry which permit corrections of deficiencies in their structural behavior with a special emphasis on the influence of water. Thus, a database of results was developed. Its goal is, on one hand, to support the rehabilitation or consolidation interventions on these structures - allowing for a quick analysis of the safety state of the adobe walls from expedite data and calculus resources and, on the other hand, to study improvement or correction solutions of their structural behavior.

Comparative Life Cycle Assessment of the Conventional Façade SOS Natura and the Natural Water Tank Façade

The construction industry produces great environmental impacts to the planet. In order to tackle this problem, the European Union has put into effect Regulation No 305/2011, which compels the construction products manufacturers to carry out environmental performance studies of these products and thus make public the impact they cause on the environment. The aim of this research is to make known the environmental impacts of the SOS Natura Conventional Façade (CF) solution, obtained within the research project "SOS Natura, Vegetal Architectural Solutions" developed by the Department of Construction and Technology in Architecture of the School of Architecture of the Technical University of Madrid (Spain). In addition, we report an environmental comparative with the Natural Water Tank Façade (NWTF), studied previously by the same work group and included in the same research project.We present as well an uncertainty analysis for both façades. Following the study conducted we conclude that the NWTF profile has a slightly better environmental behaviour when compared to the CF profile for the entire life cycle in most of the impact categories analysed in this study. However it should also be noted that, in detail and at stage level, the NWTF presents a higher environmental impact than the CF.