An Analytical Solution for the Elastic Lateral-Distortional Buckling of I-section Beams

Lateral-distortional buckling may occur in I-section beams with slender webs and stocky flanges. A computationally efficient method is presented in this paper to study this phenomenon. Previous studies on distortional buckling have been on the use of 3(rd) and 5(th) order polynomials to model the displacements. The present study provides an alternative way, using Fourier Series, to model the behaviour. Beams of different cross-sectional dimensions, load cases and restraint conditions are examined and compared. The accuracy and versatility of the method are verified by calibrating against the results of other published studies. The present method is believed to be a simple and efficient way of determining the buckling load and mode shapes of I-section beams that are susceptible to lateral-distortional buckling modes.

Mechanical effects of plant cell wall enzymes on cellulose/xyloglucan composites

Xyloglucan-acting enzymes are believed to have effects on type I primary plant cell wall mechanical properties. In order to get a better understanding of these effects, a range of enzymes with different in vitro modes of action were tested against cell wall analogues (bio-composite materials based on Acetobacter xylinus cellulose and xyloglucan). Tomato pericarp xyloglucan endo transglycosylase (tXET) and nasturtium seed xyloglucanase (nXGase) were produced heterologously in Pichia pastoris. Their action against the cell wall analogues was compared with that of a commercial preparation of Trichoderma endo-glucanase (EndoGase). Both 'hydrolytic' enzymes (nXGase and EndoGase) were able to depolymerise not only the cross-link xyloglucan fraction but also the surface-bound fraction. Consequent major changes in cellulose fibril architecture were observed. In mechanical terms, removal of xyloglucan cross-links from composites resulted in increased stiffness (at high strain) and decreased visco-elasticity with similar extensibility. On the other hand, true transglycosylase activity (tXET) did not affect the cellulose/xyloglucan ratio. No change in composite stiffness or extensibility resulted, but a significant increase in creep behaviour was observed in the presence of active tXET. These results provide direct in vitro evidence for the involvement of cell wall xyloglucan-specific enzymes in mechanical changes underlying plant cell wall re-modelling and growth processes. Mechanical consequences of tXET action are shown to be complimentary to those of cucumber expansin.

Characterization of heat shock protein-specific T cells in atherosclerosis

A role for infection and inflammation in atherogenesis is widely accepted. Arterial endothelium has been shown to express heat shock protein 60 (HSP60) and, since human (hHSP60) and bacterial (GroEL) HSP60s are highly conserved, the immune response to bacteria may result in cross-reactivity, leading to endothelial damage and thus contribute to the pathogenesis of atherosclerosis. In this study, GroEL-specific T-cell lines from peripheral blood and GroEL-, hHSP60-, and Porphyromonas gingivalis-specific T-cell lines from atherosclerotic plaques were established and characterized in terms of their cross-reactive proliferative responses, cytokine and chemokine profiles, and T-cell receptor (TCR) V beta expression by flow cytometry. The cross-reactivity of several lines was demonstrated. The cytokine profiles of the artery T-cell lines specific for GroEL, hHSP60, and P. gingivalis demonstrated Th2 phenotype predominance in the CD4 subset and Tc0 phenotype predominance in the CD8 subset. A higher proportion of CD4 cells were positive for interferon-inducible protein 10 and RANTES, with low percentages of cells positive for monocyte chemoattractant protein 1 and macrophage inflammatory protein la, whereas a high percentage of CD8 cells expressed all four chemokines. Finally, there was overexpression of the TCR V beta 5.2 family in all lines. These cytokine, chemokine, and V beta profiles are similar to those demonstrated previously for P. gingivalis-specific lines established from periodontal disease patients. These results support the hypothesis that in some patients cross-reactivity of the immune response to bacterial HSPs, including those of periodontal pathogens, with arterial endothelial cells expressing hHSP60 may explain the apparent association between atherosclerosis and periodontal infection.

Determinants of stages of smoking uptake among secondary school students

With the uptake of cigarette smoking hypothesised to occur through a series of contemplation and action stages, we sought to investigate what factors are associated with the contemplation of smoking among secondary school students in Queensland, Australia. A series of four cross-sectional surveys were conducted among secondary schools in Queensland in 1993, 1996, 1999 and 2002. Respondents (n = 9993) were asked about the stages of smoking. Nearly half (43%) of secondary school students reported some contemplation of smoking. Increased levels of smoking contemplation were observed among females, earlier survey years, Junior level students, students with average or below average scholastic ability, those prepared to go out with a smoker, those with recent alcohol experience, those who bad influenced other students to smoke or had not discouraged other students smoking. The results of this study provide further information about the factors relevant to stages of smoking uptake among secondary school students and the influence that students may have on their peers. (c) 2005 Elsevier Ltd. All rights reserved.

Transport of simple fluids in nanopores: Theory and simulation

A theory is discussed of single-component transport in nanopores, recently developed by Bhatia and coworkers. The theory considers the oscillatory motion of molecules between diffuse wall collisions, arising from the fluid-wall interaction, along with superimposed viscous flow due to fluid-fluid interaction. The theory is tested against molecular dynamics simulations for hydrogen, methane, and carbon tetrafluoride flow in cylindrical nanopores in silica. Although exact at low densities, the theory performs well even at high densities, with the density dependency of the transport coefficient arising from viscous effects. Such viscous effects are reduced at high densities because of the large increase in viscosity, which explains the maximum in the transport coefficient with increase in density. Further, it is seen that in narrow pore sizes of less than two molecular diameters, where a complete monolayer cannot form on the surface, the mutual interference of molecules on opposite sides of the cross section can reduce the transport coefficient, and lead to a maximum in the transport coefficient with increasing density. The theory is also tested for the case of partially diffuse reflection and shows the viscous contribution to be negligible when the reflection is nearly specular. (c) 2005 American Institute of Chemical Engineers AIChE J, 52: 29-38, 2006.

The cross-entropy method for continuous multi-extremal optimization

In recent years, the cross-entropy method has been successfully applied to a wide range of discrete optimization tasks. In this paper we consider the cross-entropy method in the context of continuous optimization. We demonstrate the effectiveness of the cross-entropy method for solving difficult continuous multi-extremal optimization problems, including those with non-linear constraints.

Effect of sample geometry on regression rate of the melting interface for carbon steel burned in oxygen

Promoted-ignition testing on carbon steel rods of varying cross-sectional area and shape was performed in high pressure oxygen to assess the effect of sample geometry on the regression rate of the melting interface. Cylindrical and rectangular geometries and three different cross sections were tested and the regression rates of the cylinders were compared to the regression rates of the rectangular samples at test pressures around 6.9 MPa. Tests were recorded and video analysis used to determine the regression rate of the melting interface by a new method based on a drop cycle which was found to provide a good basis for statistical analysis and provide excellent agreement to the standard averaging methods used. Both geometries tested showed the typical trend of decreasing regression rate of the melting interface with increasing cross-sectional area; however, it was shown that the effect of geometry is more significant as the sample's cross sections become larger. Discussion is provided regarding the use of 3.2-mm square rods rather than 3.2-mm cylindrical rods within the standard ASTM test and any effect this may have on the observed regression rate of the melting interface.

In vivo demonstration of load-induced fluid flow in the rat tibia and its potential implications for processes associated with functional adaptation

Load-induced extravascular fluid flow has been postulated to play a role in mechanotransduction of physiological loads at the cellular level. Furthermore, the displaced fluid serves as a carrier for metabolites, nutrients, mineral precursors and osteotropic agents important for cellular activity. We hypothesise that load-induced fluid flow enhances the transport of these key substances, thus helping to regulate cellular activity associated with processes of functional adaptation and remodelling. To test this hypothesis, molecular tracer methods developed previously by our group were applied in vivo to observe and quantify the effects of load-induced fluid flow under four-point-bending loads. Preterminal tracer transport studies were carried out on 24 skeletally mature Sprague Dawley rats. Mechanical loading enhanced the transport of both small- and larger-molecular-mass tracers within the bony tissue of the tibial mid-diaphysis. Mechanical loading showed a highly significant effect on the number of periosteocytic spaces exhibiting tracer within the cross section of each bone. For all loading rates studied, the concentration of Procion Red tracer was consistently higher in the tibia subjected to pure bending loads than in the unloaded, contralateral tibia, Furthermore, the enhancement of transport was highly site-specific. In bones subjected to pure bending loads, a greater number of periosteocytic spaces exhibited the presence of tracer in the tension band of the cross section than in the compression band; this may reflect the higher strains induced in the tension band compared with the compression band within the mid-diaphysis of the rat tibia. Regardless of loading mode, the mean difference between the loaded side and the unloaded contralateral control side decreased with increasing loading frequency. Whether this reflects the length of exposure to the tracer or specific frequency effects cannot be determined by this set of experiments. These in vivo experimental results corroborate those of previous ex vivo and in vitro studies, Strain-related differences in tracer distribution provide support for the hypothesis that load-induced fluid flow plays a regulatory role in processes associated with functional adaptation.

An antigen capture enzyme-linked immunosorbent assay reveals high levels of the dengue virus protein NS1 in the sera of infected patients

We describe the development of a capture enzyme-linked immunosorbent assay for the detection of the dengue virus nonstructural protein NS1. The assay employs rabbit polyclonal and monoclonal antibodies as the capture and detection antibodies, respectively. Immunoaffinity-purified NS1 derived from dengue 2 virus-infected cells was used as a standard to establish a detection sensitivity of approximately 4 ng/ml for an assay employing monoclonal antibodies recognizing a dengue 2 serotype-specific epitope. A number of serotype cross-reactive monoclonal antibodies were also shown to be suitable probes for the detection of NS1 expressed by the remaining three dengue virus serotypes. Examination of clinical samples demonstrated that the assay was able to detect NS1 with minimal interference from serum components at the test dilutions routinely used, suggesting that it could form the basis of a useful additional diagnostic test for dengue virus infection. Furthermore, quantitation of NS1 levels in patient sera may prove to be a valuable surrogate marker for viremia. Surprisingly high levels of NS1, as much as 15 mu g/ml, were found in acute-phase sera taken hom some of the patients experiencing serologically confirmed dengue 2 virus secondary infections but was not detected in the convalescent sera of these patients. In contrast, NS1 could not be detected in either acute-phase or convalescent serum samples taken from patients with serologically confirmed primary infection. The presence of high levels of secreted NS1 in the sera of patients experiencing secondary dengue virus infections, and in the context of an anamnestic antibody response, suggests that NS1 may contribute significantly to the formation of the circulating immune complexes that are suspected to play an important role in the pathogenesis of severe dengue disease.

DEVELOPMENT OF INTEGRATED BIOPROCESSING TECHNOLOGIES FOR THE PRODUCTION OF PECTIC OLIGOSACCHARIDES (POS) FROM AGRO-PROCESSING RESIDUES

This research deals with the production of pectic oligosaccharides (POS) from agro-industrial residues, with specific focus on development of continuous cross flow enzyme membrane reactor. Pectic oligosaccharides have recently gained attention due to their prebiotic activity. Lack of information on the continuous production of POS from agro-industrial residues formed the basis for the present study. Four residues i.e sugar beet pulp, onion hulls, pressed pumpkin cake and berry pomace were taken to study their pectin content. Based on the presence of higher galacturonic acid and arabinose (both homogalacturonan and rhamnogalacturonan) in sugar beet pulp and galacturonic acid (only homogalacturonan) in onion hulls, further optimization of different extraction methods of pectin (causing minimum damage to pectic chain) from these residues were done. The most suitable extractant for sugar beet pulp and onion hulls were nitric acid and sodium hexametaphosphate respectively. Further the experiments on the continuous production of POS from sugar beet pulp in an enzyme membrane reactor was initiated. Several optimization experiments indicated the optimum enzyme (Viscozyme) as well as feed concentration (25 g/L) to be used for producing POS from sugar beet pulp in an enzyme membrane reactor. The results highlighted that steady state POS production with volumetric and specific productivity of 22g/L/h and 11 g/gE/h respectively could be achieved by continuous cross flow filtration of sugar beet pulp pectic extract over 10 kDa membrane at residence time of 20 min. The POS yield of about 80% could be achieved using above conditions. Also, in this thesis preliminary experiments on the production and characterization of POS from onion hulls were conducted. The results revelaed that the most suitable enzyme for POS production from onion hulls is endo-polygalacturonase M2. The POS produced from onion hulls were present in the form of DP1 -DP10 in substituted as well as unsubstituted forms. This study clearly demonstrates that continuous production of POS from pectin rich sources can be achieved by using cross flow continuous enzyme membrane reactor.

Reformulation of a thermostable broadly protective recombinant vaccine against human papilloma virus

The causal relationship between Human Papilloma Virus (HPV) infection and cervical cancer has motivated the development, and further improvement, of prophylactic vaccines against this virus. 70% of cervical cancers, 80% of which in low-resources countries, are associated to HPV16 and HPV18 infection, with 13 additional HPV types, classified as high-risk, responsible for the remaining 30% of tumors. Current vaccines, Cervarix® (GlaxoSmithKline) and Gardasil®(Merk), are based on virus-like particles (VLP) obtained by self-assembly of the major capsid protein L1. Despite their undisputable immunogenicity and safety, the fact that protection afforded by these vaccines is largely limited to the cognate serotypes included in the vaccine (HPV 16 and 18, plus five additional viral types incorporated into a newly licensed nonavalent vaccine) along with high production costs and reduced thermal stability, are pushing the development of 2nd generation HPV vaccines based on minor capsid protein L2. The increase in protection broadness afforded by the use of L2 cross-neutralizing epitopes, plus a marked reduction of production costs due to bacterial expression of the antigens and a considerable increase in thermal stability could strongly enhance vaccine distribution and usage in low-resource countries. Previous studies from our group identified three tandem repeats of the L2 aa. 20-38 peptide as a strongly immunogenic epitope if exposed on the scaffold protein thioredoxin (Trx). The aim of this thesis work is the improvement of the Trx-L2 vaccine formulation with regard to cross-protection and thermostability, in order to identify an antigen suitable for a phase I clinical trial. By testing Trx from different microorganisms, we selected P. furiosus thioredoxin (PfTrx) as the optimal scaffold because of its sustained peptide epitope constraining capacity and striking thermal stability (24 hours at 100°C). Alternative production systems, such as secretory Trx-L2 expression in the yeast P. pastoris, have also been set-up and evaluated as possible means to further increase production yields, with a concomitant reduction of production costs. Limitations in immune-responsiveness caused by MHC class II polymorphisms –as observed, for example, in different mouse strains- have been overcome by introducing promiscuous T-helper (Th) epitopes, e.g., PADRE (Pan DR Epitope), at both ends of PfTrx. This allowed us to obtain fairly strong immune responses even in mice (C57BL/6) normally unresponsive to the basic Trx-L2 vaccine. Cross-protection was not increased, however. I thus designed, produced and tested a novel multi-epitope formulation consisting of 8 and 11 L2(20-38) epitopes derived from different HPV types, tandemly joined into a single thioredoxin molecule (“concatemers”). To try to further increase immunogenicity, I also fused our 8X and 11X PfTrx-L2 concatemers to the N-terminus of an engineered complement-binding protein (C4bp), capable to spontaneously assemble into ordered hepatmeric structures, previously validated as a molecular adjuvant. Fusion to C4bp indeed improved antigen presentation, with a fairly significant increase in both immunogenicity and cross-protection. Another important issue I addressed, is the reduction of vaccine doses/treatment, which can be achieved by increasing immunogenicity, while also allowing for a delayed release of the antigen. I obtained preliminary, yet quite encouraging results in this direction with the use of a novel, solid-phase vaccine formulation, consisting of the basic PfTrx-L2 vaccine and its C4bp fusion derivative adsorbed to mesoporus silica-rods (MSR).

Simplified recording of soft contact lens fit

Purpose: To determine the critical fitting characteristics of modern soft contact lens fits and from this to devise a simplified recording scheme. Methods: Ten subjects (aged 28.1 ± 7.4 years) wore eight different modern soft contact lenses. Video was captured and analysed of blink (central and up-gaze), excursion lag (up, down, right and left gaze) and push-up movement, centration and coverage. Results: Lens centration was on average close to the corneal centre. Movement on blink was significantly smaller in up-gaze than in primary-gaze (p<0.001). Lag was greatest in down-gaze and least in up-gaze (p<0.001). Push-up test recovery speed was 1.32±0.73mm/s. Overall lens movement was determined best by assessing horizontal lag, movement on blink in up-gaze and push-up recovery speed. Steeper lens base-curves did not have a significant effect on lens fit characteristics. Contact lens material did influence lens fit characteristics, particularly silicone-hydrogels which generally had lower centration and a faster push-up speed of recovery than HEMA lenses (p<0.05). Conclusion: Lag on vertical gaze, and movement on blink in primary gaze generally provide little extra information on overall lens movement compared to horizontal lag, movement on blink in up gaze and push-up recovery speed. They can therefore be excluded from a simplified recording scheme. A simplified and comprehensive soft contact lens fit recording system could consist of a cross-hairs indicating the centre of the cornea; a circle to indicate the lens centration; a mark on the relevant position of the circle to indicate any limbal incursion; a grade (‘B’) below for movement with blink in up-gaze, a grade (‘L’) to the side for horizontal lag and a grade above (‘P’) for the assessed push-up recovery speed.

Risk based decision support system for effective implementation of projects

Conventional project management techniques are not always sufficient to ensure time, cost and quality achievement of large-scale construction projects due to complexity in planning, design and implementation processes. The main reasons for project non-achievement are changes in scope and design, changes in government policies and regulations, unforeseen inflation, underestimation and improper estimation. Projects that are exposed to such an uncertain environment can be effectively managed with the application of risk management throughout the project's life cycle. However, the effectiveness of risk management depends on the technique through which the effects of risk factors are analysed/quantified. This study proposes the Analytic Hierarchy Process (AHP), a multiple attribute decision making technique, as a tool for risk analysis because it can handle subjective as well as objective factors in a decision model that are conflicting in nature. This provides a decision support system (DSS) to project management for making the right decision at the right time for ensuring project success in line with organisation policy, project objectives and a competitive business environment. The whole methodology is explained through a case application of a cross-country petroleum pipeline project in India and its effectiveness in project management is demonstrated.

Cross-sectional studies in prescribing research

A cross-sectional study aims to describe the overall picture of a phenomenon, a situational problem, an attitude or an issue, by asking a cross-section of a given population at one specified moment in time. This paper describes the key features of the cross-sectional survey method. It begins by highlighting the main principles of the method, then discusses stages in the research process, drawing on two surveys of primary care pharmacists to illustrate some salient points about planning, sampling frames, definition and conceptual issues, research instrument design and response rates. Four constraints in prescribing studies were noted. First the newness of the subject meant a low basis of existing knowledge to design a questionnaire. Second, there was no public existing database for the sampling frame, so a pragmatic sampling exercise was used. Third, the definition of a Primary Care Pharmacist (PCP) [in full] and respondents recognition of that name and identification with the new role limited the response. Fourth, a growing problem for all surveys, but particularly with pharmacists and general practitioners (GP) [in full] is the growing danger of survey fatigue, which has a negative impact on response levels.

Organizing innovation: complementarities between cross-functional teams

Cross-functional teams play a potentially important part in the innovation process enabling knowledge sharing, the development of trust and overcoming spatial and organizational barriers. Using a supermodularity approach, we focus on potential complementarities which may arise when cross-functional teams are used in different elements of the innovation process in UK and German manufacturing plants. Using optimal combinations of cross-functional teams in the innovation process increases innovation success in the UK by 29.5 per cent compared to 9.5 per cent in Germany. Patterns of complementarity are complex, however, but are more uniform in the UK than in Germany. The most uniform complementarities are between product design and development and production engineering, with little synergy evident between the more technical phases of the innovation process and the development of marketing strategy. In strategic terms, our results suggest the value of using cross-functional teams for the more technical elements of the innovation process but that the development of marketing strategy should remain the domain of specialists.