Herstellung hydrophiler Polyurethanpartikel und anisotroper Polymerpartikel

Hydrophile Polyurethanpartikel wurden mittels in inversen Miniemulsionen durchgeführten Polyadditionsreaktionen hergestellt. Wie durch FT-IR-Spektroskopie gezeigt wurde, konnte durch die Abwesenheit von Wasser in dem verwendeten System die Entstehung von Harnstoffbindungen vermieden werden. Das Molekulargewicht der erhaltenen Polyurethane konnte durch verschiedene Parameter, wie zum Beispiel die Hydrophobizität der kontinuierlichen Phase oder die Zugabe von DMSO zur dispersen Phase, beeinflusst werden. Die höchsten Molekulargewichte (Mn von bis zu 19000 g•mol-1) wurden mit Isopar M als kontinuierlicher Phase erhalten. Der zweite Teil der Arbeit beschäftigt sich mit der Herstellung anisotroper Polystyrolpartikel über eine Film-Dehnungs-Methode. Polystyrol/Polyvinylalkohol-Filme wurden oberhalb der Glasübergangstemperatur von Polystyrol und Polyvinylalkohol (Matrix) uniaxial oder biaxial gedehnt, wodurch ellipsenförmige oder scheibenförmige Partikel entstanden. Es zeigte sich, dass die Redispergierbarkeit der verstreckten Partikel in Wasser stark von deren Oberflächenfunktionalisierung abhängig war. Die beste Redispergierbarkeit (46%) wurde für Sulfonat-funktionalisierte Partikel erhalten. Als eine alternative Methode zur Herstellung anisotroper Polymerpartikel wurde im letzten Teil der vorliegenden Arbeit Elektrospinnen eingesetzt. Es konnte gezeigt werden, dass es prinzipiell möglich ist, ellipsenförmige PS-Partikel zu erhalten, deren Aspektverhältnis durch die Höhe der angelegten Spannung und den Abstand zwischen Spitze und Kollektor beeinflusst wurde. Neben PS-Partikeln konnten auch PMMA-Kapseln über Elektrospinnen verstreckt werden. Mittels der Film-Dehnungs-Methode konnte jedoch eine größere Vielfalt an Aspektverhältnissen hergestellt werden. Ein weiterer Nachteil gegenüber der Film-Dehnungs-Methode ist die relativ breite Größenverteilung der verstreckten Partikel. Jedoch ist Elektrospinnen im Gegensatz zur Film-Dehnungs-Methode ein kontinuierlicher Prozess und könnte auch für die Herstellung anisotroper Partikel von Polymeren mit einer hohen Glasübergangstemperatur verwendet werden.

Morphology control in metallocene-catalyzed polyolefin synthesis

The main aim of the work presented in this dissertation was the morphology control in metallocene-catalyzed polyolefin synthesis. This was studied by selective immobilization techniques on a variety of supports such as porous polyurethane particles (Chapter 3), electrospun fibers (Chapter 4 and 5), inorganic-organic hybrid core-shell particles (Chapter 6) and hollow silica particles (Chapter 7). Another aspect of this dissertation was modulating a catalytic activity by controlling a size of boron-based cocatalysts (Chapter 8).

Induktion tolerogener dendritischer Zellen zur Suppression von experimenteller autoimmuner Enzephalomyelitis und Kontaktallergie

Dendritische Zellen (DC) spielen als professionelle antigenpräsentierende Zellen (APC) eine zentrale Rolle in der Aktivierung und Regulierung antigenspezifischer Immunantworten. Aus diesem Grund wird der therapeutische Einsatz von DC zur Behandlung von Autoimmunerkrankungen und Allergien sowie zur Tumorbekämpfung erforscht. Im ersten Teil der vorliegenden Arbeit untersuchten wir das Potenzial einer biolistischen DNA-Vakzinierung zur Induktion tolerogener DC in vivo. Im Tiermodell der Myelin-Oligodendrozyten-Glykoprotein Peptid 35-55 (MOGp35-55) induzierten experimentellen autoimmunen Enzephalomyelitis (EAE) sollte mittels präventiver biolistischer Kovakzinierung von Plasmid-DNA kodierend für MOG und die immunregulatorischen Zytokine TGFβ oder IL-10 eine protektive Immunität induziert werden. Die MOG-Expression stand dabei entweder unter der Kontrolle des ubiquitär aktiven CMV-Promotors oder des murinen Fascin-Promotors, um eine ektopische MOG-Expression spezifisch in dermalen DC und Langerhanszellen zu erreichen. Dass MOGp35-55-präsentierende DC nach biolistischer DNA-Vakzinierung von der Haut in die drainierenden Lymphknoten migrieren und dort T-Zellen aktivieren, konnte im Vorfeld anhand einer substanziellen Proliferation von MOGp35-55-reaktiven 2D2 T-Zellen nachgewiesen werden. Im präventiven Ansatz der MOGp35-55-induzierten EAE zeigten Mäuse, die mit MOG-kodierenden Plasmiden biolistisch transfiziert wurden, eine leicht reduzierte EAE-Symptomatik. Die Kotransfektion von MOG und TGFβ führte zu einer Verstärkung der EAE-Suppression – unabhängig davon, ob die MOG-Expression unter der Kontrolle des CMV- oder des Fascin-Promotors stand. Interessanterweise resultierte die Koapplikation von MOG- und IL-10-kodierender Plasmid-DNA nur bei DC-fokussierter MOG-Expression zu reduzierter EAE-Symptomatik. Für biolistische DNA-Vakzinierungen stellt somit der Fascin-Promotor eine potente Alternative zu viralen Promotoren dar. Entsprechend der milderen EAE-Symptome beobachteten wir bei behandelten EAE-Mäusen einen geringeren Grad an Demyelinisierung sowie eine reduzierte Infiltration des ZNS mit IFNγ-produzierenden CD4+ Th1- und IL-17-produzierenden CD4+ Th17-Zellen. Desweiteren zeigten Milzzellen ex vivo nach MOGp35-55-Restimulation eine inhibierte Proliferation und eine signifikant reduzierte IFNγ- und IL-17-Zytokinproduktion. Überraschenderweise ging die antigenspezifische Immunsuppression nicht mit der Expansion von Foxp3+ regulatorischen T-Zellen einher. Da die Milzen aber erhöhte Mengen an CD8+IFNγ+ T-Zellen aufweisen, könnte ein zytotoxisch-suppressiver Mechanismus für die Inhibition der Th1- und Th17-Immunantwort verantwortlich sein. Nachfolgende Untersuchungen sind notwendig, um die induzierten immunologischen Mechansimen mittels biolistischer DNA-Vakzinierung aufzuklären. Der zweite Teil der Arbeit befasst sich mit der Generierung von tolerogenen DC in vitro. Dafür wurden murine Knochenmarkszellen unter DC-differenzierenden Bedingungen in Gegenwart des synthetischen Glucocorticoids Dexamethason (DEX) kultiviert. Die DEX-Zugabe führte zur Differenzierung von APC mit geringer CD11c-Expression. DEX-APC waren in vitro weitestgehend gegen LPS stimulierungsresistent und zeigten eine reduzierte Expression von MHC-II und den kostimulatorischen Molekülen CD80, CD86 und CD40. Ihrem tolerogenen Phänotyp entsprechend besaßen DEX-APC ein geringeres syngenes T-Zellstimulierungspotenzial als unbehandelte BM-DC. Anhand der erhöhten Oberflächenexpression von CD11b, GR1 und F4/80 besteht eine phänotypische Ähnlichkeit zu myeloiden Suppressorzellen. Die Fähigkeit von DEX-APC in vivo antigenspezifische Toleranz zu induzieren, wurde durch einen therapeutischen Ansatz im murinen Krankheitsmodell der Kontaktallergie überprüft. Die therapeutische Applikation von DEX-APC führte hierbei im Vergleich zur Applikation von PBS oder unbehandelten BM-DC zu einer signifikant reduzierten Ohrschwellungsreaktion. Zusammenfassend demonstrieren die Ergebnisse dieser Arbeit, dass potente tolerogene DC sowohl in vivo als auch in vitro induziert werden können. Dass diese Zellpopulation effektiv antigenspezifische Immunreaktionen supprimieren kann, macht sie zu einem vielversprechenden Werkzeug in der Behandlung von Autoimmunerkrankungen und Allergien.rn

Non-aqueous dispersions of particles and their applications

In the current work, three studies about non-aqueous dispersions of particles were carried out by using an amphiphilic block copolymer poly(isoprene)-block-poly(methyl methacrylate) (PI-b-PMMA) as stabilizer:rn1. Dispersions of polyurethane and polyurea porous particles for polymer compositesrn2. Dispersions of PMMA and PU particles with PDI dye for study of Single Molecule Spectroscopy Detectionrn3. Dispersions of graphene nanosheets for polymer compositesrnrnIn the first study, highly porous polyurethane and polyurea particles were prepared in a non-aqueous emulsion. The preparation of porous particles consisted of two parts: At first, a system was developed where the emulsion had high stability for the polymerization among diisocyanate, diol and water. In the second part, porous particles were prepared by using two methods fission/fusion and combination by which highly porous particles were obtained. In this study, the applications of porous particles were also investigated where polyurethane particles were tested as filling material for polymer composites and as catalyst carrier for polyethylene polymerization. rnrnIn the second study, PMMA and PU particles from one non-aqueous emulsion were investigated via single molecule fluorescence detection. At first the particles were loaded with PDI dye, which were detected by fluorescence microscopy. The distribution and orientation of the PDI molecules in the particles were successfully observed by Single Molecule Fluorescence Detection. The molecules were homogenously distributed inside of the particles. In addition they had random orientation, meaning that no aggregations of dye molecules were formed. With the results, it could be supposed that the polymer chains were also homogenously distributed in the particles, and that the conformation was relatively flexible. rnrnIn the third part of the study, graphene nanosheets with high surface area were dispersed in an organic solvent with low boiling point and low toxicity, THF, stabilized with a block copolymer PI-b-PMMA. The dispersion was used to prepare polymer composites. It was shown that the modified graphene nanosheets had good compatibility with the PS and PMMA matrices. rn

Strukturbildung in Polyurethandispersionen und -filmen

Mechanische Eigenschaften nach Verfilmen sind häufig die wichtigsten Anforderungen für Polyurethandispersionen, so werden beispielsweise in den Hauptanwendungen im Beschichtungs- und Klebstoffsektor oftmals hohe Festigkeiten benötigt. Diese Anforderungen werden in der Dissertation durch eine gezielte Strukurbildung in den Polymeren adressiert. Mit einer hohen Kontrolle über den Polymeraufbau, durch die Ausbildung von kristallinen Bereichen, sowie mit phasenseparierten Morphologien werden drei Konzepte für die Modifikation der mechanischen Eigenschaften vorgestellt: Eine chemische bzw. kovalente Vernetzung wird mit funktionalisierten Polyurethanen erreicht, die physikalische Vernetzung kann reversibel die mechanische Festigkeit von Filmen erhöhen und Hybride mit kontrollierter Morphologie zeigen eine Kombination von Vorteilen ihrer Einzelbestandteile. Ferner zeichnen sich die synthetisierten Polyurethane gegenüber anderen Polymerklassen durch ihre relativ einfache Synthese und die Möglichkeit zur Herstellung multifunktionaler Materialien aus.

Long-term evaluation of myoblast seeded patches implanted on infarcted rat hearts

Cell transplantation presents great potential for treatment of patients with severe heart failure. However, its clinical application was revealed to be more challenging than initially expected in experimental studies. Further investigations need to be undertaken to define the optimal treatment conditions. We previously reported on the epicardial implantation of a bio-engineered construct of skeletal myoblast-seeded polyurethane and its preventive effect on progression toward heart failure. In the present study, we present a long-term evaluation of this functional outcome. Left anterior descending coronary ligation was performed in female Lewis rats. Two weeks later, animals were treated with either epicardial implantation of biograft, acellular scaffold, sham operation, or direct intramyocardial skeletal myoblast injection. Functional assessments were performed with serial echocardiographies every 3 months and end point left ventricle pressure was assessed. Hearts were then harvested for histological examinations. Myocardial infarction induced a slow and progressive reduction in fractional shortening after 3 months. Progression toward heart failure was significantly prevented for up to 6 months after injection of myoblasts and for up to 9 months following biograft implantation. Nevertheless, this effect vanished after 12 months, with immunohistological examinations revealing an absence of the transplanted myoblasts within the scaffold. We demonstrated that tissue therapy is superior to cell therapy for stabilization of heart function. However, beneficial effects are transient.

An Investigation On The Use Of Microalgae For Biogas Enrichment

There is a need for biomethane capture and carbon dioxide sequestration to mitigate evident global climate change. This research work investigated the potential for microalgae to remove CO2 from biogas as a biotechnical method for upgrading the thermal value for subsequent compression, liquification, or introduction to natural gas pipelines. Because biogas is largely methane, the effect of high methane environments on mixed microalgae was explored and found that specific carbon utilization rates were not statistically different when microalgae were exposed to biogas environments (70% v/v CH4) , relative to high CO2 environment. The uses of conventional bubbled column photobioreactors (PBR) were assessed for CO2 removal and subsequent CH4 enrichment. A continuously-bubbled biogas PBR (cB-PBR5) and intermittently-bubbled biogas PBR (iB-PBR) experienced CO2 loading rates of about 1664 and 832 mg C/L*day and showed 30.0 and 60.1 % carbon removal, respectively. However, a lack of biogas enrichment and issues associated growth inhibition due to high CO2 environments as well as stripping the dissolved gases, namely oxygen and nitrogen, from the bulk liquid and introduction to the outlet gas prompted the consideration for gas/liquid separation using nonporous hollow-fiber (HF) membranes for CO2 transfer. The potential for two non-porous HF membrane materials [polydimethylsiloxane (PDMS) and composite polyurethane (PU)] were modeled along fiber length using a mechanistic model based on polymeric material transport properties (Gilmore et al., 2009). Based on a high CO2:CH4 permeability selectivity for PU of 76.2 the model predicted gas enrichment along an 8.5 cm fiber length. Because PDMS permeability selectivity is low (3.5), evident gas transfer was not predicated along a 34.3 cm length. Both of these HF materials were implemented in hollow-fiber membrane-carbonated biofilm (HFMcB) PBRs for microalgal-mediated biogas enrichment. Phototrophic biofilm colonization occurred on the membrane, where CO2 concentration was greatest. The presence of a biofilm demonstrated greater resiliency to high CO2 environments, compared to the conventional PBRs. However, as the PDMS model predicted, the PDMS HFMcBs did not demonstrate gas enrichment. These reactors received CO2 loading rates of 200 mg C/L*day based on PDMS permeability flux and showed approximately 65% removal of the total C transferred across the membrane. Thus, the HFMcBs demonstrated controlled carbonation of the bulk liquid via a nonporous HF membrane. Likewise, the experimental PU HFMcB did not show gas enrichment yet this result should be further explored due to the high permeability selectivity of the polymeric material. Chemical stratifications, namely pH and dissolved O2, present in a PDMS membrane-carbonated biofilm were analyzed using electrochemical microsensors. Results indicated that high DO (20 mg L-1) exists at surface of the biofilm where light availability is greatest and low pH microenvironments (pH=5.40) exist deep in the biofilm where the diffusive flux of CO2 drives transfer through the biofilm. The presence of a 400-600 ¿m liquid phase boundary layer was evident from microsensor profiles. Cryosectioning of the biofilm samples showed the biofilm to be approximately 1.17 ± 0.07 mm thick, suggesting that the high localized concentration of biomass associated with the phototrophic biofilm aided in overcoming inhibition in a microenvironment dominated by CO2(aq). Challenges of biofilm detachment and PBR fouling as well as microalgal growth inhibition in the presence of high CO2 content remain for applications of microalgae for biogas enrichment.

Late Holocene air temperature variability reconstructed from the sediments of Laguna Escondida, Patagonia, Chile (45 degrees 30 ' S)

Climate and environmental reconstructions from natural archives are important for the interpretation of current climatic change. Few quantitative high-resolution reconstructions exist for South America which is the only land mass extending from the tropics to the southern high latitudes at 56°S. We analyzed sediment cores from two adjacent lakes in Northern Chilean Patagonia, Lago Castor (45°36′S, 71°47′W) and Laguna Escondida (45°31′S, 71°49′W). Radiometric dating (210Pb, 137Cs, 14C-AMS) suggests that the cores reach back to c. 900 BC (Laguna Escondida) and c. 1900 BC (Lago Castor). Both lakes show similarities and reproducibility in sedimentation rate changes and tephra layer deposition. We found eight macroscopic tephras (0.2–5.5 cm thick) dated at 1950 BC, 1700 BC, at 300 BC, 50 BC, 90 AD, 160 AD, 400 AD and at 900 AD. These can be used as regional time-synchronous stratigraphic markers. The two thickest tephras represent known well-dated explosive eruptions of Hudson volcano around 1950 and 300 BC. Biogenic silica flux revealed in both lakes a climate signal and correlation with annual temperature reanalysis data (calibration 1900–2006 AD; Lago Castor r = 0.37; Laguna Escondida r = 0.42, seven years filtered data). We used a linear inverse regression plus scaling model for calibration and leave-one-out cross-validation (RMSEv = 0.56 °C) to reconstruct sub decadal-scale temperature variability for Laguna Escondida back to AD 400. The lower part of the core from Laguna Escondida prior to AD 400 and the core of Lago Castor are strongly influenced by primary and secondary tephras and, therefore, not used for the temperature reconstruction. The temperature reconstruction from Laguna Escondida shows cold conditions in the 5th century (relative to the 20th century mean), warmer temperatures from AD 600 to AD 1150 and colder temperatures from AD 1200 to AD 1450. From AD 1450 to AD 1700 our reconstruction shows a period with stronger variability and on average higher values than the 20th century mean. Until AD 1900 the temperature values decrease but stay slightly above the 20th century mean. Most of the centennial-scale features are reproduced in the few other natural climate archives in the region. The early onset of cool conditions from c. AD 1200 onward seems to be confirmed for this region.

Myoblast-seeded biodegradable scaffolds to prevent post-myocardial infarction evolution toward heart failure

OBJECTIVE(S): Even though the mechanism is not clearly understood, direct intramyocardial cell transplantation has demonstrated potential to treat patients with severe heart failure. We previously reported on the bioengineering of myoblast-based constructs. We investigate here the functional outcome of infarcted hearts treated by implantation of myoblast-seeded scaffolds. METHODS: Adult Lewis rats with echocardiography-confirmed postinfarction reduced ejection fraction (48.3% +/- 1.1%) were randomized to (1) implantation of myoblast-seeded polyurethane patches at the site of infarction (PU-MyoB, n = 11), (2) implantation of nonseeded polyurethane patches (PU, n = 11), (3) sham operation (Sham, n = 12), and (4) direct intramyocardial myoblast injection (MyoB, n = 11). Four weeks later, the functional assessment by echocardiography was repeated, and we additionally performed left ventricular catheterization plus histologic studies. RESULTS: The ejection fraction significantly decreased in the PU (39.1% +/- 2.3%; P = .02) and Sham (39.9% +/- 3.5%; P = .04) groups, whereas it remained stable in the PU-MyoB (48.4% +/- 3.1%) and MyoB (47.9% +/- 3.0%) groups during the observation time. Similarly, left ventricular contractility was significantly higher in groups PU-MyoB (4960 +/- 266 mm Hg/s) and MyoB (4748 +/- 304 mm Hg/s) than in groups PU (3909 +/- 248 mm Hg/s, P = .01) and Sham (4028 +/- 199 mm Hg/s, P = .01). Immunohistology identified a high density of myoblasts within the seeded scaffolds without any migration toward the host cardiac tissue and no evidence of cardiac cell differentiation. CONCLUSIONS: Myoblast-seeded polyurethane scaffolds prevent post-myocardial infarction progression toward heart failure as efficiently as direct intramyocardial injection. The immunohistologic analysis suggests that an indirect mechanism, potentially a paracrine effect, may be assumed.

Fabrication of nanoparticles by short-distance sputter deposition

During the past decades, tremendous research interests have been attracted to investigate nanoparticles due to their promising catalytic, magnetic, and optical properties. In this thesis, two novel methods of nanoparticle fabrication were introduced and the basic formation mechanisms were studied. Metal nanoparticles and polyurethane nanoparticles were separately fabricated by a short-distance sputter deposition technique and a reactive ion etching process. First, a sputter deposition method with a very short target-substrate distance is found to be able to generate metal nanoparticles on the glass substrate inside a RIE chamber. The distribution and morphology of nanoparticles are affected by the distance, the ion concentration and the process time. Densely-distributed nanoparticles of various compositions are deposited on the substrate surface when the target-substrate distance is smaller than 130mm. It is much less than the atoms’ mean free path, which is the threshold in previous research for nanoparticles’ formation. Island structures are formed when the distance is increased to 510mm, indicating the tendency to form continuous thin film. The trend is different from previously-reported sputtering method for nanoparticle fabrication, where longer distance between the target and the substrate facilitates the formation of nanoparticle. A mechanism based on the seeding effect of the substrate is proposed to interpret the experimental results. Secondly, in polyurethane nanoparticles’ fabrication, a mechanism is put forward based on the microphase separation phenomenon in block copolymer thin film. The synthesized polymers have formed dispersed and continuous phases because of the different properties between segments. With harder mechanical property, the dispersed phase is remained after RIE process while the continuous phase is etched away, leading to the formation of nanoparticles on the substrate. The nanoparticles distribution is found to be affected by the heating effect, the process time and the plasma power. Superhydrophilic property is found on samples with these two types of nanoparticles. The relationship between the nanostructure and the hydrophilicity is studied for further potential applications.

Finite element study on fracture patterns in human scaphoid wrist bone due to free fall

Scaphoid is one of the 8 carpal bones found adjacent to the thumb supported proximally by Radius bone. During the free fall, on outstretched hand, the impact load gets transferred to the scaphoid at its free anterior end. Unique arrangement of other carpal bones in the palm is also one of the reasons for the load to get transferred to scaphoid. About half of the total load acting upon carpal bone gets transferred to scaphoid at its distal pole. There are about 10 to 12 clinically observed fracture pattern in the scaphoid due to free fall. The aim of the study is to determine the orientation of the load, magnitude of the load and the corresponding fracture pattern. This study includes both static and dynamic finite element models validated by experiments. The scaphoid model has been prepared from CT scans of a 27 year old person. The 2D slices of the CT scans have been converted to 3D model by using MIMICS software. There are four cases of loading studied which are considered to occur clinically more frequently. In case (i) the load is applied at the posterior end at distal pole whereas in case (ii), (iii) and (iv), the load is applied at anterior end at different directions. The model is given a fixed boundary condition at the region which is supported by Radius bone during the impact. Same loading and boundary conditions have been used in both static and dynamic explicit finite element analysis. The site of fracture initiation and path of fracture propagation have been identified by using max principal stress / gradient and max principal strain / gradient criterion respectively in static and dynamic explicit finite element analysis. Static and dynamic impact experiments were performed on the polyurethane foam specimens to validate the finite element results. Experimental results such as load at fracture, site of fracture initiation and path of fracture propagation have been compared with the results of finite element analysis. Four different types of fracture patterns observed in clinical studies have been identified in this study.

Effect of reduced oxygen tension and long-term mechanical stimulation on chondrocyte-polymer constructs

We have investigated the influence of long-term confined dynamic compression and surface motion under low oxygen tension on tissue-engineered cell-scaffold constructs. Porous polyurethane scaffolds (8 mm x 4 mm) were seeded with bovine articular chondrocytes and cultured under normoxic (21% O(2)) or hypoxic (5% O(2)) conditions for up to 4 weeks. By means of our joint-simulating bioreactor, cyclic axial compression (10-20%; 0.5 Hz) was applied for 1 h daily with a ceramic ball, which simultaneously oscillated over the construct surface (+/-25 degrees; 0.5 Hz). Culture under reduced oxygen tension resulted in an increase in mRNA levels of type II collagen and aggrecan, whereas the expression of type I collagen was down-regulated at early time points. A higher glycosaminoglycan content was found in hypoxic than in normoxic constructs. Immunohistochemical analysis showed more intense type II and weaker type I collagen staining in hypoxic than in normoxic cultures. Type II collagen gene expression was slightly elevated after short-term loading, whereas aggrecan mRNA levels were not influenced by the applied mechanical stimuli. Of importance, the combination of loading and low oxygen tension resulted in a further down-regulation of collagen type I mRNA expression, contributing to the stabilization of the chondrocytic phenotype. Histological results confirmed the beneficial effect of mechanical loading on chondrocyte matrix synthesis. Thus, mechanical stimulation combined with low oxygen tension is an effective tool for modulating the chondrocytic phenotype and should be considered when chondrocytes or mesenchymal stem cells are cultured and differentiated with the aim of generating cartilage-like tissue in vitro.

Quantifying the influence of bone density and thickness on resonance frequency analysis: an in vitro study of biomechanical test materials

PURPOSE: Resonance frequency analysis (RFA) offers the opportunity to monitor the osseointegration of an implant in a simple, noninvasive way. A better comprehension of the relationship between RFA and parameters related to bone quality would therefore help clinicians improve diagnoses. In this study, a bone analog made from polyurethane foam was used to isolate the influences of bone density and cortical thickness in RFA. MATERIALS AND METHODS: Straumann standard implants were inserted in polyurethane foam blocks, and primary implant stability was measured with RFA. The blocks were composed of two superimposed layers with different densities. The top layer was dense to mimic cortical bone, whereas the bottom layer had a lower density to represent trabecular bone. Different densities for both layers and different thicknesses for the simulated cortical layer were tested, resulting in eight different block combinations. RFA was compared with two other mechanical evaluations of primary stability: removal torque and axial loading response. RESULTS: The primary stability measured with RFA did not correlate with the two other methods, but there was a significant correlation between removal torque and the axial loading response (P < .005). Statistical analysis revealed that each method was sensitive to different aspects of bone quality. RFA was the only method able to detect changes in both bone density and cortical thickness. However, changes in trabecular bone density were easier to distinguish with removal torque and axial loading than with RFA. CONCLUSIONS: This study shows that RFA, removal torque, and axial loading are sensitive to different aspects of the bone-implant interface. This explains the absence of correlation among the methods and proves that no standard procedure exists for the evaluation of primary stability.

3D scaffolds co-seeded with human endothelial progenitor and mesenchymal stem cells: evidence of prevascularisation within 7 days

Blood supply is a critical issue in most tissue engineering approaches for large defect healing. As vessel ingrowth from surrounding tissues is proven to be insufficient, current strategies are focusing on the neo-vascularisation process. In the present study, we developed an in vitro pre-vascularised construct using 3D polyurethane (PU) scaffolds, based on the association of human Endothelial Progenitor Cells (EPC, CD34+ and CD133+) with human Mesenchymal Stem Cells (MSC). We showed the formation of luminal tubular structures in the co-seeded scaffolds as early as day 7 in culture. These tubular structures were proven positive for endothelial markers von Willebrand Factor and PECAM-1. Of special significance in our constructs is the presence of CD146-positive cells, as a part of the neovasculature scaffolding. These cells, coming from the mesenchymal stem cells population (MSC or EPC-depleted MSC), also expressed other markers of pericyte cells (NG2 and αSMA) that are known to play a pivotal function in the stabilisation of newly formed pre-vascular networks. In parallel, in co-cultures, osteogenic differentiation of MSCs occurred earlier when compared to MSCs monocultures, suggesting the close cooperation between the two cell populations. The presence of angiogenic factors (from autologous platelet lysates) in association with osteogenic factors seems to be crucial for both cell populations' cooperation. These results are promising for future clinical applications, as all components (cells, growth factors) can be prepared in an autologous way.