Estudo dos parâmetros operacionais do processo de combustão in situ em reservatório de petróleo pesado

The occurrence of heavy oil reservoirs have increased substantially and, due to the high viscosity characteristic of this type of oil, conventional recovery methods can not be applied. Thermal methods have been studied for the recovery of this type of oil, with a main objective to reduce its viscosity, by increasing the reservoir temperature, favoring the mobility of the oil and allowing an increasing in the productivity rate of the fields. In situ combustion (ISC) is a thermal recovery method in which heat is produced inside the reservoir by the combustion of part of the oil with injected oxygen, contrasting with the injection of fluid that is heated in the surface for subsequent injection, which leads to loss heat during the trajectory to the reservoir. The ISC is a favorable method for recovery of heavy oil, but it is still difficult to be field implemented. This work had as an objective the parametric analysis of ISC process applied to a semi-synthetic reservoir with characteristics of the Brazilian Northeast reservoirs using vertical production and vertical injection wells, as the air flow injection and the wells completions. For the analysis, was used a commercial program for simulation of oil reservoirs using thermal processes, called Steam, Thermal and Advanced Processes Reservoir Simulator (STARS) from Computer Modelling Group (CMG). From the results it was possible to analyze the efficiency of the ISC process in heavy oil reservoirs by increasing the reservoir temperature, providing a large decrease in oil viscosity, increasing its mobility inside the reservoir, as well as the improvement in the quality of this oil and therefore increasing significantly its recovered fraction. Among the analyzed parameters, the flow rate of air injection was the one which had greater influence in ISC, obtaining higher recovery factor the higher is the flow rate of injection, due to the greater amount of oxygen while ensuring the maintenance of the combustion front

Desenvolvimento de uma unidade pirolítica com reator de cilindro rotativo: obtenção de bio-óleo

The demand for alternative sources of energy drives the technological development so that many fuels and energy conversion processes before judged as inadequate or even non-viable, are now competing fuels and so-called traditional processes. Thus, biomass plays an important role and is considered one of the sources of renewable energy most important of our planet. Biomass accounts for 29.2% of all renewable energy sources. The share of biomass energy from Brazil in the OIE is 13.6%, well above the world average of participation. Various types of pyrolysis processes have been studied in recent years, highlighting the process of fast pyrolysis of biomass to obtain bio-oil. The continuous fast pyrolysis, the most investigated and improved are the fluidized bed and ablative, but is being studied and developed other types in order to obtain Bio-oil a better quality, higher productivity, lower energy consumption, increased stability and process reliability and lower production cost. The stability of the product bio-oil is fundamental to designing consumer devices such as burners, engines and turbines. This study was motivated to produce Bio-oil, through the conversion of plant biomass or the use of its industrial and agricultural waste, presenting an alternative proposal for thermochemical pyrolysis process, taking advantage of particle dynamics in the rotating bed that favors the right gas-solid contact and heat transfer and mass. The pyrolyser designed to operate in a continuous process, a feeder containing two stages, a divisive system of biomass integrated with a tab of coal fines and a system of condensing steam pyrolytic. The prototype has been tested with sawdust, using a complete experimental design on two levels to investigate the sensitivity of factors: the process temperature, gas flow drag and spin speed compared to the mass yield of bio-oil. The best result was obtained in the condition of 570 oC, 25 Hz and 200 cm3/min, temperature being the parameter of greatest significance. The mass balance of the elementary stages presented in the order of 20% and 37% liquid pyrolytic carbon. We determined the properties of liquid and solid products of pyrolysis as density, viscosity, pH, PCI, and the composition characterized by chemical analysis, revealing the composition and properties of a Bio-oil.

Análise de viabilidade de injeção de fluidos alternativos ao vapor em reservatórios de óleo pesado

Many of hydrocarbon reserves existing in the world are formed by heavy oils (°API between 10 and 20). Moreover, several heavy oil fields are mature and, thus, offer great challenges for oil industry. Among the thermal methods used to recover these resources, steamflooding has been the main economically viable alternative. Latent heat carried by steam heats the reservoir, reducing oil viscosity and facilitating the production. This method has many variations and has been studied both theoretically and experimentally (in pilot projects and in full field applications). In order to increase oil recovery and reduce steam injection costs, the injection of alternative fluid has been used on three main ways: alternately, co-injected with steam and after steam injection interruption. The main objective of these injection systems is to reduce the amount of heat supplied to the reservoir, using cheaper fluids and maintaining the same oil production levels. This works discusses the use of carbon dioxide, nitrogen, methane and water as an alternative fluid to the steam. The analyzed parameters were oil recoveries and net cumulative oil productions. The reservoir simulation model corresponds to an oil reservoir of 100 m x 100 m x 28 m size, on a Cartesian coordinates system (x, y and z directions). It is a semi synthetic model with some reservoir data similar to those found in Brazilian Potiguar Basin. All studied cases were done using the simulator STARS from CMG (Computer Modelling Group, version 2009.10). It was found that waterflood after steam injection interruption achieved the highest net cumulative oil compared to other fluids injection. Moreover, it was observed that steam and alternative fluids, co-injected and alternately, did not present increase on profitability project compared with steamflooding

Análise paramétrica da injeção de vapor e solvente em reservatórios de óleo pesado

A significant fraction of the hydrocarbon reserves in the world is formed by heavy oils. From the thermal methods used to recovery these resources, Steamflooding has been one of the main economically viable alternatives. In Brazil, this technology is widely used by Petrobras in Northeast fields. Latent heat carried by steam heats the oil in the reservoir, reducing its viscosity and facilitating the production. In the last years, an alternative more and more used by the oil industry to increase the efficiency of this mechanism has been the addition of solvents. When co-injected with steam, the vaporized solvent condenses in the cooler regions of the reservoir and mixes with the oil, creating a low viscosity zone between the steam and the heavy oil. The mobility of the displaced fluid is then improved, resulting in an increase of oil recovery. To better understand this improved oil recovery method and investigate its applicability in reservoirs with properties similar to those found in Potiguar Basin, a numerical study was done to analyze the influence of some operational parameters (steam injection rate, injected solvent volume and solvent type) on oil recovery. Simulations were performed in STARS ("Steam, Thermal, and Advanced Processes Reservoir Simulator"), a CMG ("Computer Modelling Group") program, version 2009.10. It was found that solvents addition to the injected steam not only anticipated the heated oil bank arrival to the producer well, but also increased the oil recovery. Lower cold water equivalent volumes were required to achieve the same oil recoveries from the models that injected only steam. Furthermore, much of the injected solvent was produced with the oil from the reservoir

Estudo do acoplamento do poço injetor nas simulações de injeção cíclica de vapor

Steam injection is a method usually applied to very viscous oils and consists of injecting heat to reduce the viscosity and, therefore, increase the oil mobility, improving the oil production. For designing a steam injection project it is necessary to have a reservoir simulation in order to define the various parameters necessary for an efficient heat reservoir management, and with this, improve the recovery factor of the reservoir. The purpose of this work is to show the influence of the coupled wellbore/reservoir on the thermal simulation of reservoirs under cyclic steam stimulation. In this study, the methodology used in the solution of the problem involved the development of a wellbore model for the integration of steam flow model in injection wellbores, VapMec, and a blackoil reservoir model for the injection of cyclic steam in oil reservoirs. Thus, case studies were developed for shallow and deep reservoirs, whereas the usual configurations of injector well existing in the oil industry, i.e., conventional tubing without packer, conventional tubing with packer and insulated tubing with packer. A comparative study of the injection and production parameters was performed, always considering the same operational conditions, for the two simulation models, non-coupled and a coupled model. It was observed that the results are very similar for the specified well injection rate, whereas significant differences for the specified well pressure. Finally, on the basis of computational experiments, it was concluded that the influence of the coupled wellbore/reservoir in thermal simulations using cyclic steam injection as an enhanced oil recovery method is greater for the specified well pressure, while for the specified well injection rate, the steam flow model for the injector well and the reservoir may be simulated in a non- coupled way

Hiperidrose compensatória após simpatectomia toracoscópica: características, incidência e influência na satisfação do paciente

Hyperhidrosis is an idiopathic condition characterized by excessive sweating. Symptoms generally begin in childhood or early adolescence, and rarely improve with age. The excessive localized sweating generally occurs either spontaneously, or in association with stressful or emotionally charged situations. This prospective study aimed to investigate predictive factors for compensatory hyperhidrosis after thoracoscopic sympathicotomy. From 2000 to 2002, 80 patients (53 female and 27 male) underwent hyperhidrosis surgery. The patients, ranging from 12 to 56 years old, were studied and followed-up for 42.51 ±5.98 months. A satisfaction grading using a visual analogue scale -VAS (0 = not at all satisfied, and 10 = fully satisfied) was used. The surgical procedure was performed bilaterally on the second ganglion (T2) for facial hyperhidrosis, on the third and fourth ganglia (T3 and T4) for axillary hyperhidrosis, and on the third ganglion (T3) for palmar hyperhidrosis. The results showed that, 68 patients (85%) presented with compensatory sweating (CS), which was classified as mild (33.8%), moderate (33.8%) and severe (32.4%). Considering the final surgical results, 70 patients (87.5%) were satisfied with the outcome of the operation, while 10 patients (12.5%) were dissatisfied. Degrees of satisfaction varied according to sex, age, BMI and extent of denervation. Moreover, the compensatory hyperhidrosis was more severe in abdomen and back than in legs. In conclusion, although CS is a frequent adverse effect of sympathicotomy, the degree of patient satisfaction was high. Some factors were related to the occurrence and severity of CS and the most adequate patients to be submitted to this operation are young adult women whose BMI is less than 24.9

Desenvolvimento de Sistemas Microparticulados Superparamagnéticos Gastro-resistentes para Diagnóstico e Terapêutica

This work aimed to develop a suitable magnetic system for administration by the oral route. In addition to that, it was intended to review the current uses of magnetic systems and the safety related to magnetic field exposure. Methods: Coprecipitation and emulsification/crosslinking were carried out in order to synthesize magnetite particles and to coat them, respectively. Results: According to literature review, it was found that magnetic particles present several properties such as magnetophoresis in magnetic field gradient, production of a surrounding magnetic field, and heat generation in alternated magnetic field. When the human organism is exposed to magnetic fields, several interaction mechanisms come into play. However, biological tissues present low magnetic susceptibility. As a result, the effects are not so remarkable. Concerning the development of a magnetic system for oral route, uncoated magnetite particles did undergo significant dissolution at gastric pH. On the other hand, such process was inhibited in the xylan-coated particles. Conclusions: Due to their different properties, magnetic systems have been widely used in biosciences. However, the consequent increased human exposure to magnetic fields has been considered relatively safe. Concerning the experimental work, it was developed a polymer-coated magnetic system. It may be very promising for administration by the oral route for therapy and diagnostic applications as dissolution at gastric pH hardly took place

Impacto da atividade física na qualidade de vida em mulheres de meia idade: estudo de base populacional

Conselho Nacional de Desenvolvimento Científico e Tecnológico

Superação de dormência das sementese controle químico de plantas de Momordicacharantia L

This experiment were performed to evaluate methods of seeds scarification for overcoming dormancy and the efficacy of six herbicides registered for sugarcane to control adult plants of Mcharantia. The experimental design was completely randomized, with four replications in both trials. The first trial is a factorial 2x8 (two times of seeds collection (2006 and 2007) with eight methods of breaking dormancy (mechanical scarification; 100% and 50% concentrated sulfuric acid; 2% potassium nitrate for three and six hours; heat dried at 60 degrees C; hot water at 60 degrees C and an untreated control). In the second trial evaluated the control of M. charantia through six different herbicides: Imazapic, Metsulfuron-methyl, Metribuzin, 2,4-D, Amicarbazone, Paraquat and a control without herbicide application. Thus, it can be concluded that the seeds were immersed in concentrated sulfuric acid for three minutes and potassium nitrate for three hours gave a higher percentage and germination speed and the herbicide Metribuzin reached, albeit belatedly, a total control of M. charantia.

Crescimento inicial e morfologia foliar em plantas de Enterolobium contortisiliquum (Vell.) Morong. E Erythrina velutina Mart. ex Benth, sob estresse hídrico

The Caatinga is the predominant vegetation type in semi-arid region of Brazil, where many inhabitants depend on hunting and gathering for survival, obtaining resources for: food and feed, folk medicine, timber production, etc. It‟s the dry ecosystem with highest population density in the world. The early stages of development are the most critical during the life cycle of a flowering plant and they‟re primordial to its establishment in environments exposed to water stress. Information about adjustments to the growth of the species, correlated with their studies of distribution in Seridó oriental potiguar, are an important ecological and economic standpoint, because they provide subsidies for the development of cultivation techniques, to programs of sustainable use and recovery of degraded areas. This thesis aimed to study the initial growth and foliar morphology in plants like Enterolobium contortisiliquum (Vell.) Morong. (tamboril) and Erythrina velutina Mart. ex Benth (mulungu), species of occurrence in the Caatinga, under water stress. After sowing and emergency, the seedlings were exposed to three water regimes: 450 (control), 225 (moderate stress) and 112.5 (severe stress) mm of water slide for 40 days. Seeding occurred in bags of 5 kg and after the establishment of seedlings thinning was carried out leaving a plantlet per bag. At the beginning the waterings occurred daily with distilled water, passing to be on alternate days after thinning. Twenty and forty days after the thinning seedlings collections were held to be done analysis of growth and biomass partition. When compared to the control group, the treatments with water stress showed reduction in the growth of the aerial part, growth of the greater root, number of leaves and leaflets, dry leaf area and total phytomass in both species, but in general, this effect was most marked for E. velutina. Regarding the partition of biomass, there were few changes throughout the experiment. Morphological changes in the leaves as a function of stress were not significant, however, there was a trend, in both species, to produce narrower leaves, that facilitate heat loss to the environment. It has not been possible to establish a positive relationship between inhibition of growth and distribution of species, whereas E. velutina is a species of most common occurrence in Seridó oriental potiguar. In this way, other aspects should be taken into account when studying the adaptation of species the dry environments, such as salinity, presence of heavy metals, wind speed, etc

Métodos de superação de dormência em sementes de Ipomoea e Merremia

Este trabalho objetivou avaliar os efeitos de métodos de superação de dormência sobre a germinação das sementes de Ipomoea grandifolia, I. hederifolia, I. nil, I. quamoclit, Merremia aegyptia e M. cissoides. Os tratamentos consistiram em ácido sulfúrico concentrado, nitrato de potássio, água quente e calor seco (50 ºC), lixa e fogo. Constatou-se que o ácido sulfúrico promoveu aumento na germinação das sementes de I. grandifolia (58, 37, 22 e 34%), I. hederifolia (76, 49, 82 e 55%), I. quamoclit (43, 33, 66 e 35%), I. nil (69, 79, 72 e 62%), M. cissoides (8, 19, 35 e 57%) e M. aegyptia (24, 64, 56 e 63%) após períodos de imersão de 5, 10, 15 e 20 minutos, respectivamente. A água (20 e 40 minutos), o calor seco (20 e 40 minutos) e o fogo melhoraram a germinação de I. grandifolia (68, 59, 62, 67 e 59%), M. cissoides (50, 52, 18, 25 e 46%) e M. aegyptia (54, 47, 21, 21 e 45%), respectivamente. O calor seco de 20 e 40 minutos melhorou a germinação de I. nil (49 e 36%), e o de 40 minutos, a de I. hederifolia (70%). O uso de nitrato de potássio e lixa não proporcionou melhoria na germinação das sementes.

Validation of the Deardorff model for estimating energy balance components for a sugarcane crop

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise do resfriamento da solução nutritiva para cultivo hidropônico do morangueiro

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Ensino de Entropia: um enfoque histórico e epistemológico.

The rational construction necessary to systematize scientific knowledge in physics, introduces difficulties of understanding in some of its concepts. One of these concepts which exemplify properly this difficulty in learning or teaching is entropy. This thesis propose the construction of a didactic route which constitute itself a historical and epistemological course to entropy, intending to contribute for teaching this concept as well as other physics concepts. The basic assumption to build this route is that through the historical review of the development of this concept in the way suggested by Bachelard s (1884-1962) epistemology it is possible to make subjects, to be taught and learned, more meaningful. Initially I composed a brief biographical note to give the reader an idea about the issues, interests and reflections, related to science, and how I dealt with them in my private and professional life, as well as the role they played to lead me to write this thesis. The strategy to construct the route to entropy was to split the usual contents of basic thermodynamics in three moments in a way they can constitute epistemological units , which can be identified by the way of thinking in the corresponding moments of scientific knowledge production: a technical and empiricist moment, a rationalist and positivist moment and a post-positivist rationalist one. The transition between each moment is characterized by a rupture with the former way of thinking; however the progress in the construction of knowledge in the area is evident. As the final part of this work I present an analysis based on elements of Bachelard s epistemology that are present in each moment. This analysis is the basic component of the didactic route that I propose myself to build. The way I made this route guide to entropy could contribute to the construction of other didactic routes in physics and other sciences, in a way to unveil hidden meanings and as a tool to humanize scientific knowledge.

Características do pelame de vacas Holandesas em ambiente tropical: um estudo genético e adaptativo

As características do pelame (espessura da capa, comprimento médio dos pêlos, número de pêlos por unidade de área, densidade de massa dos pêlos, ângulo de inclinação dos pêlos com respeito a superfície da epiderme e diâmetro médio do pêlos) foram avaliadas em 973 vacas da raça Holandesa, entre novembro de 2000 e abril de 2001, numa área localizada 20cm abaixo da coluna vertebral, no centro do tronco, tanto nas malhas brancas como nas negras. As amostras de pêlos foram obtidas com um alicate comum adaptado. O método da Máxima Verossimilhança Restrita (REML) foi usado para estimar os componentes de variância e covariância sob modelo animal, sendo empregado o sistema MTDFREML. Os resultados mostraram que as características do pelame preto são diferentes das do branco, quando os animais são criados em ambiente tropical. O pelame preto apresentou-se menos denso, com pêlos mais curtos e grossos devido à maior necessidade de perder calor, enquanto que, o pelame branco é mais denso e com pêlos mais compridos, oferecendo uma melhor proteção contra à radiação solar direta. A seleção de vacas predominantemente negras pode ser uma boa escolha para aumentar a resistência do gado Holandês às condições do ambiente tropical, principalmente à radiação solar, quando esses animais são criados a campo, devido a que a epiderme sob esse tipo de malhas é altamente pigmentada. Tal seleção pode ser facilmente realizada, considerando a alta herdabilidade (h²=0,75) para a proporção de malhas negras. Esta seleção deve ser realizada no sentido de um pelame menos denso, com pêlos curtos e grossos favorecendo as perdas de calor sensível e calor latente.