EXCIMER FLUORESCENCE STUDY ON THE MISCIBILITY OF POLY(VINYL METHYL-ETHER) AND STYRENE-BUTADIENE STYRENE TRIBLOCK COPOLYMER

The excimer fluorescence of a triblock copolymer, styrene-butadiene-styrene (SBS) containing 48 wt% polystyrene was used to investigate its miscibility with poly(vinyl methyl ether) (PVME). The excimer-to-monomer emission intensity ratio I(M)/I(E) can be used as a sensitive probe to determine the miscibility level in SBS/PVME blends: I(M)/I(E) is a function of PVME concentration, and reaches a maximum when the blend contains 60% PVME. The cloud point curve determined by light scattering shows a pseudo upper critical solution temperature diagram, which can be attributed to the effect of PB segments in SBS. The thermally induced phase separation of SBS/PVME blends can be observed by measuring I(M)/I(E), and the phase dissolution process was followed by measuring I(M)/I(E) at different times.

RADIATION GRAFT COPOLYMER OF ACRYLIC-ACID ONTO EVA

The structure of the radiation graft copolymer of acrylic acid onto EVA has been studied by infrared spectroscopy and XPS. It was found that along with the main peak C there is a photoelectron peak at 288.5 eV attributed to [GRAPHICS] group in XPS spectra and the content of its area in XPS increases with increasing of grafting degree of EVA. It was also found that hydrophilicity of EVA increases with the increase of grafting degree.

XPS STUDIES ON RADIATION-INDUCED STRUCTURAL-CHANGES IN THE COPOLYMER OF TETRAFLUOROETHYLENE AND ETHYLENE

In this work, the radiation-induced structural changes in the copolymer of tetrafluoroethylene and ethylene (F-40) were studied by X-ray photoelectron spectroscopy (XPS). During irradiation, some CF2 groups in the polymer were found to have been converted into carbon structures that bonded indirectly with fluorine atoms.

RADIATION STABILITY OF PERFLUOROETHYLENE PROPYLENE COPOLYMER

The gel content of crosslinked perfluoroethylene-propylene copolymer was obtained by extraction with fluoro-chloro oil. It was then treated by the Charlesby-Pinner equation. The results obtained revealed that both the gelation dose and the ratio of fracture to crosslinking density decreased with increasing irradiation temperature.

SEQUENCE STRUCTURE OF ETHYLENE-VINYL SUBSTITUTED COPOLYMER WITH C-13 NMR .4.

The substituent chemical shift (SCS) has been applied to the assignment of the C-13 NMR spectrum of chlorinated polyethylene (CPE). CPE of different chlorine contents has been employed and their sequence structure discussed. The results show that characteristic of CPE with medium chlorine content is the dichloroethane structure in molecular chain. SCS parameters have been obtained from the C-13 NMR spectra. It was found that the effects of chlorine content and temperature on SCS are negligible, but the substituent parameter S1 reduced by 0.39 ppm when C2Cl4 was added to solvent ODCB.

STUDIES ON RADIATION-INDUCED LOSS OF WEIGHT OF A COPOLYMER OF TETRAFLUOROETHYLENE AND HEXAFLUOROPROPYLENE

The radiation-induced loss of weight of F-46 was found to be proportional to irradiation dose and affected markedly by irradiation temperature.

XPS STUDY OF RADIATION CROSS-LINKED COPOLYMER OF TETRAFLUOROETHYLENE WITH HEXAFLUOROPROPYLENE

In this work the radiation-induced structural changes in F-46 were studied by XPS. In carbon-1s spectra of a highly crosslinked F-46 sheet, the slight increase observed in relative area under the peak due to CF3 was explained by the radiation-induced scission of polymer chains. The peak at 287.6 eV appearing in the spectra caused by ionizing radiation was attributed to carbon structures without primary fluorine substituents, in both branching and unsaturated structures, while that at 289.3 eV was assigned to = CF groups in mid-chain double bonds.

STRUCTURE AND PROPERTIES OF SEQUENTIALLY POLYMERIZED PROPYLENE-B-[ETHYLENE-CO-PROPYLENE]-B-PROPYLENE COPOLYMERS

The structure and properties of presumed block copolymers of polypropylene (PP) with ethylene-propylene random copolymers (EPR), i.e., PP-EPR and PP-EPR-PP, have been investigated by viscometry, transmission electron microscopy, dynamic mechanical analysis, differential scanning calorimetry, gel permeation chromatography, wide-angle x-ray diffraction, and other techniques testing various mechanical properties. PP-EPR and PP-EPR-PP were synthesized using delta-TiCl3-Et2AlCl as a catalyst system. The results indicate that the intrinsic viscosity of these polymers increases with each block-building step, whereas the intrinsic viscosity of those prepared by chain transfer reaction (strong chain-transfer reagent hydrogen was introduced between block-building steps during polymerization) hardly changes with the reaction time. Compared with PP / EPR blends, PP-EPR-PP block copolymers have lower PP and polyethylene crystallinity, and lower melting and crystallization temperatures of crystalline EPR. Two relaxation peaks of PP and EPR appear in the dynamic spectra of blends. They merge into a very broad relaxation peak with block sequence products of the same composition, indicating good compatibility between PP and EPR in the presence of block copolymers. Varying the PP and EPR content affects the crystallinity, density, and morphological structure of the products, which in turn affects the tensile strength and elongation at break. Because of their superior mechanical properties, sequential polymerization products containing PP-EPR and PP-EPR-PP block copolymers may have potential as compatibilizing agents for isotactic polypropylene and polyethylene blends or as potential heat-resistant thermoplastic elastomers.

SEM STUDY ON FRACTURE-BEHAVIOR OF ETHYLENE/PROPYLENE BLOCK COPOLYMERS AND THEIR BLENDS

The toughening effect of the separate phases of ethylene/propylene block copolymers and their blends was studied by scanning electron microscopy (SEM). The results obtained show that the interfacial adhesion between separate phases and the isotactic polypropene (iPP) matrix in ethylene/propylene block copolymers is strong at room temperature, but poor at low temperature; specimens exhibit tearing of separate phases during fracture at room temperature, but interfacial fracture between separate phases and the iPP matrix at low temperature. From the characteristics of fractographs of ethylene/propylene block copolymers and their blends, it could be concluded that the separate phases improve the toughness of specimens in several ways: they promote the plastic deformation of the iPP, and they can be deformed and fractured themselves during the fracture process. However, it was shown that the plastic deformation processes, such as multiple-crazing, shear yielding, etc. of the matrix are the dominant mechanisms of energy absorption in highly toughened ethylene/propylene block copolymers and their blends. The deformation and fracture of separate phases are only of secondary importance.

WATER-SOLUBLE AND AMPHIPHILIC POLYMERS .6. A STUDY ON THE SURFACE-COMPOSITION OF CAST FILMS OF PST/PMAA AND PEO-PST-PEO BLOCK POLYMERS BY XPS

Thin films of PSt/PMAA and PEO-PSt-PEO block polymers were deposited on a polystyrene substrate by solution adsorption (with or without solvent treatment), and the film surfaces were characterized by means of XPS. Direct solvent - casting of PEO-PSt-PEO from benzene solutions resulted in PSt-rich surfaces, whereas PMAA richer surfaces were obtained for PSt/PMAA films cast from DMF solutions. Moreover, solvent treatment after casting had profound effect on the film surface composition. Treatment with water markedly increased the surface concentration of polar PEO segments. In the case of PSt-PMAA block polymers, the PSt content on the surface increased in the order of water < ethanol < cyclohexane < petroleum ether, the last-named giving films with almost pure PSt surface. It is well worth noticing that the bulk composition had little to do with the surface composition for both PSt/PMAA and PEO-PSt-PEO block polymers within the composition range investigated when subsequent solvent treatment was applied.