Effect of bismuth oxide on the thermal stability and Judd-Ofelt parameters of Er 3(+)/Yb3(+) co-doped aluminophosphate glasses

The Er3+/Yb3+ co-doped glasses with compositions of xBi(2)O(3)-(65-x)P2O5-4Yb(2)O(3)-11Al(2)O(3)-5BaO-15Na(2)O (where x = 0, 2.5, 5, 7.5 and 10 mol%) were prepared using the normal melt quench technique. The optical absorption spectra of the glasses were recorded in the wavelength range 300-1700 nm. The effect of Bi2O3 content on the thermal stability and absorption spectra of glasses was investigated. In addition, the Judd-Ofelt parameters and oscillator strengths were calculated by employing Judd-Ofelt theory. It was observed that the positions of the fundamental absorption edge and cut-off wavelength shifted towards red as the content of Bi2O3 increased. However, there were no red shifts found both in the peak wavelength and in the center of mass wavelength of all absorption bands with Bi2O3 content increasing. The results of Judd-Ofelt theory analysis showed that Judd-Ofelt parameters Omega(t), (t = 2, 4, 6) changed sharply when Bi2O3 concentration exceeded 5 mol%. The variation trends of experimental oscillator strength were similar with those of Judd-Ofelt parameters as function of Bi2O3 concentrations. Moreover, differential scanning calorimetry experiments showed that the increases of Bi2O3 content weakened the network structure and then lowered the thermal stability of the glasses. The spontaneous emission probability A(rad), branching ratio beta and the radiative lifetime tau(rad) were also calculated and analyzed. The stimulated emission cross-section of Er3+ was calculated according to the McCumber theory. It was found that the stimulated emission cross-section of Er3+ was monotonically increases with Bi2O3 content increasing. (C) 2006 Elsevier B.V. All rights reserved.

Effect of processing parameters on the optical properties of TiO2/ormosil planar waveguide

Hybrid TiO2/ormosil waveguiding films have been prepared by the sol-gel method at low thermal treatment temperature of 150° C. The influence of processing parameters including the molar ratios of titanium butoxide (Ti(OBu)(4))/3-glycidoxypropyltrimethoxysilane (GLYMO) and H2O/Ti(OBu)(4) (expressed as R), especially aging of sot on the optical properties was investigated. The optical properties of films were measured with scanning electron microscope (SEM), UV/VIS/NIR spectrophotometer (UV-Vis), m-line and the scattering-detection method. The results indicate that the film thickness increases with the increase of sol aging time, but the variation of refractive index as a function of sot aging time depends on the relative ratios of GLYMO to Ti(OBu)(4). Higher transmittance and lower attenuation of the planar waveguide can be obtained in the sol with lower Ti(OBu)(4) contents and shorter aging time.

Avaliação da ingestão habitual de cálcio e sua associação com a concentração intracelular de cálcio, adiposidade corporal, perfil metabólico, biomarcadores inflamatórios, pressão arterial e função endotelial

A associação inversa da ingestão de cálcio dietético com adiposidade corporal e pressão arterial está documentada em estudos epidemiológicos. Achados experimentais sugerem que este fenômeno pode ser mediado por alterações na concentração intracelular de cálcio ([Ca]i). Existem poucos estudos relacionando o cálcio dietético com a [Ca]i. O objetivo do presente estudo foi avaliar a relação da ingestão habitual de cálcio dietético com a [Ca]i, adiposidade corporal, perfil metabólico, biomarcadores inflamatórios, pressão arterial e função endotelial em mulheres. Para tanto, foi desenvolvido estudo transversal, com 76 mulheres na pré-menopausa submetidas à avaliação: dietética (questionário de frequência alimentar validado); da [Ca]i em eritrócitos (espectrometria de absorbância atômica); da gordura corporal (GC) total [índice de massa corporal (IMC) e % GC por bioimpedância elétrica] e central [perímetro da cintura (PC), e razão cintura quadril (RCQ)]; do perfil metabólico (glicose, colesterol e frações, insulina e HOMA-IR); dos biomarcadores inflamatórios [adiponectina e proteína C-reativa (PCR)]; dos biomarcadores da função endotelial [molécula de adesão intracelular-1 (ICAM-1), molécula de adesão celular vascular-1 (VCAM-1) e E-Selectina]; da função endotelial avaliada pelo equipamento Endo-PAT2000; e da pressão arterial. Calcitriol, paratormônio, cálcio sérico e cálcio urinário completaram o metabolismo do cálcio. As participantes foram estratificadas em 2 grupos de acordo com a ingestão habitual de cálcio: Grupo com baixa ingestão de cálcio ou BIC (n=32; ingestão de cálcio <600mg/d) e Grupo com elevada ingestão de cálcio ou AIC (n=44; ingestão de cálcio ≥600mg/d). A média da idade foi semelhante entre os grupos (Grupo BIC: 31,41,4 vs Grupo AIC: 31,41,4anos; p=0,99). Após ajustes para fatores de confundimento (idade, ingestão de energia, bebida alcoólica, proteína, carboidratos e lipídios), o Grupo AIC, em comparação com o BIC, apresentou valores significativamente mais baixos de IMC (25,65,3 vs 26,9 6,0 kg/m; p=0,02), PC (84,413,6 vs 87,815,3cm; p=0,04), % GC (31,15,9 vs 33,35,6 %; p=0,003), pressão arterial diastólica (68,210,8 vs 72,411,2 mm Hg; p=0,04) e pressão arterial média (80,1310,94 vs 83,8611,70 mmHg; p=0,04); e significativamente mais altos de HDL-colesterol (58,612,2 vs 52,912,2 mg/dL; p=0,004) e adiponectina (34572,1 19472,8 vs 31910,319385,1 ng/mL; p=0,05). A [Ca]i e as outras variáveis avaliadas não diferiram entre os grupos, mesmo após ajustes. Neste estudo realizado com mulheres, o maior consumo de cálcio se associou com valores mais baixos de adiposidade corporal total e central, pressão arterial diastólica e média; além de valores mais elevados de HDL-colesterol e adiponectina

Dealing with the Effects of Sensor Displacement in Wearable Activity Recognition

Most wearable activity recognition systems assume a predefined sensor deployment that remains unchanged during runtime. However, this assumption does not reflect real-life conditions. During the normal use of such systems, users may place the sensors in a position different from the predefined sensor placement. Also, sensors may move from their original location to a different one, due to a loose attachment. Activity recognition systems trained on activity patterns characteristic of a given sensor deployment may likely fail due to sensor displacements. In this work, we innovatively explore the effects of sensor displacement induced by both the intentional misplacement of sensors and self-placement by the user. The effects of sensor displacement are analyzed for standard activity recognition techniques, as well as for an alternate robust sensor fusion method proposed in a previous work. While classical recognition models show little tolerance to sensor displacement, the proposed method is proven to have notable capabilities to assimilate the changes introduced in the sensor position due to self-placement and provides considerable improvements for large misplacements.

Avaliação da remoção do íon cádmio em solução aquosa utilizando processos de osmose inversa e nanofiltração

Os efluentes contendo cádmio podem ser gerados dos por várias indústrias. A aplicação de ambas as tecnologias osmose inversa (OI) e nanofiltração (NF) para o tratamento de efluentes contendo o íon cádmio para reduzir a degradação ambiental foram estudadas no presente trabalho. Amostras sintéticas contendo o íon cádmio em várias concentrações foram preparadas e submetidas aos tratamentos por OI e NF em escala laboratorial. Assim, dividiu-se o processo de remoção em três etapas: 1- analisou-se os processos de osmose inversa e nanofiltração em termos da rejeição do íon cádmio, onde se correlacionou e avaliou os principais parâmetros de processos (concentração da solução alimentação, fluxo de permeado e pressão) e comparou-se os sistemas entre si. Nas etapas 2 e 3 avaliou-se os efeitos da salinidade utilizando os contra-íons zinco e sódio respectivamente, sobre a rejeição do íon cádmio no sistema de osmose inversa em soluções aquosas contendo misturas de sulfato de cádmio e sulfato de zinco, e sulfato de cádmio e sulfato de sódio. Mediu-se as concentrações de cádmio e zinco por espectroscopia de absorção atômica e as concentrações de sulfato e sódio por cromatografia de íons. Os resultados obtidos na primeira etapa dos experimentos mostram que a osmose inversa e nanofiltração são eficientes na remoção de cádmio, onde se obteve as taxas médias de rejeição de 92,4% e 96,6% respectivamente, sendo esses valores iguais em magnitude, tendo em vista os valores da incerteza padrão relativa associada a esses resultados. Em ambos os sitemas, os fluxos de permeado e as rejeições não sofreram influência do aumento da concentração de cádmio na solução alimentação.Na etapa 2, os resultados mostraram a diminuição da rejeição de cádmio com o aumento da concentração de sulfato de zinco na alimentação, sendo esse fenômeno atribuído a semelhança existente entre os íons Cd2+ e Zn2+ associados aos seus raios iônicos de hidratação e as energias de hidratação. Foram observadas as quedas do fluxo de permeado e das rejeições com o aumento da concentração de alimentação provavelmente devido ao efeito da polarização. Na etapa 3, a rejeição do íon cádmio não foi afetada pelo aumento da concentração de sulfato de sódio na alimentação, assim como os fluxos de permeado. Outro aspecto relacionado à rejeição é que a difusão do sódio através da membrana é favorecida frente à difusão do cádmio, sendo atribuído ao menor raio de hidratação do sódio

Estimation of the growth curve parameters in Macrobrachium rosenbergii

Growth is one of the most important characteristics of cultured species. The objective of this study was to determine the fitness of linear, log linear, polynomial, exponential and Logistic functions to the growth curves of Macrobrachium rosenbergii obtained by using weekly records of live weight, total length, head length, claw length, and last segment length from 20 to 192 days of age. The models were evaluated according to the coefficient of determination (R2), and error sum off square (ESS) and helps in formulating breeders in selective breeding programs. Twenty full-sib families consisting 400 PLs each were stocked in 20 different hapas and reared till 8 weeks after which a total of 1200 animals were transferred to earthen ponds and reared up to 192 days. The R2 values of the models ranged from 56 – 96 in case of overall body weight with logistic model being the highest. The R2 value for total length ranged from 62 to 90 with logistic model being the highest. In case of head length, the R2 value ranged between 55 and 95 with logistic model being the highest. The R2 value for claw length ranged from 44 to 94 with logistic model being the highest. For last segment length, R2 value ranged from 55 – 80 with polynomial model being the highest. However, the log linear model registered low ESS value followed by linear model for overall body weight while exponential model showed low ESS value followed by log linear model in case of head length. For total length the low ESS value was given by log linear model followed by logistic model and for claw length exponential model showed low ESS value followed by log linear model. In case of last segment length, linear model showed lowest ESS value followed by log linear model. Since, the model that shows highest R2 value with low ESS value is generally considered as the best fit model. Among the five models tested, logistic model, log linear model and linear models were found to be the best models for overall body weight, total length and head length respectively. For claw length and last segment length, log linear model was found to be the best model. These models can be used to predict growth rates in M. rosenbergii. However, further studies need to be conducted with more growth traits taken into consideration

Growth and spectroscopic characteristics of Yb : GSO single crystal

For the first time, a high optical quality 10 at.% Yb3+-doped gadolinium oxyorthosilicate laser crystal Gd2SiO5 (GSO) was grown by the Czochralski (Cz) method. The segregation coefficient of Yb3+ was studied by the inductively coupled plasma atomic emission spectrometer (ICP-AES) method. The crystal structure has monoclinic symmetry with space group P2(1)/c; this was determined by means of an x-ray diffraction analysis. The absorption spectra, fluorescence spectra and fluorescence decay curves of Yb3+ ions in a GSO crystal at room temperature were also studied. Then, the spectroscopic parameters of Yb:GSO were calculated. The advantages of the Yb:GSO crystal include high crystal quality, quasi-four-level laser operating scheme, high absorption cross-sections and particularly broad emission bandwidth (similar to 72 nm). The results indicated that the Yb:GSO crystal seemed to be a very promising laser gain medium in diode-pumped femtosecond laser and tunable solid state laser applications when LD pumped at 940 and 980 nm.

Comparison of spectroscopic parameters of 15 at% Yb : YAlO3 and 15 at% Yb : Y3Al5O12

Yb: YAlO3 (YAP) (15 at %) and Yb: Y3Al5O12 (YAG)(15 at %) have been grown using the Czochralski method. Their absorption and fluorescence spectra were measured at room temperature and important spectroscopic parameters were calculated. Through the comparison of spectroscopic parameters of Yb:YAP and Yb: YAG, all results indicate that 15 at % Yb:YAP crystal is a potential candidate used for compact, efficient thin chip lasers when the laser output wavelength is 1012 or 103 8 nm. (C) 2004 Elsevier B.V. All rights reserved.

Yb：FAP晶体的生长及光谱性能

应用中频感应提拉法生长出不同掺杂浓度的Yb：FAP激光晶体，运用电感耦合等离子体原子发射光谱仪（ICP-AES）测定了Yb^3＋离子存Yb：FAP晶体中的分凝系数约为0．03。随着晶体的生长，晶体中Yb^3＋离子的轴向浓度逐渐增大。研究Yb：FAP晶体在77K和300K温度下的吸收光谱发现，振动谱的变化主要是由电子-声子近共振耦合作用引起的。系统地研究了不同Yb^3＋离子掺杂浓度Yb：FAP晶体的吸收光谱和荧光光谱。通过吸收光谱的测量计算了晶体的吸收截面。Yb：FAP晶体在904nm和982nm处存在Yb