Fatigue resistance of denture teeth

AIMS: There is no standard test to determine the fatigue resistance of denture teeth. With the increasing number of patients with implant-retained dentures the mechanical strength of the denture teeth requires more attention and valid laboratory test set-ups. The purpose of the present study was to determine the fatigue resistance of various denture teeth using a dynamic load testing machine. METHODS: Four denture teeth were used: Bonartic II (Candulor), Physiodens (Vita), SR Phonares II (Ivoclar Vivadent) and Trubyte (Dentsply). For dynamic load testing, first upper molars with a similar shape and cusp inclination were selected. The molar teeth were embedded in cylindrical steel molds with denture base material (ProBase, Ivoclar Vivadent). Dynamic fatigue loading was carried out on the mesio-buccal cusp at a 45° angle using dynamic testing machines and 2,000,000 cycles at 2Hz in water (37°C). Three specimens per group and load were submitted to decreasing load levels (at least 4) until all the three specimens no longer showed any failures. All the specimens were evaluated under a stereo microscope (20× magnification). The number of cycles reached before observing a failure, and its dependence on the load and on the material, has been modeled using a parametric survival regression model with a lognormal distribution. This allowed to estimate the fatigue resistance for a given material as the maximal load for which one would observe less than 1% failure after 2,000,000 cycles. RESULTS: The failure pattern was similar for all denture teeth, showing a large chipping of the loaded mesio-buccal cusp. In our regression model, there were statistically significant differences among the different materials, with SR Phonares II and Bonartic II showing a higher resistance than Physiodens and Trubyte, the fatigue resistance being estimated at around 110N for the former two, and at about 60N for the latter two materials. CONCLUSION: The fatigue resistance may be a useful parameter to assess and to compare the clinical risk of chipping and fracture of denture tooth materials.

Validation of a computer-assisted system on classifying lower third molars

Objectives: The present study evaluates the reliability of the Radio Memory® software (Radio Memory; Belo Horizonte,Brasil.) on classifying lower third molars, analyzing intra- and interexaminer agreement of the results. Study Design: An observational, descriptive study of 280 lower third molars was made. The corresponding orthopantomographs were analyzed by two examiners using the Radio Memory® software. The exam was repeated 30 days after the first observation by each examiner. Both intra- and interexaminer agreement were determined using the SPSS v 12.0 software package for Windows (SPSS; Chicago, USA). Results: Intra- and interexaminer agreement was shown for both the Pell & Gregory and the Winter classifications, p<0.01, with 99% significant correlation between variables in all the cases. Conclusions: The use of Radio Memory® software for the classification of lower third molars is shown to be a valid alternative to the conventional method (direct evaluation on the orthopantomograph), for both clinical and investigational applications.

Occlusal and dentofacial characteristics of the deciduous dentition and treatment effects of the eruption guidance appliance in the early mixed dentition

The aim of this investigation was to analyze the dental occlusion in the deciduous dentition, and the effects of orthodontic treatment carried out in the early mixed dentition with the eruption guidance appliance. The deciduous occlusion and craniofacial morphology of 486 children (244 girls and 242 boys) were investigated at the onset of the mixed dentition period (mean age 5.1 years, range 4.0-7.8 years). Treatment in the treatment group and follow-up in the control group were started when the first deciduous incisor was exfoliated (T1) and ended when all permanent incisors and first molars were fully erupted (T2). The mean age of the children was 5.1 years (SD 0.5) at T1 and 8.4 years (SD 0.5) at T2. Treatment was carried out with the eruption guidance appliance. Occlusal changes that took place in 167 children were compared with those of 104 untreated control children. Pre- and post-treatment cephalometric radiographs were taken, and the craniofacial morphology of 115 consecutively treated children was compared with that of 104 control children. The prevalence of malocclusion in the deciduous dentition was 68% or 93% depending on how the cut-off value between the acceptable and non-acceptable occlusal characteristic was defined. The early dentofacial features of children with distal occlusion, large overjet and deepbite differed from those with normal occlusion. However, the skeletal pattern of these three malocclusions showed considerable similarity each being characterized by a retrusive mandible, small maxillo-mandibular difference, convex profile, retrusive lower incisors, and large interincisal angle. In the treatment group, overjet and overbite decreased significantly from T1 to T2. Following treatment, a tooth-to-tooth contact was found in 99% of the treated children but only in 24% of the controls. A Class I molar relationship was observed in 90% of the children in the treatment group, and in 48% in the control group. Good alignment of the incisors was observed in 98% of the treated children, whereas upper crowding was found in 32% and lower crowding in 47% of the controls. A significant difference between the groups was found in the mandibular length, midfacial length and maxillo-mandibular differential. The occlusal correction, brought about by the eruption guidance appliance, was achieved mainly through changes in the dentoalveolar region of the mandible. In addition, the appliance seemed to enhance the growth of the mandible. Treatment in the early mixed dentition using the eruption guidance appliance is an effective method to normalize occlusion and reduce further need of orthodontic treatment. Only few spontaneous corrective changes can be expected without active intervention.

Sensibility and taste alterations after impacted lower third molar extractions. A prospective cohort study

Objectives: To determine the incidence, severity and duration of lingual tactile and gustatory function impairments after lower third molar removal. Study Design: Prospective cohort study with intra-subject measures of 16 patients undergoing lower third molar extractions. Sensibility and gustatory functions were evaluated in each subject preoperatively, one week and one month after the extraction, using Semmes-Weinstein monofilaments and 5 different concentrations of NaCl, respectively. Additionally, all patients filled a questionnaire to assess subjective perceptions. Results: Although patients did not perceive any sensibility impairments, a statistically significant decrease was detected when Semmes-Weinstein monofilaments. This alteration was present at one week after the surgical procedure and fully recovered one month after the extraction. There were no variations regarding the gustatory function. Conclusions: Lower third molar removal under local anesthesia may cause light lingual sensibility impairment. Most of these alterations remain undetected to patients. These lingual nerve injuries are present one week after the extraction and recover one month after surgery. The taste seems to remain unaffected after these procedures.

Sharp mandibular bone irregularities after lower third molar extraction: Incidence, clinical features and risk factors

Objectives: The purpose of this study was to determine the incidence and clinical symptoms associated with sharp mandibular bone irregularities (SMBI) after lower third molar extraction and to identify possible risk factors for this complication. Study Design: A mixed study design was used. A retrospective cohort study of 1432 lower third molar extractions was done to determine the incidence of SMBI and a retrospective case-control study was done to determine potential demographic and etiologic factors by comparing those patients with postoperative SMBI with controls. Results: Twelve SMBI were found (0.84%). Age was the most important risk factor for this complication. The operated side and the presence of an associated radiolucent image were also significantly related to the development of mandibular bone irregularities. The depth of impaction of the tooth might also be an important factor since erupted or nearly erupted third molars were more frequent in the SMBI group. Conclusions: SMBI are a rare postoperative complication after lower third molar removal. Older patients having left side lower third molars removed are more likely to develop this problem. The treatment should be the removal of the irregularity when the patient is symptomatic

Periodontal Diseases in Tanzania

Tutkimuksen tavoitteena oli kuvata hampaiden kiinnityskudossairauksien esiintyvyyttä ja suuhygieniatottumuksia Tansaniassa. Viiden eri tutkimuksen avulla kartoitettiin suuhygieniatottumuksia, kiinnityskudosten tilaa, kiinnityskudossairauksien riskitekijöitä ja hoidon tarvetta (CPITN) sekä ienvetäymiä. Tutkimukset toteutettiin eri paikkakunnilla vuosien 1987 ja 2003 välillä. Tutkittavat valittiin satunnaisesti tai harkitusti; tutkittavien määrä vaihteli 201:stä 1764:ään. Aineistot kerättiin kysymyslomakkeilla ja kliinisten tutkimusten avulla. Kliinisesti mitattiin plakin, hammaskiven ja ienten verenvuodon määrä, ientaskujen syvyys, ienvetäymien laajuus ja puuttuvien hampaiden lukumäärä. Tutkimusvälineinä käytettiin peiliä, Williamsin ja WHO:n ientaskumittareita. Muoviharjaksista hammasharjaa ilmoitti käyttävänsä 51,5-97,8% tutkituista. Ns. harjaustikun käyttö vaihteli paljon: 0,9-32,0 %. Plakkia löydettiin 65-100 %:lla tutkituista. Hammaskiveä oli suurimmalla osalla tutkituista. Myös ienverenvuotoa löytyi valtaosalta (79-100%). Ienverenvuotoa oli enemmän miehillä kuin naisilla sekä alhaisemman koulutustason omaavilla. Neljäkymmentä vuotta täyttäneiltä löydettiin 4–5 mm:n syvyisiä ientaskuja 82,1 %:lta ja ≥ 6 mm:n taskuja 43,8 %:lta. Suun terveystottumusten ohjaamiseen oli tarvetta yli 90 %:lla, hammaskiven poistoon ja juurten pinnan tasoitukseen yli 80%:lla. Yleisimmät riskitekijät kiinnityskudossairauksille olivat ikä (≥ 35 vuotta), miessukupuoli, alhainen koulutustaso, plakin, hammaskiven ja ientulehduksen määrä sekä asuminen maaseudulla. Ienvetäymiä (≥ 4 mm) löytyi noin 54%:lla tutkituista. Ienvetäymiä oli useammin miehillä kuin naisilla ja ne olivat yhteydessä ikään sekä hammaskiven ja ienverenvuodon esiintymiseen. Suuhygieniataso tutkituilla henkilöillä oli huono ja ienvetäymien esiintyvyys korkea. Syviä ientaskuja löytyi kuitenkin harvoilta tutkituilta. Riskitekijät kiinnityskudossairauksille olivat ikä, miessukupuoli, alhainen koulutustaso, plakin, hammaskiven ja ientulehduksen määrä sekä asuminen maaseudulla. Ienvetäymien riskit olivat ikä, miessukupuoli, hammaskivi ja ienverenvuoto

Pregabalin in the treatment of inferior alveolar nerve paraesthesia following overfilling of endodontic sealer

A case of orofacial pain and inferior alveolar nerve (IAN) paraesthesia after extrusion of endodontic sealer within the mandibular canal treated with prednisone and pregabalin is described. A 36-year-old woman underwent root canal treatment of the mandibular second right premolar tooth. Post-operative panoramic radiograph revealed the presence of radiopaque canal sealer in the mandibular canal. Damage to IAN consecutive to extrusion of endodontic sealer was diagnosed. Non-surgical management was decided, including: 1 mg/kg/day prednisone 2 times/day, once-daily regimen, and 150 mg/day pregabalin, two doses per day, monitoring the progress with periodic follow-up visits. Six weeks after the incident the signs and symptoms were gone. The complete resolution of paraesthesia and the control of pain achieved suggest that a non-surgical approach, combining prednisone and the GABA analogue pregabalin, is a good option in the management of the IAN damage subsequent to endodontic sealer extrusion

Rigid Rod Polymer Fillers in Acrylic Denture and Dental Adhesive Resin Systems

Polymeric materials have been used in dental applications for decades. Adhesion of polymeric materials to each other and to the tooth substrate is essential to their successful use. The aim of this series of studies was two-folded. First, to improve adhesion of poly(paraphenylene) based rigid rod polymer (RRP) to other dental polymers, and secondly, to evaluate the usability of a new dentin primer system based on RRP fillers. Poly(paraphenylene) based RRP would be a tempting material for dental applications because of its good mechanical properties. To be used in dental applications, reliable adhesion between RRP and other dental polymers is required. In this series of studies, the adhesion of RRP to denture base polymer and the mechanical properties of RRP-denture base polymer-material combination were evaluated. Also adhesion of BisGMA-TEGDMA-resin to RRP was determined. Different surface treatments were tested to improve the adhesion of BisGMA-TEGDMA-resin to RRP. Results were based on three-point bending testing, Vickers surface hardness test and scanning electron microscope analysis (SEM), which showed that no reliable adhesion between RRP and denture base polymer was formed. Addition of RRP filler to denture base polymer increased surface hardness and flexural modulus but flexural strength decreased. Results from the shear bond strength test and SEM revealed that adhesion between resin and RRP was possible to improve by surface treatment with dichloromethane (DCM) based primer and a new kind of adhesive surface can be designed. The current dentin bonding agents have good immediate bond strength, but in long term the bond strength may decrease due to the detrimental effect of water and perhaps by matrix metalloproteinases. This leads to problems in longevity of restorations. Current bonding agents use organic monomers. In this series of studies, RRP filled dentin primer was tested in order to decrease the water sorption of the monomer system of the primers. The properties of new dentin primer system were evaluated in vitro by comparing it to commercial etch and rinse adhesive system. The results from the contact angle measurements and SEM showed that experimental primer with RRP reinforcement provided similar resin infiltration to dentin collagen and formed the resin-dentin interface as the control primer. Microtensile bond strength test and SEM revealed that in short term water storing, RRP increased bond strength and primer with BMEP-monomer (bis[2-(methacryloyloxy)-ethyl]phosphate) and high solvent concentration provided comparable bonding properties to the commercial control primers. In long term water storing, the high solvent-monomer concentration of the experimental primers decreased bond strength. However, in low solvent-monomer concentration groups, the long-term water storing did not decrease the bond strength despite the existence of hydrophilic monomers which were used in the system. These studies demonstrated that new dentin primer system reached the mechanical properties of current traditional etch and rinse adhesive system in short time water storing. Improved properties can be achieved by further modifications of the monomer system. Studies of the adhesion of RRP to other polymers suggest that adhesion between RRP and other dental polymers is possible to obtain by certain surface treatments.

Hammashihnajohdeakseleiden liikkeiden synkronointi

Nykyisessä valmistusteollisuudessa erilaisten robottien ja automatisoitujen tuotantovaiheiden rooli on erittäin merkittävä. Tarkasti suunnitellut liikkeet ja toimintavaiheet voidaan nykyisillä järjestelmillä ajoittaa tarkasti toisiinsa nähden, jolloin erilaisten virhetilanteidenkin sattuessa järjestelmä pystyy toimimaan tilanteen edellyttämällä tavalla. Automatisoinnin etuna on myös tuotannon muokkaaminen erilaisten tuotteiden valmistamiseen pienillä muutoksilla, jolloin tuotantokustannukset pysyvät matalina myös pienten valmistuserien tapauksissa. Usean akselin laitteissa eli niin sanotuissa moniakselikäytöissä laitteen toimintatarkkuus riippuu jokaisen liikeakselin tarkkuudesta. Liikkeenohjauksessa on perinteisesti ollut käytössä myötäkytketty paikkakaskadi, jonka virityksessä otetaan huomioon akselilla olevat erilaiset dynaamiset tilat ja käytettävät referenssit. Monissa nykyisissä hajautetuissa järjestelmissä eli moniakselikäytöissä, joissa jokaiselle akselille on oma ohjauslaite, ei yksittäisen akselin paikkavirhettä huomioida muiden akseleiden ohjauksessa. Työssä tutkitaan erilaisia moniakselijärjestelmien ohjausmenetelmiä ja myötäkytketyn paikkakaskadin toimintaa moniakselikäytössä pyritään parantamaan tuomalla paikkasäätimen rinnalle toinen säädin, jonka tulona on akseleiden välinen paikkaero.

"Cara inchada" of cattle, an infectious, apparently soil antibiotics-dependant periodontitis in Brazil

The objective of this review on the investigation of "cara inchada" in cattle (CI), pursued over the last 30 years, was to elucidate the pathogenicity of the disease and come to proper conclusions on its etiology. CI has been widely considered to be of nutritional origin, caused primarily by mineral deficiency or imbalance. However, the disease consists of a rapidly progressive periodontitis, affecting the periodontal tissues at the level of the premolars and molars during the period of tooth eruption generally starting in young calves. The disease led to great economic losses for farmers in central-western Brazil, after the occupation of new land for cattle raising in the 1960s and 1970s. The lateral enlargement of the maxillary bones of affected calves gave the disease the popular name of "cara inchada", i.e., swollen or enlarged face. The enlargement was found to be due to a chronic ossifying periostitis resulting from the purulent alveolitis of CI. Black-pigmented non-saccharolytic Bacteroides melaninogenicus, always together with Actinomyces (Corynebacterium) pyogenes, were isolated in large numbers from the periodontal lesions. B. melaninogenicus could be isolated in small numbers also from the marginal gingiva of a few healthy calves maintained on CI-free farms. "In vitro"-assays showed that streptomycin and actinomycin, as well as the supernatants of cultivates of actinomycetes from soils of CI-prone farms, applied in subinhibitory concentrations to the bacteria tested, enhanced significantly (up to 10 times) the adherence of the black-pigmented B.melaninogenicus to epithelial cells of the bovine gingiva. The antibiotics are apparently produced in large quantities by the increased number of soil actinomycetes, including the genus Streptomyces, that develop when soil microflora are modified by cultivating virgin forest or "Cerrado" (tree-savanna) for the first time for cattle grazing. The epidemiology of CI now provides strong evidence that the ingestion with the forage of such antibiotics could possibly be an important determinant factor for the onset and development of this infectious periodontitis. The antibiotic enhanced adherence of B.melaninogenicus to the sulcus-epithelium of the marginal gingiva, is thought to allow it to colonize, form a plaque and become pathogenic. There is experimental evidence that this determinant factor for the development of the periodontitis is present also in the milk of the mothers of CI-diseased calves. It has been shown that the bacteria isolated from the periodontal CI-lesions produce enzymes and endotoxins capable of destroying the periodontal tissues. The epidemiology of CI, with its decline in incidence and its disappearance after several years, could be explained by the fact that the former equilibrium of the microflora of the once undisturbed virgin soil has been reached again and that the number of antibiotic producing actinomycetes has been anew reduced. By this reasoning and all the data available, CI should be considered as a multifactorial infectious disease, caused primarily by the anaerobic black-pigmented non-saccharolytic Bacteroides melaninogenicus, always together with the micro-anaerobic Actinomyces pyogenes. Accordingly, the onset and development of the infectious periodontitis is apparently determined by ingestion with the forage of subinhibitory concentrations of antibiotics produced in recently cultivated virgin soils. This hypothesis is supported by the recent observation of renewed outbreaks of CI-periodontitis in former CI-prone areas, following fresh cultivation after many years. The infectious nature of CI is confirmed by trials in which virginiamycin was used efficiently for the oral treatment of CI-diseased cattle. Previously it has been shown, that spiramycin and virginiamycin, used as additives in mineral supplements, prevented CI-periodontitis.

Anatomical and histological characteristics of teeth in agouti (Dasyprocta prymnolopha Wagler, 1831)

The agouti species Dasyprocta prymnolopha (D. prymnolopha) is a medium-sized rodent, diurnal, and characteristic of northeastern Brazil, south of the Amazon. Several studies have been made on these rodents. However, there is a lack of analysis of masticatory system, in particular morphology of the teeth. Thus, this research seeks to describe anatomical and histological aspects of the agouti teeth. For this purpose, we used adult agouti, in which measurements and descriptions of teeth and dental tissues were made. It was observed that the dental arch of D. prymnolopha comprises of twenty teeth, evenly distributed in the upper and lower arch, being inferior teeth larger than their corresponding higher. The incisors are larger, and between the posterior premolars and molars, there is a gradual increase in length in the anterior-posterior arch. In microscopic examination, a prismatic appearance was observed consisting of enamel prisms arranged in different directions, behind the enamel and dentin with standard tubular dentinal tubules with variable diameter and far between, also showing a sinuous path from the inner portion to the junction with more superficial enamel. Morphological analysis of dental tissues showed that an enamel with structural organization adapted to the act of chewing and high impact dentin compatible with standard tubular function resilience and mechanical damping of masticatory forces, as found in larger animals, confirming the understanding of eating habits that define much of its ecological functions within the ecosystem they inhabit.

Evaluation of a model for induction of periodontal disease in dogs

There are several methods for inducing periodontal disease in animal models, being the bone defect one of the most reported. This study aimed to evaluate this model, through clinical, radiographic, tomographic and histological analyzes, thus providing standardized data for future regenerative works. Twelve dogs were subjected to the induction protocol. In a first surgical procedure, a mucoperiosteal flap was made on the buccal aspect of the right third and fourth premolars and a defect was produced exposing the furcation and mesial and distal roots, with dimensions: 5mm coronoapical, 5mm mesiodistal, and 3mm buccolingual. Periodontal ligament and cementum were curetted and the defect was filled with molding polyester, which was removed after 21 days on new surgical procedure. Clinical and radiographic examinations were performed after the two surgeries and before the collection of parts for dental tomography and histological analysis. All animals showed grade II furcation exposure in both teeth. Clinical attachment level increased after induction. Defect size did not change for coronoapical and buccolingual measurements, while mesiodistal size was significantly higher than at the time of defect production. Radiographic analysis showed decreased radiopacity and discontinuity of lamina dura in every tooth in the furcation area. The horizontal progression of the disease was evident in micro-computed tomography and defect content in the histological analysis. Therefore, it is concluded that this method promotes the induction of periodontal disease in dogs in a standardized way, thus being a good model for future work.

Influence of Cutting Conditions on Tool Life, Tool Wear and Surface Finish in the Face Milling Process

The main goal of this work is to study the influence of cutting conditions - cutting speed, feed velocity and feed per tooth - on tool life and surface finish of the workpiece in the face milling of flat surfaces. Aiming to achieve this goal, several milling experiments were carried out with different cutting speeds, feed velocities and feeds per tooth. In the first phase of the experiments, cutting speed was varied without varying feed velocity, which caused a variation in feed per tooth. In the second phase of the experiments, cutting speed and feed velocity were varied in such a way that feed per tooth was kept constant. Tool flank wear and surface roughness of the workpiece were measured as cutting time elapsed. The main conclusions of this work are that a) cutting speed has a strong influence on tool life, regardless of whether feed velocity or feed per tooth varies and b) an increase in surface roughness of the workpiece is not closely related to an increase in wear of the primary cutting edge.

Wind Turbine Direct-Drive Permanent-Magnet Generator with Direct Liquid Cooling for Mass Reduction

Today’s electrical machine technology allows increasing the wind turbine output power by an order of magnitude from the technology that existed only ten years ago. However, it is sometimes argued that high-power direct-drive wind turbine generators will prove to be of limited practical importance because of their relatively large size and weight. The limited space for the generator in a wind turbine application together with the growing use of wind energy pose a challenge for the design engineers who are trying to increase torque without making the generator larger. When it comes to high torque density, the limiting factor in every electrical machine is heat, and if the electrical machine parts exceed their maximum allowable continuous operating temperature, even for a short time, they can suffer permanent damage. Therefore, highly efficient thermal design or cooling methods is needed. One of the promising solutions to enhance heat transfer performances of high-power, low-speed electrical machines is the direct cooling of the windings. This doctoral dissertation proposes a rotor-surface-magnet synchronous generator with a fractional slot nonoverlapping stator winding made of hollow conductors, through which liquid coolant can be passed directly during the application of current in order to increase the convective heat transfer capabilities and reduce the generator mass. This doctoral dissertation focuses on the electromagnetic design of a liquid-cooled direct-drive permanent-magnet synchronous generator (LC DD-PMSG) for a directdrive wind turbine application. The analytical calculation of the magnetic field distribution is carried out with the ambition of fast and accurate predicting of the main dimensions of the machine and especially the thickness of the permanent magnets; the generator electromagnetic parameters as well as the design optimization. The focus is on the generator design with a fractional slot non-overlapping winding placed into open stator slots. This is an a priori selection to guarantee easy manufacturing of the LC winding. A thermal analysis of the LC DD-PMSG based on a lumped parameter thermal model takes place with the ambition of evaluating the generator thermal performance. The thermal model was adapted to take into account the uneven copper loss distribution resulting from the skin effect as well as the effect of temperature on the copper winding resistance and the thermophysical properties of the coolant. The developed lumpedparameter thermal model and the analytical calculation of the magnetic field distribution can both be integrated with the presented algorithm to optimize an LC DD-PMSG design. Based on an instrumented small prototype with liquid-cooled tooth-coils, the following targets have been achieved: experimental determination of the performance of the direct liquid cooling of the stator winding and validating the temperatures predicted by an analytical thermal model; proving the feasibility of manufacturing the liquid-cooled tooth-coil winding; moreover, demonstration of the objectives of the project to potential customers.

The position of the hyaline papilla and the genus concept of Cheilolejeunea (Spruce) Schiffn. (Lejeuneaceae)

In this paper, the genus concept of Cheilolejeunea is discussed and revalued based upon the concept of the real position of the hyaline papilla, as well as upon the definition of apical tooth of the lobule in the genus.