Effect of forest-based biofuels production on carbon footprint, Case: Integrated LWC paper mill

International energy and climate strategies also set Finland’s commitments to increasing the use of renewable energy sources and reducing greenhouse gas emissions. The target can be achieved by, for example, increasing the use of energy wood. Finland’s forest biomass potential is significant compared with current use. Increased use will change forest management and wood harvesting methods however. The thesis examined the potential for integrated pulp and paper mills to increase bioenergy production. The effects of two bioenergy production technologies on the carbon footprint of an integrated LWC mill were studied at mill level and from the cradle-to-customer approach. The LignoBoost process and FT diesel production were chosen as bioenergy cases. The data for the LignoBoost process were obtained from Metso and for the FT diesel process from Neste Oil. The rest of the information is based on the literature and databases of the KCL-ECO life-cycle computer program and Ecoinvent. In both case studies, the carbon footprint was reduced. From the results, it can be concluded that it is possible to achieve a fossil-fuel-free pulp mill with the LignoBoost process. By using steam from the FT diesel process, the amount of auxiliary fuel can be reduced considerably and the bark boiler can be replaced. With a choice of auxiliary fuels for use in heat production in the paper mill and the production methods for purchased electricity, it is possible to affect the carbon footprints even more in both cases.

Simulating the performance of paper machine control

The topic of this thesis is the simulation of a combination of several control and data assimilation methods, meant to be used for controlling the quality of paper in a paper machine. Paper making is a very complex process and the information obtained from the web is sparse. A paper web scanner can only measure a zig zag path on the web. An assimilation method is needed to process estimates for Machine Direction (MD) and Cross Direction (CD) profiles of the web. Quality control is based on these measurements. There is an increasing need for intelligent methods to assist in data assimilation. The target of this thesis is to study how such intelligent assimilation methods are affecting paper web quality. This work is based on a paper web simulator, which has been developed in the TEKES funded MASI NoTes project. The simulator is a valuable tool in comparing different assimilation methods. The thesis contains the comparison of four different assimilation methods. These data assimilation methods are a first order Bayesian model estimator, an ARMA model based on a higher order Bayesian estimator, a Fourier transform based Kalman filter estimator and a simple block estimator. The last one can be considered to be close to current operational methods. From these methods Bayesian, ARMA and Kalman all seem to have advantages over the commercial one. The Kalman and ARMA estimators seems to be best in overall performance.

Permanent Magnet Synchronous Machine for Parallel Hybrid Vehicle

The aim of this thesis is to describe hybrid drive design problems, the advantages and difficulties related to the drive. A review of possible hybrid constructions, benefits of parallel, series and series-parallel hybrids is done. In the thesis analytical and finite element calculations of permanent magnet synchronous machines with embedded magnets were done. The finite element calculations were done using Cedrat’s Flux 2D software. This machine is planned to be used as a motor-generator in a low power parallel hybrid vehicle. The boundary conditions for the design were found from Lucas-TVS Ltd., India. Design Requirements, briefly: • The system DC voltage level is 120 V, which implies Uphase = 49 V (RMS) in a three phase system. • The power output of 10 kW at base speed 1500 rpm (Torque of 65 Nm) is desired. • The maximum outer diameter should not be more than 250 mm, and the maximum core length should not exceed 40 mm. The main difficulties which the author met were the dimensional restrictions. After having designed and analyzed several possible constructions they were compared and the final design selected. Dimensioned and detailed design is performed. Effects of different parameters, such as the number of poles, number of turns and magnetic geometry are discussed. The best modification offers considerable reduction of volume.

Design and analysis of a transversal-flux switched-reluctance-linear-machine pole-pair

The Switched Reluctance technology is probably best suited for industrial low-speed or zerospeed applications where the power can be small but the torque or the force in linear movement cases might be relatively high. Because of its simple structure the SR-motor is an interesting alternative for low power applications where pneumatic or hydraulic linear drives are to be avoided. This study analyses the basic parts of an LSR-motor which are the two mover poles and one stator pole and which form the “basic pole pair” in linear-movement transversal-flux switchedreluctance motors. The static properties of the basic pole pair are modelled and the basic design rules are derived. The models developed are validated with experiments. A one-sided one-polepair transversal-flux switched-reluctance-linear-motor prototype is demonstrated and its static properties are measured. The modelling of the static properties is performed with FEM-calculations. Two-dimensional models are accurate enough to model the static key features for the basic dimensioning of LSRmotors. Three-dimensional models must be used in order to get the most accurate calculation results of the static traction force production. The developed dimensioning and modelling methods, which could be systematically validated by laboratory measurements, are the most significant contributions of this thesis.

Automated, adaptive methods for forest inventory

Forest inventories are used to estimate forest characteristics and the condition of forest for many different applications: operational tree logging for forest industry, forest health state estimation, carbon balance estimation, land-cover and land use analysis in order to avoid forest degradation etc. Recent inventory methods are strongly based on remote sensing data combined with field sample measurements, which are used to define estimates covering the whole area of interest. Remote sensing data from satellites, aerial photographs or aerial laser scannings are used, depending on the scale of inventory. To be applicable in operational use, forest inventory methods need to be easily adjusted to local conditions of the study area at hand. All the data handling and parameter tuning should be objective and automated as much as possible. The methods also need to be robust when applied to different forest types. Since there generally are no extensive direct physical models connecting the remote sensing data from different sources to the forest parameters that are estimated, mathematical estimation models are of "black-box" type, connecting the independent auxiliary data to dependent response data with linear or nonlinear arbitrary models. To avoid redundant complexity and over-fitting of the model, which is based on up to hundreds of possibly collinear variables extracted from the auxiliary data, variable selection is needed. To connect the auxiliary data to the inventory parameters that are estimated, field work must be performed. In larger study areas with dense forests, field work is expensive, and should therefore be minimized. To get cost-efficient inventories, field work could partly be replaced with information from formerly measured sites, databases. The work in this thesis is devoted to the development of automated, adaptive computation methods for aerial forest inventory. The mathematical model parameter definition steps are automated, and the cost-efficiency is improved by setting up a procedure that utilizes databases in the estimation of new area characteristics.

Regeneration of five commercially-valuable tree species after experimental logging in an Amazonian forest

This study investigated the regeneration variation of five commercially valuable tree species in relation to different intensities of felling in fourteen 4-ha plots in an area under experimental forest management. This experiment was carried out in a typical Amazonian tropical forest sample on "terra-firme," in Manaus (AM). Plots were logged 7 and 8 years (1987 and 1988), or 3 years (1993) before the study. All trees with height greater than 2 m, and diameter at breast height (DBH) smaller than 10 cm were measured. Only Aniba hostmanniana, Ocotea aciphylla, Licaria pachycarpa, Eschweilera coriacea and Goupia glabra were sufficiently common for individual analyses. These species have high timber values in the local market. Eight years after logging, the species responded differently to logging intensities. The numbers of individuals of Goupia glabra and Aniba hostmanniana were positively related to the intensity of logging, while Ocotea aciphylla, Licaria pachycarpa, and Eschweilera coriacea showed no statistically significant response. In the most recently (1993) logged areas, Goupia glabra and Aniba hostmanniana had higher numbers of individuals than the control plots.

Harvesting and wood transport planning with SNAP III program (Scheduling and Network Analysis Program) in a pine plantation in Southeast Brazil

The objective of this study was to verify the potential of SNAP III (Scheduling and Network Analysis Program) as a support tool for harvesting and wood transport planning in Brazil harvesting subsystem definition and establishment of a compatible route were assessed. Initially, machine operational and production costs were determined in seven subsystems for the study area, and quality indexes, construction and maintenance costs of forest roads were obtained and used as SNAP III program input data. The results showed, that three categories of forest road occurrence were observed in the study area: main, secondary and tertiary which, based on quality index, allowed a medium vehicle speed of about 41, 30 and 24 km/hours and a construction cost of about US$ 5,084.30, US$ 2,275.28 and US$ 1,650.00/km, respectively. The SNAP III program used as a support tool for the planning, was found to have a high potential tool in the harvesting and wood transport planning. The program was capable of defining efficiently, the harvesting subsystem on technical and economical basis, the best wood transport route and the forest road to be used in each period of the horizon planning.

Chlorophyll fluorescence of tropical tree species in a semi-deciduous forest gap

The characterization of different ecological groups in a forest formation/succession is unclear. To better define the different successional classes, we have to consider ecophysiological aspects, such as the capacity to use or dissipate the light energy available. The main objective of this work was to assess the chlorophyll fluorescence emission of tropical tree species growing in a gap of a semi-deciduous forest. Three species of different ecological groups were selected: Croton floribundus Spreng. (pioneer, P), Astronium graveolens Jacq. (early secondary, Si), and Esenbeckia febrifuga A. Juss. (late secondary, St). The potential (Fv/Fm) and effective (deltaF/Fm') quantum efficiency of photosystem II, apparent electron transport rate (ETR), non-photochemical (qN) and photochemical (qP) quenching of fluorescence were evaluated, using a modulated fluorometer, between 7:30 and 11:00 h. Values of Fv/Fm remained constant in St, decreasing in P and Si after 9:30 h, indicating the occurrence of photoinhibition. Concerning the measurements taken under light conditions (deltaF/Fm', ETR, qP and qN), P and Si showed better photochemical performance, i.e., values of deltaF/Fm', ETR and qP were higher than St when light intensity was increased. Values of qN indicated that P and Si had an increasing tendency of dissipating the excess of energy absorbed by the leaf, whereas the opposite was found for St. The principal component analysis (PCA), considering all evaluated parameters, showed a clear distinction between St, P and Si, with P and Si being closer. The PCA results suggest that chlorophyll fluorescence may be a potential tool to differentiate tree species from distinct successional groups.

Wood consumption rates of forest species by subterranean termites (Isoptera) under field conditions

Termites are well -known for their capacity to damage and destroy wood and wood products of all kinds in the tropics and subtropics. A field test was undertaken to evaluate variations in wood consumption of Pinus sp. and three species of Eucalyptus by subterranean termites. The test consisted of wooden stakes of each species being initially submitted to water immersion for 0, 24, 48 and 72 h, and buried in the ground to natural infestation by subterranean termites for an exposure period of 30, 45 and 60 days. Three species of subterranean termites were identified: Heterotermes longiceps (Snyder), Coptotermes gestroi (Wasmann) (Isoptera: Rhinotermitidae), and Nasutitermes jaraguae (Holmgren) (Isoptera: Termitidae). This is the first record of occurrence of H. longiceps in the state of Rio de Janeiro. Although the wood-consumption rates were not correlated significantly with their wood densities, there was a tendency of the softwoods (E. robusta and Pinus sp.) to be more consumed by subterranean termites than the woods of intermediate hardness (E. pellita and E. urophylla). Among the eucalyptus, E. robusta showed to be more susceptible to attack by subterranean termites than E. pellita and E. urophylla

Characterization of Acromyrmex subterraneus brunneus (Hymenoptera: Formicidae) young nests in a fragment of the Neotropical Forest

Young nests of Acromyrmex subterraneus brunneus are characterized by refuse soil in the exterior of the nest, a single fungus chamber 11 to 20 cm deep in relation to soil surface and internal volume ranging from 0.3 to 1.5 liters. These nidification patterns are important characteristics for identifying and understanding the interactions between species and their habitats.

Industrial solid waste (whitewash mud) use in forest road pavements

The objective of the present study was to evaluate the effects of industrial solid waste (whitewash mud) on geotechnical properties considering the following engineering parameters: California Bearing Ratio (CBR), Atterberg limits and Permeability test. Seven soil samples derived from Alagoinhas, Bahia - Brazil, were classified by the Transportation Research Board (TRB) system. Two were selected as having a great geotecnical potential classified as A-3 (0) and A-2-4 (0), whitewash mud contents 10%, 15%, 20% and 25% dry weight and medium compaction effort were studied in the laboratory testing program. The results indicated the soil denominated good gravel as being the most promising one, when stabilized with whitewash mud, reaching the best results with the dosage of 20 and 25% of whitewash mud.

A comparative study of four tree species used in riparian forest restoration along Uruguay River, Brazil

Silvicultural and ecological knowledge about tree species is basic to restoration planning, particularly in high diversity regions. Here we present a comparison of four native tree species from the middle Uruguay River basin, Brazil-Argentine frontier: Heliocarpus americanus L. (Malvaceae), Maclura tinctoria (L.) D. Don ex Steud. (Moraceae), Schinus terebinthifolius Raddi (Anacardiaceae) and Cordia trichotoma (Vell.) Arrab. ex Steud. (Boraginaceae). We obtained data on initial growth, light interception, litterfall and litter mineral contents. H. americanus presented the greatest height and the lowest value of height/crown width ratio. H. americanus and M. tinctoria presented the highest light interception rate (>94 %) and highest litterfall (879 ± 151 and 792 ± 164 g·m-2·year-1, respectively). For the set of species, the lowest litterfall occurred between July and September. H. americanus presented the highest K concentration (1.13%) in the litter, while C. trichotoma had the highest values of Ca and Mg (6.35 and 2.02 %, respectively). S. terebinthifolius had the lowest light interception rate and litter mineral content.