The determination of ethylene-propylene copolymer-grafted-glycidyl methacrylate by the contact angle method

The contact angles theta of some liquids on ethylene-propylene copolymer-grafted-glycidyl methacrylate (EPM-g-GMA) were measured. The critical surface tensions r(c) of EPM-g-GMA were evaluated by the Zisman Plot (cos theta versus r(L)), Young-Dupre-Good-Girifalco plot (1 + cos theta versus 1/r(L)(0.5)) and log (1 + cos theta) versus log(r(L)) plot. The following results were obtained: the r(c) values varied significantly with the estimation methods. The critical surface tension r(c) decreased with the increase of the degree of grafting of EPM-g-GMA.

Small angle X-ray scattering study of structural parameters of the aggregated state in polyamide 1010+BMI

The structural parameters of the aggregated state in the polyamide PA1010 and N,N'-bismaleimide-4,4'-diphenyl methane (BMI) system were computed by means of the desmearing intensity from SAXS and using the concept of the distance distribution function. The results revealed that the parameters Q, I(0), l(c) and L decreased with the increase BMI component, whereas O-s increased. The particle dimension Z for different BMI contents was less than 13.2 nm, and the maximum value of the distance distribution function P(Z) was found to be in the range Z = 6.5-7.0 nm.

SMALL-ANGLE X-RAY-SCATTERING STUDY ON THE INTERFACE IN BLOCK-COPOLYMERS WITH FRACTAL PROPERTIES

The interface thickness in two triblock copolymers were determined using small-angle x-ray scattering in the context of the theory proposed by Ruland. The thickness was found to be nonexistent for the samples at three different temperatures. By viewing th

Differences in the rDNA-bearing chromosome divide the Asian-Pacific and Atlantic species of Crassostrea (Bivalvia, Mollusca)

Karyotype and chromosomal location of the major ribosomal RNA genes (rDNA) were studied using fluorescence in situ hybridization (FISH) in five species of Crassostrea: three Asian-Pacific species (C. gigas, C. plicatula, and C. ariakensis) and two Atlantic species (C. virginica and C. rhizophorae). FISH probes were made by PCR amplification of the intergenic transcribed spacer between the 18S and 5.8S rRNA genes, and labeled with digoxigenin-11-dUTP. All five species had a haploid number of 10 chromosomes. The Atlantic species had 1-2 submetacentric chromosomes, while the three Pacific species had none. FISH with metaphase chromosomes detected a single telomeric locus for rDNA in all five species without any variation. In all three Pacific species, rDNA was located on the long arm of Chromosome 10 (10q)-the smallest chromosome. In the two Atlantic species, rDNA was located on the short arm of Chromosome 2 (2p)-the second longest chromosome. A review of other studies reveals the same distribution of NOR sites (putative rDNA loci) in three other species: on 10q in C. sikamea and C. angulata from the Pacific Ocean and on 2p in C. gasar from the western Atlantic. All data support the conclusion that differences in size and shape of the rDNA-bearing chromosome represent a major divide between Asian-Pacific and Atlantic species of Crassostrea. This finding suggests that chromosomal divergence can occur under seemingly conserved karyotypes and may play a role in reproductive isolation and speciation.

Talc-bearing serpentinized peridotites from the southern Mariana forearc: implications for aseismic character within subduction zones

The serpentinized peridotites overlying the subducted zones in the Izu-Bonin-Mariana (IBM) arc system have been interpret as the cause of the low-velocity layer identified beneath the IBM froearc, in turn few earthquakes occurred along the plate boundary. Chrysotile, which is a low temperature and highly hydrated phase of serpentine with low frictional strength, has been suggested as the low velocity material in the serpentinized peridotites, besides, brucite is inferred to be likely conducive to stable sliding. However, such idea encounters challenging in our serpentinized peridotites from the southern Mariana forearc, which absent both the above minerals. The presence of talc, which characterized by its weak, low-friction and inherently stable sliding behavior, provides new clue. Here we report the occurrence of talc in serpentinized peridotites collected from the landward trench slope of the southern Mariana forearc. We infer that talc is mainly forming as a result of the reaction of serpentine minerals with silica-saturated fluids released from the subducting slab, and talc also occurs as talc veins sometimes. Due to its unique physical properties, talc may therefore play a significant role in aseismic slip in the IBM subduction zone.

Isotopic feature and uranium dating of the volcanic rocks in the Okinawa Trough

Volcanic rocks from the northern and middle Okinawa Trough were dated by uranium-series dating method. Differential fractions using magnetic procedure were designed to separate samples. New report on the ages and isotopic data of rocks in the northern trough (especially black pumice) was discussed. Based on the uranium dates and Sr-Nd isotopic ratio, magmatic evolution process of the Okinawa Trough was noted. Firstly, there have been wide silicic volcanic activities in the Okinawa Trough from late Pleistocene to present, and the volcanic rocks can be divided into three subgroups. Secondly, magma generally came from PREMA source area under the Okinawa Trough. Magmatic evolution in the northern trough was similar to the middle, but different to the south. Finally, volcanic activities indicated that opening of the southern Okinawa Trough did not happen due to the collision between Luson Arc and Eurasian Plate until the early Pleistocene.

Studies on the regional feature of organic carbon in sediments off the Huanghe River Estuary waters

Organic carbon (OC) in definitely small area sediments(according to marine dimension)off the Huanghe River Estuary is investigated in order to evaluate the feature of regional difference of physical and chemical properties in marginal sea sediments. The distributions of OC in sediments with natural grain size and the relationship with the pH, Eh,Es and Fe3+/Fe2+ are discussed. In addition,OC decomposition rates in surfacial/subsurfacial sediments are estimated. OC concentrations range from 0.26% to 1.8%(wt)in the study area. Significant differences in OC content and in horizontal distribution as well as various trends in surfacial/subsurfacial sediments exhibit the feature of regional difference remarkably in marginal sea sediments. The complicated distribution of OC in surface sediments is due to the influence of bacterial activity and abundance, bioturbation of benthos and physical disturbance. The OC decomposition rate constant in surfacial/subsurfacial sediments ranges from 0.0097 to 0.076 a(-1) and the relatively high values may be mainly related to bacteria that are mainly responsible for OC mineralization;meio-and macrofauna affect OC degradation both directly, through feeding on it, and indirectly through bioturbation and at the same time coarse sediments are also disadvantageous to OC preservation. In almost all the middle and bottom sediments the contents of OC decrease with the increase of deposition depth, which indicates that mineralization of OC in the middle and bottom sediments has occurred via processes like SO42- reduction and Fe-oxide reduction.

Aminic nitrogen-bearing polydentate Schiff base compounds as corrosion inhibitors for iron in acidic media: A quantum chemical calculation

Quantum chemical calculations based on DFT method were performed on three polydentate Schiff base compounds (PSCs) used as corrosion inhibitors for iron in acid media to determine the relationship between the molecular structure of PSC and inhibition efficiency. The structural parameters, such as the frontier molecular orbital energy HOMO (highest occupied molecular orbital) and LUMO (lowest unoccupied molecular orbital), the charge distribution of the studied inhibitors, the absolute electronegativity (chi) values, and the fraction of electrons (Delta N) transfer from inhibitors to iron, were also calculated and correlated with inhibition efficiencies. The results showed that the inhibition efficiency of PSCs increased with the increase in E-HOMO and decrease in E-LUMO-E-HOMO; and the areas containing N atoms are most possible sites for bonding the metal iron surface by donating electrons to the metal. (C) 2007 Elsevier Ltd. All rights reserved.

海拉尔盆地贝尔凹陷基岩潜山特征及储层预测

The lithology of the buried hill of Triassic Budate group in Beier depression is epimetamorphic clastic rock and volcanic clastic rock stratum. Recently the favorable hydrocarbon show was discovered in buried hill of base rock, and large-duty industrial oil stream was obtained in some wells in Beier depression. Based on the information of seismos and wells, the tectonic framework, tectonic deformation times and faulted system of the Beier depression are comprehensively studied, then configuration, evolutional history, genetic type and distributed regularity of buried hill are defined. According to observing description and analysis of core sample, well logging and interpretive result of FMI, the lithological component, diagenetic type and diagenetic sequence of buried hill reservoir are confirmed, then reservoir space system of buried hill is distinguished, and vegetal feature, genetic mechanism and distributed regularity of buried hill fissure are researched, at the same time the quantitative relationship is build up between core fissures and fissures interpreted by FMI. After that fundamental supervisory action of fault is defined to the vegetal degree of fissure, and the fissure beneficial places are forecasted using fractal theory and approach. At last the beneficial areas of Budate group reservoir are forecasted by reservoir appraisal parameters optimization such as multivariate gradually regression analysis et. al. and reservoir comprehensive appraisal method such as weighing analyze and clustering procedure et. al. which can provide foundation for the next exploratory disposition. Such production and knowledge are obtained in this text as those: 1. Four structural layers and two faulting systems are developed, and four structural layers are carved up by three bed succession boundary surfaces which creates three tectonic distortional times homology. Three types of buried hill are divided, they are ancient physiognomy buried hill, epigenetic buried hill, and contemporaneous buried hill. 2. Reservoir space of Budate buried hill is mainly secondary pore space and fissure, which distributes near the unconformity and/or inside buried hill in sections. The buried hill reservoir experienced multi-type and multi-stage diagenetic reconstruction, which led to the original porosity disappeared, and multi secondary porosity was created by dissolution, superficial clastation and cataclasis et. al. in diagenetic stage, which including middle crystal pore, inter crystal pore, moldic pore, inter particle emposieu, corrosion pore space and fissure et. al. which improved distinctly reservoir capability of buried hill. 3. The inner reservoir of buried hill in Beier depression is not stratigraphic bedded construction, but is fissure developing place formed by inner fault and broken lithogenetic belt. The fissures in inner reservoir of buried hill are developed unequally with many fissure types, which mainly are high angle fissure and dictyonal fissures and its developing degree and distribution is chiefly controlled by faulting. 4. The results of reservoir comprehensive evaluate and reservoir predicting indicates that advantageous areas of reservoir of buried hill chiefly distributes in Sudeerte, Beixi and Huoduomoer, which comprehensive evaluate mainly Ⅱand Ⅲ type reservoir. The clues and results of this text have directive significance for understanding the hydrocarbon reservoir condition of buried hill in Beier depression, for studying hydrocarbon accumulated mechanism and distributed regularity, and for guiding oil and gas exploration. The results of this text also can enrich and improve nonmarine hydrocarbon accumulated theory.

鄂尔多斯盆地上古生界低渗透砂岩有效储层识别与预测

Sulige Gasfield, with a basically proven reserve as high as one trillion cubic meters, is one giant gas field discovered in China. The major gas -bearing layers are Upper Paleozoic strata with fluvial-lacustrine sedimentary facies. Generally, gas reservoirs in this field are characteristic by "five low" properties, namely low porosity, low permeability, low formation pressure, low productivity and low gas abundance. Reservoirs in this field also feature in a large distribution area, thin single sandbody thickness, poor reservoir physical properties, thin effective reservoir thickness, sharp horizontal and/or vertical changes in reservoir properties as well as poor connectivity between different reservoirs. Although outstanding achievements have been acquired in this field, there are still several problems in the evaluation and development of the reservoirs, such as: the relation between seismic attributes and reservoir property parameters is not exclusive, which yields more than one solution in using seismic attributes to predict reservoir parameters; the wave impedance distribution ranges of sandstone and mudstone are overlapped, means it is impossible to distinguish them through the application of post-stack impedance inversion; studies on seismic petrophysics, reservoir geophysical properties, wave reflection models and AVO features have a poor foundation, makes it difficult to recognize the specific differences between tight sandstone and gas-bearing sandstone and their distribution laws. These are the main reasons causing the low well drilling success rate and poor economic returns, which usually result in ineffective development and utilization of the field. Therefore, it is of great importance to perform studies on identification and prediction of effective reservoirs in low permeable sandstone strata. Taking the 2D and 3D multiwave-multicomponent seismic exploration block in Su6-Su5 area of Sulige field as a study area and He 8 member as target bed, analysis of the target bed sedimentary characteristics and logging data properties are performed, while criteria to identify effective reservoirs are determined. Then, techniques and technologies such as pre-stack seismic information (AVO, elastic impedance, wave-let absorption attenuation) and Gamma inversion, reservoir litological and geophysical properties prediction are used to increase the precision in identifying and predicting effective reservoirs; while P-wave and S-wave impedance, ratio of P/S wave velocities, rock elastic parameters and elastic impedance are used to perform sandstone gas-bearing property identification and gas reservoir thickness prediction. Innovative achievements are summarized as follows: 1. The study of this thesis is the first time that multiwave-multicomponent seismic data are used to identify and predict non-marine classic reservoirs in China. Through the application of multiwave-multicomponents seismic data and integration of both pre-stack and post-stack seismic data, a set of workflows and methods to perform high-precision prediction of effective reservoirs in low permeable sandstone is established systematically. 2. Four key techniques to perform effective reservoir prediction including AVO analysis, pre-stack elastic wave impedance inversion, elastic parameters inversion, and absorption attenuation analysis are developed, utilizing pre-stack seismic data to the utmost and increasing the correct rate for effective reservoir prediction to 83% from the former 67% with routine methods. 3. This thesis summarizes techniques and technologies used in the identification reservoir gas-bearing properties using multiwave-multicomponent seismic data. And for the first time, quantitative analysis on reservoir fluids such as oil, gas, and/or water are carried out, and characteristic lithology prediction techniques through the integration of pre-stack and post-stack seismic prediction techniques, common seismic inversion and rock elastic parameters inversion, as well as P-wave inversion and converted wave inversion is put forward, further increasing the correct rate of effective reservoir prediction in this area to 90%. 4. Ten seismic attribute parameters are selected in the 3D multi-wave area to perform a comprehensive evaluation on effective reservoirs using weighted-factor method. The results show that the first class effective reservoir covers an area of 10.08% of the study area, while the second and the third class reservoirs take 43.8% and 46% respectively, sharply increasing the success rate for appraisal and development wells.

东北亚构造-盆地演化及油气资源控制作用

The oil and gas potential of Northeast Asia is enormous, but the degree of exploration is very low in Northeast Asia (the degree is below 3%-10%).The reasons are as follows: First, it is relatively difficult to study the oil and gas bearing basins(OGB), which are of multiple types, in different tectonic settings, with complex geologic frameworks and with long-term geologic evolution. Secondly, because of the non-equilibrium in development of economy and regional market, application of theories and techniques and the research levels in different countries, the conclusions are not conformable, and even contradictory. Thirdly, most of the former researches were limited to one territory or one basin, and lack of systematical and in-depth study on geotectonic evolution, classification of basins, and the evaluation of hydrocarbon resources. In this thesis, integrated study of the regional tectonic feature and basin features of Northeast Asia was done, to understand the basin evolution history and the controlling action on oil and gas. Then, new conclusions are and exploration proposals are as following: 1. Geotectonic evolution in Northeast Asia: The main structural motion system in Paleozoic Era was longitudinal, and in Meso-cenozoic was latitudinal with the Pacific Ocean. The whole evolution history was just the one of pulling-apart, cutting-out, underthrusting and collision of the Central Asia- Mongolia Ocean and the Pacific Ocean. 2. The evolution characteristics of basins in Northeast Asia: mainly developed from longitudinal paste-up, collision and relaxation rifting motion in Paleozoic-Early Mesozoic Era and from underthrust, accretion, and receding of subducted zone of the Pacific Ocean in Late Mesozoic Era-Cenozoic Era. 3. The research in basin classification of Northeast Asia: According to geotectonic system, the basins can be classified into three types: intracratonic, pericratonic and active zone basin. And they can be further classified into 18 different types according to genetic mechanism and dynamic features. 4. The master control factors of oil and gas accumulation in Northeast Asia: high quality cap-rock for craton and pericrationic basin, the effective source rock and high quality cap-rock for Mesozoic rifted basins, intra-arc, fore-arc and back-arc basins. Graded exploration potential of oil and gas for basin in Northeast Asia according to 7 factor, hereby, divided the oil and gas potential of basins into 5 levels. 5. Evaluation of hydrocarbon resources: The difference of resource potential among these basins is huge in Northeast Asia. The evaluation of Mesozoic rifted basin and Pacific Ocean basin showed that the large scale rifted basin and retroarc basin(including backarc marginal sea basin) have great resource potential. 6. The writer believes that the next step should pay more attention to the evaluation of petroleum resource in Far East part of Russia and trace them. On the other hand, according to integrated analysis of oil/gas resource potential and the operation difficulty in this area, suggests that East-Siberia basin, East-Gobi-Tamchag basin, Sakhalin basin, North-Okhotck basin, West-Kamchatka basin could be as cooperation priority basins in future.

辽东湾隐蔽油气藏地球物理识别技术研究

In China and world, more than half the recent basin discovered reserves involve lithologic hydrocarbon reservoir reserves. The major target for further hydrocarbon basin exploration is the subtle reservoir. The Liaodong Bay prospect is much important in Bohai Sea, which includes Liaoxi low uplift, Liaodong uplift, Liaoxi sag and Liaozhong sag. After dozens years’ exploration in Liaodong Bay, few unexplored big-and-middle-sized favorable structural traps are remained and most of the stock structure targets are bad for fragmentary. Thus seeking for new prospect area and making a breakthrough, have become the unique way to relieve the severe exploration condition in Liaodong Bay. Technique Route Based on the petrophysical property of target area, the seismic forward inference of typical subtle trap model is expanded with analysis of logging, seismic and geologic data. According to petrophysical characteristics and forward inference and research on seismic response of actual seismic data in target area, the optimization of geophysical technique is used in subtle trap identification and the geophysical identification technique system of subtle reservoir is formed. The Key Research ① Petrophysical Model The petrophysical parameter is the basic parameter for seismic wave simulation. The seismic response difference of rocks bearing different fluids is required. With the crossplot of log data, the influence of petrophysical parameters on rock elastic properties of target area is analyzed, such as porosity, shale index, fluid property and saturation. Based on the current research on Biot-Gassmann and Kuster-Toksoz model, the petrophysical parameter calculator program which can be used for fluid substitution is established. ② S-wave evaluation based on conventional log data The shear velocity is needed during forward inference of AVO or other elastic wave field. But most of the recent conventional log data is lack of shear wave. Thus according to the research on petrophysical model, the rock S-wave parameter can be evaluated from conventional log data with probability inverse method. ③ AVO forward modeling based on well data For 6 wells in JZ31-6 block and 9 wells in LD22-1 block, the AVO forward modeling recording is made by log curve. The classification of AVO characteristics in objective interval is made by the lithologic information. ④ The 2D parameter model building and forward modeling of subtle hydrocarbon trap in target area. According to the formation interpretation of ESS03D seismic area, the 2D parameter model building and seismic wave field forward modeling are carried on the given and predicted subtle hydrocarbon trap with log curve. ⑤ The lithology and fluid identification of subtle trap in target area After study the seismic response characteristics of lithology and fluid in given target area, the optimization of geophysical technique is used for lithology identification and fluid forecast. ⑥The geophysical identification technique system of subtle reservoir The Innovative Points of this Paper ① Based on laboratory measurement and petrophysical model theory, the rock S-wave parameter can be evaluated from conventional log data with probability inverse method. Then the fluid substitution method based on B-G and K-T theory is provided. ② The method and workflow for simulating seismic wave field property of subtle hydrocarbon trap are established based on the petrophysical model building and forward modeling of wave equation. ③ The description of subtle trap structural feature is launched. According to the different reflection of frequency wave field structural attribute, the fluid property of subtle trap can be identified by wave field attenuation attribute and absorption analysis. ④ It’s the first time to identify subtle trap by geophysical technique and provide exploration drilling well location. ⑤ The technique system of subtle reservoir geophysical identification is formed to provide available workflow and research ideas for other region of interest.

叠前叠后联合反演技术及其在QHD32-6油田的应用研究

What geophysical inversion studied includes the common mathematics physical property of inversion and the constitution and appraisal method of solution in geophysics domain, i.e. using observed physical phenomenon from the earth surface to infer space changing and physical property structure of medium within the earth. Seismic inversion is a branch of geophysical inversion. The basic purpose of seismic inversion is to utilizing seismic wave propagating law in the medium underground to infer stratum structure and space distribution of physical property according to data acquisition, processing and interpretation, and then offer the vital foundation for exploratory development. Poststack inversion is convenient and swift, its acoustic impedance inversion product can reflect reservoir interior changing rule to a certain degree, but poststack data lack abundant amplitude and travel time information included in prestack data because of multiple superimpose and weaken the sensitiveness which reflecting reservoir property. Compared with poststack seismic inversion, prestack seismic inversion has better fidelity and more adequate information. Prestack seismic inversion, including waveform inversion, not only suitable for thin strata physical property inversion, it can also inverse reservoir oil-bearing ability. Prestack seismic inversion and prestack elastic impedance inversion maintain avo information, sufficiently applying seismic gathering data with different incident angle, partial angle stack, gradient and intercept seismic data cube. Prestack inversion and poststack inversion technology were studied in this dissertation. A joint inversion method which synthesize prestack elastic wave waveform inversion, prestack elastic impedance inversion and poststack inversion was proposed by making fully use of prestack inversion multiple information and relatively fast and steady characteristic of poststack inversion. Using the proposed method to extract rock physics attribute cube with clear physical significance and reflecting reservoir characterization, such as P-wave and S-wave impedance, P-wave and S-wave velocity, velocity ratio, density, Poisson ratio and Lame’s constant. Regarding loose sand reservoir in lower member of Minghuazhen formation, 32-6 south districts in Qinhuangdao,as the research object, be aimed at the different between shallow layer loose sand and deep layer tight sand, first of all, acquire physical property parameters suitable for this kind of heavy oil pool according to experimental study, establishing initial pressure and shear wave relational model; Afterwards, performing prestack elastic wave forward and inversion research, summarizing rules under the guidance of theoretical research and numerical simulation, performing elastic impedance inversion, calculating rock physics attributes; Finally, predicting sand body distribution according to rock physics parameters, and predicting favorable oil area combine well-logging materials and made good results.