High strain rate tensile properties of rapidly cured woven carbon fibre composites

Tensile tests at high speeds corresponding to automotive crash events were conducted to understand the dynamic properties of rapidly cured woven carbon fiber composites. The High Strain Rate (HSR) experiments were conducted on a servo-hydraulic machine at constant velocities up to a maximum of 25 m/s (82 ft/s). Results from HSR tests were compared with the static results to determine the rate sensitivity of the composite. A high speed camera was used to capture the failure at HSR. The tensile properties of rapidly cured laminate were compared to oven cured laminate to justify its productivity while maintaining the desired properties. The methodology used to achieve constant velocity during HSR tests is discussed in detail. The specimen geometry was specially designed to suit the test rig and to achieve high speeds during tests. All the specimens failed with linear elasticity until sudden brittle fracture. The Scanning Electron Microscopy (SEM) images of the fracture zone were used to identify the failure modes observed at static and high strain rates.

Properties of a carbon-fibre composite modified by electrospun poly (vinylidene fluoride)

The interlaminar toughening of a carbon-fibre reinforced composite by incorporation of electrospun polyvinylidene fluoride (PVDF) nanofibrous membranes was explored in this work. The nanofibres were electrospun directly onto commercial pre-impregnated carbon fibre materials under optimised conditions and PVDF was found to primarily crystallise in its β phase polymorphic form. There is strong evidence from DMTA analysis to suggest that a partial miscibility between the amorphous phases of the PVDF nanofibres and the epoxy exists. The improved plastic deformation at the crack tip after inclusion of the nanofibres was directly translated to a 57% increase in the mode II interlaminar fracture toughness (in-plane shear failure). Conversely, the fracture toughness in mode I (opening failure) was slightly lower than the reference by approximately 20%, and the results were interpreted from the complex micromechanisms of failure arising from the changes in polymorphism of the PVDF.

The indentation behaviour of carbon fibre composite tubes-experiments & modelling

Metallic tubes have been extensively studied for their crashworthiness as they closely resemble automotive crash rails. Recently, the demand to produce lighter weight, yet safer vehicles has led to the need to understand the crash behaviour of novel materials, such as fibre reinforced polymer composites, metallic foams and sandwich structures. This paper discusses the static indentation response of Carbon Fibre Reinforced Polymer (CFRP) tubes. The side impact on a CFRP tube involves various failure mechanisms. This paper highlights these mechanisms and compares the energy absorption of CFRP tubes with similar Aluminium tubes. The response of the CFRP tubes during bending was modelled using ABAQUS finite element software with a composite fabric material model. The material inputs were given based on standard tension and compression test results and the in-plane damage was defined based on cyclic shear tests. The failure modes and energy absorption observed during the tests were well represented by the finite element model.

Rapid fibre diameter measurement in aqueous solutions with OFDA 2000

In this paper, a new technique has been developed to enable fibre diameters to be measured in an aqueous environment using the OFDA 2000 instrument. The existing OFDA instrument has only been used to measure diameters of animal fibres under dry conditions. This new technique was utilised to assess the effects of pH and temperature on the diameters of merino wool fibres in aqueous environments. Significant changes in fibre diameter under aqueous conditions were found as a function of pH and temperature. Wool fibre diameters were at a minimum close to the wool isoelectric point (pH 4.8) and increased at both lower and higher pHs. Swelling of merino wool fibres was observed to increase linearly by around 15% as the temperature rose from ambient to 70°C.

Protein fibre powder

Soft viscoelastic fibres, which are very difficult to grind, can be processed to produce ultrafine particles. This work has created knowledge about new applications of these natural structural proteins. The high reactivity generated through creation of large surface area has been used to design advanced devices and applications. For example particles have been studied for separation of harmful ions from waste water and applied to develop porous composite materials to grow bones to repair critical bone defects.

Enhanced oxygen permeation through perovskite hollow fibre membranes by methane activation

Hollow fibre membranes of mixed conducting perovskite La_0.6Sr_0.4Co_0.2Fe_0.8O₃ (LSCF) were prepared via the combined phase inversion and sintering technique. The fibres were tested for air separation with a home-made reactor under the oxygen partial pressure gradient generated by the air/He streams. Some fibres were in situ activated by introducing methane in the He sweeping gas at high temperatures. The activated membranes with new morphology were created by transforming the inner densified surface layer to a porous structure. Compared to the original membranes, the activated gave appreciable higher oxygen fluxes. At 800 °C, the oxygen fluxes were increased by a factor of 10 after activation was carried out at 1000 °C for 1 h.

High performance BaBiScCo hollow fibre membranes for oxygen transport

Here we report the production of novel high performance BaBi_0.05Sc_0.1Co_0.85O_3-3 (BaBiScCo) hollow fibres delivering oxygen fluxes of 11.4 ml cm^-2 min^-1 at 950 °C. The doping of bismuth, a highly ionic conductor, at the B-site of a barium based perovskite overcame oxygen ionic transport limitations even at temperatures as low as 600 °C.

Modelling of fibre-diameter-dependent light scattering to determine diameter corrections for colour measurement of wool

In this paper, fibre-diameter-dependent light scattering during measurement of wool colour was quantified using the extended multiplicative signal correction technique. Furthermore, a simple-to-apply model has been developed to correct each of the CIE (International Commission on Illumination) X, Y and Z values obtained from colour measurement of fibrous masses. The model was successfully applied to both polypropylene (PP) and wool fibres, though different parameter values were used in each case, indicating different patterns of internal light scattering between PP and wool fibres. After the model corrections, the diameter dependence of measured wool yellowness (Y - Z) was either eliminated or significantly reduced for each of seven sheep flocks distributed widely over the wool-growing regions of Australia.

Needleless electrospinning : influences of fibre generator geometry

The fibre generator shape and dimension are key factors affecting the needleless electrospinning process and fibre fineness. In this work, cylinder with rounded rim, disc and ball were used as spinnerets to electrospin polyvinyl alcohol and polyacrylonitrile solutions. A finite element method was used to analyse how the spinneret geometry affected the electric field generated during electrospinning and the associated changes in fibre diameter and productivity. For cylinder spinnerets, increasing the rim radius reduced the discrepancy of electric field intensity between the cylinder end and middle area, which affected the fibre productivity. The electrospinning failed to operate when the rim radius was over 20 mm. With decreasing cylinder diameter, the electric field intensity in the middle area increased, improving the fibre productivity. Thinner disc spinnerets increased the electric field intensity, resulting in finer nanofibres and higher productivities. Ball spinnerets produced evenly distributed electric field, but failed to electrospin fibres when the diameters were below 60 mm. It has been found that strong and narrowly distributed electric field in the fibre-generating area can significantly facilitate the mass production of quality nanofibres.

Toughening epoxy thermosets and their carbon fibre reinforced composites with electrospun nanofibres

Electrospun nanofibres have emerged as important fibrous materials for diverse applications. They have been shown excellent toughening results when they are applied as interlayer materials between carbon/epoxy laminas in the structural carbon fibre reinforced epoxy matrix composites. They also exhibit synergistic modification effects when they are combined with carbon nanofibres in the thermosetting polymer matrix. In this study, electrospun polyetherketone cardo (PEK-C) nanofibres were used in two ways: directly electrospun onto the surface of carbon fabric [1], and blended with epoxy resin in the form of PEK-C/VGCNF (vapour grown carbon nanofibre) composite nanofibres[2].The interlaminar fracture toughness, flexural properties and thermal mechanical properties of the modified systems were investigated.