Combination of optical and on-destructivemechanicaltechniques for the measurement of maturity in peach

Increasing consumer dissatisfaction related with lack of ripeness in peach has been repeatedly reported since 1990 to the present day. There is thus, a great interest in improving the assessment of peach maturity, currently based on Magness Taylor firmness (destructive, highly variable, and time consuming) and colour (not reliable for highly coloured varieties). The present research studies as an alternative several non-destructive (ND) measurements, based on multispectral imaging, visible spectra, and low mass impact response. Their relationship with maturity, as well as the potential of their combination was studied. As a result, two rather independent (R2 = 0.3) groups of non-destructive measurements, chlorophyll related optical indexes and low mass impact (LMI) measurements, were identified. Optical measurements showed the best behaviour for assessing maturity at harvest, while LMI measurements reflected handling incidences, showing a promising potential to be used to control transport and postharvest handling.

Si and SixGe1-x NWs studied by Raman spectroscopy

Group IV nanostructures have attracted a great deal of attention because of their potential applications in optoelectronics and nanodevices. Raman spectroscopy has been extensively used to characterize nanostructures since it provides non destructive information about their size, by the adequate modeling of the phonon confinement effect. The Raman spectrum is also sensitive to other factors, as stress and temperature, which can mix with the size effects borrowing the interpretation of the Raman spectrum. We present herein an analysis of the Raman spectra obtained for Si and SiGe nanowires; the influence of the excitation conditions and the heat dissipation media are discussed in order to optimize the experimental conditions for reliable spectra acquisition and interpretation.

Medidas de propiedades dieléctricas de materiales de construcción mediante elipsometría

A set of measurements of electromagnetic properties of building materials is presented in this work. The method is based on the measurement of the polarization state of the reflected signal from the material under study at a fixed angle of incidence. From the measured data, by using the Fresnel equations, it has been obtained the dielectric constant. Measurements were done by using two horn antennas at the frequency of 9 GHz. The obtained results are compared with the free space reflexion and transmission Fresnel method and other reflection methods based on a conductor waveguide. The method explained in this work can be used for other type of materials and its main advantage is the non-destructive character and the ease implementation.

Estudio sobre la influencia del contenido de humedad de la madera en ensayos no destructivos para Pinus nigra Arn, Pinus radiata D. Don y Pinus sylvestris L.

El presente proyecto se centra en el estudio de la influencia que ejerce el contenido de humedad en la madera sobre mediciones realizadas mediante diversos ensayos no destructivos (NDT – Non Destructive Tests-). El objetivo es encontrar la relación entre el contenido de humedad de la madera de varias especies del género Pinus (Pinus nigra Arn, Pinus radiata D.Don. y Pinus sylvestris Ait.) y los resultados de diferentes NDT (penetrómetro, resistencia al arranque de tornillos y velocidad de propagación de ondas inducidas y ultrasonidos), y en caso de existir, tratar de elaborar un modelo o factor de corrección que nos permita tener en cuenta dicha influencia en futuros NDT.

Análisis y clasificación de maderas mediante técnicas no invasivas de baja energía

El estudio de materiales, especialmente biológicos, por medios no destructivos está adquiriendo una importancia creciente tanto en las aplicaciones científicas como industriales. Las ventajas económicas de los métodos no destructivos son múltiples. Existen numerosos procedimientos físicos capaces de extraer información detallada de las superficie de la madera con escaso o nulo tratamiento previo y mínima intrusión en el material. Entre los diversos métodos destacan las técnicas ópticas y las acústicas por su gran versatilidad, relativa sencillez y bajo coste. Esta tesis pretende establecer desde la aplicación de principios simples de física, de medición directa y superficial, a través del desarrollo de los algoritmos de decisión mas adecuados basados en la estadística, unas soluciones tecnológicas simples y en esencia, de coste mínimo, para su posible aplicación en la determinación de la especie y los defectos superficiales de la madera de cada muestra tratando, en la medida de lo posible, no alterar su geometría de trabajo. Los análisis desarrollados han sido los tres siguientes: El primer método óptico utiliza las propiedades de la luz dispersada por la superficie de la madera cuando es iluminada por un laser difuso. Esta dispersión produce un moteado luminoso (speckle) cuyas propiedades estadísticas permiten extraer propiedades muy precisas de la estructura tanto microscópica como macroscópica de la madera. El análisis de las propiedades espectrales de la luz laser dispersada genera ciertos patrones mas o menos regulares relacionados con la estructura anatómica, composición, procesado y textura superficial de la madera bajo estudio que ponen de manifiesto características del material o de la calidad de los procesos a los que ha sido sometido. El uso de este tipo de láseres implica también la posibilidad de realizar monitorizaciones de procesos industriales en tiempo real y a distancia sin interferir con otros sensores. La segunda técnica óptica que emplearemos hace uso del estudio estadístico y matemático de las propiedades de las imágenes digitales obtenidas de la superficie de la madera a través de un sistema de scanner de alta resolución. Después de aislar los detalles mas relevantes de las imágenes, diversos algoritmos de clasificacion automatica se encargan de generar bases de datos con las diversas especies de maderas a las que pertenecían las imágenes, junto con los márgenes de error de tales clasificaciones. Una parte fundamental de las herramientas de clasificacion se basa en el estudio preciso de las bandas de color de las diversas maderas. Finalmente, numerosas técnicas acústicas, tales como el análisis de pulsos por impacto acústico, permiten complementar y afinar los resultados obtenidos con los métodos ópticos descritos, identificando estructuras superficiales y profundas en la madera así como patologías o deformaciones, aspectos de especial utilidad en usos de la madera en estructuras. La utilidad de estas técnicas esta mas que demostrada en el campo industrial aun cuando su aplicación carece de la suficiente expansión debido a sus altos costes y falta de normalización de los procesos, lo cual hace que cada análisis no sea comparable con su teórico equivalente de mercado. En la actualidad gran parte de los esfuerzos de investigación tienden a dar por supuesto que la diferenciación entre especies es un mecanismo de reconocimiento propio del ser humano y concentran las tecnologías en la definición de parámetros físicos (módulos de elasticidad, conductividad eléctrica o acústica, etc.), utilizando aparatos muy costosos y en muchos casos complejos en su aplicación de campo. Abstract The study of materials, especially the biological ones, by non-destructive techniques is becoming increasingly important in both scientific and industrial applications. The economic advantages of non-destructive methods are multiple and clear due to the related costs and resources necessaries. There are many physical processes capable of extracting detailed information on the wood surface with little or no previous treatment and minimal intrusion into the material. Among the various methods stand out acoustic and optical techniques for their great versatility, relative simplicity and low cost. This thesis aims to establish from the application of simple principles of physics, surface direct measurement and through the development of the more appropriate decision algorithms based on statistics, a simple technological solutions with the minimum cost for possible application in determining the species and the wood surface defects of each sample. Looking for a reasonable accuracy without altering their work-location or properties is the main objetive. There are three different work lines: Empirical characterization of wood surfaces by means of iterative autocorrelation of laser speckle patterns: A simple and inexpensive method for the qualitative characterization of wood surfaces is presented. it is based on the iterative autocorrelation of laser speckle patterns produced by diffuse laser illumination of the wood surfaces. The method exploits the high spatial frequency content of speckle images. A similar approach with raw conventional photographs taken with ordinary light would be very difficult. A few iterations of the algorithm are necessary, typically three or four, in order to visualize the most important periodic features of the surface. The processed patterns help in the study of surface parameters, to design new scattering models and to classify the wood species. Fractal-based image enhancement techniques inspired by differential interference contrast microscopy: Differential interference contrast microscopy is a very powerful optical technique for microscopic imaging. Inspired by the physics of this type of microscope, we have developed a series of image processing algorithms aimed at the magnification, noise reduction, contrast enhancement and tissue analysis of biological samples. These algorithms use fractal convolution schemes which provide fast and accurate results with a performance comparable to the best present image enhancement algorithms. These techniques can be used as post processing tools for advanced microscopy or as a means to improve the performance of less expensive visualization instruments. Several examples of the use of these algorithms to visualize microscopic images of raw pine wood samples with a simple desktop scanner are provided. Wood species identification using stress-wave analysis in the audible range: Stress-wave analysis is a powerful and flexible technique to study mechanical properties of many materials. We present a simple technique to obtain information about the species of wood samples using stress-wave sounds in the audible range generated by collision with a small pendulum. Stress-wave analysis has been used for flaw detection and quality control for decades, but its use for material identification and classification is less cited in the literature. Accurate wood species identification is a time consuming task for highly trained human experts. For this reason, the development of cost effective techniques for automatic wood classification is a desirable goal. Our proposed approach is fully non-invasive and non-destructive, reducing significantly the cost and complexity of the identification and classification process.

Estudios de eficiencia en el uso de la luz y estimaciones de biomasa en cultivos energéticos de Salix sp. en Central New York, USA

La productividad es un factor importante que influye en la viabilidad económica de un cultivo energético de sauce y maximizarla se convierte en un tema primordial. Esta investigación está directamente relacionada con dicha característica. La productividad varía según los clones cultivados, que pueden ser mejorados y seleccionados genéticamente. Los programas genéticos requieren de una información previa (productividad media en función del porte y número de los tallos, características de las hojas, resistencia a las plagas, etc.) que ayudará a obtener clones más productivos y resistentes. Por ello, nuestra investigación consta de dos estudios: (1) Evaluación de la eficiencia del uso de la luz o LUE (Light Use Efficiency). El incremento de biomasa y la eficiencia del uso de la luz (LUE) fue estudiado en 15 clones del genero Salix durante los meses de junio a septiembre de 2011 en Belleville (Central New York, USA). Los objetivos de este estudio fueron: (1) Evaluar la eficiencia del uso de la luz en la explicación a la variación en la producción de biomasa y (2) Determinar si existen diferencias significativas entre clones evaluando el índice de área foliar (LAI) y algunos componentes de las hojas (N, P, K,…). Se concluye que la variación de biomasa está relacionada con la cantidad de luz interceptada y con la eficiencia de su uso. Dicha información debe de ser transferida para ayudar a mejorar genéticamente los futuros clones a comercializar, con el fin de maximizar la productividad y aumentar la resistencia a plagas. (2) Estimación de biomasa a través de modelos de regresión. Los estudios de investigación relacionados con la productividad requieren estimaciones no destructivas de la biomasa aérea. Sin embargo, el nivel de precisión requerido y la inversión de tiempo son excesivos para operaciones comerciales con grandes extensiones (plantaciones de 10.000 ha). Por esta razón, se estudia el nivel de especificidad (específico, intermedio y general) en la toma de datos de campo sobre los mismos 15 clones (12 de ellos se pueden agrupar en 5 grupos según su genotipo origen) del genero Salix, empleados en el estudio anterior. Para todos los niveles estudiados se observaron diferencias significativas. Pero desde nuestro punto de vista, las diferencias obtenidas no son relevantes. Para validar los modelos finalmente seleccionados se calcularon los porcentajes de error entre la biomasa estimada por los modelos de regresión calculados y la biomasa real obtenida tras los pesajes de biomasa, todo ello se realizó para cada clon según nivel de especificidad. ABSTRACT Productivity is an important factor in the economic viability of a willow crop´s, therefore, maximize it becomes a major factor. This study is directly related to this feature. Productivity, among other factors, may vary depending on different clones, which can be improved and selected genetically. Genetic programs require prior information (average productivity, size and number of stems, leaf characteristics, resistance to pests, etc.) to help you get more productive clones resistant to local pests. Our research consists of two studies: (1) Evaluation of the efficiency of use of light (LUE, Light Use Efficiency). The increase of biomass and light use efficiency (LUE) was tested on 15 clones of the genus Salix during June and September 2011 in Belleville (Central New York, USA). The objectives of this study were: (1) evaluate the light use efficiency and its relationship with the variation in biomass production and (2) determine whether there are significant differences between clones evaluating the leaf area index (LAI) and some traits of the leaves (N, P, K). We studied the correlation with the light use efficiency. It is concluded that the variation of biomass was related to the amount of light intercepted and its efficiency. Such information must be transferred to help improve future genetically clones to market in order to maximize productivity and increase resistance to pests. (2) Estimation of biomass through regression models. Research studies related to productivity estimates require precision and non destructive biomass. However, the level of accuracy required and the investment of time are excessive for large commercial operations with extensions (plantations of 10,000 ha). Precisely for this reason, we study the level of specificity (specific, intermediate and general) in making field data on the same 15 clones (12 of them can be grouped into five groups according to their genotype origin) of the genus Salix, employees in the previous study. For all levels studied some significant differences were observed. But from our practical standpoint, the differences are not relevant. Finally, to validate the selected models, we calculated the percent of bias between estimated biomass (by the regression models) and real biomass obtained after the weighing of biomass, all this process was done for each clone by level of specificity.

Application of photoreflectance to advanced multilayer structures for photovoltaics

Photoreflectance (PR) is a convenient characterization tool able to reveal optoelectronic properties of semiconductor materials and structures. It is a simple non-destructive and contactless technique which can be used in air at room temperature. We will present experimental results of the characterization carried out by means of PR on different types of advanced photovoltaic (PV) structures, including quantum-dot-based prototypes of intermediate band solar cells, quantum-well structures, highly mismatched alloys, and III?V-based multi-junction devices, thereby demonstrating the suitability of PR as a powerful diagnostic tool. Examples will be given to illustrate the value of this spectroscopic technique for PV including (i) the analysis of the PR spectra in search of critical points associated to absorption onsets; (ii) distinguishing signatures related to quantum confinement from those originating from delocalized band states; (iii) determining the intensity of the electric field related to built-in potentials at interfaces according to the Franz?Keldysh (FK) theory; and (v) determining the nature of different oscillatory PR signals among those ascribed to FK-oscillations, interferometric and photorefractive effects. The aim is to attract the interest of researchers in the field of PV to modulation spectroscopies, as they can be helpful in the analysis of their devices.

Models for Internal Quality Fruit Sorting, Based on Time- Domain Laser Reflectance Spectroscopy (TDRS)

Time domain laser reflectance spectroscopy (TDRS) was applied for the first time to evaluate internal fruit quality. This technique, known in medicine-related knowledge areas, has not been used before in agricultural or food research. It allows the simultaneous non-destructive measuring of two optical characteristics of the tissues: light scattering and absorption. Models to measure firmness, sugar & acid contents in kiwifruit, tomato, apple, peach, nectarine and other fruits were built using sequential statistical techniques: principal component analysis, multiple stepwise linear regression, clustering and discriminant analysis. Consistent correlations were established between the two parameters measured with TDRS, i.e. absorption & transport scattering coefficients, with chemical constituents (sugars and acids) and firmness, respectively. Classification models were built to sort fruits into three quality grades, according to their firmness, soluble solids and acidity.

Relationship between solar radiation on watercore on apple fruit assessed with MRI

This work is a preliminary studio of the possibility of assess a relationship between solar radiation and watercore development on apple fruit, during maturation, using a non destructive method such as Magnetic Resonance Imaging (MRI). For such purpose, several low cost solar radiation sensors were designed for the trial and placed at 2 different heights (1.5 and 2.5 m) on 6 adult ?Esperiega? apple trees, in a commercial orchard in Ademuz (Valencia). Sensors were connected along 27 days, during the end of the growth period and start of the fruit maturation process, and radiation measurements of the a-Si sensors were recorded every 1 minute. At the end of this period, fruits from the upper and the lower part of the canopy of each tree were harvested. In all, 152 apples were collected and images with MRI. A Principal Component Analysis, perfomed over the histograms of the images, as well as segmentation methods were performed on the MR images in order to find a pattern involving solar radiation and watercore incidence.

Assessment of watercore development in apples with MRI: Effect offruit location in the canopy

tWatercore distribution inside apple fruit (block or radial), and its incidence (% of tissue) were relatedto the effect of solar radiation inside the canopy as measured by a set of low-cost irradiation sensors.221 samples were harvested in two seasons from the top and the bottom of the canopy and submittedto the non-invasive and non-destructive technique of magnetic resonance imaging (MRI) in order toobtain 20 inner tomography slices from each fruit and analyze the damaged areas using an interactive3D segmentation method. The number of fruit corresponding to each type of damage and the relevantpercentage were calculated and it was found that apples from the top of the tree were mainly of the radialtype (84%) and had more watercore (approx. 5% more) than apples from the bottom (65% radial). From theimage segmentation, the Euler number, a morphometric parameter, was extracted from the segmentedimages and related to the type of watercore symptoms. Apples with block watercore were grouped inEuler numbers between −400 and 400 with a small evolution. For apples with radial development, theEuler number was highly negative: up to −1439. Significant differences were also found regarding sugarcomposition, with higher fructose and total sugar contents in apples from the upper canopy, compared tothose in the lower canopy location. In the seasons studied (2011 and 2012), significantly higher sorbitoland lower sucrose and fructose contents were found in watercore-affected tissue compared to the healthytissue of affected apples and also compared to healthy apples.

Effect of impacting radius of curvature on firmness sensing of fruits in a sorting system.

Fruits of two varieties of both apples and pear were tested to measure their response to small energy impact applied by a impact tester with two spherical tips of different radious of curvature ( RA = 2.48 cm and RB = 0.98 cm) and equal mass were used. In the four varieties studied, the size of bruise was smaller with a spherical tip RA than with tip RB . The non-destructive impact test would cause less damage with a spherical impactor with a radious bigger than 0.98 cm.

Mealiness assessment in fruits using MRI techniques.

Mealiness is a sensory attribute that cannot be defined by a single parameter but through a combination of variables (multidimensional structure). Previous studies propose the definition of mealiness as the lack of crispiness, of hardness and of juiciness. Current aims are focused on establishing non destructive tests for mealiness assessment. MultiSliceMultiEcho Magnetic resonance images (MRI, 64*64pixels) have been taken corresponding to a 3ms of Echo time. Small samples of Top Red apples stored 6 months at controlled atmosphere (expected to be non mealy) and 2°C (expected to be mealy) have been used for MRI imaging. Three out of four apples corresponding to the sample maintained at controlled atmosphere did not develop mealiness while three out of four fruits corresponding to the sample stored at 2°C became mealy after 6 month of storage. The minimum T2 values/image obtained for the mealy apples shows to be significantly lower when compared with non mealy apples pointing that a more dis-aggregated structure leads to a quicker loss of signal Also, there is a significant linear correlation (r=-0.76) between the number of pixels with a T2 value below 35ms within a fruit image and the deformation parameter registered during the Magness-Taylor firmness test. Finally, all the T2 images of the mealy apples show a regional variation of contrast which is not shown for non mealy apples. This variation of contrast is similar to the MRI images of water-cored apples indicating that in these cases there is a differential water movement that may precede the internal browning.

Storabelity of melon for different ripeness stages at harvest. Selection of instrumental procedures for quality assessment.

The consumption of melon (Cucumis melo L.) has been, until several years ago, regional, seasonal and without commercial interest. Recent commercial changes and world wide transportation have changed this situation. Melons from 3 different ripeness stages at harvest and 7 cold storage periods have been analysed by destructive and non destructive tests. Chemical, physical, mechanical (non destructive impact, compression, skin puncture and Magness- Taylor) and sensory tests were carried out in order to select the best test to assess quality and to determine the optimal ripeness stage at harvest. Analysis of variance and Principal Component Analysis were performed to study the data. The mechanical properties based on non-destructive Impact and Compression can be used to monitor cold storage evolution. They can also be used at harvest to segregate the highest ripeness stage (41 days after anthesis DAA) in relation to less ripe stages (34 and 28 DAA).Only 34 and 41 DAA reach a sensory evaluation above 50 in a scale from 0-100.

Mealiness assessment in apples and peaches using MRI techniques.

Since Januarv 1946 a wade EC Project entitled "Mealiness in fruits Consumers perception and means for detection is being carried out. Mealiness is a sensory attribute that cannot be defined by a single parameter but through a combination of variables (multidimensional structure) Previous studies propose the definition of mealiness as the lack of crispiness of hardness and of juiciness. A destructive instrumental procedure combined with a integration technique has been already developed enabling to identify mealy fruits by destructive instrumental means use other contributions of Barreiro and Ortiz to this Ag Eng 98. Current aims .are focused on establishing non destructive tests for mealiness assessment. Magnetic resonance Imaging (MRI) makes use of the magnetic properties that some atomic nuclei have. especially hidrogen nuclei from water molecules to obtain high quality images in the field of internal quality evaluation the MRI has been used to assess internal injury due to conservation as o treatments as chilling injury un Persimmons Clark&Forbes (1994) and water-core in apples (Wang et al. 1998. In the case of persimmons the chilling injury is described as an initial tissue breakdown and lack of cohesion between cells followed by formation of a firm gel and by a lack of juiciness without changes in the total amount ol water content. Also a browning of the flesh is indicated (Clark&Forhes 1994). This definition fits into the previous description of mealiness.

Models for internal quality sorting of fruit, based on time-domain laser reflectance spectroscopy (TDRS).

Non-destructive measurement of fruit quality has been an important objective through recent years (Abbott, 1999). Near infrared spectroscopy (NIR) is applicable to the cuantification of chemicals in foods and NIK "laser spectroscopy" can be used to estimate the firmness of fruits. However, die main limitation of current optical techniques that measure light transmission is that they do not account for the coupling between absorption and scattering inside the tissue, when quantifying the intensity o f reemitted light. The solution o f this l i m i t a t i o n was the goal o f the present work.