DDES of a supersonic coaxial helium jet

The mixing of a light gas in a scramjet combustion chamber is replicated through the simulation of a supersonic coaxial helium jet. Sensitivities of the RANS method to model constants is presented and the DDES method is employed to try and alleviate this modelling weakness. A significant delay in the shear layer transition is found to occur in the DDES simulation and it is suggested this may be due to the absence of inlet turbulence. The influence of the introduction of inflow turbulence is investigated and computational results are compared to experimental data. The influence of model constants on the DDES results are presented. © 2012 by Peter Cocks.

Optical trapping of nanotubes with cylindrical vector beams

We use laser beams with radial and azimuthal polarization to optically trap carbon nanotubes. We measure force constants and trap parameters as a function of power showing improved axial trapping efficiency with respect to linearly polarized beams. The analysis of the thermal fluctuations highlights a significant change in the optical trapping potential when using cylindrical vector beams. This enables the use of polarization states to shape optical traps according to the particle geometry, as well as paving the way to nanoprobe-based photonic force microscopy with increased performance compared to a standard linearly polarized configuration. © 2012 Optical Society of America.

All optical degenerate mode-group multiplexing using a Mode Selective Switch

A Mode Selective Switch based around an LCoS Spatial Light Modulator is demonstrated to optically demultiplex modes with the same propagation constants to the same output fibres, using a common phase mask for all channels. © 2012 IEEE.

Sintered metal foams for acoustic absorption

Metal foams fabricated via sintering offer novel mechanical and acoustic properties. Previously, polymer foams have been used as a means of absorbing acoustic energy. However, the structural applications of these foams are limited. The metal sintering approach offers a cost-effective means for the mass-production of open-cell metal foams. The static flow resistance of sintered metal foams was characterized for a range of practical pore sizes and porosities. The measured values for the flow resistance were subsequently used in a phenomenological acoustic model to predict the impedances and propagation constants of the foams. The predictions were then compared to acoustic measurements. At low frequencies (0-1000Hz), the phenomenological model captures the magnitude and frequency dependence of the absorption. At higher frequencies, as expected, the phenomenological model underpredicted the acoustic properties of the foams. However, an alternative microstructural model demonstrated good correlation to the measured results in this frequency range. The effects of foam type and arrangement on the absorption pattern were examined. General trends were identified for enhancing the low frequency performance of an acoustic absorber incorporating sintered foams.

Plasmonic band gaps and waveguide effects in carbon nanotube arrays based metamaterials

Highly dense periodic arrays of multiwalled carbon nanotubes behave like low-density plasma of very heavy charged particles, acting as metamaterials. These arrays with nanoscale lattice constants can be designed to display extended plasmonic band gaps within the optical regime, encompassing the crucial optical windows (850 and 1550 nm) simultaneously. We demonstrate an interesting metamaterial waveguide effect displayed by these nanotube arrays containing line defects. The nanotube arrays with lattice constants of 400 nm and radius of 50 nm were studied. Reflection experiments conducted on the nanoscale structures were in agreement with numerical calculations.

Brillouin scattering of cluster-assembled carbon films

The low frequency vibrational spectrum of cluster beam deposited carbon films was studied by Brillouin light scattering. In thin films the values of both bulk modulus and shear modulus has been estimated from the shifts of surface phonon peaks. The values found indicate a mainly sp2 coordinated random network with low density. In thick films a bulk longitudinal phonon peak was detected in a spectral range compatible with the value of the index of refraction and of the elastic constants of thin films. High surface roughness, combined with a rather strong bulk central peak, prevented the observation of surface phonon features. © 1998 Elsevier Science Ltd. All rights reserved.

Particulate matter emission during start-up and transient operation of a spark-ignition engine

In order to understand why emissions of Particulate Matter (PM) from Spark-Ignition (SI) automobiles peak during periods of transient operation such as rapid accelerations, a study of controlled, repeatable transients was performed. Time-resolved engine-out PM emissions from a modern four-cylinder engine during transient load and air/fuel ratio operation were examined, and the results could be fit in most cases to a first order time response. The time constants for the transient response are similar to those measured for changes in intake valve temperature, reflecting the strong dependence of PM emissions on the amount of liquid fuel in the combustion chamber. In only one unrepeatable case did the time response differ from a first order function: showing an overshoot in PM emissions during transition from the initial to the final steady state PM emission level. PM emissions during controlled, motored start-up experiments show a peak at start-up followed by a period during which emissions are either relatively constant or drift somewhat. When the fuel injection and ignition are shut off, PM emissions also peak briefly, but rapidly decay to low levels. Qualitative implications on the study and modeling of PM emissions during transient engine operation are discussed. Copyright © 1999 Society of Automotive Engineers, Inc.

Modelling the vibration of tyre sidewalls

The dynamical behaviour of the sidewall has an important influence on tyre vibration characteristics. Nonetheless, it remains crudely represented in many existing models. The current work considers a geometrically accurate, two-dimensional, sidewall description, with a view to identifying potential shortcomings in the approximate formulations and identifying the physical characteristics that must be accounted for. First, the mean stress state under pressurisation and centrifugal loading is investigated. Finite-Element calculations show that, while the loaded sidewall shape remains close to a toroid, its in-plane tensions differ appreciably from the associated analytical solution. This is largely due to the inability of the anisotropic sidewall material to sustain significant azimuthal stress. An approximate analysis, based on the meridional tension alone, is therefore developed, and shown to yield accurate predictions. In conjunction with a set of formulae for the 'engineering constants' of the sidewall material, the approximate solutions provide a straightforward and efficient means of determining the base state for the vibration analysis. The latter is implemented via a 'waveguide' discretisation of a variational formulation. Its results show that, while the full geometrical description is necessary for a complete and reliable characterisation of the sidewall's vibrational properties, a one-dimensional approximation will often be satisfactory in practice. Meridional thickness variations only become important at higher frequencies (above 500 Hz for the example considered here), and rotational inertia effects appear to be minor at practical vehicle speeds. © 2013 Elsevier Ltd. All rights reserved.

2x56-Gb/s mode-division multiplexed transmission over 2km of om2 multimode fibre without MIMO equalization

A Spatial Light Modulator is used to optically demultiplex modal channels on the basis of degenerate propagation constants using a shared phase mask for all channels. This allows groups of modes to be routed to common output fibres eliminating the need for MIMO equalization to transmit 2x56Gb/s QPSK over 2km of OM2 grade 50μm core MMF. © 2012 OSA.

Investigating vibration dyanmics of cross-coupled MEMS resonators for reduced motional resistance

This paper investigates the vibration dynamics of a closed-chain, cross-coupled architecture of MEMS resonators. The system presented here is electrostatically transduced and operates at 1.04 MHz. Curve veering of the eigenvalue loci is used to experimentally quantify the coupling spring constants. Numerical simulations of the motional resistance variation against induced perturbation are used to assess the robustness of the cross-coupled system as opposed to equivalent traditional open-ended linear one-dimensional coupling scheme. Results show improvements of as much as 32% in the motional resistance between the cross-coupled system and its one-dimensional counterpart. © 2013 IEEE.

Static analysis of Euler-Bernoulli beams with multiple unilateral cracks under combined axial and transverse loads

The paper deals with the static analysis of pre-damaged Euler-Bernoulli beams with any number of unilateral cracks and subjected to tensile or compression forces combined with arbitrary transverse loads. The mathematical representation of cracks with a bilateral behaviour (i.e. always open) via Dirac delta functions is extended by introducing a convenient switching variable, which allows each crack to be open or closed depending on the sign of the axial strain at the crack centre. The proposed model leads to analytical solutions, which depend on four integration constants (to be computed by enforcing the boundary conditions) along with the Boolean switching variables associated with the cracks (whose role is to turn on and off the additional flexibility due to the presence of the cracks). An efficient computational procedure is also presented and numerically validated. For this purpose, the proposed approach is applied to two pre-damaged beams, with different damage and loading conditions, and the results so obtained are compared against those given by a standard finite element code (in which the correct opening of the cracks is pre-assigned), always showing a perfect agreement. © 2013 Elsevier Ltd. All rights reserved.

2×56-Gb/s mode-division multiplexed transmission over 2km of OM2 multimode fibre without MIMO equalization

A Spatial Light Modulator is used to optically demultiplex modal channels on the basis of degenerate propagation constants using a shared phase mask for all channels. This allows groups of modes to be routed to common output fibres eliminating the need for MIMO equalization to transmit 2×56Gb/s QPSK over 2km of OM2 grade 50μm core MMF. © 2012 Optical Society of America.

2x56-Gb/s mode-division multiplexed transmission over 2km of OM2 multimode fibre without MIMO equalization

A Spatial Light Modulator is used to optically demultiplex modal channels on the basis of degenerate propagation constants using a shared phase mask for all channels. This allows groups of modes to be routed to common output fibres eliminating the need for MIMO equalization to transmit 2x56Gb/s QPSK over 2km of OM2 grade 50μm core MMF. © 2012 OSA.

EXPERIMENTS ON AQUATIC ECOSYSTEM REGIME SHIFT IN ENCLOSURES NEAR LAKE DIANCHI, CHINA

To discover how a lake converts from a turbid state to clean state, and what drives this process, we constructed controlled enclosure ecosystems and used the ecological remediation method to force ecosystems to convert from the turbid state to the clean state. Our results show that the driving forces include temperature., macrophyte, silver carp and mussel, which form a combined force to drive the controlled ecosystem to switch. There is a threshold existing in treated enclosure ecosystem during the conversion from turbid to clean state. When TP <0.09 mg.L-1, Chl-a <0.036 mg.L-1, transparency >62 cm, TN <2.15 mg.L-1, CODMn <13.7 mg.L-1, tubidity <10, and the number of algal cells <10(6) cells.L-1, the treated ecosystem changes sharply from turbid to clean state. The conversion process can be divided into three phases: turbid state, clean-turbid transitional state as well as clean state, and described with the power function Y = a*X-b (where Y is water parameter, X is time, a and b are constants), which indicates that the shift in the enclosure ecosystem from turbid to clean state is discontinuous.

Characterization and deformation response of orthotropic fibre networks with auxetic out-of-plane behaviour

In the present paper, highly porous fibre networks made of 316L fibres, with different fibre volume fractions, are characterized in terms of network architecture, elastic constants and fracture energies. Elastic constants are measured using quasi-static mechanical and modal vibration testing, yielding local and globally averaged properties, respectively. Differences between quasi-static and dynamic elastic constants are attributed to through-thickness shear effects. Regardless of the method employed, networks show signs of material inhomogeneity at high fibre densities, in agreement with X-ray nanotomography results. Strong auxetic (or negative Poisson's ratio) behaviour is observed in the through-thickness direction, which is attributed to fibre kinking induced during processing. Measured fracture energies are compared with model predictions incorporating information about in-plane fibre orientation distribution, fibre volume fraction and single fibre work of fracture. Experimental values are broadly consistent with model predictions, based on the assumption that this energy is primarily associated with plastic deformation of individual fibres within a process zone of the same order as the inter-joint spacing. © 2013 Published by Elsevier Ltd. on behalf of Acta Materialia Inc. All rights reserved.