Effective herding of flatfish by cables with minimal seafloor contact

Otter trawls are very effective at capturing flatfish, but they can affect the seaf loor ecosystems where they are used. Alaska f latf ish trawlers have very long cables (called sweeps) between doors and net to herd fish into the path of the trawl. These sweeps, which ride on and can disturb the seaf loor, account for most of the area affected by these trawls and hence a large proportion of the potential for damage to seaf loor organisms. We examined modifications to otter trawls, such that disk clusters were installed at 9-m intervals to raise trawl sweeps small distances above the seafloor, greatly reducing the area of direct seafloor contact. A critical consideration was whether flatfish would still be herded effectively by these sweeps. We compared conventional and modified sweeps using a twin trawl system and analyzed the volume and composition of the resulting catches. We tested sweeps raised 5, 7.5, and 10 cm and observed no significant losses of flatfish catch until sweeps were raised 10 cm, and those losses were relatively small (5–10%). No size composition changes were detected in the flatfish catches. Alaska pollock (Theragra chalcogramma) were captured at higher rates with two versions of the modified sweeps. Sonar observations of the sweeps in operation and the seaf loor after passage confirmed that the area of direct seafloor contact was greatly reduced by the modified sweep

Versuche zur Verringerung des Dorschbeifanges in Grundschleppnetzen

Bottom otter trawls with cut back upper panels were tested in the fischeries on Baltic Sea flounder and North Sea plaice to reduce cod by-catch. In a first series of experiments on board the fishing research cutter “Clupea” the cod-bycatch was reduced by 63 %. The catch of flounder was by 92 % higher in the cut back trawl. The same trawl with the same experimental set-up achieved aboard the fisching research vessel “Solea” on the other hand a reduction in cod-bycatch by 69 %. The catch of flounder was 23,3 % lesser in the topless trawl, which was in contrast to the “Clupea” trials. In the second series of experiments with the same cut back trawl the splits were shortened to reduce the net opening height from 0,9 m to 0,6 m previously. The cod-bycatch was reduced by 86 % and the catch of flounder was 81 % higher in comparison to the complete trawl. A prototype made of stronger net material but based on the cutting and rigging design of the tested cut back trawl with the shortened splits was tested with commercial twin trawlers. The cod-bycatch was reduced by 82,2 %, the catch of plaice by 43,3 % and the catch of dab by 44,6 % in the comparison to the commercial used trawl TV280. The flounder catch was in the topless trawl 10 % higher. In the North Sea in the comparison to a bottom trawl TV300 the cod by-catch was reduced by 89,8 %, but the catch of plaice and dab were 54 % and 58,7 % lesser. In the next step was a prototype of a normally in the North Sea plaice fisheries used trawl tested with a cut back of 2 m only. The cod catch was reduced by 16,9 % but the plaice catch, however , by 22,3 %. Kurzfassung Schleppnetze mit verkürzten Oberblättern wurden in der Fischerei auf Ostseeflunder und Nordseescholle zur Verringerung des Dorschbeifanges erprobt. In einer ersten Versuchsserie mit dem Forschungskutter „Clupea“ wurde der Dorschbeifang um 63 % reduziert. Die Fänge der Zielart Flunder waren im reduzierten Schleppnetz dagegen um 92 % höher. Das gleiche Schleppnetz mit gleichem Versuchsaufbau erzielte auf dem Fischereiforschungsschiff „Solea“ dagegen eine Reduktion des Dorschbeifanges um 69 %, wobei im Gegensatz zu den „Clupea“-Versuchen der Flunderfang um 23,3 % im reduzierten Netz geringer war. In der zweiten Versuchsserie wurden die Netzstander am reduzierten Schleppnetz verkürzt, um die Netzöffnungshöhe zu verringern. Dadurch wurde der Dorschbeifang in Versuchen mit dem Forschungskutter „Clupea“ um 86 % verringert und die Flunderfänge waren im reduzierten Schleppnetz 81 % höher. Basierend auf dem Zuschnitt des erprobten Schleppnetzes, jedoch aus stärkerem Netzmaterial gefertigt, wurde ein Prototyp auf kommerziellen Doppelnetz-Kuttern erprobt. In der Ostsee wurde in diesen Versuchen der Dorschbeifang um 82,2 %, der Schollenfang um 43,3 % und der Klieschenfang um 44,6 % mit dem im Oberblatt verkürztem Schleppnetz im Vergleich zum Kutterschleppnetz TV280 reduziert. Der Flunderfang war im reduzierten Schleppnetz 10 % höher. Auf der Nordsee wurde mit diesem Versuchsnetz im Vergleich zu einem TV 300 der Kabeljaubeifang um 89,8 % verringert, die Schollenfänge waren jedoch 54 % geringer und die Klieschenfänge 58,7 % geringer als im Vergleichsnetz. In einer weiteren Variante wurde ein in der Nordseeschollenfischerei verwendetes Grundschleppnetz mit 2 m geringfügig im Oberblatt zurückgeschnitten und mit dem Prototyp auf einem Doppelnetz-Heckschlepper verglichen. Der Kabeljaubeifang wurde dadurch um 16,9 % der Schollenfang aber um 22,3 % verringert

Avaliação de propriedades mecânicas e térmicas de compósito à base de polietileno de alta densidade e hidroxiapatita deficiente de cálcio

No presente trabalho, foram processados compósitos de polietileno de alta densidade (PEAD) com hidroxiapatita deficiente de cálcio (HA), com o objetivo de obter materiais com melhores propriedades mecânicas e bioatividade. A adição da HA deficiente de cálcio proporcionou um aumento no módulo de elasticidade (maior rigidez), menor resistência ao impacto e decréscimo do grau de cristalinidade do PEAD, proporcionando uma maior bioatividade ao material. A análise térmica exploratória (sistema não isotérmico) foi realizada por meio da técnica de calorimetria exploratória diferencial (DSC) e foram avaliados os teores de fosfato de cálcio e a velocidade de rotação da rosca no processamento dos materiais. No estudo da cristalização não-isotérmica observou-se uma diminuição da temperatura de cristalização com o aumento da taxa de resfriamento para todos os materiais sintetizados. A energia de ativação (Ea) da cristalização dos materiais foi avaliada por meio dos métodos Kissinger e Ozawa. A amostra com 5% de HA deficiente de cálcio e velocidade de processamento de 200 rpm foi a que apresentou menor valor de energia de ativação, 262 kJ/mol, menor desvio da linearidade e a que mais se assemelhou à matriz de PEAD sem HA. O teor de hidroxiapatita deficiente de cálcio não favorece o processo de cristalização devido à alta energia de ativação determinada pelos métodos descritos. Provavelmente, a velocidade de rotação, favorece a dispersão da carga na matriz de PEAD, dificultando o processo de cristalização. Na aplicação do método de Osawa-Avrami, os coeficientes de correlação indicaram perda na correlação linear. Estas perdas podem estar associadas a uma pequena percentagem de cristalização secundária e/ou à escolha das temperaturas utilizadas para determinar a velocidade de cristalização. Na determinação dos parâmetros pelo método de Mo, as menores percentagens de cristalização apresentaram um grande desvio da linearidade, com coeficiente de correlação bem menor que 1 e com o aumento da percentagem de cristalização, o desvio da linearidade diminui, ficando próximo de 1. Os resultados obtidos mostraram que o modelo de Mo e de Osawa-Avrami não foram capazes de definir o comportamento cinético dos materiais produzidos neste trabalho.

Propriedades mecânicas e análise térmica de resíduos de polietileno de alta densidade (PEAD) reciclado

Atualmente grande parte dos resíduos descartados rotineiramente no Brasil é composta por material plástico como, por exemplo, o polietileno de alta densidade (PEAD), o qual é muito comum no lixo doméstico. Nesta Dissertação, embalagens de PEAD pós-consumo foram coletadas e moídas. Após processamento em extrusora, o material definido como PEAD reciclado (mistura de embalagens brancas, marfins e incolores) foi injetado e as propriedades mecânicas foram avaliadas e comparadas com uma amostra de PEAD comercial (HD7600U). A análise térmica através da calorimetria exploratória diferencial (DSC), em conjunto com a análise estatística dos resultados experimentais, também foi conduzida. Em relação à resistência à tração, a diferença entre as amostras de PEAD reciclado e PEAD comercial foram tão pouco expressivas que, dentro das condições experimentais adotadas, se pode afirmar que o material reciclado é equivalente ao comercial.Por sua vez, os modelos cinéticos aplicados na análise térmica revelaram quea amostra de PEAD comercial demonstra um processo de nucleação e crescimento dos cristais mais homogêneo e simples, embora a energia de ativação seja consideravelmente maior do que o das demais amostras de PEAD.

Noise suppression in monolithically integrated Michelson interferometer

A novel monolithically integrated Michelson interferometer using intersecting twin-contact semiconductor optical amplifiers is proposed and implemented whereby the two arms are gain imbalanced to give enhanced noise suppression. Experimental OSNR improvements of 8.4 dB for pulses with durations 8 ps and by default ER of 14 dB are demonstrated for low driving currents of between 25 and 30 mA. This is believed to be the smallest Michelson interferometer to date.

Development of low entropy coding in a recurrent network.

In this paper we present an unsupervised neural network which exhibits competition between units via inhibitory feedback. The operation is such as to minimize reconstruction error, both for individual patterns, and over the entire training set. A key difference from networks which perform principal components analysis, or one of its variants, is the ability to converge to non-orthogonal weight values. We discuss the network's operation in relation to the twin goals of maximizing information transfer and minimizing code entropy, and show how the assignment of prior probabilities to network outputs can help to reduce entropy. We present results from two binary coding problems, and from experiments with image coding.

Soil conditioning under London

The CTRL Contract 220 covered 7.5km twin-bore tunnels excavated between late 2002 and early 2004 from Stratford Box to St Pancras station in Central London. To ensure efficient machine operation as well as the transport and disposal of soil, soil conditioning treatments were applied. Specifically, the foam injection ratio (FIR) and the polymer injection ratio (PIR) (injected volume of foam and polymer solution expressed as a percentage of the excavated soil volume) were employed. It was found that carefully selected soil conditioning allowed chamber pressures of 200kPa or more to be accurately controlled in the stiff London Clay and to an extent, in the very stiff clays of the Lambeth Group. Average FIRs of 50% and PIRs of 7 and 9% were used in the Thanet Sand and in the Lambeth Group Clays. In contrast, much lower quantities of foam were used in the London Clay.

Monitoring tunnel deformation induced by close-proximity bored tunneling using distributed optical fiber strain measurements

The paper describes the use of optical fiber Brillouin Optical Time Domain Reflectometry (BOTDR) to monitor the strain distribution in an existing tunnel while a twin tunnel was bored at close-proximity. The twin circular bored tunnels between Serangoon and Bartley stations on the new Circle Line Stage 3 subway in Singapore were constructed at close-proximity to avoid underpinning the foundations of adjacent buildings. The minimum clear separation of the two tunnels is 2.3m (0.4 times the tunnel diameter). The Outer Tunnel was constructed first, followed by the Inner Tunnel, with the earth-pressure balance tunnel boring machines maintained at a minimum of 100m apart. In this trial application of BOTDR, the strain distribution along the Outer Tunnel was measured, in order to monitor its deformation due to the boring of the Inner Tunnel at close-proximity. The aim of the trial application was to determine the practicality of this monitoring method for future use in 'live' tunnels. This paper compares the measurements obtained from optical fiber BOTDR with conventional methods of tunnel monitoring and describes preliminary installation and workmanship guidelines derived from lessons learnt during this trial. © 2007 ASCE.

Development of intermediate moisture marinated fish product and its storage characteristics

An attempt was made to prepare an intermediate moisture (around 44% moisture) marinated (pH around 4) fish product. Fillets from Sciaenid fish (each fish weighing 70-80 gm) were dipped in a solution containing 7% acetic acid, 20% common salt and 1% propionic acid for 2 hours. After soaking, the soaked fillets were partially dried to about 44% moisture. Three effective hurdles like low pH (by using 7% acetic add and 1% propionic acid), low water activity (by using 20% salt and partially drying the fillets) and preservative (1% propionic add), were used to prepare a shelf-stable product at room temperature. The dried product was sprayed with 0.0 5% BHA in 50% alcohol and further dried for 10 minutes to remove added water and alcohol, thereby another hurdle (preservative) against fat oxidation. The product was packed in 300 gauge polythene bags and stored in transparent screw cap plastic jars. Fortnightly samples were drawn and subjected to biochemical, bacteriological and organoleptic evaluation to study its storage characteristics. The product was in good acceptable form up to 4 months at ambient temperature. The product needed one hour soaking in water with two changes of water in between to make it free from excess salt and acid smell.

Preliminary observations in the design and operation of a three panel, double trawl net

Fishing operations were conducted off Kakinada using a 3 panel double trawl net with twin cod-ends to study the utility of the net in catching both bottom and off bottom fishes. The observations indicate that the net is effective in simultaneous catching of bottom as well as off-bottom fishes and separating them while in operation. The design details of the net and the particulars of the fishing operations conducted are presented.

A study of Rastrineobola argentea (Pellegrin), (Pisces : Cyprinidae) and its importance in the fisheries of Lake Kyoga and the northern waters of Lake Victoria

Rastrineobola argentea is the only native fish species which is still abundant in Lakes Victoria and Kyoga, the others being two introduced species; Lates niloticus and Oreochromis niloticus. It forms an important commercial fishery in Lake Victoria and is very important as food of Lates niloticus in both lakes. The depletion of the originally abundant insectivorous and zooplanktivorous hap lochromines due to predation by Lates niloticus appears to have favoured it by reducing potential competitors for food. It now consumes a wide range of invertebrate organisms that originally used to be eaten by different specialised species of haplochromines which include: larvae and pupae of chironomids and chaoborids, copepods and ostracods. Its size in Lake Kyoga (where the Nile perch was introduced earlier) has, however, decreased and is smaller than that in Lake Victoria probably due to high predation pressure. The twin effect of predation and fishing are likely to exert heavy pressure on the species. Research is therefore required to provide information for its management.

The effects of a second tunnel on the propagation of ground-borne vibration from an underground railway

Accurate predictions of ground-borne vibration levels in the vicinity of an underground railway are greatly sought in modern urban centers. Yet the complexity involved in simulating the underground environment means that it is necessary to make simplifying assumptions about this environment. One such commonly-made assumption is to model the railway as a single tunnel, despite many underground railway lines consisting of twin-bored tunnels. A unique model for two tunnels embedded in a homogeneous, elastic full space is developed. The vibration response of this two-tunnel system is calculated using the superposition of two displacement fields: one resulting from the forces acting on the invert of a single tunnel, and the other resulting from the interaction between the tunnels. By partitioning of the stresses into symmetric and anti-symmetric mode number components using Fourier decomposition, these two displacement fields can by calculated with minimal computational requirements. The significance of the interactions between twin-tunnels is quantified by calculating the insertion gains that result from the existence of a second tunnel. The insertion-gain results are shown to be localized and highly dependent on frequency, tunnel orientation and tunnel thickness. At some locations, the magnitude of these insertion gains is greater than 20dB. This demonstrates that a high degree of inaccuracy exists in any surface vibration-prediction model that includes only one of the two tunnels. © 2012 Springer.

Tsunami wave runup on the clustered islands using boussinesq-type model

This paper describes the implementation of the Boussinesq-type model and extends its application to the tsunami wave runup on the clustered islands (multiple adjacent conical islands), in turn, an extensively validated two-dimensional Boussinesq-type model is employed to examine the interaction between a propagating solitary wave and multiple idealised conical islands, with particular emphasis on a combination effect of two adjustable parameters for spacing interval/diameter ratio between the adjacent conical islands, S/D, and the rotating angle of the structural configuration,θ on maximum soliton runup heights. An extensive parameter study concerning the combination effect of alteringθ and S/D on the maximum soliton runup with the multi-conical islands is subsequently carried out and the distributions of the maximum runup heights on each conical island are obtained and compared for the twin-island cases. The worst case study is performed for each case in respect of the enhancement in the maximum wave runup heights by the multi-conical islands. It is found that the nonlinear wave diffraction, reflection and refraction play a significant role in varying the maximum soliton runup heights on multiconical islands. The comparatively large maximum soliton runups are generally predicted for the merged and bottom mounted clusteredislands. Furthermore, the joints of the clustered-merged islands are demonstrated to suffer the most of the tsunami wave attack. The conical islands that position in the shadow regions behind the surrounding islands are found to withstand relatively less extreme wave impact. Although, these numerical investigations are considerable simplifications of the multi conical islands, they give a critical insight into certain important hydrodynamic characteristics of the interaction between an extreme wave event and a group of clustered conical islands, and thus providing a useful engineering guidance for extreme wave mitigation and coastal development. Copyright © 2012 by the International Society of Offshore and Polar Engineers (ISOPE).

Comparisons between gigabit NRZ, CAP and optical OFDM systems over FEC enhanced POF links using LEDs

Simulations have been performed to compare the link power budget and power dissipation of carrierless amplitude and phase modulation-64 (CAP-64) and 64-quadrature amplitude modulation-orthogonal frequency division multiplexing (64-QAM-OFDM) systems over feedforward error correction (FEC) enhanced plastic optical fibre (POF) links using light emitting diodes (LEDs). It is shown that CAP-64 outperforms 64-QAM-OFDM and supports record high 2.1Gb/s over 50m POF transmission. The CAP-64 and 64-QAM-OFDM links consume similar powers which are 2 (2.5) times of that of NRZ for the single POF link (twin POF links) case. © 2012 IEEE.

Flow field of a model gas turbine swirl burner

The flow field of a lab-scale model gas turbine swirl burner was characterised using particle imaging velocimetry (PIV) at atmospheric condition. The swirl burner consists of an axial swirler, a twin-fluid atomizer and a quartz tube as combustor wall. The main non-reacting swirling air flow without spray was compared to swirl flow with spray under unconfined and enclosed conditions. The introduction of liquid fuel spray changes the flow field of the main swirling air flow at the burner outlet where the radial velocity components are enhanced. Under reacting conditions, the enclosure generates a corner recirculation zone that intensifies the strength of the radial velocity. Comparison of the flow fields with a spray flame using diesel and palm biodiesel shows very similar flow fields. The flow field data can be used as validation target for swirl flame modeling. © (2013) Trans Tech Publications, Switzerland.