Investigation into the role of potentially contaminated feed as a source of the first-detected outbreaks of porcine epidemic diarrhea in Canada

In January 2014, approximately 9 months following the initial detection of porcine epidemic diarrhea (PED) in the USA, the first case of PED was confirmed in a swine herd in south-western Ontario. A follow-up epidemiological investigation carried out on the initial and 10 subsequent Ontario PED cases pointed to feed as a common risk factor. As a result, several lots of feed and spray-dried porcine plasma (SDPP) used as a feed supplement were tested for the presence of PEDV genome by real-time RT-PCR assay. Several of these tested positive, supporting the notion that contaminated feed may have been responsible for the introduction of PEDV into Canada. These findings led us to conduct a bioassay experiment in which three PEDV-positive SDPP samples (from a single lot) and two PEDV-positive feed samples supplemented with this SDPP were used to orally inoculate 3-week-old piglets. Although the feed-inoculated piglets did not show any significant excretion of PEDV, the SDPP-inoculated piglets shed PEDV at a relatively high level for ≥9 days. Despite the fact that the tested PEDV genome positive feed did not result in obvious piglet infection in our bioassay experiment, contaminated feed cannot be ruled out as a likely source of this introduction in the field where many other variables may play a contributing role.

Synthesis and performance of itaconic acid/acrylamide/sodium styrene sulfonate as a self-adapting retarder for oil well cement

This journal is © The Royal Society of Chemistry. A novel self-adapting retarder itaconic acid/acrylamide/sodium styrene sulfonate (IA/AM/SSS, hereinafter referred to as PIAS) was synthesized by free-radical, aqueous-solution polymerization and characterized by FTIR and TG. The optimum reaction conditions of polymerization were obtained from orthogonal experiments (L3³) and subsequent data analysis. According to the evaluation as a retarder, the PIAS made it possible to obtain both a long thickening time and a swift compressive strength development for cement slurry, and therefore the applicable range of bottom hole circulation temperatures to the cement slurry has been widened to 60-180°C. Moreover, the working mechanism of the self-adapting retarder PIAS was found to rely on the change of spatial structure of the molecules to retard the hydration of the cement. This paper also expounds that the delayed coagulation of the cement slurry is attributed to adsorption, chelation and "poisoning" effects of the PIAS molecules on the surface of hydrated particles or ions through XRD and SEM analyses.

Comparação de diferentes etapas de enriquecimento seletivo no isolamento de Salmonella sp. a partir de fezes de suínos de terminação

A detecção de Salmonella sp. é fundamental nos programas de controle de salmonelose. Métodos de detecção mais eficientes permitem uma melhor determinação do nível de infecção dos rebanhos, um melhor entendimento da epidemiologia da infecção por Salmonella sp. e o desenvolvimento de programas de controle do patógeno, que visem a segurança biológica do alimento. Nos métodos convencionais, o enriquecimento seletivo é uma etapa crítica, pois inibe a microbiota competitiva e permite a multiplicação de Salmonella sp. Vários caldos de enriquecimento seletivo têm sido comparados quanto à eficiência na recuperação de Salmonella sp. a partir de alimentos, contudo existem poucos estudos relativos a fezes de suínos. O objetivo deste trabalho foi comparar caldos de enriquecimento seletivo para o isolamento de Salmonella sp. a partir de fezes de suínos. Numa primeira fase, amostras de fezes foram contaminadas artificialmente e os caldos Rappaport-Vassiliadis incubado a 42°C (RV), Tetrationato Müller-Kauffmann a 37°C (TMK37) e 42°C (TMK42), e Selenito Cistina (SC) a 37°C foram testados, em associação com meios sólidos seletivos: Rambach (RA), Xilose Lisina Tergitol 4 (XLT4), e Verde Brilhante Vermelho de Fenol Lactose Sacarose (VB). Na segunda fase os caldos RV, TMK37 e TMK42, semeados nos meios XLT4 e VB, foram testados com amostras naturalmente contaminadas. Na primeira fase o RV, TMK42 e TMK37 foram mais eficientes que o SC. No isolamento de Salmonella sp. em amostras naturalmente contaminadas os caldos TMK42 e RV foram superiores ao TMK37. O desempenho destes influenciou diretamente a capacidade seletiva e indicadora dos meios sólidos seletivos. No presente estudo, a associação TMK42/XLT4 demonstrou ser mais sensível, e a RV/XLT4 mais específica. O ágar VB também é recomendado para aumentar a probabilidade de detecção do patógeno. Desta forma os caldos RV e TMK42 e o ágar XLT4 e o VB foram considerados os mais indicados para a implantação de protocolos de detecção de Salmonella sp. em fezes suínas.

Implante endoscópico no esôfago distal de polimetilmetacrilato para controle do refluxo gastrofágico : estudo experimental em modelo animal

XIXA doença do refluxo gastroesofágico (DRGE) comumente afeta o esôfago e provavelmente é a condição mais prevalente no segmento alto do trato gastrointestinal, acometendo entre 5 e 45% da população ocidental. A terapêutica atual para essa doença além de medidas gerais e dietéticas, inclui tratamento farmacológico e/ou cirurgia. Ambos podem ser eficazes, mas apresentam elevado custo financeiro. O tratamento com fármacos pode apresentar baixa aderência medicamentosa e a cirurgia tem baixa, mas não desprezível, morbidade e mortalidade. Idealmente o tratamento da DRGE deveria ser eficaz, com baixo risco e com baixo custo. Objetivos: 1. Desenvolver um modelo experimental em suínos para o estudo do Refluxo Gastroesofágico através da Pressão e do Volume de Vazão Gástricos; 2. Avaliar a eficácia do implante endoscópico de PMMA ao nível do Esfíncter Esofágico Inferior (EEI) para aumentar a Pressão de Vazão Gástrica, o Volume de Vazão Gástrico e a Pressão Basal do EEI; 3. Descrever as reações histológicas associadas ao implante de PMMA. Material e Métodos: Suínos da raça Large White, do sexo feminino com 8 semanas de vida foram estudados no experimento. Foi realizada manometria do esfíncter esofágico inferior com registro da pressão basal com cateter de perfusão com água e técnica de retirada lenta. Calculou-se, também, a extensão do EEI. Após, gastrostomia era realizada com colocação intragástrica da extremidade distal de uma sonda de Foley com três vias e um cateter de pHmetria esofágica introduzido via oral com o sensor distal posicionado 5 cm acima do bordo superior de esfíncter esofágico inferior. Iniciava-se, XXentão, a infusão contínua no estômago de uma solução de HCl a 0,02N com medida e registro simultâneos da Pressão e do Volume de Vazão Gástricos e do pH esofágico. Definiu-se a Pressão de Vazão Gástrica (PVG) e o Volume de Vazão Gástrico quando houve brusca e sustentada acidificação do esôfago distal (pH<3). Após, introduzia-se um tubo metálico (Tubo Introdutor ou TI) via oral e, em seguida, o endoscópio, seguindo ambos até o esôfago distal. Cateter de nylon com agulha calibre 16 era introduzido pelo tubo introdutor e o PMMA implantado na área correspondente ao EEI com uma pistola dosadora volumétrica que permitia a injeção de volumes prédeterminados em 3 ou 4 pontos da submucosa (total por ponto = 0,73 ml de PMMA). As medidas de PVG, VVG e pressão basal do EEI foram repetidas após 28 dias, sacrificando-se os animais e removendo-se esôfago médio e distal, junção esofagogástrica, fundo e corpo gástricos para estudo histológico. Previamente ao experimento, três projetos pilotos foram desenvolvidos. O primeiro designado como “Projeto Piloto: Refluxo Gastroesofágico por pHmetria de 24H” (RGE 24H) buscou a via de acesso transnasal para registro de pHmetria por 24 horas. No segundo, designado “Projeto Piloto: Esofagostomia”, para confirmação de refluxo gastroesofágico espontâneo em suínos da raça Large White, utilizou-se anestesia com associação de tiletamina 125 mg e zolazepam 125 mg em combinação com um sedativo, a xilazina a 2% . A pHmetria foi mantida por 24 horas. Os dados descritos por Kadirkamanathan et al. não foram reproduzidos no nosso laboratório. Optou-se então pela realização de um terceiro projeto, “Projeto Piloto: Gastrostomia” para induzir refluxo gastroesofágico através de um modelo experimental e testar a reprodutibilidade da Pressão de Vazão Gástrica. Obteve-se sucesso. Resultados: Trinta e sete animais foram estudados em 60 intervenções no Laboratório de motilidade experimental. O projeto piloto “RGE:24h” foi abandonado após perda de 5 animais pela anestesia com halotano e, solucionada esta questão, a sistemática infecção do tecido celular subcutâneo nasal, dificultando a manutenção do cateter de phmetria em outros 5 animais. No “Projeto Piloto: Esofagostomia”, em cinco animais estudados (cada animal em duas ocasiões diferentes) não se reproduziram os achados de refluxo espontâneo. No terceiro projeto “Projeto Piloto: Gastrostomia” quatro animais foram estudados em dois momentos diferentes obtendo-se sucesso e reprodutibilidade XXIdos dados. Criado o modelo experimental, quatorze suínos foram submetidos ao experimento com implante endoscópico de PMMA com os seguintes resultados: A média dos pesos com 8 semanas de idade foi 14,98 ± 2,43 e 28 dias após o implante, 20,26 ± 3,68. O ganho ponderal foi considerado normal para a espécie. A Pressão de Vazão Gástrica média no dia 1 foi 8,08 mmHg e no dia 28, 10,69mmHg (Teste t de Student: t = 2,72 gl = 13 p = 0,017). Os Volumes de Vazão Gástricos médios foram: 392,86 ml para o dia 1 e 996,71 ml no dia 28 (teste t de Student: t = 11,66 gl = 13 p< 0,001). A Pressão Basal do EEI e o comprimento do esfíncter, não apresentaram diferenças estatisticamente significativas. PMMA foi identificado como depósitos de grandes vacúolos no tecido intersticial ao exame histológico da junção esofagogástrica associado a histiócitos, plasmócitos e presença de células gigantes tipo Langhans indicando reação tecidual de corpo estranho em todos os animais. Fibrose e macrófagos com vacúolos intracelulares estiveram presentes em menor freqüência. Conclusões: 1. O modelo experimental, em suínos, desenvolvido viabilizou o estudo do Refluxo Gastroesofágico através da Pressão de Vazão Gástrica e Volume de Vazão Gástrico; 2. O implante de PMMA, no presente estudo, aumentou a Pressão de Vazão e o Volume de Vazão Gástricos, mas não a Pressão Basal do EEI, nem tampouco aumentou o seu comprimento; 3. Depósito de PMMA implantado e evidência de processo inflamatório crônico e reação tecidual de corpo estranho foi encontrada no local do implante de PMMA. Macrófagos com vacúolos intracelulares e fibrose foram encontrados com menos freqüência.

Isolamento e caracterização de Salmonella sp. em suínos ao abate e em cortes de pernil

A Salmonella sp. é uma das principais causas de doenças transmitidas por alimentos, principalmente de origem animal. Os suínos podem ser portadores assintomáticos de Salmonella sp. e, nessa condição, serem levados ao abate. Desta forma, a entrada de Salmonella sp. na cadeia de produção é uma preocupação para a indústria. Sabendo-se da importância deste microrganismo, pelo seu impacto na indústria e na saúde pública, este trabalho teve como objetivo determinar a prevalêncía de Salmonella sp. em suínos levados ao abate em um frigorífico sob inspeção federal no Rio Grande do Sul, e correlacionar com a contaminação de cortes de pernil. Para tanto, 64 amostras de conteúdo intestinal e 121 amostras de cortes de pernil coletadas em 4 visitas, foram submetidas ao isolamento e identificação de Salmonella sp. As amostras de Salmonella sp. foram avaliadas quanto a resistência a 14 antimicrobianos, através da técnica de difusão em ágar. Salmonella sp. foi isolada de 46,87% das amostras de conteúdo intestinal e de 49,59% dos cortes de pernil. Foi encontrado grande número de sorovares, sendo os mais prevalentes Panama e Bredeney. Das amostras isoladas, 60,8% apresentaram perfil de multiresistência, sendo os maiores índices de resistência a sulfonamida, ácido nalidíxico e tetraciclina. Utilizando o perfil de resistência a antimicrobianos de amostras de um mesmo sorovar forma comparadas quanto a sua similaridade e agrupadas em dendrogramas, observou-se grande diversidade nas linhagens isoladas. Os resultados demonstraram que a entrada de animais no frigorífico excretando Salmonella sp., pode contribuir para a contaminação do produto final. A diversidade de sorovares e linhagens pode representar que são várias as fontes de contaminação, tanto dos animais quanto do produto final.

Creating buyer-supplier commitment in food supply chains at the base of the pyramid

Esta pesquisa analisa o papel dos aspectos relacionais tais como confiança, comprometimento, interdependência e uso de poder âmbito das estratégias de negócios inclusivos que envolvem pequenos agricultores nas cadeias de valor de multinacionais dos agronegócios no Brasil. Os negócios inclusivos de abastecimento direto por empresas com pequenos agricultores em países em desenvolvimento têm sido reconhecidos como uma abordagem economicamente viavél e promissora para criar impacto social e melhorar as condições de vida de produtores rurais da "base da pirâmide", ao mesmo tempo permitindo que as empresas reforçar as suas posições nos mercados locais e adquirir matérias primas de qualidade a custos mais baixos. Estudos sobre este tema focam amplamente sobre as vantagens comerciais e competitivas que as empresas derivam do abastecimento direito com pequenos fornecedores, apresentando modelos de cadeia de valor customizados e ajustados estratégias globais de negócios, no entanto ainda há pouco conhecimento teoricamente fundamentado sobre os desafios organizacionais e relacionais da relação entre o comprador multinacional e o fornecedor de baixa renda. Além disso, pouco foco tem-se prestado sobre como assimetrias entre multinacionais e produtores de baixa renda, em questão de poder, dependência e de valores pode afetar a evolução dessas relações de negócios. O objetivo do estudo foi descrever os fatores que permitem a esses parceiros assimétricos de construir relacionamentos comerciais de longo prazo e mutuamente benéficos. A metodologia da teoria fundamentada foi usada e foi particularmente adequada para examinar as relações entre comprador e fornecedor e para recolher experiências de campo em três setores principais dominados pela agricultura familiar no Brasil, ou seja laticínios, avi-suinocultura e produção hortícola. Os principais conceitos teóricos da área de Relationship Marketing foram usados para apoiar os resultados da pesquisa de campo. A principal conclusão desta pesquisa é a importância de ir além da construção de confiança na estratégia de gestão do relacionamento entre comprador e fornecedor e de criar parcerias diádicas baseadas na interdependência mútua, a fim de reduzir as assimetrias e melhorar o comprometimento entre a empresa e o pequeno agricultor.

Avaliação da ecotoxicidade de percolados em áreas de disposição de resíduos na região metropolitana de Natal/RN

Leachates are effluent produced by decomposition of solid waste, they have complex composition and can be highly toxic. Therefore such percolated liquid should be collected and treated properly to avoid environmental contamination of soil and of water bodies. The objective of this study was to evaluate the toxicity through ecotoxicological tests with Ceriodaphnia dubia (Cladocera - Crustacea) of percolated liquids generated in two different systems of municipal solid waste (MSW) disposal in the city of Natal/ RN: A Sanitary Landfill in the Metropolitan Region of Natal/ RN, and in a dump off area. Furthermore, it was evaluated the possible contamination of the underground water of the dump off area. Two monthly samples were taken at four points between the months of May/2009 and January/2010. The Point "A" corresponds to the end of the pond leachate treatment in ASRMN; The Point "B" corresponds to a containment pond at the dump. The Point "C" is an area near one of the cells of the dump off area where the leachate outcrops; The Point "D" stands for an underground water well at the area. The last point, called "E" was sampled only once and corresponds to the slurry produced by temporary accumulation of solid waste in the open area of the dump. The ecotoxicological tests, acute and chronic, followed the ABNT 13373/2005 rules, with some modifications. The samples were characterized by measuring the pH number, the dissolved oxygen (DO), the salinity, BOD5, COD, Cd, Cu, Pb, Cr, Fe, Mg, Ni, and Zn. At Point A, the average number of EC50-48h ranged between 1.0% and 2.77% (v/v), showing a high toxicity of the leachate to C.dubia in all months. To this point, positive correlations were found between the EC50- 48 with precipitation. Negative correlations were found between the EC50- 48h with salinity. At point B there was no response of the acute exposure of organisms to the test samples. At point C the EC50-48h ranged from 17.68% to 35.36% in just two months of the five ones analyzed, not correlated meaning. Point D, the EC50-48h level ranged between 12.31% and 71.27%, showed a negative correlation with, only, precipitation. Although it was observed toxicity of underground water in the Landfill Area, there was no evidence of water contamination by leachate, however, due to the toxic character of this water, additional tests should be conducted to confirm the quality of water that is used for human supply. At point E there was no acute toxicity. These results support the dangers of inappropriate disposal of MSW to water bodies due to the high toxicity of the leachate produced highlighting the necessity of places of safe confinement and a treatment system more effective to it

Adição de superplastificante e anti-segregante à base de CMC em pastas de cimento para Poços de Petróleo

Oil well cementing materials consist of slurries of Special class Portland cement dispersed in water. Admixtures can be used to provide the necessary fluidity, so the material can be efficiently pumped down as well as penetrate porous rocks with controlled filter loss. Construction admixtures can be used to modify the properties of oil well cements provided they can withstand and hold their properties at the higher than ambient temperatures usually encountered in oil fields. In civil construction, superplasticizer play the role of dispersants that reduce the facto r of water cement improve mechanical properties and fluidity of the cement, whereas anti-segregation agents improve the workability of the slurry. In the present study, oil well cement slurries were produced adding both a dispersant and an anti-segregation agent conventionally used in Portland CPII-Z-32 RS cement aiming at materials for primary cementing and squeeze operations. Three basic aspects were evaluated: fluidity, filter loss and the synergetic effect of the admixtures at two temperatures, i.e., 27°C and 56°C, following API RP 10B practical recommendations. The slurries were prepared using admixture concentrations varying from 2.60 Kgf/m3 (0.02 gallft3) to 5.82 Kgf/m3 (0.045 galJft3) BWOC. The density of the slurries was set to 1.89 g/cm3 (15.8 Ib/gal). 0.30 to 0.60% BWOC of a CMC-based anti-segregation agent was added to the cement to control the filter loss. The results showed that the addition of anti-segregation at concentrations above 0.55% by weight of cement resulted in the increased viscosity of the folders in temperatures evaluated. The increasing the temperature of the tests led to a reduction in the performance of anti-segregation. At concentrations of 5.20 kgf/m3 (0,040 gallft3) and 5.82 Kgf/m3 (0,045 gal/ft 3) observed a better performance of the properties evaluated in the proposed system. At low temperature was observed instability in the readings of rheology for all concentrations of anti-segregation. Contents that increasing the concentration of anti¬-segregation is limited concentrations greater than 0.55 % BWOC of the CMC in temperature analyzed. The use of the system with CMC promoted a good performance against the properties evaluated. The principal function of anti¬-segregation was optimized with increasing concentration of superplasticizer, at temperatures above the 2rC. The study of the behaviour of systemic additives, resulting in slurries of cement, which can be optimized face studies of other intrinsic properties in oil fields

Influência da vermiculita expandida na resistência à compressão e reologia de pastas cimentantes de poços de petróleo

Several problems related to the loss of hydraulic seal in oilwells, causing gas migration and/or contamination of the production zone by water, have been reported. The loss of the hydraulic seal is a consequence of cracks which can be occasioned either by the invasion of gas during the wait on cement or by the expansion of the casing causing the fracture of the cement sheath. In case of the pressure of the formation is higher than the pressure in the annulus, gas can migrate into the slurry and form microannulus, which are channels where gas migrates after the cement is set. Cracks can be also occasioned by the fracture of the cement sheath when it does not withstand the thermal and dynamic loads. In reservoirs where the oil is heavy, steam water injection operation is required in order to get the oil flowing. This operation increases the temperature of the casing, and then it expands and causes the fracture of the cement sheath in the annulus. When the failures on the cement are detected, remedial cementing is required, which raise costs caused by the interventions. Once the use of cement in the construction civil sector is older than its use in the petroleum sector, it is common to bring technologies and solutions from the civil construction and apply them on the petroleum area. In this context, vermiculite, a mineral-clay widely encountered in Brazil, has been used, on its exfoliated form, in the civil construction, especially on the manufacture of lights and fireproof concretes with excellent thermal and acoustical properties. It has already been reported in scientific journals, studies of the addition of exfoliated vermiculite in Portland cements revealing good properties related to oilwell cementing operations. Thus, this study aimed to study the rheological behavior, thickening time, stability and compressive strength of the slurries made of Portland cement and exfoliated vermiculite in 5 different compositions, at room temperature and heated. The results showed that the compressive strength decreased with the addition of exfoliated vermiculite, however the values are still allowed for oiwell cementing operations. The thickening time of the slurry with no exfoliated vermiculite was 120 min and the thickening time of the slurry with 12 % of exfoliated vermiculite was 98 min. The stability and the rheological behavior of the slurries revealed that the exfoliated vermiculite absorbed water and therefore increased the viscosity of the slurries, even though increasing the factor cement-water. The stability experiment carried out at 133 ºF showed that, there was neither sedimentation nor reduction of the volume of the cement for the slurry with 12 % of exfoliated vermiculite. Thus, the addition of exfoliated vermiculite accelerates the set time of the cement and gives it a small shrinkage during the wait on cement, which are important to prevent gas migration

Otimização e análise mecânica de pastas geopoliméricas para uso em poços sujeitos à injeção cíclica de vapor

Oil wells subjected to cyclic steam injection present important challenges for the development of well cementing systems, mainly due to tensile stresses caused by thermal gradients during its useful life. Cement sheath failures in wells using conventional high compressive strength systems lead to the use of cement systems that are more flexible and/or ductile, with emphasis on Portland cement systems with latex addition. Recent research efforts have presented geopolymeric systems as alternatives. These cementing systems are based on alkaline activation of amorphous aluminosilicates such as metakaolin or fly ash and display advantageous properties such as high compressive strength, fast setting and thermal stability. Basic geopolymeric formulations can be found in the literature, which meet basic oil industry specifications such as rheology, compressive strength and thickening time. In this work, new geopolymeric formulations were developed, based on metakaolin, potassium silicate, potassium hydroxide, silica fume and mineral fiber, using the state of the art in chemical composition, mixture modeling and additivation to optimize the most relevant properties for oil well cementing. Starting from molar ratios considered ideal in the literature (SiO2/Al2O3 = 3.8 e K2O/Al2O3 = 1.0), a study of dry mixtures was performed,based on the compressive packing model, resulting in an optimal volume of 6% for the added solid material. This material (silica fume and mineral fiber) works both as an additional silica source (in the case of silica fume) and as mechanical reinforcement, especially in the case of mineral fiber, which incremented the tensile strength. The first triaxial mechanical study of this class of materials was performed. For comparison, a mechanical study of conventional latex-based cementing systems was also carried out. Regardless of differences in the failure mode (brittle for geopolymers, ductile for latex-based systems), the superior uniaxial compressive strength (37 MPa for the geopolymeric slurry P5 versus 18 MPa for the conventional slurry P2), similar triaxial behavior (friction angle 21° for P5 and P2) and lower stifness (in the elastic region 5.1 GPa for P5 versus 6.8 GPa for P2) of the geopolymeric systems allowed them to withstand a similar amount of mechanical energy (155 kJ/m3 for P5 versus 208 kJ/m3 for P2), noting that geopolymers work in the elastic regime, without the microcracking present in the case of latex-based systems. Therefore, the geopolymers studied on this work must be designed for application in the elastic region to avoid brittle failure. Finally, the tensile strength of geopolymers is originally poor (1.3 MPa for the geopolymeric slurry P3) due to its brittle structure. However, after additivation with mineral fiber, the tensile strength became equivalent to that of latex-based systems (2.3 MPa for P5 and 2.1 MPa for P2). The technical viability of conventional and proposed formulations was evaluated for the whole well life, including stresses due to cyclic steam injection. This analysis was performed using finite element-based simulation software. It was verified that conventional slurries are viable up to 204ºF (400ºC) and geopolymeric slurries are viable above 500ºF (260ºC)

Formulação de pastas cimentícias com adição de suspensões de quitosana para cimentação de poços de petróleo

Primary cementing is one of the main operations in well drilling responsible for the mechanical stability and zonal isolation during the production of oil. However, the cement sheath is constantly under mechanical stresses and temperature variations caused by the recovery of heavy oil. In order to minimize fracture and wear of the cement sheath, new admixtures are developed to improve the properties of Portland cement slurries and avoid environmental contamination caused by leaking gas and oil. Polymers with the ability to form polymeric films are candidates to improve the properties of hardened cement slurries, especially their fracture energy. The present study aimed at evaluating the effect of the addition of a chitosan suspension on cement slurries in order to improve the properties of the cement and increase its performance on heavy oil recovery. Chitosan was dissolved in acetic ac id (0.25 M and 2 M) and added to the formulation of the slurries in different concentrations. SEM analyses confirmed the formation of polymeric films in the cementitious matrix. Strength tests showed higher fracture energy compared to slurries without the addition of chitosan. The formation of the polymeric films also reduced the permeability of the slurry. Therefore, chitosan suspensions can be potentially used as cementing admixtures for heavy oil well applications

Influência da adição de cálcio nas propriedades de pastas geopoliméricas destinadas a cimentação de poços de petróleo

Nowadays, the search for new technologies that are able to follow the upcoming challenges in oil industry is a constant. Always trying properties improvements of the used materials, looking for the best performance and greater life time. Besides the search for technologies that show an improvement of performance, the search for materials environmentally correct along the whole production process. In Oil well cementing, this search for new technologies passes through the development of slurry systems that support these requests and that are also environmentally friendly. In this context, the use of geopolymer slurries is a great alternative route to cementing oil wells. Besides having good properties, comparable to Portland cement slurries, this alternative material releases much less CO2 gas in the production of their root materials when compared the production of Portland cement, which releases tons of CO2. In order to improve the properties of geopolymer slurries has been added Calcium Oxide, as observed in other studies that slurries where the Calcium is present the values of compressive strength is greater. The addition has been realized based in the CaO/SiO2 molar ratio of 0.05, 0.10 and 0.15. Have been performed compressive strength tests, thickening time, rheology and fliud loss control test of the slurries, following NBR 9831, as well as the physical chemical characterization of XRD, SEM and TG. Has been observed in most of the tests the slurries follow a tendency until the ratio of 0.10, which inverses in the ratio 0.15. This behavior can be explained by two phenomena that occur simultaneously, the first one is the break of the polymer chains and a consequent increase in molucules mobility, which prevails until the ratio of 0.1, and the second is possible approach of the chains due to the capacity of the calcium ions stabilize the charges of two different aluminum. There is only one linearity in the mechanical behavior that can be attributed to the appereance of the C-S-H phase. Based on this, it is concluded that the phenomenon of breaking the polymer chains predominates until the ratio of 0.1, causing an increase of the filtrate volume, lower rheological parameters and increasing thickening time. From the ratio of 0.15 the approach of the chains predominates, and the behavior is reversed

Efeito da incorporação de diatomita na estabilidade e permeabilidade de compósitos cimentíceos espumados aplicados a poços de petróleo

Lightweight oilwell cement slurries have been recently studied as a mean to improve zonal isolation and sheath-porous formation adherence. Foamed slurries consisting of Portland cement and air-entraining admixtures have become an interesting option for this application. The loss in hydrostatic pressure as a consequence of cement hydration results in the expansion of the air bubbles entrapped in the cement matrix, thus improving the sheath-porous formation contact. Consequently, slurries are able to better retain their water to complete the hydration process. The main objective of the present study was to evaluate the effect of the addition of an air-entraining admixture on the density, stability and permeability of composite slurries containing Portland cement and diatomite as light mineral load. Successful formulations are potential cementing materials for low fracture gradient oilwells. The experimental procedures used for slurry preparation and characterization were based on the American Petroleum Institute and ABNT guidelines Slurries containing a pre-established concentration of the air-entraining admixture and different contents of diatomite were prepared aiming at final densities of 13 to 15 lb/gal. The results revealed that the reduction of 15 to 25% of the density of the slurries did not significantly affect their strength. The addition of both diatomite and the air-entraining admixture increased the viscosity of the slurry providing better air-bubble retention in the volume of the slurry. Stable slurries depicted bottom to top density variation of less than 1.0 lb/gal and length reduction of the stability sample of 5.86 mm. Finally, permeability coefficient values between 0.617 and 0.406 mD were obtained. Therefore, lightweight oilwell cement slurries depicting a satisfactory set of physicochemical and mechanical properties can be formulated using a combination of diatomite and air-entraining admixtures for low fracture gradient oilwells

Adição de resíduo cerâmico em pastas geopoliméricas para cimentação de poços de petróleo

The development of activities the of oil and gas sector have promoted the search for suitable materials for cementing oil wells. In the state of the Rio Grande do Norte, the integrity of the cement sheath tends to be impaired during steam injection, a procedure necessary to increase oil recovery in reservoirs with low-viscosity oil. The geopolymer is a material that can be used as alternative cement, since it has been used in the production of fire-resistant components, building structures, and for the control of toxic or radioactive residues. Geopolymers result from condensation polymer alkali aluminosilicates and silicates resulting three-dimensional polymeric structures. They are produced in a manner different from that of Portland cement, which is made an activating solution that is mixed with geopolymer precursor. Among the few works studied allowed us to conclude that the pastes prepared with metakaolin as precursor showed better performance of its properties. Several studies show the addition of waste clay as a means of reducing cost and improving end of the folder properties. On this basis, the goal is to study the influence of the addition of ceramic waste in geopolymer paste. To develop the study of rheology tests were carried out, filtered, thickening time, compressive strength, free water, specific gravity and permeability, according to the American Pretoleum Institute (API). The results for all formulations studied show that the folders have high mechanical strength to a light paste; low filtrate volume, absence of free water, very low permeability, slurry, consistent with a light paste, and thickening time low that can be corrected with the use of a retardant handle. For morphological characterization, microstructural, physical, chemical and thermal tests were carried out by XRD, MEV, DTA, TG, FTIR. In the trial of XRD, it was found that geopolymer is an amorphous material, with a peak of crystalline kaolinite. In tests of TG / DTA, revealed the presence of a significant event, which represents the mass loss related to water, and also observed the reduction of weight loss by increasing the concentration of ceramic waste. In the trial of MEV, we found a uniform matrix without the presence of other phases. In the trial of FT-IR, we observed the presence of the band related to water. From all results it was determined that the optimum concentration range of use is between 2.5 and 5% of waste ceramic

Avaliação da adição de Nanosílica e silicato de sódio em pastas de cimento para poços de petróleo com baixo gradiente de fratura

The oil wells cementing is a critical step during the phase of well drilling, because problems during the operation of slurry pumping and an incomplete filling of the annular space between the metal casing and the formation can cause the slurry loss. Therefore, the slurry adopted in primary cementing an oil well must be properly dosed so that these problems are avoided during its pumping. When you drill a well in a weak rock formation requires even more careful, because should be a limit of hydrostatic pressure exerted during cementation, that does not occur rock collapse. With the objective of performing the cementing of a well whose formation is weak or unconsolidated are employed lighter slurries. Thus, this study used slurries with sodium silicate and nano silica in concentrations of 0,1; 0,4; 0,7 e 1,0 gpc, in which the slurries with nano silica showed the rheological parameters higher concentrations of up to 0.7 gpc and for concentration of 1.0 the slurry with sodium silicate obtained the highest values, remaining above the limits for application in fields, mainly wells with low fracture gradient, because a significant increase in viscosity may result in an increase in pressure pumping in operations of secondary cementations. Furthermore, there was no decrease in strength with increasing concentration of additive. Then, it is possible use of these additives to formulate Lighter slurry