A novel high voltage pulsed power supply based on low voltage switch-capacitor units

This paper presents a high voltage pulsed power system based on low voltage switch-capacitor units connected to a current source for several applications such as plasma systems. A buck-boost converter topology is used to utilize the current source and a series of low voltage switch-capacitor units is connected to the current source in order to provide high voltage with high voltage stress (dv/dt) as demanded by loads. This pulsed power converter is flexible in terms of energy control, in that the stored energy in the current source can be adjusted by changing the current magnitude to significantly improve the efficiency of various systems with different requirements. Output voltage magnitude and stress (dv/dt) can be controlled by a proper selection of components and control algorithm to turn on and off switching devices.

A new predictive current control technique for multilevel converters

Multilevel inverters provide an attractive solution for power electronics when both reduced harmonic contents and high voltages are required. In this paper, a novel predictive current control technique is proposed for a three-phase multilevel inverter, which controls the capacitors voltages and load currents with low switching losses. The advantage of this contribution is that the technique can be applied to more voltage levels without significantly changing the control circuit. The three-phase three-level inverter with a pure inductive load has been implemented to track reference currents using analogue circuits and programmable logic device.

Online estimation of distorted power system signal parameters

An algorithm based on the concept of Kalman filtering is proposed in this paper for the estimation of power system signal attributes, like amplitude, frequency and phase angle. This technique can be used in protection relays, digital AVRs, DSTATCOMs, FACTS and other power electronics applications. Furthermore this algorithm is particularly suitable for the integration of distributed generation sources to power grids when fast and accurate detection of small variations of signal attributes are needed. Practical considerations such as the effect of noise, higher order harmonics, and computational issues of the algorithm are considered and tested in the paper. Several computer simulations are presented to highlight the usefulness of the proposed approach. Simulation results show that the proposed technique can simultaneously estimate the signal attributes, even if it is highly distorted due to the presence of non-linear loads and noise.

Analysis of phasor measurement method in tracking the power frequency of distorted signals

This paper presents an analysis of phasor measurement method for tracking the fundamental power frequency to show if it has the performance necessary to cope with the requirements of power system protection and control. In this regard, several computer simulations presenting the conditions of a typical power system signal especially those highly distorted by harmonics, noise and offset, are provided to evaluate the response of the Phasor Measurement (PM) technique. A new method, which can shorten the delay of estimation, has also been proposed for the PM method to work for signals free of even-order harmonics.

Multi-output DC-DC converters based on diode-clamped converters configuration : topology and control strategy

This paper presents a new DC-DC Multi-Output Boost (MOB) converter which can share its total output between different series of output voltages for low and high power applications. This configuration can be utilised instead of several single output power supplies. This is a compatible topology for a diode-clamed inverter in the grid connection systems, where boosting low rectified output-voltage and series DC link capacitors is required. To verify the proposed topology, steady state and dynamic analysis of a MOB converter are examined. A simple control strategy has been proposed to demonstrate the performance of the proposed topology for a double-output boost converter. The topology and its control strategy can easily be extended to offer multiple outputs. Simulation and experimental results are presented to show the validity of the control strategy for the proposed converter.

Load sharing and power quality enhanced operation of a distributed microgrid

This paper describes control methods for proper load sharing between parallel converters connected in a microgrid and supplied by distributed generators (DGs). It is assumed that the microgrid spans a large area and it supplies loads in both in grid connected and islanded modes. A control strategy is proposed to improve power quality and proper load sharing in both islanded and grid connected modes. It is assumed that each of the DGs has a local load connected to it which can be unbalanced and/or nonlinear. The DGs compensate the effects of unbalance and nonlinearity of the local loads. Common loads are also connected to the microgrid, which are supplied by the utility grid under normal conditions. However during islanding, each of the DGs supplies its local load and shares the common load through droop characteristics. Both impedance and motor loads are considered to verify the system response. The efficacy of the controller has been validated through simulation for various operating conditions using PSCAD. It has been found through simulation that the total Harmonic Distortion (THD) of the of the microgrid voltage is about 10% and the negative and zero sequence component are around 20% of the positive sequence component before compensation. After compensation, the THD remain below 0.5%, whereas, negative and zero sequence components of the voltages remain below 0.02% of the positive sequence component.

Young Children and the Environment : Early Learning for Sustainability

This world-first text book on early childhood edcuation for sustainabilty tackles one of the biggest contemporary issues of our times - the changing environmment - and demonstrates how early education can contribute to sustainable living. An essential text for students in early childhood teacher education and a practcial resource for child care practitioners and primary school teachers, it is designed to promote edcuation for sustainabilty from birth to eight years. the text refers to national and international initiatives such as 'sustainable Schools', 'Child Friendly Cities' and 'Health Promoting Schools' and explores their existing and potential links with early childhood education. Groundbreaking content draws on recent literature in the areas of organisational, educational and cultural chnage, and environmental sustainabilty. Specific chapters explore ethical challenges and the use of ICT to advance learning. Case studies and vignettes exemplify leadership in practice and 'provocations' are integrated throughout to inspire new ways of thinking about the environment, the wider world, young children and the transformative power of early edcuation.

Multi-output buck-boost converter with enhanced dynamic response to load and input voltage changes

This paper presents a new multi-output DC/DC converter topology that has step-up and step-down conversion capabilities. In this topology, several output voltages can be generated which can be used in different applications such as multilevel converters with diode-clamped topology or power supplies with several voltage levels. Steady state and dynamic equations of the proposed multi-output converter have been developed, that can be used for steady state and transient analysis. Two control techniques have been proposed for this topology based on constant and dynamic hysteresis band height control to address different applications. Simulations have been performed for different operating modes and load conditions to verify the proposed topology and its control technique. Additionally, a laboratory prototype is designed and implemented to verify the simulation results.

Future-proofing : the academic library’s role in e-research support

Purpose – The paper describes a project created to enhance e-research support activities within an Australian university, based on environmental scanning of e-research activities and funding both nationally and internationally. Participation by the university library is also described.----- Design/methodology/approach – The paper uses a case study that describes the stages of a project undertaken to develop an academic library’s capacity to offer e-research support to its institution’s research community.----- Findings – While the outcomes of the project have been successfully achieved, the work needs to be continued and eventually mainstreamed as core business in order to keep pace with developments in e-research. The continual skilling up of the university’s researchers and research support staff in e-research activities is imperative in reaching the goal of becoming a highly competitive research institution.----- Research limitations/implications – Although a single case study, the work has been contextualised within the national research agenda.----- Practical implications – The paper provides a project model that can adapted within an academic library without external or specialist skills. It is also scalable and can be applied at a divisional or broader level.----- Originality/value – The paper highlights the drivers for research investment in Australia and provides a model of how building e-research support activities can leverage this investment and contribute towards successful research activity.

Why adopt now? Multiple case studies and survey studies comparing small, medium and large firms

While a number of factors have been highlighted in the innovation adoption literature, little is known about the key triggers of innovation adoption across differently-sized firms. This study compares case studies of small, medium and large manufacturing firms who recently decided to adopt a process innovation. We also employ organizational surveys from 134 firms investigating the factors which influence innovation adoption. The quantitative results support the qualitative findings that the external pressures are a trigger among small to medium firms, while the larger firm’s adoption was associated with internal causes.

Building eResearch Services, Capabilities and Capacity

The Queensland University of Technology (QUT) is known for several flagship eResearch centres. It also has a number of mature, centralised research support services that address a several of areas of eResearch. The university has openly stated its aspiration to be an institution with a strongly embedded eResearch capability and to this end it has expressed the desire to establish a university-wide eResearch support service. However, articulating this desire is much easier than realising it. During 2008 QUT undertook a major review into eResearch that made recommendations on the development of university-wide eResearch support service and the building of eResearch capabilities and capacity throughout the university. The results of this review were reported last year at this conference. In 2009, QUT is progressing a second, follow-on project – Building eResearch Support Capability and Capacity. It has been designed to build upon existing strengths in HPC, repositories, data management, and the delivery of integrated skills for eresearch. The purpose of this presentation is to give an update on QUT’s journey, one year on from its first major report into eResearch. It will outline how the university is approaching this challenge, the current work being carried out and the strategies being employed. We will also discuss the lessons learned.

Students’ conceptual knowledge about workplace pedagogies and applications to learning in the workplace

The development of effective workplace pedagogies is integral to work-integrated and work-based learning. The workplace pedagogies that facilitate and support learning include: activities in which individuals engage such as daily work practices, questioning; observing, and listening; interactions with more experienced workers through coaching and modelling; and referencing documented procedures. Each of these dimensions is significant in enhancing processes of workplace learning. Learning can be optimised when these pedagogies are appropriately embedded in the context of and process of participating in normal work activities. Yet learners need to understand the nature of these pedagogies, and how and for what purposes to use these to achieve a range of learning outcomes. This is because it is the worker-learners who play the key roles in the process and outcomes of learning through work. A pilot study was conducted on students’ conceptions of how each of these dimensions of workplace pedagogy help their learning, by providing examples of learning from these sources; and stating their preferences for learning in the workplace. A sample of seventeen students, enrolled in the second year of a Diploma in Nursing course at a Technical and Further Education institution, participated in a survey intended to capture these conceptions and the importance attached to each of them. The findings indicate that these students have basic understanding of how each of seven workplace pedagogic practices can contribute to their learning. They reported relying mostly on daily practices, observing and listening to others, modelling, coaching, and other workers. Their selection of these contributions emphasise significant opportunities for guided learning by others, yet suggest fewer student-initiated interactions, less intensity in interactions, and likelihood that learning is more passive. The data also suggests that these students rely mostly on using academic learning skill, and limited workplace learning skills. It is proposed, therefore, that the knowledge and understandings about workplace learning and pedagogies might be best embedded in the full curriculum and not become add-on shortly before students go on work placement. This approach will allow students to appreciate the significance and use of workplace pedagogies for learning.

ePortfolio use by university students in Australia: Informing excellence in policy and practice

In mid 2007, the Australian Learning and Teaching Council (ALTC), formerly the Carrick Institute for Learning and Teaching in Higher Education, commissioned an intensive research project to examine the use of ePortfolios by university students in Australia. The project was awarded to a consortium of four universities: Queensland University of Technology as lead institution, The University of Melbourne, University of New England and University of Wollongong.---------- The overarching aim of the research project, which was given the working title of the Australian ePortfolio Project, was to examine the current levels of ePortfolio practice in Australian higher education. The principal project goals sought to provide an overview and analysis of the national and international ePortfolio contexts, document the types of ePortfolios used in Australian higher education, examine the relationship with the National Diploma Supplement project funded by the Federal government, identify any significant issues relating to ePortfolio implementation, and offer guidance about future opportunities for ePortfolio development. The research findings revealed that there was a high level of interest in the use of ePortfolios in the context of higher education, particularly in terms of the potential to help students become reflective learners who are conscious of their personal and professional strengths and weaknesses, as well as to make their existing and developing skills more explicit. There were some good examples of early adoption in different institutions, although this tended to be distributed across the sector. The greatest use of ePortfolios was recorded in coursework programs, rather than in research programs, with implementation generally reflecting subject-specific or program-based activity, as opposed to faculty- or university-wide activity. Accordingly, responsibility for implementation frequently rested with the individual teaching unit, although an alternative centralised model of coordination by ICT services, careers and employment or teaching and learning support was beginning to emerge. The project report concludes with a series of recommendations to guide the process, drawing on the need for open dialogue and effective collaboration between the stakeholders across the range of contexts: government policy, international technical standards, academic policy, and learning and teaching research and practice.

Development and use of clinical guidelines

The purpose of this chapter is to provide an overview of the development and use of clinical guidelines as a tool for decision making in clinical practice. Nurses have always developed and used tools to guide clinical decision making related to interventions in practice. Since Florence Nightingale (Nightingale 1860) gave us ‘notes’ on nursing in the late 1800s, nurses have continued to use tools, such as standards, policies and procedures, protocols, algorithms, clinical pathways and clinical guidelines, to assist them in making appropriate decisions about patient care that eventuate in the best desired patient outcomes. Clinical guidelines have enjoyed growing popularity as a comprehensive tool for synthesising clinical evidence and information into user-friendly recommendations for practice. Historically, clinical guidelines were developed by individual experts or groups of experts by consensus, with no transparent process for the user to determine the validity and reliability of the recommendations. The acceptance of the evidence-based practice (EBP) movement as a paradigm for clinical decision making underscores the imperative for clinical guidelines to be systematically developed and based on the best available research evidence. Clinicians are faced with the dilemma of choosing from an abundance of guidelines of variable quality, or developing new guidelines. Where do you start? How do you find an existing guideline to fit your practice? How do you know if a guideline is evidence-based, valid and reliable? Should you apply an existing guideline in your practice or develop a new guideline? How do you get clinicians to use the guidelines? How do you know if using the guideline will make any difference in care delivery or patient outcomes? Whatever the choice, the challenge lies in choosing or developing a clinical guideline that is credible as a decision-making tool for the delivery of quality, efficient and effective care. This chapter will address the posed questions through an exploration of the ins and outs of clinical guidelines, from development to application to evaluation.

Establishing content validity of a survey research instrument : the older patients in acute care survey - United States

Geriatric nursing competency in the acute care setting is a social mandate for the 21st century. This article reports on the content validation of an Australian research instrument, the Older Patients in Acute Care Survey (OPACS) that examines the attitudes, the knowledge, and the practices of nurses working with acute care patients. The OPACS tool was developed primarily to assist nurse educators to assess attitudes, knowledge, and practices of nursing staff in caring for older patients in the acute care setting; to evaluate the implementation of institution-specific educational interventions; and to improve quality of care given to older patients. An overall content validity index (CVI) for the OPACS was calculated (CVI = .918), revealing high content validity. Opinions (CVI = .92) and practices (CVI = .97) subconstructs revealed high content validity as well. Therefore, results indicate that the OPACS has high content validity in the U.S. acute care setting and could assist nurse educators in establishing and enhancing nurse competency in the care for geriatric patients in the future.