Dynamics of bigeye (Thunnus obesus) and yellowfin (T. albacares) tuna in Hawaii’s pelagic fisheries: analysis of tagging data with a bulk transfer model incorporating size-specific attrition

Tag release and recapture data of bigeye (Thunnus obesus) and yellowfin tuna (T. albacares) from the Hawaii Tuna Tagging Project (HTTP) were analyzed with a bulk transfer model incorporating size-specific attrition to infer population dynamics and transfer rates between various fishery components. For both species, the transfer rate estimates from the offshore handline fishery areas to the longline fishery area were higher than the estimates of transfer from those same areas into the inshore fishery areas. Natural and fishing mortality rates were estimated over three size classes: yellowfin 20–45, 46–55, and ≥56 cm and bigeye 29–55, 56–70, and ≥71 cm. For both species, the estimates of natural mortality were highest in the smallest size class. For bigeye tuna, the estimates decreased with increasing size and for yellowfin tuna there was a slight increase in the largest size class. In the Cross Seamount fishery, the fishing mortality rate of bigeye tuna was similar for all three size classes and represented roughly 12% of the gross attrition rate (includes fishing and natural mortality and emigration rates). For yellowfin tuna, fishing mortality ranged between 7% and 30%, the highest being in the medium size class. For both species, the overall attrition rate from the entire fishery area was nearly the same. However, in the specific case of the Cross Seamount fishery, the attrition rate for yellowfin tuna was roughly twice that for bigeye. This result indicates that bigeye tuna are more resident at the Seamount than yellowfin tuna, and larger bigeye tunas tend to reside longer than smaller individuals. This may result in larger fish being more vulnerable to capture in the Seamount fishery. The relatively low level of exchange between the Sea-mount and the inshore and longline fisheries suggests that the fishing activity at the Seamount need not be of great management concern for either species. However, given that the current exploitation rates are considered moderate (10–30%), and that Seamount aggregations of yellowfin and bigeye tuna are highly vulnerable to low-cost gear types, it is recommended that further increases in fishing effort for these species be monitored at Cross Seamount.

Friction and material transfer in micro-scale sliding contact between aluminium alloy and steel

A ball-on-flat reciprocating micro-tribometer has been used to measure the friction coefficient between aluminium alloy strip and a steel ball. A relatively small ball and correspondingly low contact load is used to give a contact width of the order of 100μm, closer to asperity contact widths than generally found for this type of test. The effects of load, initial strip surface roughness, lubricants and boundary additives are investigated. It is found that the friction coefficient is significantly reduced by the addition of a lubricant. Observations of the wear tracks and ball surface show that the material transfer from aluminium to the ball is reduced in the presence of the lubricant. The initial friction coefficient is further reduced by the addition of a boundary additive, but the friction coefficient after 8 cycles is unchanged. Copyright © 2004 by Springer Science+Business Media, Inc.

Heat transfer and aerodynamics of turbine blade tips in a linear cascade

Local measurements of the heat transfer coefficient and pressure coefficient were conducted on the tip and near tip region of a generic turbine blade in a five-blade linear cascade. Two tip clearance gaps were used: 1.6% and 2.8% chord. Data was obtained at a Reynolds number of 2.3 × 10 5 based on exit velocity and chord. Three different tip geometries were investigated: a flat (plain) tip, a suction-side squealer, and a cavity squealer. The experiments reveal that the flow through the plain gap is dominated by flow separation at the pressure-side edge and that the highest levels of heat transfer are located where the flow reattaches on the tip surface. High heat transfer is also measured at locations where the tip-leakage vortex has impinged onto the suction surface of the aerofoil. The experiments are supported by flow visualisation computed using the CFX CFD code which has provided insight into the fluid dynamics within the gap. The suction-side and cavity squealers are shown to reduce the heat transfer in the gap but high levels of heat transfer are associated with locations of impingement, identified using the flow visualisation and aerodynamic data. Film cooling is introduced on the plain tip at locations near the pressure-side edge within the separated region and a net heat flux reduction analysis is used to quantify the performance of the successful cooling design. copyright © 2005 by ASME.

The effect of work processes on the casing heat transfer of a transonic turbine

This paper considers the effect of the rotor tip on the casing heat load of a transonic axial flow turbine. The aim of the research is to understand the dominant causes of casing heat-transfer. Experimental measurements were conducted at engine-representative Mach number, Reynolds number and stage inlet to casing wall temperature ratio. Time-resolved heat-transfer coefficient and gas recovery temperature on the casing were measured using an array of heat-transfer gauges. Time-resolved static pressure on the casing wall was measured using Kulite pressure transducers. Time-resolved numerical simulations were undertaken to aid understanding of the mechanism responsible for casing heat load. The results show that between 35% and 60% axial chord the rotor tip-leakage flow is responsible for more than 50% of casing heat transfer. The effects of both gas recovery temperature and heat transfer coefficient were investigated separately and it is shown that an increased stagnation temperature in the rotor tip gap dominates casing heat-transfer. In the tip gap the stagnation temperature is shown to rise above that found at stage inlet (combustor exit) by as much as 35% of stage total temperature drop. The rise in stagnation temperature is caused by an isentropic work input to the tip-leakage fluid by the rotor. The size of this mechanism is investigated by computationally tracking fluid path-lines through the rotor tip gap to understand the unsteady work processes that occur. Copyright © 2005 by ASME.

LES and hybrid LES/RANS simulations for conjugate heat transfer over a matrix of cubes

Large Eddy Simulation (LES) and a novel k -l based hybrid LES/RANS approach have been applied to simulate a conjugate heat transfer problem involving flow over a matrix of surface mounted cubes. In order to assess the capability and reliability of the newly developed k -l based hybrid LES/RANS, numerical results are compared with new LES and existing RANS results. Comparisons include mean velocity profiles, Reynolds stresses and conjugate heat transfer. As well as for hybrid LES/RANS validation purposes, the LES results are used to gain insights into the complex flow physics and heat transfer mechanisms. Numerical simulations show that the hybrid LES/RANS approach is effective. Mean and instantaneous fluid temperatures adjacent to the cube surface are found to strongly correlate with flow structure. Although the LES captures more mean velocity field complexities, broadly time averaged wake temperature fields are found similar for the LES and hybrid LES/RANS. Copyright © 2005 by the American Institute of Aeronautics and Astronautics, Inc. All rights reserved.