Biocatálise aplicada à valorização de óleos alimentares usados

O crescente consumo de energia, bem como a possibilidade de esgotamento dos recursos não renováveis, tem fomentado a busca de fontes de energia alternativas. O biodiesel é um biocombustível obtido a partir de fontes renováveis e a sua utilização permite reduzir as emissões de gases com efeito de estufa. Nos últimos anos tem-se produzido biodiesel a partir de óleos alimentares usados (OAU), sendo que com esta aplicação valoriza-se um resíduo e simultaneamente produz-se um combustível “verde”. O biodiesel é produzido através das reações de transesterificação e/ou esterificação entre triglicerídeos e/ou ácidos gordos livres e um álcool, na presença de um catalisador. O rendimento do processo está estritamente relacionado com o tipo de catalisador e as condições que este opera. O principal objetivo do presente trabalho consistiu na avaliação do efeito de alguns parâmetros operacionais no desempenho de uma lípase imobilizada (Novozyme® 435), nomeadamente: (i) índice de acidez do óleo, (ii) razão mássica de enzima/óleo e (iii) método regeneração da enzima com vista à sua reutilização. Também foi objeto de estudo do presente trabalho a produção em contínuo, num (bior)reator tubular de leito fixo, de ésteres metílicos de ácidos gordos (FAME) usando a referida enzima. Registou-se um aumento rendimento em com o incremento do índice de acidez do óleo usado, o que indicia que a enzima catalisa simultaneamente as reações de esterificação e transesterificação. Relativamente à razão mássica de enzima/óleo, dentro da gama testada verificou-se um aumento do rendimento em FAME com a concentração da enzima em meio reacional. Dos vários solventes testados, a aplicação de solvente tert-butanol na regeneração (com incubação) da enzima foi o que melhores resultados teve. Finalmente, os resultados obtidos no ensaio de produção de FAME num biorreator contínuo são motivadores, criando expectativas de uma possível aplicação industrial no futuro.

Readings in the UK energy security

Over the last few decades, the debate about “Peak Oil” became increasingly common and frustrating to governments, oil companies, and individuals. Also in the last decade or so, some unusual events took place which have raised the concern about the future of energy resources. These events lead policy makers to consider what is known today as “Energy Security.” The UK is one of these countries that fears the unknown future should petroleum resources worldwide become scarce or vanish. After the dwindling of the North Sea production, the UK found itself on the brink of losing its energy self-sufficiency. This article asks the questions: Has the UK’s oil and gas production peaked yet? If so, does the UK have a serious energy security problem, and if so, how may this problem be solved and what are the possible short, medium, and long-term solutions for such a concern? In answering these questions, the article discusses the concerns and challenges to the UK energy security and brings about the government plans for tackling these concerns. It is found that the UK does not experience an energy security problem on the short to medium-term, but it may suffer energy insecurity on the longer-term.

O potencial energético do gradiente térmico na plataforma continental do sul do brasil

O crescimento da demanda energética, prevista para a metade do século XXI, com números embasados no crescimento demográfico e de consumo dos países em desenvol- vimento, sugere a busca por fontes energéticas renováveis e de menor impacto ao meio ambiente, conforme os tratados da política internacional. Portanto, o fornecimento de energia suplementar se torna vital nas sociedades modernas e sua extensão até o mar tem se constituído uma recente preocupação do ponto de vista enérgico e ecológico. Várias formas de conversão de energia foram desenvolvidas no decorrer dos anos, com destaque para a energia dos gradientes térmicos. A Plataforma Continental Sul do Bra- sil (PSCB) possui alta variabilidade espacial e temporal nos campos de temperatura, de forma que existe a necessidade de uma análise das regiões de maior potencial energético com respeito ao gradiente vertical de temperatura. Neste estudo, foram utilizados dados do modelo OCCAM com uma grade de resolu- ção horizontal de 0, 25o e resolução vertical de 66 níveis, distribuídos ao longo de um sistema de coordenadas vertical. Foram utilizadas imagens de temperatura superfícial do mar (TSM) obtidas a partir do sensor AVHRR (Advanced Very High Resolution Ra- diometer) de forma a realizar a validação dos dados do modelo OCCAM. A análise da média dos dados do modelo indicou um sítio energético de maior viabilidade devido oC ao padrão médio do gradiente térmico de aproximadamente 0, 17 ao longo da coluna vertical (545 m de profundidade) no oceano. Neste local, foram coletados os dados, e aplicados a um módulo de conversão de energia térmica dos oceanos que vem sendo desenvolvido na Universidade Federal do Rio Grande - FURG. A região de estudo de- monstrou possuir um local com ótimo potencial energético, onde a produção máxima de energia pode alcançar 111, 9MW , associada com um padrão variabilidade tempo- ral dominante de 12 meses. Este sítio energético demonstra maior eficiência durante o período de verão e outono ao longo dos anos e sua média para todo o período é de 94, 3MW . Neste estudo, duas correntes: Corrente do Brasil (CB) e a Contra Corrente Costeira (CCC), com águas de origem tropical e subantártica com aportes continentais, respecti- vamente, tem alta correlação com os valores dos gradientes térmicos e com os significa- tivos eventos de conversão energética. O sítio energético demonstrou alta estabilidade à sazonalidade e à gama de eventos meteorológicos e oceanográficos, de forma que pode ser qualificado como uma fonte suplementar a matriz energética do país para um futuro próximo.

Oceans of energy? The non-linear trajectory of the emerging wave energy technology

This paper addresses the construction and structuring of a technological niche – i.e. a protected space where promising but still underperforming technologies are stabilized and articulated with societal needs – and discusses the processes that influence niche development and may enable niche breakout. In theoretical terms the paper is grounded on the multi-level approach to sustainability transitions, and particularly on the niche literature. But it also attempts to address the limitations of this literature in what concerns the spatial dimension of niche development. It is argued that technological niches can transcend the narrow territorial boundaries to which they are often confined, and encompass communities and actions that span several spatial levels, without losing some territorial embeddedness. It is further proposed that these features shape the niche trajectory and, therefore, need to be explicitly considered by the niche theoretical framework. To address this problem the paper builds on and extends the socio-cognitive perspective to technology development, introducing a further dimension – space – which broadens the concept of technological niche and permits to better capture the complexity of niche behaviour. This extended framework is applied to the case of an emerging renewable energy technology – wave energy - which exhibits a particularly slow and non-linear development trajectory. The empirical analysis starts by examining how an “overall niche space” in wave energy was spatially constructed over time. Then it investigates in greater detail the niche development processes that took place in Portugal, a country that was among the pioneers in the field, and whose actors have been, from very early stages, engaged in the activities conducted at various spatial levels. Through this combined analysis, the paper seeks to understand whether and how niche development is shaped by processes taking place at different spatial levels. More specifically it investigates the interplay between territorial and relational elements in niche development, and how these different dynamics influence the performance of the niche processes and impact on the overall niche trajectory. The results confirm the niche multi-spatial dynamics, showing that it is shaped by the interplay between a niche relational space constructed by actors’ actions and interactions on/across levels, and the territorial effects introduced by these actors’ embeddedness in particular geographical and institutional settings. They contribute to a more precise understanding of the processes that can accelerate or slow down the trajectory of a technological niche. In addition, the results shed some light into the niche activities conducted in/originating from a specific territorial setting - Portugal - offering some insights into the behaviour of key actors and its implications for the positioning of the country in the emerging field, which can be relevant for the formulation of strategies and policies for this area.

Responses to various protein and energy supplements by steers fed low-quality tropical hay. 1. Comparison of response surfaces for young steers

Response curves were established for different supplements, offered at intakes ranging from 0 to 20 g/kg liveweight (W).day to young Bos indicus crossbred steers fed low-quality Rhodes grass (Chloris gayana) hay ad libitum in two pen experiments. Supplements included protein meals of varying rumen-degradability (cottonseed meal (CSM) or fishmeal), as well as ‘energy sources��� comprising grains of high and low ruminal starch degradability (barley and sorghum) and a highly fermentable sugar source (molasses), with all diets adjusted for rumen-degradable nitrogen and mineral content. Unsupplemented steers gained 0.08 and 0.15 kg/day, in Experiments 1 and 2, respectively. Growth of steers increased linearly with intake of ‘energy source’ supplements in increasing order of molasses, sorghum and barley (all differences P < 0.05). Steer growth rate also increased linearly with fishmeal, albeit over a narrow intake range (0–4.1 g/kg W.day), whereas the response with CSM was asymptotic, showing a steep response at low intake before levelling at ~1.2 kg/day. All supplement types were associated with a linear reduction in hay intake by the steers (energy substitution) where the reduction was greater (P < 0.05) for barley and molasses (not different) than for sorghum (P < 0.05), and for fishmeal compared with CSM (P < 0.05). In concurrent metabolism studies with the same rations, organic matter digestibility of the total ration (561–578 g/kg DM, unsupplemented) was increased linearly by barley and molasses (both P < 0.05) but was unaffected by CSM and sorghum supplements. The efficiency of microbial protein synthesis in steers increased linearly, from 91 g microbial crude protein/kg digestible organic matter (unsupplemented), in both molasses and CSM-supplemented steers, with the trend for a higher response to molasses (P = 0.05), and appeared most closely related to digestible organic matter intake. The response curves from these studies provide the practical framework upon which to formulate rations for cattle grazing low-quality forages.

Application of the nZEB methodology in the retrofitting of a typical Portuguese dwelling from the 60's.

Buildings and the whole built environment are in a key role when societies are mitigating climate change and adapting to its consequences. More than 50% of the existing residential buildings in EU-25 were built before 1970. Thus, these buildings are of significant importance in reducing energy consumption and CO2 emissions. The existence of more nearly zero energy buildings (nZEB) is a possible solution for this problem. This study aims to analyze the application of the nZEB methodology in the retrofitting of a typical Portuguese dwelling build in 1950. It was shown that the primary energy used can be reduced to a very low value (11,95 kWhep/m2.y) in comparison with the reference consumption (69,15 kWhep/m2.y), with the application of the best construction techniques together with the use of energy from on-site renewable sources.

Probabilistic design optimization of horizontal axis wind turbine rotors

Considerable interest in renewable energy has increased in recent years due to the concerns raised over the environmental impact of conventional energy sources and their price volatility. In particular, wind power has enjoyed a dramatic global growth in installed capacity over the past few decades. Nowadays, the advancement of wind turbine industry represents a challenge for several engineering areas, including materials science, computer science, aerodynamics, analytical design and analysis methods, testing and monitoring, and power electronics. In particular, the technological improvement of wind turbines is currently tied to the use of advanced design methodologies, allowing the designers to develop new and more efficient design concepts. Integrating mathematical optimization techniques into the multidisciplinary design of wind turbines constitutes a promising way to enhance the profitability of these devices. In the literature, wind turbine design optimization is typically performed deterministically. Deterministic optimizations do not consider any degree of randomness affecting the inputs of the system under consideration, and result, therefore, in an unique set of outputs. However, given the stochastic nature of the wind and the uncertainties associated, for instance, with wind turbine operating conditions or geometric tolerances, deterministically optimized designs may be inefficient. Therefore, one of the ways to further improve the design of modern wind turbines is to take into account the aforementioned sources of uncertainty in the optimization process, achieving robust configurations with minimal performance sensitivity to factors causing variability. The research work presented in this thesis deals with the development of a novel integrated multidisciplinary design framework for the robust aeroservoelastic design optimization of multi-megawatt horizontal axis wind turbine (HAWT) rotors, accounting for the stochastic variability related to the input variables. The design system is based on a multidisciplinary analysis module integrating several simulations tools needed to characterize the aeroservoelastic behavior of wind turbines, and determine their economical performance by means of the levelized cost of energy (LCOE). The reported design framework is portable and modular in that any of its analysis modules can be replaced with counterparts of user-selected fidelity. The presented technology is applied to the design of a 5-MW HAWT rotor to be used at sites of wind power density class from 3 to 7, where the mean wind speed at 50 m above the ground ranges from 6.4 to 11.9 m/s. Assuming the mean wind speed to vary stochastically in such range, the rotor design is optimized by minimizing the mean and standard deviation of the LCOE. Airfoil shapes, spanwise distributions of blade chord and twist, internal structural layup and rotor speed are optimized concurrently, subject to an extensive set of structural and aeroelastic constraints. The effectiveness of the multidisciplinary and robust design framework is demonstrated by showing that the probabilistically designed turbine achieves more favorable probabilistic performance than those of the initial baseline turbine and a turbine designed deterministically.

Dynamic model development of adiabatic compressed air energy storage

The share of variable renewable energy in electricity generation has seen exponential growth during the recent decades, and due to the heightened pursuit of environmental targets, the trend is to continue with increased pace. The two most important resources, wind and insolation both bear the burden of intermittency, creating a need for regulation and posing a threat to grid stability. One possibility to deal with the imbalance between demand and generation is to store electricity temporarily, which was addressed in this thesis by implementing a dynamic model of adiabatic compressed air energy storage (CAES) with Apros dynamic simulation software. Based on literature review, the existing models due to their simplifications were found insufficient for studying transient situations, and despite of its importance, the investigation of part load operation has not yet been possible with satisfactory precision. As a key result of the thesis, the cycle efficiency at design point was simulated to be 58.7%, which correlated well with literature information, and was validated through analytical calculations. The performance at part load was validated against models shown in literature, showing good correlation. By introducing wind resource and electricity demand data to the model, grid operation of CAES was studied. In order to enable the dynamic operation, start-up and shutdown sequences were approximated in dynamic environment, as far as is known, the first time, and a user component for compressor variable guide vanes (VGV) was implemented. Even in the current state, the modularly designed model offers a framework for numerous studies. The validity of the model is limited by the accuracy of VGV correlations at part load, and in addition the implementation of heat losses to the thermal energy storage is necessary to enable longer simulations. More extended use of forecasts is one of the important targets of development, if the system operation is to be optimised in future.

Síntese de carboidratos por microalgas e produção de bioetanol

A maior parte da energia hoje consumida no mundo é derivada de fontes como petróleo, carvão e gás natural. Essas fontes, no entanto, não são renováveis e podem se esgotar em data futura. Nas últimas décadas, as fontes renováveis de combustíveis de base biológica, em especial o bioetanol, têm sido consideradas como alternativa à matriz energética convencional. Porém, existe a necessidade de ampliação da oferta de matérias-primas para produção de etanol, sem pressionar a área plantada para produção de alimentos, o que tem levado empresas e países a investirem em pesquisas para maior utilização de outras matériasprimas. As microalgas surgem como uma das alternativas mais promissoras para a produção de bioetanol, sendo que modificações nas condições de cultivo podem propiciar incremento na concentração de carboidratos destas. Neste contexto, o objetivo deste trabalho foi avaliar a influência da concentração de nutrientes na concentração de carboidratos de microalgas e produzir bioetanol a partir destas. Avaliou-se a síntese de carboidratos das microalgas Chlorella homosphaera e Spirulina platensis LEB 52 em cultivos mixotróficos com diferentes concentrações do componente nitrogenado e cloreto de sódio adicionados aos meios de cultivo. Para a microalga Chlorella minutissima, foram avaliados os efeitos do meio de cultivo e das concentrações dos componentes nitrogenado e fosfatados utilizados no meio de cultivo da microalga sobre a concentração de carboidratos desta. Foram realizadas fermentações alcoólicas utilizando como substrato biomassa das microalgas Chlorella pyrenoidosa e Spirulina sp. LEB 18 acrescidos de glicose e sacarose. Para a microalga Chlorella homosphaera, a maior produtividade em carboidratos foi obtida nos ensaios realizados com a maior concentração de KNO3 com menor concentração de NaCl e menor concentração de KNO3 com maior concentração de NaCl (0,014±0,001 g.L-1 .d-1 e 0,015±0,002 g.L-1 .d-1 , respectivamente). A maior produtividade em carboidratos nos cultivos de Spirulina platensis LEB 52 (0,116±0,002 g.L-1 .d-1 ) foi verificada no experimento no qual a microalga foi cultivada nas menores concentrações de NaNO3 e NaCl. A microalga Spirulina platensis LEB 52 apresentou maior produtividade em carboidratos quando comparada à microalga Chlorella homosphaera. A microalga Chlorella minutissima cultivada em meio Basal, com adição de 0,125 g.L-1 do componente nitrogenado (KNO3) e sem adição dos componentes fosfatados (K2HPO4 e KH2PO4) apresentou a maior produtividade em carboidratos nos cultivos (0,030±0,002 g.L-1 .d-1 ). O ensaio com biomassa de Spirulina sp. LEB 18 com adição de glicose apresentou eficiência superior na formação de etanol e produtividade em etanol (68,487±2,592% e 1,182±0,051g.L-1 .h-1 , respectivamente).

Study of salinity gradients in the Persian Gulf and an experimental model for electric energy extraction from them using nano-membranes

Salinity gradient power (SGP) is the energy that can be obtained from the mixing entropy of two solutions with a different salt concentration. River estuary, as a place for mixing salt water and fresh water, has a huge potential of this renewable energy. In this study, this potential in the estuaries of rivers leading to the Persian Gulf and the factors affecting it are analysis and assessment. Since most of the full water rivers are in the Asia, this continent with the potential power of 338GW is a second major source of energy from the salinity gradient power in the world (Wetsus institute, 2009). Persian Gulf, with the proper salinity gradient in its river estuaries, has Particular importance for extraction of this energy. Considering the total river flow into the Persian Gulf, which is approximately equal to 3486 m3/s, the amount of theoretical extractable power from salinity gradient in this region is 5.2GW. Iran, with its numerous rivers along the coast of the Persian Gulf, has a great share of this energy source. For example, with study calculations done on data from three hydrometery stations located on the Arvand River, Khorramshahr Station with releasing 1.91M/ energy which is obtained by combining 1.26m3 river water with 0.74 m3 sea water, is devoted to itself extracting the maximum amount of extractable energy. Considering the average of annual discharge of Arvand River in Khorramshahr hydrometery station, the amount of theoretical extractable power is 955 MW. Another part of parameters that are studied in this research, are the intrusion length of salt water and its flushing time in the estuary that have a significant influence on the salinity gradient power. According to the calculation done in conditions HWS and the average discharge of rivers, the maximum of salinity intrusion length in to the estuary of the river by 41km is related to Arvand River and the lowest with 8km is for Helle River. Also the highest rate of salt water flushing time in the estuary with 9.8 days is related to the Arvand River and the lowest with 3.3 days is for Helle River. Influence of these two parameters on reduces the amount of extractable energy from salinity gradient power as well as can be seen in the estuaries of the rivers studied. For example, at the estuary of the Arvand River in the interval 8.9 days, salinity gradient power decreases 9.2%. But another part of this research focuses on the design of a suitable system for extracting electrical energy from the salinity gradient. So far, five methods have been proposed to convert this energy to electricity that among them, reverse electro-dialysis (RED) method and pressure-retarded osmosis (PRO) method have special importance in practical terms. In theory both techniques generate the same amount of energy from given volumes of sea and river water with specified salinity; in practice the RED technique seems to be more attractive for power generation using sea water and river water. Because it is less necessity of salinity gradient to PRO method. In addition to this, in RED method, it does not need to use turbine to change energy and the electricity generation is started when two solutions are mixed. In this research, the power density and the efficiency of generated energy was assessment by designing a physical method. The physical designed model is an unicellular reverse electro-dialysis battery with nano heterogenic membrane has 20cmx20cm dimension, which produced power density 0.58 W/m2 by using river water (1 g NaCl/lit) and sea water (30 g NaCl/lit) in laboratorial condition. This value was obtained because of nano method used on the membrane of this system and suitable design of the cell which led to increase the yield of the system efficiency 11% more than non nano ones.

Modelling of an efficient dynamic smart solar photovoltaic power grid system

A smart solar photovoltaic grid system is an advent of innovation coherence of information and communications technology (ICT) with power systems control engineering via the internet [1]. This thesis designs and demonstrates a smart solar photovoltaic grid system that is selfhealing, environmental and consumer friendly, but also with the ability to accommodate other renewable sources of energy generation seamlessly, creating a healthy competitive energy industry and optimising energy assets efficiency. This thesis also presents the modelling of an efficient dynamic smart solar photovoltaic power grid system by exploring the maximum power point tracking efficiency, optimisation of the smart solar photovoltaic array through modelling and simulation to improve the quality of design for the solar photovoltaic module. In contrast, over the past decade quite promising results have been published in literature, most of which have not addressed the basis of the research questions in this thesis. The Levenberg-Marquardt and sparse based algorithms have proven to be very effective tools in helping to improve the quality of design for solar photovoltaic modules, minimising the possible relative errors in this thesis. Guided by theoretical and analytical reviews in literature, this research has carefully chosen the MatLab/Simulink software toolbox for modelling and simulation experiments performed on the static smart solar grid system. The auto-correlation coefficient results obtained from the modelling experiments give an accuracy of 99% with negligible mean square error (MSE), root mean square error (RMSE) and standard deviation. This thesis further explores the design and implementation of a robust real-time online solar photovoltaic monitoring system, establishing a comparative study of two solar photovoltaic tracking systems which provide remote access to the harvested energy data. This research made a landmark innovation in designing and implementing a unique approach for online remote access solar photovoltaic monitoring systems providing updated information of the energy produced by the solar photovoltaic module at the site location. In addressing the challenge of online solar photovoltaic monitoring systems, Darfon online data logger device has been systematically integrated into the design for a comparative study of the two solar photovoltaic tracking systems examined in this thesis. The site location for the comparative study of the solar photovoltaic tracking systems is at the National Kaohsiung University of Applied Sciences, Taiwan, R.O.C. The overall comparative energy output efficiency of the azimuthal-altitude dual-axis over the 450 stationary solar photovoltaic monitoring system as observed at the research location site is about 72% based on the total energy produced, estimated money saved and the amount of CO2 reduction achieved. Similarly, in comparing the total amount of energy produced by the two solar photovoltaic tracking systems, the overall daily generated energy for the month of July shows the effectiveness of the azimuthal-altitude tracking systems over the 450 stationary solar photovoltaic system. It was found that the azimuthal-altitude dual-axis tracking systems were about 68.43% efficient compared to the 450 stationary solar photovoltaic systems. Lastly, the overall comparative hourly energy efficiency of the azimuthal-altitude dual-axis over the 450 stationary solar photovoltaic energy system was found to be 74.2% efficient. Results from this research are quite promising and significant in satisfying the purpose of the research objectives and questions posed in the thesis. The new algorithms introduced in this research and the statistical measures applied to the modelling and simulation of a smart static solar photovoltaic grid system performance outperformed other previous works in reviewed literature. Based on this new implementation design of the online data logging systems for solar photovoltaic monitoring, it is possible for the first time to have online on-site information of the energy produced remotely, fault identification and rectification, maintenance and recovery time deployed as fast as possible. The results presented in this research as Internet of things (IoT) on smart solar grid systems are likely to offer real-life experiences especially both to the existing body of knowledge and the future solar photovoltaic energy industry irrespective of the study site location for the comparative solar photovoltaic tracking systems. While the thesis has contributed to the smart solar photovoltaic grid system, it has also highlighted areas of further research and the need to investigate more on improving the choice and quality design for solar photovoltaic modules. Finally, it has also made recommendations for further research in the minimization of the absolute or relative errors in the quality and design of the smart static solar photovoltaic module.

A new plant growth system rig based on thermodynamic solar energy: a study for energy efficiency assessment

At the present there is a high pressure toward the improvement of all production processes. Those improvements can target distinct factors along the production chain. In particular, and due to recent tight energy efficiency policies, those that involve energy efficiency. As can be expected, agricultural processes are not immune to this tendency. Even more when dealing with indoor productions. In this context, this work presents an innovative system that aims to improve the energy efficiency of a trees growing platform. This improvement in energy consumption is accomplished by replacing an electric heating system by one based on thermodynamic panels. The assessment of the heating fluid caudal and its temperature was experimentally obtained by means of a custom made scaled prototype whose actuators status are commanded by a Fuzzy-based controller. The obtained results suggest that the change in the heating paradigm will lead to overall savings that can easily reach 60% on the energy bill.

Your energy connection

Your energy connection is a South Carolina Energy Office publication on topics related to energy conservation and renewable energy in the state.

Your energy connection

Your energy connection is a South Carolina Energy Office publication on topics related to energy conservation and renewable energy in the state.