Ganhos de peso, taxas de deposição e composição química corporal de tourinhos Santa Gertrudes confinados, recebendo alto concentrado e níveis crescentes de polpa cítrica peletizada

Objetivou-se avaliar a substituição do milho em grão pela polpa cítrica peletizada e seus efeitos sobre os ganhos de peso, as taxas de deposição e a composição química corporal de tourinhos Santa Gertrudes em confinamento. Vinte e oito animais (idade média de nove meses e peso inicial de 277 kg) foram mantidos em baias individuais durante 92 dias, após 21 dias de adaptação. Os animais receberam dietas contendo 20% da MS como silagem de milho que continha 40% de grãos. Foram testados os níveis de 0, 25, 40 e 55% de participação da polpa cítrica peletizada na MS da dieta. A composição química corporal foi estimada a partir de equações desenvolvidas para a mesma raça, utilizando-se a composição química do corte da 9-10-11ª costelas. A participação da polpa cítrica peletizada não afetou significativamente o peso corporal final (449 kg) e os ganhos diários de peso corporal (1,50 kg), de corpo vazio (1,26 kg) e de carcaça (0,78 kg). Não houve diferença entre tratamentos para as taxas diárias de deposição de água (0,374 kg), EE (0,589 kg), proteína (0,253 kg), minerais (0,040 kg) e energia (6,934 Mcal) e, conseqüentemente, a composição química corporal final foi similar entre os animais recebendo diferentes níveis de polpa cítrica na dieta. A substituição do milho em grão por polpa cítrica peletizada, até 55% da MS, em dietas para tourinhos em terminação recebendo altos níveis de concentrado, não altera os ganhos de peso, as taxas de deposição e a composição química corporal desses animais.

Algoritmo Q-learning como estratégia de exploração e/ou explotação para metaheurísticas GRASP e algoritmo genético

Techniques of optimization known as metaheuristics have achieved success in the resolution of many problems classified as NP-Hard. These methods use non deterministic approaches that reach very good solutions which, however, don t guarantee the determination of the global optimum. Beyond the inherent difficulties related to the complexity that characterizes the optimization problems, the metaheuristics still face the dilemma of xploration/exploitation, which consists of choosing between a greedy search and a wider exploration of the solution space. A way to guide such algorithms during the searching of better solutions is supplying them with more knowledge of the problem through the use of a intelligent agent, able to recognize promising regions and also identify when they should diversify the direction of the search. This way, this work proposes the use of Reinforcement Learning technique - Q-learning Algorithm - as exploration/exploitation strategy for the metaheuristics GRASP (Greedy Randomized Adaptive Search Procedure) and Genetic Algorithm. The GRASP metaheuristic uses Q-learning instead of the traditional greedy-random algorithm in the construction phase. This replacement has the purpose of improving the quality of the initial solutions that are used in the local search phase of the GRASP, and also provides for the metaheuristic an adaptive memory mechanism that allows the reuse of good previous decisions and also avoids the repetition of bad decisions. In the Genetic Algorithm, the Q-learning algorithm was used to generate an initial population of high fitness, and after a determined number of generations, where the rate of diversity of the population is less than a certain limit L, it also was applied to supply one of the parents to be used in the genetic crossover operator. Another significant change in the hybrid genetic algorithm is the proposal of a mutually interactive cooperation process between the genetic operators and the Q-learning algorithm. In this interactive/cooperative process, the Q-learning algorithm receives an additional update in the matrix of Q-values based on the current best solution of the Genetic Algorithm. The computational experiments presented in this thesis compares the results obtained with the implementation of traditional versions of GRASP metaheuristic and Genetic Algorithm, with those obtained using the proposed hybrid methods. Both algorithms had been applied successfully to the symmetrical Traveling Salesman Problem, which was modeled as a Markov decision process

Desempenho, eficiência de utilização dos nutrientes e estrutura do trato digestório de pintos de corte alimentados na fase pré-inicial com rações de diferentes formas físicas

Este estudo foi realizado com o objetivo de avaliar o efeito da forma física da ração sobre o desempenho, a utilização dos nutrientes das rações e o desenvolvimento do trato disgestório de pintos de corte na primeira semana de vida. Foram utilizados 150 pintos machos Cobb distribuídos ao acaso em três tratamentos com cinco repetições de dez aves. Os tratamentos consistiram das formas físicas farelada, triturada e peletizada de uma ração pré-inicial comercial. Com exceção da moela, os órgãos do trato digestório e a estrutura morfométrica do intestino não foram influenciados pela forma física da ração. Maior digestibilidade do N foi obtida com a ração peletizada, enquanto a ração triturada possibilitou maior digestibilidade do EE. A energia metabolizável determinada para a ração farelada foi menor que a obtida nas demais formas físicas da ração. As aves alimentadas com ração farelada tiveram menor consumo de ração e ganho de peso e pior conversão alimentar. Ingeriram ainda menos energia, apresentaram menores retenções de proteína, gordura e energia corporal e utilizaram maior proporção da energia ingerida para produção de calor. As rações pré-iniciais na forma peletizada ou triturada possibilitam maior aproveitamento dos nutrientes da ração pelos pintos e melhor desempenho.

Efeitos da aplicação de efluente de tratamento de esgoto na fertilidade do solo e produtividade de pepino sob irrigação subsuperficial

O experimento foi conduzido com o objetivo de avaliar técnicas para a aplicação de águas residuárias na agricultura, proporcionando melhor reutilização de água, recurso natural atualmente escasso e muito mal disponibilizado. Utilizou-se da cultura de pepino (Cucumis sativus L.) em estufa, com oito parcelas irrigadas com efluentes de tratamento de esgoto residencial e oito parcelas irrigadas com água tratada e distribuída pela SABESP (tratamento-testemunha), ambas abastecidas por sistema de irrigação subsuperficial, avaliando-se a produção média por planta, a fertilidade do solo e a disposição de nutrientes na água do solo. Nas análises do solo, verificaram-se maiores teores de P, K e CTC no solo irrigado com efluentes. Nesse mesmo tratamento, constataram-se os maiores teores de N, nitrato, Ca, Mg, Zn e S para as análises da água retida na matriz do solo. Quanto à produção total média por planta, as parcelas irrigadas com efluente apresentaram 2.769,6 g de matéria fresca, superior aos 1.968,6 g verificados no tratamento-testemunha, demonstrando a importância da utilização de efluente de esgoto para o fornecimento de nutrientes e aumento de produtividade.

Cobre e zinco no material percolado e no solo com a aplicação de água residuaria de suinocultura em solo cultivado com soja

O objetivo deste trabalho foi avaliar possíveis efeitos da aplicação de taxas de água residuária de suinocultura (ARS), quanto às concentrações de cobre e zinco, tanto no solo quanto na água percolada de lisímetros de drenagem, durante o ciclo da cultura da soja. O experimento foi conduzido em ambiente protegido, onde havia 24 lisímetros de drenagem. Semeou-se soja cultivar CD 202, e foram aplicadas ARS nas seguintes dosagens: 0; 100; 200 e 300 m³ ha-1 no ciclo, combinadas com duas adubações na semeadura (com e sem adição da adubação recomendada na semeadura), em três repetições por tratamento. Foram feitas seis coletas do material percolado durante o ciclo da cultura e realizadas determinações de cobre e zinco. No solo, foram feitas três coletas em cada parcela experimental, para a determinação do pH, da matéria orgânica, da capacidade de troca catiônica, do cobre e do zinco. O delineamento foi em blocos casualizados, num esquema fatorial de 4 x 2. Observou-se que o cobre no solo não apresentou diferenças significativas com a aplicação de ARS e adubação, enquanto as concentrações de zinco no solo foram influenciadas pelas taxas aplicadas de ARS. As transferências de cobre e de zinco por percolação foram pouco expressivas.

Sistema automatizado para o aproveitamento de água cinza e azul, com controle de PH utilizando lógica fuzzy

Every day, water scarcity becomes a more serious problem and, directly affects global society. Studies are directed in order to raise awareness of the rational use of this natural asset that is essential to our survival. Only 0.007% of the water available in the world have easy access and can be consumed by humans, it can be found in rivers, lakes, etc... To better take advantage of the water used in homes and small businesses, reuse projects are often implemented, resulting in savings for customers of water utilities. The reuse projects involve several areas of engineering, like Environmental, Chemical, Electrical and Computer Engineering. The last two are responsible for the control of the process, which aims to make gray water (soapy water), and clear blue water (rain water), ideal for consumption, or for use in watering gardens, flushing, among others applications. Water has several features that should be taken into consideration when it comes to working its reuse. Some of the features are, turbidity, temperature, electrical conductivity and, pH. In this document there is a proposal to control the pH (potential Hydrogen) through a microcontroller, using the fuzzy logic as strategy of control. The controller was developed in the fuzzy toolbox of Matlab®

Análise do desempenho térmico de sistema constutivo de concreto com EPS como agregado graúdo

In the last decades there was a concentrate effort of researchers in the search for options to the problem of the continuity of city development and environmental preservation. The recycling and reuse of materials in industry have been considerate as the best option to sustainable development. One of the relevant aspects in this case refers to the rational use of electrical energy. At this point, the role of engineering is to conceive new processes and materials, with the objective of reducing energy consumption and maintaining, at the same time the benefits of the technology. In this context, the objective of the present research is to analyze quantitatively the thermal behavior of walls constructed with concrete blocks which composition aggregates the expanded polystyrene (EPS) reused in the shape of flakes and in the shape of a board, resulting in a “light concrete”. Experiments were conducted, systematically, with a wall (considerate as a standard) constructed with blocks of ordinary concrete; two walls constructed with blocks of light concrete, distinct by the proportion of EPS/sand; a wall of ceramic bricks (“eight holes” type) and a wall with ordinary blocks of cement, in a way to obtain a comparative analysis of the thermal behavior of the systems. Others tests conducted with the blocks were: stress analysis and thermal properties analysis (ρ, cp e k). Based on the results, it was possible to establish quantitative relationship between the concentration (density) of EPS in the constructive elements and the decreasing of the heat transfer rate, that also changes the others thermal properties of the material, as was proved. It was observed that the walls of light concrete presents better thermal behavior compared with the other two constructive systems world wide used. Based in the results of the investigation, there was shown the viability of the use of EPS as aggregate (raw material) in the composition of the concrete, with the objective of the fabrication of blocks to non-structural masonry that works as a thermal insulation in buildings. A direct consequence of this result is the possibility of reduction of the consume of the electrical energy used to climatization of buildings. Other aspect of the investigation that must be pointed was the reuse of the EPS as a raw material to civil construction, with a clear benefit to reducing of environmental problems

Formulação e caracterização de massas de grês porcelanato preparadas a partir de matérias-primas naturais do Rio Grande do norte e com adição de chamote de telhas

Traditional ceramics have an important role in the economy of Rio Grande do Norte. The local industries manufacture over 50 million shingles a month, corresponding to 60% of their overall production. As a result of processing flaws, roughly 20% of the production must be discarded, since little or no use has been envisaged for such fired components. Therefore, the use of this kind of residue, especially in the composition of other ceramic materials, comes as an interesting option from the economical and environmental point of view. In this scenario, the objective of the present study was to assess the effect of the addition of fired shingle waste in the composition of porcelainized stoneware tiles. To that end, two porcelainized stoneware tiles compositions were initially prepared. Subsequently, contents from 10 to 30% of roofing tiles chamote were added to each one of them. All raw materials and grog were characterized by FRX, XRD, and thermal analysis. The ceramics were fired using natural gas for 30 min at different temperatures, i.e. 1150, 1200 and 1250ºC, and fully characterized. The addition of roofing tiles chamote resulted in composition with superior properties compared to additive-free compositions. Porcelainized stoneware tiles products that fulfill required standards for practical applications were achieved

Evaluation of harvested mushrooms and viability of Agaricus bisporus growth using casing materials made from spent mushroom substrate

P>The present work evaluates of harvested mushroom and viability of Agaricus bisporus growth in several casing materials based on spent mushroom substrate. The experiment consisted of eight casing layer, which six were made with spent mushroom substrate. The results confirm the usefulness of reincorporating the spent substrate in new cultivation cycles as an ingredient of casing mixtures. In general, biological efficiency was high, three of the SMS based-casings surpassing the threshold value of 100 kg 100 kg-1 of compost. The high electrical conductivity of mixtures containing a large proportion of spent substrate limits the extent to which it can be used, although mixing it with other materials (such as peat) reduces these values to acceptable levels. In short, it makes economic and environmental sense to reuse spent mushroom substrate as an ingredient of alternative casing materials.

Selectivity of Workers of the Grass-Cutting Ants Atta bisphaerica and Atta capiguara (Hymenoptera: Formicidae) to Vegetable Oils

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desinfecção solar de água para comunidades de baixa renda

The use of solar energy for water disinfection, and is accessible to disadvantaged communities because of its low cost, has the advantage of using disposable materials such as bottles of polyethylene terephthalate (PET). We present a study that used two methods of disinfection: the methodology proposed by the project Solar Water Disinfection (SODIS), which consisted of water disinfection by solar radiation and temperature and the methodology which the temperature of the water for disinfection. In both, we seek to eliminate microorganisms that cause serious diseases such as dysentery, typhoid, cholera, etc. Water samples were collected in the community of Bass, where the population has low income and the incidence of waterborne diseases is high. The experiments were divided into two stages. In step 1 we studied the feasibility of disinfection and in step 2 the feasibility of the pilot plant to obtain adequate levels of disinfection temperatures desired. The results showed the efficiency of the disinfection process, reaching an average of 80 to 100% death of microorganisms, but regrowth was observed in some samples. Finally on the good results of stage 1, is designed and built and tested in an experimental pilot plant, which has shown to be feasible to promote water disinfection through the use of solar energy. The water after treatment is in accordance with the limits established by Brazilian legislation for clean water, maintaining a positive performance for the disinfection and acceptable levels of bacterial regrowth

Obtenção e caracterização de farinha de frutas e vegetais através do uso de um sistema de secagem solar de baixo custo

In this work a solar drying system for food dehydration was developed. It is a direct exposition drying apparatus that uses solar energy to heat the circulating air. First, the construction and assembly of this apparatus was described, in which was used scrap wraps of used tires for thermal insulation, allowing the reuse of solid waste, being an ecologically correct recycling option. After, the results obtained in experiments for cashew drying showed the thermal and economical feasibility of the proposed solar drying system, focusing on the process of flour production and in its chemical characterization. It was also demonstrated the social importance of this production for socially excluded people, since the value added to this fruit, in relation to its in nature form, may represent an option for job and income generation. The main features of the proposed dryer are its low cost and its easy fabrication and assembly process. After cashew drying, the obtained product was processed into flour by using a knife mill and it was added crushed rapadura to reduce the rancid taste caused by tannin

Metodologia, Sistema de Codificação e Ferramenta de software para Modelagem de Móveis Modulados

On this research we investigated how new technologies can help the process of design and manufacturing of furniture in such small manufacturers in Rio Grande do Norte state. Google SketchUp, a 3D software tool, was developed in such a way that its internal structures are opened and can be accessed using SketchUp s API for Ruby and programs written in Ruby language (plugins). Using the concepts of the so-called Group Technology and the flexibility that enables adding new functionalities to this software, it was created a Methodology for Modeling of Furniture, a Coding System and a plugin for Google s tool in order to implement the Methodology developed. As resulted, the following facilities are available: the user may create and reuse the library s models over-and-over; reports of the materials manufacturing process costs are provided and, finally, detailed drawings, getting a better integration between the furniture design and manufacturing process

Avaliação do comportamento tribológico de compósitos poliéster/fibra de vidro utilizando resíduos de poliéster/fibra de vidro e carbonato de cálcio como carga

The use of composite materials and alternative is being increased every day, as it becomes more widespread awareness that the use of renewable and not harmful to the environment is part of a new environmentally friendly model. Since its waste (primarily fiberglass) can not be easily recycled by the difficulty that still exists in this process, since they have two phases mixed, a polymeric matrix thermoset difficult to recycle because it is infusible and phase of fiber reinforcements. Thermoset matrix composites like Polyester + fiberglass pose a threat due to excessive discharge. Aiming to minimize this problem, aimed to reuse the composite Polyester + fiber glass, through the wastes obtained by the grinding of knifes and balls. These residues were incorporated into the new composite Polyester/Fiberglass for hot compression mold and compared tribological to composites with filler CaCO3, generally used as filler, targeting a partial replacement of CaCO3 by such waste. The composites were characterized by thermal analysis (TGA, DSC and DMA), by the surface integrity (roughness determination, contact angle and surface energy), mechanical properties (hardness) and tribological tests (wear and coefficient of dynamic friction) in order to evaluate the effect of loads and characterize these materials for applications that can take, in the tribological point of view since waste Polyester + fiberglass has great potential for replacement of CaCO3

Utilización de compost agotado de champiñón como capa de coberturas en nuevos ciclos de producción

El objetivo de este trabajo fue evaluar el comportamiento agronómico de seis mezclas de cobertura, elaboradas a partir de sustrato postcultivo del champiñón Agaricus bisporus, en nuevos ciclos de cultivo. Los resultados obtenidos mostraron la viabilidad de la reintroducción del sustrato en nuevos ciclos de cultivo, ya sea como material de base único, si se somete a un proceso de lavado para eliminar sales solubles, o bien mezclado con otros materiales de baja conductividad, como es el caso de la turba rubia o la fibra de coco. Se destacan los altos valores de efiCiência biológica registrados, que llegaron hasta los 100 kg kg-1 de compost, similares a los proporcionados por los testigos, y los altos valores relativos observados (con respecto a los testigos) en el contenido en materia seca de los carpóforos cosechados con algunas de las nuevas coberturas elaboradas. Esta reutilización del compost constituye una alternativa interesante, con vistas a reemplazar a las tierras y a los sustratos orgánicos utilizados habitualmente como cobertura, con la doble ventaja de disminuir los costos de elaboración y el impacto ambiental.