Compósitos de matriz metálica à base níquel com adição de TaC e NbC produzidos via metalurgia do pó

Carbide reinforced metallic alloys potentially improve some important mechanical properties required for the overall use of important engineering materials such as steel and nickel. Nevertheless, improved performance is achieved not only by composition enhancement but also by adequate processing techniques, such as novel sintering methods in the case of powder metallurgy. The method minimizes energy losses in addition to providing uniform heating during sintering. Thus, the general objective of this study was to evaluate the density, hardness, flexural strength, dilatometric behavior and to analyze the microstructure of metal matrix composites based nickel with addition of carbides of tantalum and / or niobium when sintered in a conventional furnace and Plasma assisted debinding and sintering (PADS). Initially, were defineds best parameters of granulation, screening and mixing procedure. After, mixtures of carbonyl Ni and 5%, 10% and 15 wt.% NbC and TaC were prepared in a Y-type mixer under wet conditions during 60 minutes. The mixtures were then dried and granulated using 1.5 wt. % paraffin diluted in hexane. Granulates were cold pressed under 600 MPa. Paraffin was then removed from the pressed pellets during a pre-sintering process carried out in a tubular furnace at 500 °C during 30 min. The heating rate was 3 ºC/min. The pellets were then sintered using either a plasma assisted reactor or a conventional resistive tubular furnace. For both methods, the heating rate was set to 8 ºC/min up to 1150 °C. The holding time was 60 minutes. The microstructure of the sintered samples was evaluated by SEM. Brinell hardness tests were also carried out. The results revealed that higher density and higher hardness values were observed in the plasma-assisted sintered samples. Hardness increased with the concentration of carbides in the Ni-matrix. The flexural strength also increased by adding the carbides. The decline was larger for the sample with addition of 5% 5% TaC and NbC. In general, compositions containing added carbide 10% showed less porous and more uniform distribution of carbides in the nickel matrix microstructural appearance. Thus, both added carbide and plasma sintering improved density, hardness, flexural strength and microstructural appearance of the composites

Effect of inulin supplementation in male mice fed with high fat diet on biochemical profile and α-amylase gene expression

Purpose: To evaluate the preventive and therapeutic effects of inulin supplementation in Naval Medical Research Institute (NMRI) male mice fed with high fat diet. Methods: NMRI male mice (n = 36) were divided into three groups. Control (C1), obese (O1) and experimental mice (E1) were fed during 8 weeks as follows: C1 with normal rodent pellet, O1 with high fat diet, and E1 with high fat diet plus 20 % inulin. C2, O2, and E2 were fed as follows: C2 with normal rodent pellets for 12 weeks; O2 with high fat diet during 8 weeks and switched to normal rodent pellet during next 4 weeks; and E2 with high fat diet over a period of 8 weeks and switched to normal rodent pellet plus 20 % inulin for 4 weeks. Body weight, serum glucose, triglycerides, total cholesterol, high density lipoprotein (HDL), low density lipoprotein (LDL), and hepatic α-amylase gene expression were measured. Results: Groups receiving high fat diet showed higher weight (30.71 ± 0.66 g in O2, p < 0.001), nonfasting blood glucose levels (257.69 ± 5.10 mg/dl in O2, p < 0.001), TG (282.15 ± 1.83 mg/dl in O2, (p < 0.001)), and cholesterol levels (335.72 ± 2.23 mg/dl in O2, (p < 0.001)), compared with control. In C2 group, mean body weight was 25.71 ± 0.54 g, non-fasting blood level 161.54 ± 4.48 mg/dl, TG level 214.29 ± 5.54 mg/dl, and cholesterol level 164.29 ±4.57 mg/dl. Compared to obese group, mice receiving inulin showed lower blood glucose levels (223.10 ± 8.7 mg/dl in E2, p < 0.001), body weight (27.86 ± 0.57 g in E2, p < 0.001), TG (232.14 ± 4.02 mg/dl in E2, p < 0.001) and cholesterol (249.97 ± 2.28 in E2, p < 0.001). A slight decrease in hepatic α-amylase gene expression was observed only in E1. Conclusion: Besides its sweetening properties, inulin may also find use as a potential anti-obesity compound.

Desempenho produtivo de Pseudoplatystoma corruscans estocados em sistemas de criação: semi-intensivo (viveiro escavado) e intensivo (tanque-rede)

Objetivou-se comparar o desempenho produtivo e custos de produção de exemplares de pintado, Pseudoplatystoma corruscans, estocados em dois sistemas de criação: semi-intensivo (viveiro escavado, VE) e intensivo (tanque-rede, TR). Trezentos (300) peixes, com um ano de idade, foram estocados, sendo 150 em um VE (médias de peso e comprimento: 1,48±0,46kg e 57,31±6,42cm) e 150 divididos em três TR (médias de peso e comprimento: 1,27±0,34kg e 55,05±4,11cm). Foram alimentados com ração extrusada de 15mm (diâmetro) 40% PB e 3110kcal ED kg-1, ajustada mensalmente à quantidade de ração. Os parâmetros físico-químicos da água, observados durante o experimento, foram temperatura = 24,08°C±3,23; pH=6,89±0,39 e oxigênio dissolvido = 7,57±0,97mg L-1. Os reultados obtidos dos valores médios finais dos comprimentos (VE=74,07±4,34cm; TR=70,33±5,02cm) e pesos dos peixes (VE=3,41±0,58kg e TR=2,94±0,60kg) indicaram desempenho semelhante nos dois sistemas. As médias do fator de condição (0,09-0,036); ganho em peso diário (9,29g dia-1 - 8,95g dia-1); conversão alimentar (3,09-4,15); consumo total de ração (29,60g dia-1 - 74,16g dia-1); índice de crescimento (0,219-0,215) e sobrevivência (97,33-90,67%) para VE e TR, respectivamente. Houve interação significativa entre os sistemas de criação e mês (P<0,05). O quilo de peixe produzido foi de R$ 8,76 (US$ 2,85) e R$ 8,73 (US$ 2,33) para o VE e TR, respectivamente. Embora o VE tenha demonstrado melhor desenvolvimento durante o período e uma vantagem econômica, o índice de crescimento mostrou que ambos os sistemas tiveram desempenhos semelhantes.

Efeito do manejo alimentar no desempenho do matrinxã Brycon amazonicus em tanques de cultivo

O objetivo deste estudo foi avaliar o efeito do horário, taxa e freqüência de alimentação no desempenho do matrinxã (Brycon amazonicus) em tanques de cultivo. O trabalho foi realizado no Centro de Aqüicultura da UNESP, Jaboticabal, SP, no período de outubro de 1997 a janeiro de 1998 sendo realizados três ensaios, em tanques de 200m² subdivididos em 4 de 50 m². No ensaio I foram medidos em 3 períodos (manhã-m; meio do dia-md e tarde-t) o consumo de ração, índice de ingestão, tempo de saciação e velocidade de ingestão em peixes com peso médio de 232,13 g, alimentados com ração extrusada (32% de PB). Não foi observada diferença significativa nos parâmetros analisados. No ensaio II, em peixes com peso médio de 233,98 g, foi medido o consumo médio de ração, em intervalos de duas horas, das 07 às 19 horas. O maior consumo ocorreu quando o matrinxã foi alimentado às 17 horas. No ensaio III, durante 57 dias, os peixes foram alimentados uma vez ao dia (m); uma vez ao dia (t); duas vezes ao dia(m/t) e três vezes ao dia (m,md,t). Peixes com peso médio inicial de 322,25 g receberam ração com 32% de PB, na quantidade de 2% do PV. Não foram observadas diferenças significativas no ganho de peso diário (3,17; 2,80; 3,04 e 2,81 g) e na conversão alimentar aparente (2,11; 2,48; 2,16 e 2,31:1). Concluiu-se que a freqüência de alimentação de uma vez ao dia, em qualquer horário, mostrou ser suficiente.

Ecologia alimentar de aves insetívoras de um fragmento de mata decídua do extremo norte da Mata Atlântica

The diet study of birds has contributed historically as a model for use to understanding ecological patterns and strategies used by several other groups of vertebrates, which are observed in season patterns and temporal availability of resources, and other. This study has as objective generate information concerning the diet of insectivorous birds during rainy season and dry season, as well as analyze Index food importance, niche overlap, niche breadth, electivity, and seasonal availability of prey. The study was conducted in a fragment of about 270 ha (center coordinates and 5 º 53'S 35 ° 23'W). The sampling of birds occurred between March 2008 and December 2009 in three pre-established trails. Catches of birds were performed using 10 mist nets placed in line, where each trails was sampled once a month. Samples of pellets were obtained by means of tartar emetic. Sampling of availability of prey occurred between February 2009 to December 2009. We used two methods of sampling (pitfall traps and Shake cloths). We captured 269 individuals of 21 species of insectivorous birds. We collected 4116 invertebrates of which 3259 in the rainy season and 857 in the dry season. We obtained 174 samples stomach, where 10 species were exclusively insectivorous diet, nine fed on insect/plant material, an insect/plant material/vertebrate and one for insect/vertebrate. During the rainy season was observing difference between the consumption of items with higher food importance. The Coleoptera was item with higher food importance (73%), followed by Formicidae (7%) and Araneae (6%). During the dry season, no difference was found difference between the consumption of items with higher food importance. The Coleoptera was item with higher food importance (34%), followed by seeds (29%) and Formicidae (18%). The highest levels of niche overlap occurred during the rainy season, while the dry season was characterized by high levels of niche 11 segregation. This indicates that the local insectivorous birds community was structured differently between periods. No was found correlation between the values of niche breadth to the mean weight of the body size. We observed seasonal patterns in prey availability, with the peak availability of invertebrates observed seasonal patterns in rainy season. The insectivorous birds selected the same species richness during both periods, showing a specialized diet. Thamnophilus pelzelni was the only species that had their diet influenced by seasonality. Regarding the overall diet of insectivorous birds, observed a high consumption of prey, whose food availability caused the birds could invest and increase their food resources

FACTORS INFLUENCING MATERIAL LOSS DURING IRON ORE PELLET HANDLING

Iron ore concentrate pellets have the potential to fracture and abrade during transportation and handling, which produces unwanted fine particulates and dust. Consequently, pellet producers characterize the abrasion resistance of their pellets, using an Abrasion Index (AI), to indicate whether their products will produce unacceptable levels of fines. However, no one has ever investigated whether the AI correlates to pellet dustiness. During the course of this research, we investigated the relationship between AI and iron ore concentrate pellet dustiness using a wide range of industrial and laboratory pellet samples. The results showed that, in general, AI can be used to indicate high levels of dust. However, for good-quality pellets, there was no correlation between the two. Thus, dust generation from shipping and handling pellets will depend on the quantity of pellets handled and how much they are handled. These results also showed that the type of industrial furnace used to harden iron ore concentrate pellets may affect their fines generation and potential dustiness.

Elemental Analysis and Forensic Comparison of Soils by Laser-Induced Breakdown Spectroscopy (LIBS) and Laser Ablation Inductively Coupled Plasma Mass Spectrometry (LA-ICP-MS)

The elemental analysis of soil is useful in forensic and environmental sciences. Methods were developed and optimized for two laser-based multi-element analysis techniques: laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) and laser-induced breakdown spectroscopy (LIBS). This work represents the first use of a 266 nm laser for forensic soil analysis by LIBS. Sample preparation methods were developed and optimized for a variety of sample types, including pellets for large bulk soil specimens (470 mg) and sediment-laden filters (47 mg), and tape-mounting for small transfer evidence specimens (10 mg). Analytical performance for sediment filter pellets and tape-mounted soils was similar to that achieved with bulk pellets. An inter-laboratory comparison exercise was designed to evaluate the performance of the LA-ICP-MS and LIBS methods, as well as for micro X-ray fluorescence (μXRF), across multiple laboratories. Limits of detection (LODs) were 0.01-23 ppm for LA-ICP-MS, 0.25-574 ppm for LIBS, 16-4400 ppm for µXRF, and well below the levels normally seen in soils. Good intra-laboratory precision (≤ 6 % relative standard deviation (RSD) for LA-ICP-MS; ≤ 8 % for µXRF; ≤ 17 % for LIBS) and inter-laboratory precision (≤ 19 % for LA-ICP-MS; ≤ 25 % for µXRF) were achieved for most elements, which is encouraging for a first inter-laboratory exercise. While LIBS generally has higher LODs and RSDs than LA-ICP-MS, both were capable of generating good quality multi-element data sufficient for discrimination purposes. Multivariate methods using principal components analysis (PCA) and linear discriminant analysis (LDA) were developed for discriminations of soils from different sources. Specimens from different sites that were indistinguishable by color alone were discriminated by elemental analysis. Correct classification rates of 94.5 % or better were achieved in a simulated forensic discrimination of three similar sites for both LIBS and LA-ICP-MS. Results for tape-mounted specimens were nearly identical to those achieved with pellets. Methods were tested on soils from USA, Canada and Tanzania. Within-site heterogeneity was site-specific. Elemental differences were greatest for specimens separated by large distances, even within the same lithology. Elemental profiles can be used to discriminate soils from different locations and narrow down locations even when mineralogy is similar.

White-faced storm-petrels Pelagodroma marina predated by gulls as biological monitors of plastic pollution in the pelagic subtropical northeast atlantic

Marine plastic pollution is rapidly growing and is a source of major concern. Seabirds often ingest plastic debris and are increasingly used as biological monitors of plastic pollution. However, virtually no studies have assessed plastics in seabirds in the deep subtropical North Atlantic. We investigated whether remains of white-faced storm-petrels (WFSP) present in gull pellets could be used for biomonitoring. We analysed 263 pellets and 79.0% of these contained plastic debris originating in the digestive tract of WFSP. Pellets with no bird prey did not contain plastics. Most debris were fragments (83.6%) with fewer plastic pellets (8.2%). Light-coloured plastics predominated (71.0%) and the most frequent polymer was HDPE (73.0%). Stable isotopes in toe-nails of WFSP containing many versus no plastics did not differ, indicating no individual specialisation leading to differential plastic ingestion. We suggest WFSP in pellets are highly suitable to monitor the little known pelagic subtropical Northeast Atlantic.

Characterization of MSW rejected fractions to fulfill RDF requirements and utilization

In order to fulfil European and Portuguese legal requirements, adequate alternatives to traditional municipal waste landfilling must be found namely concerning organic wastes and others susceptible of valorisation. According to the Portuguese Standard NP 4486:2008, refuse derived fuels (RDF) classification is based on three main parameters: lower heating value (considered as an economic parameter), chlorine content (considered as a technical parameter) and mercury content (considered as an environmental parameter). The purpose of this study was to characterize the rejected streams resulting from the mechanical treatment of unsorted municipal solid waste, from the plastic municipal selective collection and from the composting process, in order to evaluate their potential as RDF. To accomplish this purpose six sampling campaigns were performed. Chemical characterization comprised the proximate analysis – moisture content, volatile matter, ashes and fixed carbon, as well as trace elements. Physical characterization was also done. To evaluate their potential as RDF, the following parameters established in the Portuguese standard were also evaluated: heating value and chlorine content. As expected, results show that the refused stream from mechanical treatment is rather different from the selective collection rejected stream and from the rejected from the compost screening in terms of moisture, energetic matter and ashes, as well as heating value and chlorine. Preliminary data allows us to conclude that studied materials have a very interesting potential to be used as RDF. In fact, the rejected from selective collection and the one from composting have a heating value not very different from coal. Therefore, an important key factor may be the blending of these materials with others of higher heating values, after pre-processing, in order to get fuel pellets with good consistency, storage and handling characteristics and, therefore, combustion behavior.

Toxicity of polychlorinated biphenyls and N-phenyl-1-naphthylamine in the juvenile turtle, Chelydra serpentina

Polychlorinated biphenyls (PCBs) and substituted phenylamine antioxidants (SPAs) are two chemical groups that have been used in multiple Canadian industrial processes. Despite the production ban of PCBs in North America in 1977, they are still ubiquitous in the environment and in wildlife tissues. Previous studies of fish, amphibians, birds, and mammals have shown that PCBs are toxic and act as endocrine disruptors. In contrast, SPAs, specifically N-phenyl-1-naphthylamine (PANA), have received very little attention despite their current use in Canada and their expected environmental releases. The effects of PCB and PANA exposures in reptiles remain unknown thus, juvenile Chelydra serpentina were used in this thesis as a model vertebrate to fill in missing toxicity research gaps due to their importance as an environmental indicator. First, food pellets were spiked at an environmentally relevant concentration of the PCB mixture Aroclor 1254 (A1254) to model hepatic bioaccumulation (0.45 μg/g A1254 for 31 days) and depuration (clean food for 50 days) of PCBs in turtles. No significant differences in PCB concentrations were observed between the control and treated animals, suggesting that juvenile turtles exposed to environmentally relevant concentrations of PCBs can likely detoxify low concentrations of PCBs. Additionally, two dose-response experiments were performed using A1254 or PANA spiked food (0-12.7 μg/g and 0-3,446 μg/g, respectively) to determine hepatic toxicity and bioaccumulation in juvenile C. serpentina. An increase in hepatic cyp1a was observed when exposed to the highest dose of both chemicals: 1) for A1254, induction correlated to the significant increase in hepatic PCB congeners that are known to be metabolized by CYP1A; and 2) for PANA, induction suggested that CYP1A has a potential role in its detoxification. PCBs are known endocrine disruptors, but no significant changes were observed for both thyroid receptors (alpha and beta) or by estrogen and androgen receptors. This lack of response, also noted in the PANA exposure, suggests that C. serpentina is less sensitive to endocrine disruption than other vertebrates. Furthermore, the expression of genes involved in cellular stress was not altered in PCB and PANA exposed animals, supporting the resilience of turtles to oxidative stress. This is the first study to demonstrate the toxicity of PCBs and PANA in C. serpentina, demonstrating the turtle’s high tolerance to contamination.

Gräs från våtmark som additiv i bränslepellets : Effekter på pelletskvalitet och energiförbrukning

Because of global warming the energy production development has progressed towards more renewable energy sources. Biomass has great potential in this matter and pellet is already a big market that has increased seven times the past decade. A periodically strained woodchip resource market and statements of short supply in the future has got actors exploring opportunities with other commodities. Grasses such as Canary grass has shown great potential in this matter and in this study a wetland grass is tested as an additive, 0,5, 1,0, 1,5, and 1,9%, with spruce woodchips. The test production series was performed at a production unit located at the department of environmental and energy system at Karlstad University, Karlstad. Quality was controlled accordingly to the European standard and parameters such as energy consumption, moisture content, mechanical durability and bulk density was tested. For comparison, a sample with only spruce wood chips was produced, and a sample containing 1% of a commonly used additive, potato starch. The results showed that a decrease in energy consumption with 14% when 2% wetland grass was added, part of the decline may be due to the increased production flow compared with the reference sample. The positive effects on decrease in energy consumption, that 1% potato starch results in, is equal to reults from 1% wetlandgrass. This indicates lubricating properties in wetlandgrass. This is attributed to that herbaceous plants have a high content of extracts such as waxes and that they cause less friction in the press. Tests also showed that pellet with wetland grass did not qualify the European standard in terms of mechanical durability. Extracts can form a weak boundary layer in the pellet and cause this. A possible trend shows a better mechanical durability with more grass in pellets. The presence of different size of particles can be a reason. Moisture content qualifies according to the European standard but is below optimum 8%. This despite to relatively high moisture content in the mixer. Higher moisture content in the press would certainly result in a generally higher quality. Suggestions for future studies are to produce pellets with greater distribution on the wetland grass added, to easier interpret a connection. Also examine the extracts behavior with different moisture content. For a sustainable development accordingly renewable energy it is important to ensure the future commodity market for pellets. Further studies should be performed to help the development of alternative raw materials in conjunction with pellet production.

Utilisation d’arbres de faible vigueur provenant de forêts feuillues tempérées comme matière première pour la fabrication de granules de bois

La présente étude avait pour objectif de contribuer à une meilleure compréhension de la granulation des bois feuillus par l’évaluation de la possibilité technique de transformer des bois feuillus de faible vigueur (l’érable à sucre et le bouleau jaune) en granules conventionnels et granules de haute qualité, un type prometteur de transport énergétique. Trois études individuelles ont été réalisées et présentées dans cette thèse. La première étude visait à déterminer s’il y a des changements de teneur en extractibles, cendres, et lignine du bois entre les classes de vigueur des arbres. Les teneurs plus élevées en extractibles et en lignine dans les arbres peu vigoureux ont suggéré que ces derniers sont plus appropriés par rapport aux arbres vigoureux pour la conversion en biocombustibles solides. La deuxième étude visait à optimiser des procédés de granulation des bois feuillus. L’étude a porté sur l’influence des paramètres du procédé (la température et la force de compression) et des caractéristiques de la matière première (la taille des particules et la teneur en humidité) sur les propriétés physiques et mécaniques des granules de bois. Le procédé de granulation doit être effectué à une température d’environ 100 °C pour minimiser la force de friction dans le granulateur et à une teneur en humidité d’environ 11,2% pour maximiser la masse volumique et la résistance mécanique des granules produites. Cette étude a également confirmé que les arbres de faible qualité sont plus appropriés pour la fabrication de granules de bois que les arbres vigoureux. La troisième étude visait l’élaboration de granules de haute qualité. L’eau chaude à température élevée a été utilisée pour modifier les propriétés de la matière première avant granulation. Les caractéristiques de granulation du matériau traité ont été significativement améliorées. Les granules produites ont montré des propriétés améliorées incluant une plus faible teneur en cendres, une plus haute densité énergétique, une meilleure résistance à l’eau, et une meilleure résistance mécanique. Les résultats obtenus de toutes ces études ont démontré la nécessité de bien connaître les fondements de la granulation des bois feuillus et les solutions pratiques pour l’utilisation d’arbres feuillus de faible qualité, le premier peut être applicable pour le développement de procédés de granulation et le dernier peut contribuer à long terme à la restauration des forêts feuillues dégradées en termes de santé des forêts et de leur valeur.

Descripción del análisis microbológico realizado mediante maldi-tof en muestras de la fundación santa fe de Bogotá.

Introducción: La rápida detección e identificación bacteriana es fundamental para el manejo de los pacientes críticos que presentan una patología infecciosa, esto requiere de métodos rápidos para el inicio de un correcto tratamiento. En Colombia se usan pruebas microbiología convencional. No hay estudios de espectrofotometría de masas en análisis de muestras de pacientes críticos en Colombia. Objetivo general: Describir la experiencia del análisis microbiológico mediante la tecnología MALDI-TOF MS en muestras tomadas en la Fundación Santa Fe de Bogotá. Materiales y Métodos: Entre junio y julio de 2013, se analizaron 147 aislamientos bacterianos de muestras clínicas, las cuales fueron procesadas previamente por medio del sistema VITEK II. Los aislamientos correspondieron a 88 hemocultivos (60%), 28 urocultivos (19%), y otros cultivos 31 (21%). Resultados: Se obtuvieron 147 aislamientos con identificación adecuada a nivel de género y/o especie así: en el 88.4% (130 muestras) a nivel de género y especie, con una concordancia del 100% comparado con el sistema VITEK II. El porcentaje de identificación fue de 66% en el grupo de bacilos gram negativos no fermentadores, 96% en enterobacterias, 100% en gérmenes fastidiosos, 92% en cocos gram positivos, 100% bacilos gram negativos móviles y 100% en levaduras. No se encontró ninguna concordancia en bacilos gram positivos y gérmenes del genero Aggregatibacter. Conclusiones: El MALDI-TOF es una prueba rápida para la identificación microbiológica de género y especie que concuerda con los resultados obtenidos de manera convencional. Faltan estudios para hacer del MALDI-TOF MS la prueba oro en identificación de gérmenes.

Assessment of the Availability of Forest Biomass for Bioenergy Production in Southwest Portugal.

In 2014, Portugal was the seventh largest pellets producer in the World. Since the shortage of raw material is one of the major obstacles that the Portuguese sellets market faces, the need for a good assessment of biomass availability for energy purposes at both country and regional levels is reinforced. This work uses a Geographical Information System environment and remote sensing data to assess the availability and sustainability of forest biomass residues in a management unit with around 940 ha of maritime pine forest. The period considered goes from 2004 to 2015. The study area is located in Southwestern Portugal, close to a pellets factory; therefore the potential Contribution of the residual biomass generated in the management unit to the production of pellets is evaluated. An allometric function is used for the estimation of maritime pine above ground biomass. With this estimate, and considering several forest operations, the residual biomass available was assessed, according to stand composition and structure. This study shows that, when maritime pine forests are managed to produce wood, the amount of residues available for energy production is small (an average of 0.37 t ha -1  year -1 were generated in the study area between 2004 and 2015). As a contribution to the sustainability of the Portuguese pellets industries, new management models for maritime pine forests may be developed. The effect of the pinewood nematode on the availability of residual biomass can be clearly seen in this study. In the management unit considered, cuts were made to prevent dissemination of the disease. This contributes to a higher availability of forest residues in a specific period of time, but, in the medium term, they lead to a decrease in the amount of residues that can be used for energy purposes.

Simplificação do processo de multiplicação in vitro da oliveira "Olea europaea L."

A oliveira tem sido multiplicada ao longo dos tempos por métodos convencionais de propagação vegetativa como a enxertia e a estacaria lenhosa e semilenhosa. No entanto, estes métodos revelam-se lentos ou ineficientes para determinadas cultivares. No caso da cv. ‘Galega Vulgar’, ainda com grande expressão no olival português, e de difícil enraizamento por estacaria semilenhosa, tem sido usada a micropropagação de modo a contornar essas limitações e assim obter um elevado número de plantas em curto período de tempo. O custo final de produção por este processo ainda é elevado, podendo comprometer a sua aplicação a nível comercial. Grande parte dos custos estão relacionados com a fase de enraizamento in vitro que carece de ambiente estéril e condições de assépsia para a sua execução. Com vista a uma redução de custos associados a esta fase de produção, pretendeu-se com este trabalho testar a viabilidade do enraizamento ex vitro, na ausência de condições de assépsia. Este método poderá permitir uma significativa redução da mão-de-obra, ao mesmo tempo que facilitará a aclimatização das plantas e a obtenção de um sistema radicular de melhor qualidade. Compararam-se as taxas de enraizamento in vitro (controlo), com as obtidas ex vitro. Foram utilizados explantes provenientes de dois clones da cv. ‘Galega Vulgar’, (cl. 1441 e cl. 2022) cultivados e mantidos in vitro há vários anos no Laboratório de Melhoramento e Biotecnologia da Universidade de Évora. Para além do clone foi avaliada a influência do tipo de estaca (basal e apical), da hormona de enraizamento (AIB e ANA), da sua concentração (540 e 3000 ppm) e ainda de dois substratos, Preformas Jiffy® e pastilhas de fibra coco. Os melhores resultados foram obtidos com o clone 1441 em pastilhas de fibra de coco prensada, com o uso de estacas basais. Quanto à auxina, não se observaram diferenças significativas entre a utilização de ANA na concentração de 540 ppm e AIB na concentração de 3000 ppm. A aclimatização das plantas foi conseguida com taxas elevadas de sucesso, independentemente do tratamento utilizado. Conclui-se que a aplicação do método de enraizamento ex vitro simplifica procedimentos e mantém taxas de enraizamento elevadas, conduzindo assim a uma efetiva redução de tempo e custos associados; Simplifying procedures for in vitro propagation of olive “Olea europaea L.” Abstract: The olive tree has been multiplied throughout the ages by conventional methods of vegetative propagation such as grafting and wood or softwood cuttings. These propagation methods are somehow inefficient for certain cultivars. For the CV. ‘Galega Vulgar‘, still with great expression in Portuguese olive orchards, propagation has been attempted by in vitro culture in order to circumvent these limitations and so obtain a large number of plants in short time period. The final production fees associated to this process are still high which may compromise its application to a commercial level. Most of this process fees are related to the in vitro rooting phase which lacks sterile and aseptic conditions for its implementation. Aiming to reduce the costs associated with this production phase, this work tested the feasibility of the ex vitro rooting in the absence of aseptic conditions, which can allow a significant reduction of the manpower involved and an easier plant acclimatization due to its transplant with a balled-root system. In vitro rooting rates (control) were compared with those obtained with the ex vitro experiments. Explants from two clones of the cv. ‘Galega Vulgar‘ (cl. 1441 and cl. 2022), grown and maintained in vitro for several years in the Laboratory of Biotechnology and Plant Breeding of the University of Évora, were used in the trials. In addition to the clone, the effect of the cutting type (basal and apical), the rooting hormone (AIB and ANA), their concentration (540 and 3000 ppm) and two substrates, Preformas Jiffy ® and pressed coco fiber pellets, were also evaluated. The best results were obtained with the clone 1441, when rooted in pressed coco fiber pellets, using basal cuttings. Under this conditions no significant differences were observed between the use of ANA at 540 ppm or AIB in the 3000 ppm. Acclimatization of plants was achieved with high rates of success, regardless of the treatment used. It can be concluded that the application of the ex vitro rooting method allows to maintain high rooting rates, contributing for an effective reduction of time and fees of the rooting process.