Discrete fractional order system vibrations

A theory of free vibrations of discrete fractional order (FO) systems with a finite number of degrees of freedom (dof) is developed. A FO system with a finite number of dof is defined by means of three matrices: mass inertia, system rigidity and FO elements. By adopting a matrix formulation, a mathematical description of FO discrete system free vibrations is determined in the form of coupled fractional order differential equations (FODE). The corresponding solutions in analytical form, for the special case of the matrix of FO properties elements, are determined and expressed as a polynomial series along time. For the eigen characteristic numbers, the system eigen main coordinates and the independent eigen FO modes are determined. A generalized function of visoelastic creep FO dissipation of energy and generalized forces of system with no ideal visoelastic creep FO dissipation of energy for generalized coordinates are formulated. Extended Lagrange FODE of second kind, for FO system dynamics, are also introduced. Two examples of FO chain systems are analyzed and the corresponding eigen characteristic numbers determined. It is shown that the oscillatory phenomena of a FO mechanical chain have analogies to electrical FO circuits. A FO electrical resistor is introduced and its constitutive voltage–current is formulated. Also a function of thermal energy FO dissipation of a FO electrical relation is discussed.

Establishing the main Guidelines for Cast Steel to Produce Truck Parts

Este trabalho foi realizado na Scania CV AB e teve como principal objectivo estabelecer uma diretriz sobre a possível utilização de aços vazados. Existe uma grande necessidade na realização deste trabalho, de forma a apoiar os engenheiros de projecto no seu processo de selecção dos materiais mais adequados, para produzir componentes mais leves e de elevado desempenho. Esta diretriz apresenta informação relacionada com propriedades mecânicas, processos de fundição, vazabilidade, tipologia de defeitos, tratamentos térmicos, soldabilidade e tratamentos superficiais dos aços vazados. Este trabalho foi limitado, na seleção de materiais para componentes do camião, a aços vazados que poderiam ser aplicados em dois componentes específicos: um componente estrutural da carroçaria sujeito a esforços de fadiga e a um colector de gases de combustão, sujeito a fluência, oxidação, fadiga por corrosão, fadiga-térmica e fadiga-mecânica. Foi realizado um benchmark focado nestes dois componentes de forma a saber que materiais são utilizados de momento por outras empresas concorrentes. Foi realizada ainda uma análise sobre possíveis materiais que possam ser aplicados em cada componente referido. Foi conduzida uma caracterização no estado bruto de fundição de um aço inoxidável vazado usado para produzir um protótipo do colector de gases. Esta caracterização consistiu numa análise microestrutural e medição de macro e microdurezas. Além da caracterização inicial, foram aplicados um conjunto de tratamentos térmicos, de forma a estudar a possibilidade de eliminar os carbonetos presentes inicialmente nas fronteiras de grão. As principais conclusões deste trabalho são que o aço vazado apresenta potencial para ser uma escolha válida em diversas aplicações, devido a um leque alargado de propriedades apresentadas tipicamente por este material. Relativamente a aplicações estruturais, o aço vazado é vantajoso comparativamente ao ferro fundido, quando são requeridos, por exemplo, soldabilidade e elevada resistência, combinada com elevada tenacidade à fractura. Para componentes sujeitos a elevadas temperaturas de serviço, o aço inoxidável vazado é vantajoso quando usado a temperaturas superiores a 750°C, apesar do seu elevado custo. O tratamento térmico composto por um recozimento de solubilização seguido de envelhecimento, elimina quase na totalidade os carbonetos presentes nas fronteiras de grão e verifica-se um aumento de dureza através de uma precipitação de carbonetos finamente dispersos na matriz, que poderão também aumentar a resistência à fluência.

Fluência de materiais

A presente dissertação apresenta uma abordagem ao tema Fluência, com um desenvolvimento geral para quatro materiais: madeira, alumínio, betão e aço. No entanto, particularizou-se este estudo apenas para dois destes materiais, a madeira e o alumínio. A madeira é um material viscoelástico, logo fortemente influenciado quando submetido a uma ação constante (Fluência) sendo agravada com alterações do teor em água. Iniciou-se o estudo, com uma introdução aos objetivos principais e a revisão teórica do conhecimento da propriedade mecânica (Fluência). Efetuou-se o estudo inicial para os quatro materiais indicados. Posteriormente, fez-se avaliação do efeito mecânico sortivo durante 60 dias com sete ciclos, em provetes de dimensões 20 x 20 x 400 mm3 (escala 1:10) de madeira de Eucalyptus globulus Labill. Recorrendo ao levantamento de um conjunto de modelos numéricos, procedeu-se ao ajuste e extrapolação do comportamento, em Fluência, para distintos períodos de tempo (1, 10 e 50 anos). Os resultados obtidos demonstraram que a madeira de Eucalipto não apresenta um limite no seu comportamento em Fluência, logo instável para os 60 dias de duração de ensaio. Os diferentes modelos de Fluência (x6) apresentaram uma variabilidade crescente de resultados, de acordo com o aumento de extrapolação dos resultados. Para a espécie de madeira de Eucalipto constatou-se ainda, que o ajuste e extrapolação de deformação para 50 anos ultrapassaram os valores sugeridos pelo Eurocódigo 5. A última parte deste trabalho, incidiu sobre o desenvolvimento da metodologia do ensaio em flexão de 3 provetes de alumínio similares, cujas dimensões eram de 20 x 20 x 400mm3. O objetivo desta metodologia foi avaliar o seu comportamento em Fluência. Numa primeira fase, foi aplicada uma carga contante de 160 kN. E numa segunda fase, foi aplicada o dobro dessa carga sujeita adicionalmente a uma temperatura bastante superior à temperatura ambiente (a rondar os 50 oC). Conclusivamente verificou-se que o alumínio não apresenta deformação por Fluência, para as condições de ensaio apresentadas.

Superficial and deep changes of cellular mechanical properties following cytoskeleton disassembly.

The cytoskeleton, composed of actin filaments, intermediate filaments, and microtubules, is a highly dynamic supramolecular network actively involved in many essential biological mechanisms such as cellular structure, transport, movements, differentiation, and signaling. As a first step to characterize the biophysical changes associated with cytoskeleton functions, we have developed finite elements models of the organization of the cell that has allowed us to interpret atomic force microscopy (AFM) data at a higher resolution than that in previous work. Thus, by assuming that living cells behave mechanically as multilayered structures, we have been able to identify superficial and deep effects that could be related to actin and microtubule disassembly, respectively. In Cos-7 cells, actin destabilization with Cytochalasin D induced a decrease of the visco-elasticity close to the membrane surface, while destabilizing microtubules with Nocodazole produced a stiffness decrease only in deeper parts of the cell. In both cases, these effects were reversible. Cell softening was measurable with AFM at concentrations of the destabilizing agents that did not induce detectable effects on the cytoskeleton network when viewing the cells with fluorescent confocal microscopy. All experimental results could be simulated by our models. This technology opens the door to the study of the biophysical properties of signaling domains extending from the cell surface to deeper parts of the cell.

Life design: Un paradigma per la costruzione della vita professionale nel XXI secolo

In questo inizio di secolo, la nuova organizzazione sociale del lavoro pone una serie di domande e di sfide ai ricercatori che intendono aiutare le persone a progettare la loro vita lavorativa. Nell'era della globalizzazione anche per quanto riguarda il career counseling, abbiamo deciso di affrontare queste problematiche e di dare delle risposte che si caratterizzassero come innovative attraverso la costituzione di un forum di discussione internazionale. Si è proceduto in questo modo per evitare le difficoltà che generalmente si incontrano quando si mettono a punto dei modelli e dei metodi in un Paese e poi si esportano in altre culture con l'intento di adattarli alle stesse. Questo articolo presenta i primi risultati della collaborazione che si è registrata - un modello e dei metodi per la consulenza di orientamento. Il modello per l'intervento nell'ambito dell'approccio Life Design si caratterizza per cinque presupposti relativi al modo di vedere le persone e la loro vita lavorativa. Essi riguardano le possibilità contestuali, i processi dinamici, i progressi non-lineari, le molteplici prospettive e la presenza di pattern personali. Partendo da questi cinque presupposti abbiamo messo a punto un modello basato sull'epistemologia del costruzionismo sociale, che sostiene che la conoscenza e l'identità di un individuo sono i prodotti dell'interazione sociale e che il significato è costruito attraverso il discorso. Questo approccio fa riferimento anche alla teoria della costruzione di sé di Guichard (2005) e della costruzione della vita professionale di Savickas (2005), che descrivono le azioni utili a facilitare la progettazione del proprio futuro. Particolare attenzione viene data agli interventi nel corso dell'arco di vita, olistici, contestuali e preventivi.

Structural analysis of the Paint Lake Deformation Zone, Northern Ontario /

The Paint Lake Deformation Zone (PLDZ), located within the Superior Province of Canada, demarcates a major structural and lithological break between the Onaman-Tashota Terrane to the north and the Beardmore-Geraldton Belt to the south. The PLDZ is an east-west trending lineament, approximately 50 km in length and up to 1 km in width, comprised of an early ductile component termed the Paint Lake Shear Zone and a late brittle component known as the Paint Lake Fault. Structures associated with PLDZ development including S-, C- and C'-fabrics, stretching lineations, slickensides, C-C' intersection lineations, Z-folds and kinkbands indicate that simple shear deformation dominated during a NW-SE compressional event. Movement along the PLDZ was in a dextral sense consisting of an early differential motion with southside- down and a later strike-slip motion. Although the locus of the PLDZ may in part be lithologically controlled, mylonitization which accompanied shear zone development is not dependent on the lithological type. Conglomerate, intermediate and mafic volcanic units exhibit similar mesoscopic and microscopic structures where transected by the PLDZ. Field mapping, supported by thin section analysis, defines five strain domains increasing in intensity of deformation from shear zone boundary to centre. A change in the dominant microstructural deformation mechanism from dislocation creep to diffusion creep is observed with increasing strain during mylonitization. C'-fabric development is temporally associated with this change. A decrease in the angular relationship between C- and C'-fabrics is observed upon attaining maximum strain intensity. Strain profiling of the PLDZ demonstrates the presence of an outer primary strain gradient which exhibits a simple profile and an inner secondary strain gradient which exhibits a more complex profile. Regionally metamorphosed lithologies of lower greenschist facies outside the PLDZ were subjected to retrograde metamorphism during deformation within the PLDZ.

Cadre juridique de l'utilisation de la biométrie au Québec : sécurité et vie privée

La biométrie, appliquée dans un contexte de traitement automatisé des données et de reconnaissance des identités, fait partie de ces technologies nouvelles dont la complexité d’utilisation fait émerger de nouveaux enjeux et où ses effets à long terme sont incalculables. L’envergure des risques suscite des questionnements dont il est essentiel de trouver les réponses. On justifie le recours à cette technologie dans le but d’apporter plus de sécurité, mais, vient-elle vraiment apporter plus de protection dans le contexte actuel? En outre, le régime législatif québécois est-il suffisant pour encadrer tous les risques qu’elle génère? Les technologies biométriques sont flexibles en ce sens qu’elles permettent de saisir une multitude de caractéristiques biométriques et offrent aux utilisateurs plusieurs modalités de fonctionnement. Par exemple, on peut l’utiliser pour l’identification tout comme pour l’authentification. Bien que la différence entre les deux concepts puisse être difficile à saisir, nous verrons qu’ils auront des répercussions différentes sur nos droits et ne comporteront pas les mêmes risques. Par ailleurs, le droit fondamental qui sera le plus touché par l’utilisation de la biométrie sera évidemment le droit à la vie privée. Encore non bien compris, le droit à la vie privée est complexe et son application est difficile dans le contexte des nouvelles technologies. La circulation des données biométriques, la surveillance accrue, le détournement d’usage et l’usurpation d’identité figurent au tableau des risques connus de la biométrie. De plus, nous verrons que son utilisation pourra avoir des conséquences sur d’autres droits fondamentaux, selon la manière dont le système est employé. Les tests de nécessité du projet et de proportionnalité de l’atteinte à nos droits seront les éléments clés pour évaluer la conformité d’un système biométrique. Ensuite, le succès de la technologie dépendra des mesures de sécurité mises en place pour assurer la protection des données biométriques, leur intégrité et leur accès, une fois la légitimité du système établie.

Peindre Rome à la Renaissance (XVe-XVIIe siècles): des loggias à l’antique aux nouveaux systèmes géopolitiques

Actes du colloque international (Rome, Istituto di Studi Romani, 2009 et 2010).

Short Nylon Fibre Reinforced PP: Melt Rheology

Short fiber reinforced thermoplastics have generated much interest these days since fibrous materials tend to increase both mechanical and thermal properties, such as tensile strength, flexural strength, flexural modulus, heat deflection temperature, creep resistance, and some times impact strength of thermoplastics. If the matrix and reinforcement are both based on polymers the composite are recyclable. The rheological behavior of recyclable composites based on nylon fiber reinforced polypropylene (PP) is reported in this paper. The rheological behavior was evaluated both using a capillary rheometer and a torque rheometer. The study showed that the composite became pseudoplastic with fiber content and hence fiber addition did not affect processing adversely at higher shear rates. The torque rheometer data resembled that obtained from the capillary rheometer. The energy of mixing and activation energy of mixing also did not show much variation from that of PP alone.

Studies on grain refinement and alloying additions on the microstructure and mechanical properties of Mg-8Zn-4Al alloy

MAGNESIUM ALLOYS have strong potential for weight reduction in a wide range of technical applications because of their low density compared to other structural metallic materials. Therefore, an extensive growth of magnesium alloys usage in the automobile sector is expected in the coming years to enhance the fuel efficiency through mass reduction. The drawback associated with the use of commercially cheaper Mg-Al based alloys, such as AZ91, AM60 and AM50 are their inferior creep properties above 100ºC due to the presence of discontinuous Mg17A112 phases at the grain boundaries. Although rare earth-based magnesium alloys show better mechanical properties, it is not economically viable to use these alloys in auto industries. Recently, many new Mg-Al based alloy systems have been developed for high temperature applications, which do not contain the Mg17Al12 phase. It has been proved that the addition of a high percentage of zinc (which depends upon the percentage of Al) to binary Mg-Al alloys also ensures the complete removal of the Mg17Al12 phase and hence exhibits superior high temperature properties.ZA84 alloy is one such system, which has 8%Zn in it (Mg-8Zn-4Al-0.2Mn, all are in wt %) and shows superior creep resistance compared to AZ and AM series alloys. These alloys are mostly used in die casting industries. However, there are certain large and heavy components, made up of this alloy by sand castings that show lower mechanical properties because of their coarse microstructure. Moreover, further improvement in their high temperature behaviour through microstructural modification is also an essential task to make this alloy suitable for the replacement of high strength aluminium alloys used in automobile industry. Grain refinement is an effective way to improve the tensile behaviour of engineering alloys. In fact, grain refinement of Mg-Al based alloys is well documented in literature. However, there is no grain refiner commercially available in the market for Mg-Al alloys. It is also reported in the literature that the microstructure of AZ91 alloy is modified through the minor elemental additions such as Sb, Si, Sr, Ca, etc., which enhance its high temperature properties because of the formation of new stable intermetallics. The same strategy can be used with the ZA84 alloy system to improve its high temperature properties further without sacrificing the other properties. The primary objective of the present research work, “Studies on grain refinement and alloying additions on the microstructure and mechanical properties of Mg-8Zn-4Al alloy” is twofold: 1. To investigate the role of individual and combined additions of Sb and Ca on the microstructure and mechanical properties of ZA84 alloy. 2. To synthesis a novel Mg-1wt%Al4C3 master alloy for grain refinement of ZA84 alloy and investigate its effects on mechanical properties.

Influence of Si, Sb and Sr Additions on the Microstructure, Mechanical Properties and Corrosion Behavior of AZ91 Magnesium Alloy

All the exciting work on developing new and better alloys has led older alloys, such as AZ9l , being abandoned by researchers. lt is believed that the full potential of AZ9l in automotive design has not been realized. Whatever works have been carried out on AZ9lalloy to improve its mechanical properties are insufficient in terms of its potential usage in auto industries. Due to the fact that AZ91 offers high room temperature mechanical properties and good castability, still this alloy is a primary choice for the auto component manufactures. Small improvement in its creep properties will have a huge impact in the transportation industries. Hence, in the present work, “Influence of Si, Sb and Sr Additions on the Microstructure, Mechanical Properties and Corrosion Behavior of AZ91 Magnesium Alloy”, an attempt has been made to improve the creep properties of AZ9l alloy through minor alloying elemental additions and to understand its strengthening mechanisms. The effect of alloying additions on the ageing and tensile properties of AZ9l is also studied. In addition to that, role of various intermetallics formed due to the alloying additions on the corrosion properties of AZ9l alloy is investigated.

Ein Beitrag zur realitätsnahen Modellierung und Analyse von stahlfaserverstärkten Stahlbeton- und Stahlbetonflächentragwerken

Das Werkstoffverhalten von stahlfaserfreiem bzw. stahlfaserverstärktem Stahlbeton unter biaxialle Druck- Zugbeanspruchung wurde experimentell und theoretisch untersucht. Die Basis der experimentellen Untersuchungen waren zahlreiche Versuche, die in der Vergangenheit an faserfreiem Stahlbetonscheiben zur Bestimmung des Werkstoffverhaltens von gerissenem Stahlbeton im ebenen Spannungszustand durchgeführt wurden. Bei diesen Untersuchungen wurde festgestellt, dass infolge einer Querzugbeanspruchung eine Abminderung der biaxialen Druckfestigkeit entsteht. Unter Berücksichtigung dieser Erkenntnisse sind zur Verbesserung der Werkstoffeigenschaften des Betons, Stahlbetonscheiben aus stahlfaserverstärktem Beton hergestellt worden. Die aus der Literatur bekannten Werkstoffmodelle für Beton sowie Stahlbeton, im ungerissenen und gerissenen Zustand wurden hinsichtlich der in der Vergangenheit ermittelten Materialeigenschaften des Betons bzw. Stahlbetons unter proportionalen sowie nichtproportionalen äußeren Belastungen erklärt und kritisch untersucht. In den frischen Beton wurden Stahlfasern hinzugegeben. Dadurch konnte die Festigkeits- und die Materialsteifigkeitsabminderung infolge Rissbildung, die zur Schädigung des Verbundwerkstoffs Beton führt, reduziert werden. Man konnte sehen, dass der Druckfestigkeitsabminderungsfaktor und insbesondere die zur maximal aufnehmbaren Zylinderdruckfestigkeit gehörende Stauchung, durch Zugabe von Stahlfasern besser begrenzt wird. Die experimentelle Untersuchungen wurden an sechs faserfreien und sieben stahlfaserverstärkten Stahlbetonscheiben unter Druck-Zugbelastung zur Bestimmung des Verhaltens des gerissenen faserfreien und stahlfaserverstärkten Stahlbetons durchgeführt. Die aus eigenen Versuchen ermittelten Materialeigenschaften des Betons, des stahlfaserverstärkten Betons und Stahlbetons im gerissenen Zustand wurden dargelegt und diskutiert. Bei der Rissbildung des quasi- spröden Werkstoffs Beton und dem stahlfaserverstärkten Beton wurde neben dem plastischen Fließen, auch die Abnahme des Elastizitätsmoduls festgestellt. Die Abminderung der aufnehmbaren Festigkeit und der zugehörigen Verzerrung lässt sich nicht mit der klassischen Fließtheorie der Plastizität ohne Modifizierung des Verfestigungsgesetzes erfassen. Es wurden auf elasto-plastischen Werkstoffmodellen basierende konstitutive Beziehungen für den faserfreien sowie den stahlfaserverstärkten Beton vorgeschlagen. Darüber hinaus wurde in der vorliegenden Arbeit eine auf dem elasto-plastischen Werkstoffmodell basierende konstitutive Beziehung für Beton und den stahlfaser-verstärkten Beton im gerissenen Zustand formuliert. Die formulierten Werkstoffmodelle wurden mittels dem in einer modularen Form aufgebauten nichtlinearen Finite Elemente Programm DIANA zu numerischen Untersuchungen an ausgewählten experimentell untersuchten Flächentragwerken, wie scheibenartigen-, plattenartigen- und Schalentragwerken aus faserfreiem sowie stahlfaserverstärktem Beton verwendet. Das entwickelte elasto-plastische Modell ermöglichte durch eine modifizierte effektive Spannungs-Verzerrungs-Beziehung für das Verfestigungsmodell, nicht nur die Erfassung des plastischen Fließens sondern auch die Berücksichtigung der Schädigung der Elastizitätsmodule infolge Mikrorissen sowie Makrorissen im Hauptzugspannungs-Hauptdruckspannungs-Bereich. Es wurde bei den numerischen Untersuchungen zur Ermittlung des Last-Verformungsverhaltens von scheibenartigen, plattenartigen- und Schalentragwerken aus faserfreiem und stahlfaserverstärktem Stahlbeton, im Vergleich mit den aus Versuchen ermittelten Ergebnissen, eine gute Übereinstimmung festgestellt.

Prevalencia de enfermedad celiaca en Latinoamérica: revisión sistemática de la literatura y meta-análisis

Introducción: La enfermedad celiaca (EC) es una enfermedad autoinmune (EA) intestinal desencadenada por la ingesta de gluten. Por la falta de información de la presencia de EC en Latinoamérica (LA), nosotros investigamos la prevalencia de la enfermedad en esta región utilizando una revisión sistemática de la literatura y un meta-análisis. Métodos y resultados: Este trabajo fue realizado en dos fases: La primera, fue un estudio de corte transversal de 300 individuos Colombianos. La segunda, fue una revisión sistemática y una meta-regresión siguiendo las guías PRSIMA. Nuestros resultados ponen de manifiesto una falta de anti-transglutaminasa tisular (tTG) e IgA anti-endomisio (EMA) en la población Colombiana. En la revisión sistemática, 72 artículos cumplían con los criterios de selección, la prevalencia estimada de EC en LA fue de 0,46% a 0,64%, mientras que la prevalencia en familiares de primer grado fue de 5,5 a 5,6%, y en los pacientes con diabetes mellitus tipo 1 fue de 4,6% a 8,7% Conclusión: Nuestro estudio muestra que la prevalencia de EC en pacientes sanos de LA es similar a la notificada en la población europea.

Endocarditis infecciosa por Staphylococcus Aureus Meticilino sensible y resistente en la Fundación Cardioinfantil – Instituto de Cardiología

Introducción y objetivos: La endocarditis infecciosa (EI) es una enfermedad grave producida por diversos gérmenes que afectan las válvulas cardiacas y el tejido endomiocárdico. El objetivo fue describir las características epidemiológicas, clínicas, ecocardiográficas y microbiológicas de la endocarditis infecciosa por Staphylococcus aureus (S. aureus) meticilino sensible y resistente de la Fundación Cardioinfantil – Instituto de Cardiología (FCI-IC) en el periodo de tiempo 2010- 2015. Métodos: Cohorte retrospectiva de casos de EI por S. aureus en la FCIIC para el período 2010-2015. Se realizó descripción de las variables generales de la población a estudio utilizando medidas de tendencia central y dispersión. Análisis de desenlaces teniendo cuenta la concentración inhibitoria mínima de vancomicina. Resultados: En el estudio se presentaron 27 casos de EI, con una mayor proporción de pacientes de sexo masculino, con hipertensión, diabetes y hemodiálisis. La fiebre fue la manifestación más frecuente seguida de fenómenos vasculares. La válvula más comprometida fue la mitral, principalmente nativa. Discusión: La presentación clínica de los pacientes con EI por S. aureus es aguda por lo que la fiebre es la principal manifestación clínica presentada, lo anterior favorece un rápido diagnóstico clínico. De las cepas de S. aureus causante de EI no se encontró gérmenes con sensibilidad intermedia ni resistente a la vancomicina según criterios establecidos por CLSI. Se encontró mayor proporción de pacientes con un valor de CMI para vancomicina mayor a 0,5μg/ml lo cual es importante dado que podemos estar enfrentándonos a cepas hetero VISA (hVISA).

Mapping the spatial distribution of geomorphological processes in the Okstindan area of northern Norway, using Geomorphic Process Units as derived from remote sensing and ground survey

The delineation of Geomorphic Process Units (GPUs) aims to quantify past, current and future geomorphological processes and the sediment flux associated with them. Five GPUs have been identified for the Okstindan area of northern Norway and these were derived from the combination of Landsat satellite imagery (TM and ETM+) with stereo aerial photographs (used to construct a Digital Elevation Model) and ground survey. The Okstindan study area is sub-arctic and mountainous and is dominated by glacial and periglacial processes. The GPUs exclude the glacial system (some 37% of the study area) and hence they are focussed upon periglacial and colluvial processes. The identified GPUs are: 1. solifluction and rill erosion; 2. talus creep, slope wash and rill erosion; 3. accumulation of debris by rock and boulder fall; 4. rockwalls; and 5. stable ground with dissolved transport. The GPUs have been applied to a ‘test site’ within the study area in order to illustrate their potential for mapping the spatial distribution of geomorphological processes. The test site within the study area is a catchment which is representative of the range of geomorphological processes identified.