Estudo da sinterização de cavacos de aço ferritico

This research studies the sintering of ferritic steel chips from the machining process. Were sintered metal powder obtained from machining process chips for face milling of a ferritic steel. The chip was produced by machining and characterized by SEM and EDS, and underwent a process of high energy mill powder characterized also by SEM and EDS. Were constructed three types of matrixes for uniaxial compression (relation l / d greater than 2.5). The differences in the design of the matrixes were essentially in the direction of load application, which for cylindrical case axial direction, while for the rectangular arrays, the longer side. Two samples were compressed with different geometries, a cylindrical and rectangular with the same compaction pressure of 700 MPa. The samples were sintered in a vacuum resistive furnace, heating rate 20 °C / min., isotherm 1300 °C for 60 minutes, and cooling rate of 25 °C / min to room temperature. The starting material of the rectangular sample was further annealed up to temperature of 800 ° C for 30 min. Sintered samples were characterized by scanning electron microscopy, optical microscopy and EDS. The sample compressed in the cylindrical matrix did not show a regular density reflecting in the sintered microstructure revealed by the irregular geometry of the pores, characterizing that the sintering was not complete, reaching only the second phase. As for the specimen compacted in the rectangular array, the analysis performed by scanning electron microscopy, optical microscopy and EDS indicate a good densification, and homogeneous microstructure in their full extent. Additionally, the EDS analyzes indicate no significant changes in chemical composition in the process steps. Therefore, it is concluded that recycling of chips, from the processed ferritic steel is feasible by the powder metallurgy. It makes possible rationalize raw material and energy by manufacture of known properties components from chips generated by the machining process, being benefits to the environment

Tratamentos de fibras de carnaúba [copernicia prunífera (miller) h. e. moore] para o desenvolvimento de compósito biodegradável com matriz de polihidroxibutirato

The use of raw materials from renewable sources for production of materials has been the subject of several studies and researches, because of its potential to substitute petrochemical-based materials. The addition of natural fibers to polymers represents an alternative in the partial or total replacement of glass fibers in composites. In this work, carnauba leaf fibers were used in the production of biodegradable composites with polyhydroxybutyrate (PHB) matrix. To improve the interfacial properties fiber / matrix were studied four chemical treatments to the fibers..The effect of the different chemical treatments on the morphological, physical, chemical and mechanical properties of the fibers and composites were investigated by scanning electron microscopy (SEM), infrared spectroscopy, X-ray diffraction, tensile and flexural tests, dynamic mechanical analysis (DMA), thermogravimetry (TGA) and diferential scanning calorimetry (DSC). The results of tensile tests indicated an increase in tensile strength of the composites after the chemical treatment of the fibers, with best results for the hydrogen peroxide treated fibers, even though the tensile strength of fibers was slightly reduced. This suggests a better interaction fiber/matrix which was also observed by SEM fractographs. The glass transition temperature (Tg) was reduced for all composites compared to the pure polymer which can be attributed to the absorption of solvents, moisture and other low molecular weight molecules by the fibers

[Concepto, definición, factores y matriz del empaque].

33 hojas.

Comportamento magnético de compósitos de matriz polimérica com adição de ferritas

Polymer matrix composites offer advantages for many applications due their combination of properties, which includes low density, high specific strength and modulus of elasticity and corrosion resistance. However, the application of non-destructive techniques using magnetic sensors for the evaluation these materials is not possible since the materials are non-magnetizable. Ferrites are materials with excellent magnetic properties, chemical stability and corrosion resistance. Due to these properties, these materials are promising for the development of polymer composites with magnetic properties. In this work, glass fiber / epoxy circular plates were produced with 10 wt% of cobalt or barium ferrite particles. The cobalt ferrite was synthesized by the Pechini method. The commercial barium ferrite was subjected to a milling process to study the effect of particle size on the magnetic properties of the material. The characterization of the ferrites was carried out by x-ray diffraction (XRD), field emission gun scanning electron microscopy (FEG-SEM) and vibrating sample magnetometry (VSM). Circular notches of 1, 5 and 10 mm diameter were introduced in the composite plates using a drill bit for the non-destructive evaluation by the technique of magnetic flux leakage (MFL). The results indicated that the magnetic signals measured in plates with barium ferrite without milling and cobalt ferrite showed good correlation with the presence of notches. The milling process for 12 h and 20 h did not contribute to improve the identification of smaller size notches (1 mm). However, the smaller particle size produced smoother magnetic curves, with fewer discontinuities and improved signal-to-noise ratio. In summary, the results suggest that the proposed approach has great potential for the detection of damage in polymer composites structures

Matriz Input-Output da região Alentejo: Acerca da Distribuição de Rendimento (3º quadrante)

No número 18 do “Boletim Trimestral” apresentámos os principais resultados do estudo que elaborou a Matriz Input-Output da Região Alentejo (MIO-Alentejo). Com este texto prosseguimos o propósito de divulgação dos resultados e conclusões do projeto, mas adotando agora uma perspectiva mais focalizada. Em particular, interessa-nos de momento olhar para o processo de formação do valor acrescentado, ou, de forma equivalente, para a distribuição do rendimento gerado na produção, sob a forma de remuneração dos diferentes fatores produtivos (3º quadrante). Nos pontos 2, 3, e 4 apresentamos os resultados e, em conclusão, deixamos algumas considerações finais no ponto 5. Anexamos um glossário com uma breve descrição metodológica.

O processo de transformação das Forças Armadas da Alemanha decorrentes da participação das missões internacionais entre 1992 – 2010

No fim da guerra fria, teve início uma nova era para a Bundeswehr. Com a participação em missões no estrangeiro, surgiram novos desafios que influenciaram as diretrizes da defesa, a estrutura da força, a orientação e as necessidades de formação das forças armadas alemãs. Entre 1992 e 2010, foram implementadas alterações profundas para lidar com a nova situação da NATO e da Alemanha na organização. Em 2003, após várias reformas, o ministério da defesa considerou que reformas apenas não eram suficientes, e teve início o chamado processo de transformação. Este processo contínuo influenciou a "face da Bundeswehr mais profundamente do que qualquer outra alteração até à altura. A orientação em missões internacionais era o novo objetivo e uma consequência de experiências na Somália, Bósnia, Kosovo e Afeganistão. Além disso, a crise financeira para as despesas da defesa e a mudança da estrutura da força NATO influenciaram a Bundeswehr de forma semelhante, e impulsionaram a política de defesa alemã também para estas novas direções. A nova Bundeswehr orientada para missões foram moldadas e desenvolvidas de forma diferente, transformação é a nova palavra-chave e este processo contínuo mantém-se até hoje. Abstract: After the end of the cold war a new era began for the Bundeswehr. With the participation in missions out of area, new challenges came up and influenced the defense papers, force structure, orientation and training needs of the German armed forces. Within 1992 and 2010 several far-reaching changes were made, to deal with the new situation of the NATO and Germanys role within the organization. In 2003, after various reforms, reforms only were no longer sufficient in the eyes of acting minister of defense and the so called transformations process was initiated. This continuing process influenced the “face” of the Bundeswehr more deeply than any other changes before. The orientation on out of area missions was the new objective and a consequence from experiences in Somalia, Bosnia, Kosovo and Afghanistan. Beside of that, the financial downturn for defense expenditure and the changing NATO force structure influenced the Bundeswehr in a similar way and pushed the German defense policy into new directions as well. The new mission orientated Bundeswehr was shaped and built up differently, transformation is the new leading word and the ongoing process until today.

Transformação urbana de uma área histórica

Tese de Doutoramento em Arquitetura com a especialização em Conservação e Reabilitação, apresentada na Faculdade de Arquitetura da Universidade de Lisboa, para obtenção do grau de Doutor.

Transformação direta de lamas primárias papeleiras em bioprodutos: um desafio à bioengenharia

Dissertação de Mestrado, Engenharia Biológica, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2014

Transformação de modelos ORM-UML

Dissertação de Mestrado, Engenharia Informática, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2014

Development of Locust Bean Gum Nanoparticles for protein delivery

Dissertação de Mestrado, Ciências Biomédicas, Departamento de Ciências Biomédicas e Medicina, Universidade do Algarve, 2014

Adaptação do questionário de suporte parental (QSP-6) - versão reduzida para adolescentes

"A família tem grande poder de influência e de transformação na vida de crianças e adolescentes. Os estudos recentes referem que o suporte familiar parece influenciar o desenvolvimento de comportamentos agressivos. Afirmam ainda a existência de uma relação entre o comportamento de bullying e o suporte que os jovens recebem das suas famílias. Assim, partindo da hipótese de que na fase da adolescência dos filhos, o suporte social dos pais poderá estar na origem de diferentes tipos de comportamentos agressivos/vitimizantes, o objetivo deste estudo é o de explorar as propriedades psicométricas do Questionário de Suporte Parental (QSP-6) – versão reduzida para Adolescentes (Clouse, 2007). Deste modo, apresentamos os resultados obtidos a partir de uma amostra de 728 adolescentes e jovens (372 do sexo feminino e 356 do sexo masculino) com idades compreendidas entre os 12 e os 21 anos. A estrutura relacional dos 18 itens foi avaliada por uma Análise Fatorial Exploratória (AFE) sobre a matriz de correlações, com extração dos fatores pelo método das componentes principais, seguido de rotação varimax. Os estudos psicométricos do QSP-6 revelam, de forma global, bons índices de fiabilidade e validade do instrumento."

Comportamento da adição do carbeto de nióbio (nBC) na matriz metálica do aço ferrítico 15kH2mfa

The 15Kh2MFA steel is a kind of Cr-Mo-V family steels and can be used in turbines for energy generation, pressure vessels, nuclear reactors or applications where the range of temperature that the material works is between 250 to 450°C. To improve the properties of these steels increasing the service temperature and the thermal stability is add a second particle phase. These particles can be oxides, carbides, nitrites or even solid solution of some chemical elements. On this way, this work aim to study the effect of addition of 3wt% of niobium carbide in the metallic matrix of 15Kh2MFA steel. Powder metallurgy was the route employed to produce this metallic matrix composite. Two different milling conditions were performed. Condition 1: milling of pure 15Kh2MFA steel and condition 2: milling of 15Kh2MFA steel with addition of niobium carbide. A high energy milling was carried out during 5 hours. Then, these two powders were sintered in a vacuum furnace (10-4torr) at 1150 and 1250°C during 60 minutes. After sintering the samples were normalized at 950°C per 3 minutes followed by air cooling to obtain a desired microstructure. Results show that the addition of niobium carbide helps to mill faster the particles during the milling when compared with that steel without carbide. At the sintering, the niobium carbide helps to sinter increasing the density of the samples reaching a maximum density of 7.86g/cm³, better than the melted steel as received that was 7,81g/cm³. In spite this good densification, after normalizing, the niobium carbide don t contributed to increase the microhardness. The best microhardness obtained to the steel with niobium carbide was 156HV and to pure 15Kh2MFA steel was 212HV. It happened due when the niobium carbide is added to the steel a pearlitic structure was formed, and the steel without niobium carbide submitted to the same conditions reached a bainitic structure

Reguladores da expressão do gene da proteía Gla da matriz (MGP) numa linha celular derivada de peixe

Dissertação de mest. em Biotecnologia, Faculdade de Engenharia de Recursos Naturais, Univ. do Algarve, 2004

Paisagens industriais em transformação. Reconversão da área envolvente da antiga fábrica de óleo de fígado de bacalhau em espaço público, Cais do Ginjal, Almada

Mestrado em Arquitetura Paisagista - Instituto Superior de Agronomia - UL

Estudo da adição de resíduo de scheelita em matriz cerâmica: formulação, propriedades físicas e microestrutura

Extractivism mineral is considered an activity highly degrading, due to the large volume of material that he moves in the form of ore and residues. The vast majority of mining companies do not show any technology or economically viable application that will allow the recycling of mineral residue, these being launched in areas receiving located the "open skies" degrade the environment. In Rio Grande do Norte to the production of ceramic red restricts their activities to the production of products such as: solid bricks, ceramic blocks, tiles, among others. Seeking to unite experiences and technical information that favor sustainable development, with important benefits to the construction sector and civil society in general, the present work studies the incorporation of the residue of scheelite in ceramic matrix kaolinitic, coming from the municipality of Boa Saúde - RN, in percentage of 5 %, 10 %, 20 %, 30% 40% and 50 %, by evaluating its microstructure, physical properties and formulation. The raw materials were characterized through the trials of X ray fluorescence, Diffraction of X rays, Differential Thermal Analysis and Termogravimetric Analysis. The samples were formed and fired at temperatures of 850o, 900o, 1000o, 1050o, 1100o, 1150o and 1200 oC, with isotherm of 1 hour and heating rate of 10 oC/min. Assays were performed technological of loss to fire, Water Absorption, Apparent Porosity, Apparent Density, Mass Loss in Fire and Bending Resistance; in addition to the Scanning Electron Microscopy, analyzing their physical and mechanical properties. The use of residue of scheelite in ceramic mass kaolinitic provided a final product with technological properties that meet the technical standards for the production of bricks and roofing tiles, with the percentage of 20% of waste that showed the best results