Qualidade e alterações estruturais do café arábica submetido a alternância da temperatura na secagem

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Otimização de sistemas de distribuição de energia elétrica radiais usando programação cônica de segunda ordem inteira mista

Pós-graduação em Engenharia Elétrica - FEIS

Energia mecânica, energia térmica e moagem na extrusão de alimentos para cães e gatos

Pós-graduação em Medicina Veterinária - FCAV

Seleção, avaliação e utilização de uma levedura personalizada para a produção de etanol

Pós-graduação em Microbiologia - IBILCE

Electropolymerization using binuclear nickel(II) Schiff base complexes bearing N4O4 donors as supramolecular building blocks

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Modeling of hydraulic and energy efficiency indicators for water supply systems

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Energetic exploitation from a hybrid PV-wind power micro-generation rural electrification

Hybrid system micro-generation integration of PV-wind power is presented by a form of energy in which problems resulting from variability in the intensity of wind and solar intensity are possible mitigation either by complementation between one source to another or the largest stability configured by the generate the system. Based on this context, this work aims to assessing the performance of a hybrid system PV-wind power energy small of a rural property for their electrification. The study has been developed at the Rural Laboratory Powering from Engineering Department of UNESP. In order to present this research, a hybrid system has been installed PV-wind power, composed of one 400Wp windmill and a 300 Wp PV-system. The results obtained allowed us to evaluate the solar and wind energy supplied ranked among 285 and 360 kWh electric power generated by the PV-wind power hybrid system stood between 25,5 and 31 kWh. At is to say achieving yield of approximately than 10% during one year observation period, i.e., it was concluded that the performance of the hybrid system depended essentially the energy received and generated by the PV-system and that there was complementation between generating wind power and PV-systems with regard to time of day and the annual seasons by confirming the technical feasibility of this kind system of micro-generation in small rural properties.

Numerical tests of an adaptive sectioned airfoil actuated by shape memory alloys

The main objective of this work is to illustrate an application of angular active control in a sectioned airfoil using shape memory alloys. In the proposed model, one wants to establish the shape of the airfoil profile based on the determination of an angle between its two sections. This angle is obtained by the effect of the shape memory of the alloy by passing an electric current that modifies the temperature of the wire through the Joule effect, changing the shape of the alloy. This material is capable of converting thermal energy into mechanical energy and once permanently deformed, the material can return to its original shape by heating. Due to the presence of nonlinear effects, especially in the mathematical model of the alloy, this work proposes the application of a control system based on fuzzy logic. Through numerical tests, the performance of the fuzzy controller is compared with an on-off controller applied in a sectioned airfoil model.

Abrasion resistance of direct and indirect resins as a function of a sealant veneer

Abrasive wear is one of the most common type of wear that not only affect teeth, as also dental restorations. Thus to investigate one of the etiological factors as tooth brushing procedure is clinical relevant in order to select the best material combination that may prevent damage of resin dental restoration's abrasion. This study evaluated the influence of tooth brushing on mass loss and surface roughness of direct Venus (Vs) and indirect Signum (Sg) resin composites, with and without a surface sealant, Fortify (F). Twenty-four specimens were prepared with each resin composite, using their proprietary curing units, according to manufacturer's instructions. All the specimens were polished and ultrasonically cleaned in distilled water for 5 minutes. Half of the specimens of each resin (n = 12) were covered with F (Vs F and Sg F ), except for the control (C) specimens (Vs C and Sg C ), which were not sealed. Mass loss (ML) as well as surface roughness (Ra ) was measured for all the specimens. Then, the specimens were subjected to toothbrush-dentifrice abrasion, using a testing machine for 67.000 brushing strokes, in an abrasive slurry. After brushing simulation, the specimens were removed from the holder, rinsed thoroughly and blot dried with soft absorbent paper. The abrasion of the material was quantitatively determined with final measurements of ML and surface roughness, using the method described above. ML data were analyzed by two-way analysis of variance (ANOVA) and the analysis indicated that resin composites were not statistically different; however, the specimens sealed with F showed higher ML. Ra mean values of the groups Vs F and Sg F significantly increased. Tooth brushing affects mainly the roughness of the direct and indirect resin composites veneered with a sealant.

Evaluation of femur of orchiectomized guinea pigs by bone densitometry using dual-energy x-ray absortiometry (DXA) and mechanical testing

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Compensação ativa paralela baseada na teoria de potência conservativa

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Eficiência de um sistema de desinfecção solar de águas residuárias domésticas com adição de diferentes doses de peróxido de hidrogênio

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA

Desenvolvimento de um sistema de controle para avaliação de fontes de energias renováveis no bombeamento de água

The use of alternative energy systems in the current days is an urgent necessity due to the problems that the planet is facing as the heating and loss of ozone layer. The scarcity of conventional energy is another problem that must be solved for the future of humanity. It must be considered that the people are inhabiting places moved away not always with available energy. The application of technologies as automation and control can help us to solve this problem. Therefore, this work aimed at apply an equipment of industrial usage, the Programmable Logical Controller, PLC, in alternative energies systems, as eolic generation and fotovoltaic generation used for water pumping, aiming the automatic control and the efficiency in the places where it has simultaneous availability of these sources, based in criterion of priority that previously established itself between them. It was made a hydraulic and energetic evaluation of the energy system, eolic and fotovoltaic, used in the automatic control system of pumping, in the place of accomplishment of the experiment, according to previously established physical conditions. The results have shown that the control system using the PLC is practicable and has trustworthiness. The program developed can be adapted for the use with several power plants in a specific application place. The fotovoltaic system of pumping, using a polycrystalline of 70 Watts connected to a pump Shurflo 8000, showed to be efficient with significant flows in almost all the months. The eolic system of pumping, using an eolic generator of 400 Watts assembled in place of experiment, did not demonstrate energetic capacity for use in this specific type of application.

Síntese e caracterização de hidrogéis nanoestruturados contendo nanoargila e zeólita com potencialidade de aplicação em sistemas de liberação controlada de fármacos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Avaliação da bioatividade de revestimentos produzidos sobre Tântalo por oxidação eletrolítica assistida por plasma

Pós-graduação em Ciência e Tecnologia de Materiais - FC