Development and implementation of an integrated technical management system

Quality Management, Integrated Technical Management Systems, ITMS, Technical Elements, Environment, Occupational Health and safety, OH&S, Standards, ISO, General Regulations, Integration, Management Functions, Computer Centre, Suc-cess Concepts, Documentation, PCT, QMS, EMS, OH&S-MS, Portioning, Evaluation, Technical Cycle, Technical Compliance, Framework

In-vitro cell exposure studies for the assessment of nanoparticle toxicity in the lung: a dialog between aerosol science and biology

The introduction of engineered nanostructured materials into a rapidly increasing number of industrial and consumer products will result in enhanced exposure to engineered nanoparticles. Workplace exposure has been identified as the most likely source of uncontrolled inhalation of engineered aerosolized nanoparticles, but release of engineered nanoparticles may occur at any stage of the lifecycle of (consumer) products. The dynamic development of nanomaterials with possibly unknown toxicological effects poses a challenge for the assessment of nanoparticle induced toxicity and safety.In this consensus document from a workshop on in-vitro cell systems for nanoparticle toxicity testing11Workshop on 'In-Vitro Exposure Studies for Toxicity Testing of Engineered Nanoparticles' sponsored by the Association for Aerosol Research (GAeF), 5-6 September 2009, Karlsruhe, Germany. an overview is given of the main issues concerning exposure to airborne nanoparticles, lung physiology, biological mechanisms of (adverse) action, in-vitro cell exposure systems, realistic tissue doses, risk assessment and social aspects of nanotechnology. The workshop participants recognized the large potential of in-vitro cell exposure systems for reliable, high-throughput screening of nanoparticle toxicity. For the investigation of lung toxicity, a strong preference was expressed for air-liquid interface (ALI) cell exposure systems (rather than submerged cell exposure systems) as they more closely resemble in-vivo conditions in the lungs and they allow for unaltered and dosimetrically accurate delivery of aerosolized nanoparticles to the cells. An important aspect, which is frequently overlooked, is the comparison of typically used in-vitro dose levels with realistic in-vivo nanoparticle doses in the lung. If we consider average ambient urban exposure and occupational exposure at 5mg/m3 (maximum level allowed by Occupational Safety and Health Administration (OSHA)) as the boundaries of human exposure, the corresponding upper-limit range of nanoparticle flux delivered to the lung tissue is 3×10-5-5×10-3μg/h/cm2 of lung tissue and 2-300particles/h/(epithelial) cell. This range can be easily matched and even exceeded by almost all currently available cell exposure systems.The consensus statement includes a set of recommendations for conducting in-vitro cell exposure studies with pulmonary cell systems and identifies urgent needs for future development. As these issues are crucial for the introduction of safe nanomaterials into the marketplace and the living environment, they deserve more attention and more interaction between biologists and aerosol scientists. The members of the workshop believe that further advances in in-vitro cell exposure studies would be greatly facilitated by a more active role of the aerosol scientists. The technical know-how for developing and running ALI in-vitro exposure systems is available in the aerosol community and at the same time biologists/toxicologists are required for proper assessment of the biological impact of nanoparticles.

Sickness presenteeism in Spanish-born and immigrant workers in Spain

Background: Previous studies have shown that immigrant workers face relatively worse working and employment conditions, as well as lower rates of sickness absence than native-born workers. This study aims to assess rates of sickness presenteeism in a sample of Spanish-born and foreign-born workers according to different characteristics. Methods: A cross-sectional survey was conducted amongst a convenience sample of workers (Spanish-born and foreign-born), living in four Spanish cities: Barcelona, Huelva, Madrid and Valencia (2008-2009). Sickness presenteeism information was collected through two items in the questionnaire ("Have you had health problems in the last year?" and "Have you ever had to miss work for any health problem?") and was defined as worker who had a health problem (answered yes, first item) and had not missed work (answered no, second item). For the analysis, the sample of 2,059 workers (1,617 foreign-born) who answered yes to health problems was included. After descriptives, logistic regressions were used to establish the association between origin country and sickness presenteeism (adjusted odds ratios aOR; 95% confidence interval 95%CI). Analyses were stratified per time spent in Spain among foreign-born workers. Results: All of the results refer to the comparison between foreign-born and Spanish-born workers as a whole, and in some categories relating to personal and occupational conditions. Foreign-born workers were more likely to report sickness presenteeism compared with their Spanish-born counterparts, especially those living in Spain for under 2 years [Prevalence: 42% in Spanish-born and 56.3% in Foreign-born; aOR 1.77 95%CI 1.24-2.53]. In case of foreign-born workers (with time in Spain < 2 years), men [aOR 2.31 95%CI 1.40-3.80], those with university studies [aOR 3.01 95%CI 1.04-8.69], temporary contracts [aOR 2.26 95%CI 1.29-3.98] and salaries between 751-1,200€ per month [aOR 1.74 95% CI 1.04-2.92] were more likely to report sickness presenteeism. Also, recent immigrants with good self-perceived health and good mental health were more likely to report presenteeism than Spanish-born workers with the same good health indicators. Conclusions: Immigrant workers report more sickness presenteeism than their Spanish-born counterparts. These results could be related to precarious work and employment conditions of immigrants. Immigrant workers should benefit from the same standards of social security, and of health and safety in the workplace that are enjoyed by Spanish workers.

Offshore work and the work of nurses on board: an integrative review

OBJECTIVETo know the production of theoretical approaches on issues related to offshore work and the work of offshore nurses.METHODIntegrative literature review conducted in the databases of LILACS, BDENF, MEDLINE, SciELO and Index PSI.RESULTSWe selected 33 studies published in national and international journals between 1997 and 2014. The thematic analysis corpus resulted in four central themes: offshore work environment; amid work adversities, an escape; structuring of offshore health and safety services; in search of safe practices.CONCLUSIONThis study contributes to the offshore work of nurses in relation to the nature of work, acting amid adversities and the restless search for safe practices in the open sea.

Management of nanomaterials safety in research environment

Despite numerous discussions, workshops, reviews and reports about responsible development of nanotechnology, information describing health and environmental risk of engineered nanoparticles or nanomaterials is severely lacking and thus insufficient for completing rigorous risk assessment on their use. However, since preliminary scientific evaluations indicate that there are reasonable suspicions that activities involving nanomaterials might have damaging effects on human health; the precautionary principle must be applied. Public and private institutions as well as industries have the duty to adopt preventive and protective measures proportionate to the risk intensity and the desired level of protection. In this work, we present a practical, 'user-friendly' procedure for a university-wide safety and health management of nanomaterials, developed as a multi-stakeholder effort (government, accident insurance, researchers and experts for occupational safety and health). The process starts using a schematic decision tree that allows classifying the nano laboratory into three hazard classes similar to a control banding approach (from Nano 3 - highest hazard to Nano1 - lowest hazard). Classifying laboratories into risk classes would require considering actual or potential exposure to the nanomaterial as well as statistical data on health effects of exposure. Due to the fact that these data (as well as exposure limits for each individual material) are not available, risk classes could not be determined. For each hazard level we then provide a list of required risk mitigation measures (technical, organizational and personal). The target 'users' of this safety and health methodology are researchers and safety officers. They can rapidly access the precautionary hazard class of their activities and the corresponding adequate safety and health measures. We succeed in convincing scientist dealing with nano-activities that adequate safety measures and management are promoting innovation and discoveries by ensuring them a safe environment even in the case of very novel products. The proposed measures are not considered as constraints but as a support to their research. This methodology is being implemented at the Ecole Polytechnique de Lausanne in over 100 research labs dealing with nanomaterials. It is our opinion that it would be useful to other research and academia institutions as well. [Authors]

Assessment of the occurrence of nanoparticles in Swiss industry and evaluation of the appropriatenesss of the measurement devices to determine the workforce exposure

Abstract : The occupational health risk involved with handling nanoparticles is the probability that a worker will experience an adverse health effect: this is calculated as a function of the worker's exposure relative to the potential biological hazard of the material. Addressing the risks of nanoparticles requires therefore knowledge on occupational exposure and the release of nanoparticles into the environment as well as toxicological data. However, information on exposure is currently not systematically collected; therefore this risk assessment lacks quantitative data. This thesis aimed at, first creating the fundamental data necessary for a quantitative assessment and, second, evaluating methods to measure the occupational nanoparticle exposure. The first goal was to determine what is being used where in Swiss industries. This was followed by an evaluation of the adequacy of existing measurement methods to assess workplace nanopaiticle exposure to complex size distributions and concentration gradients. The study was conceived as a series of methodological evaluations aimed at better understanding nanoparticle measurement devices and methods. lt focused on inhalation exposure to airborne particles, as respiration is considered to be the most important entrance pathway for nanoparticles in the body in terms of risk. The targeted survey (pilot study) was conducted as a feasibility study for a later nationwide survey on the handling of nanoparticles and the applications of specific protection means in industry. The study consisted of targeted phone interviews with health and safety officers of Swiss companies that were believed to use or produce nanoparticles. This was followed by a representative survey on the level of nanoparticle usage in Switzerland. lt was designed based on the results of the pilot study. The study was conducted among a representative selection of clients of the Swiss National Accident Insurance Fund (SUVA), covering about 85% of Swiss production companies. The third part of this thesis focused on the methods to measure nanoparticles. Several pre- studies were conducted studying the limits of commonly used measurement devices in the presence of nanoparticle agglomerates, This focus was chosen, because several discussions with users and producers of the measurement devices raised questions about their accuracy measuring nanoparticle agglomerates and because, at the same time, the two survey studies revealed that such powders are frequently used in industry. The first preparatory experiment focused on the accuracy of the scanning mobility particle sizer (SMPS), which showed an improbable size distribution when measuring powders of nanoparticle agglomerates. Furthermore, the thesis includes a series of smaller experiments that took a closer look at problems encountered with other measurement devices in the presence of nanoparticle agglomerates: condensation particle counters (CPC), portable aerosol spectrometer (PAS) a device to estimate the aerodynamic diameter, as well as diffusion size classifiers. Some initial feasibility tests for the efficiency of filter based sampling and subsequent counting of carbon nanotubes (CNT) were conducted last. The pilot study provided a detailed picture of the types and amounts of nanoparticles used and the knowledge of the health and safety experts in the companies. Considerable maximal quantities (> l'000 kg/year per company) of Ag, Al-Ox, Fe-Ox, SiO2, TiO2, and ZnO (mainly first generation particles) were declared by the contacted Swiss companies, The median quantity of handled nanoparticles, however, was 100 kg/year. The representative survey was conducted by contacting by post mail a representative selection of l '626 SUVA-clients (Swiss Accident Insurance Fund). It allowed estimation of the number of companies and workers dealing with nanoparticles in Switzerland. The extrapolation from the surveyed companies to all companies of the Swiss production sector suggested that l'309 workers (95%-confidence interval l'073 to l'545) of the Swiss production sector are potentially exposed to nanoparticles in 586 companies (145 to l'027). These numbers correspond to 0.08% (0.06% to 0.09%) of all workers and to 0.6% (0.2% to 1.1%) of companies in the Swiss production sector. To measure airborne concentrations of sub micrometre-sized particles, a few well known methods exist. However, it was unclear how well the different instruments perform in the presence of the often quite large agglomerates of nanostructured materials. The evaluation of devices and methods focused on nanoparticle agglomerate powders. lt allowed the identification of the following potential sources of inaccurate measurements at workplaces with considerable high concentrations of airborne agglomerates: - A standard SMPS showed bi-modal particle size distributions when measuring large nanoparticle agglomerates. - Differences in the range of a factor of a thousand were shown between diffusion size classifiers and CPC/SMPS. - The comparison between CPC/SMPS and portable aerosol Spectrometer (PAS) was much better, but depending on the concentration, size or type of the powders measured, the differences were still of a high order of magnitude - Specific difficulties and uncertainties in the assessment of workplaces were identified: the background particles can interact with particles created by a process, which make the handling of background concentration difficult. - Electric motors produce high numbers of nanoparticles and confound the measurement of the process-related exposure. Conclusion: The surveys showed that nanoparticles applications exist in many industrial sectors in Switzerland and that some companies already use high quantities of them. The representative survey demonstrated a low prevalence of nanoparticle usage in most branches of the Swiss industry and led to the conclusion that the introduction of applications using nanoparticles (especially outside industrial chemistry) is only beginning. Even though the number of potentially exposed workers was reportedly rather small, it nevertheless underscores the need for exposure assessments. Understanding exposure and how to measure it correctly is very important because the potential health effects of nanornaterials are not yet fully understood. The evaluation showed that many devices and methods of measuring nanoparticles need to be validated for nanoparticles agglomerates before large exposure assessment studies can begin. Zusammenfassung : Das Gesundheitsrisiko von Nanopartikel am Arbeitsplatz ist die Wahrscheinlichkeit dass ein Arbeitnehmer einen möglichen Gesundheitsschaden erleidet wenn er diesem Stoff ausgesetzt ist: sie wird gewöhnlich als Produkt von Schaden mal Exposition gerechnet. Für eine gründliche Abklärung möglicher Risiken von Nanomaterialien müssen also auf der einen Seite Informationen über die Freisetzung von solchen Materialien in die Umwelt vorhanden sein und auf der anderen Seite solche über die Exposition von Arbeitnehmenden. Viele dieser Informationen werden heute noch nicht systematisch gesarnmelt und felilen daher für Risikoanalysen, Die Doktorarbeit hatte als Ziel, die Grundlagen zu schaffen für eine quantitative Schatzung der Exposition gegenüber Nanopartikel am Arbeitsplatz und die Methoden zu evaluieren die zur Messung einer solchen Exposition nötig sind. Die Studie sollte untersuchen, in welchem Ausmass Nanopartikel bereits in der Schweizer Industrie eingesetzt werden, wie viele Arbeitnehrner damit potentiel] in Kontakt komrrien ob die Messtechnologie für die nötigen Arbeitsplatzbelastungsmessungen bereits genügt, Die Studie folcussierte dabei auf Exposition gegenüber luftgetragenen Partikel, weil die Atmung als Haupteintrittspforte iïlr Partikel in den Körper angesehen wird. Die Doktorarbeit besteht baut auf drei Phasen auf eine qualitative Umfrage (Pilotstudie), eine repräsentative, schweizerische Umfrage und mehrere technische Stndien welche dem spezitischen Verständnis der Mëglichkeiten und Grenzen einzelner Messgeräte und - teclmikeri dienen. Die qualitative Telephonumfrage wurde durchgeführt als Vorstudie zu einer nationalen und repräsentativen Umfrage in der Schweizer Industrie. Sie zielte auf Informationen ab zum Vorkommen von Nanopartikeln, und den angewendeten Schutzmassnahmen. Die Studie bestand aus gezielten Telefoninterviews mit Arbeit- und Gesundheitsfachpersonen von Schweizer Unternehmen. Die Untemehmen wurden aufgrund von offentlich zugànglichen lnformationen ausgewählt die darauf hinwiesen, dass sie mit Nanopartikeln umgehen. Der zweite Teil der Dolctorarbeit war die repräsentative Studie zur Evalniernng der Verbreitnng von Nanopaitikelanwendungen in der Schweizer lndustrie. Die Studie baute auf lnformationen der Pilotstudie auf und wurde mit einer repräsentativen Selektion von Firmen der Schweizerischen Unfall Versicherungsanstalt (SUVA) durchgeüihxt. Die Mehrheit der Schweizerischen Unternehmen im lndustrieselctor wurde damit abgedeckt. Der dritte Teil der Doktorarbeit fokussierte auf die Methodik zur Messung von Nanopartikeln. Mehrere Vorstudien wurden dnrchgefîihrt, um die Grenzen von oft eingesetzten Nanopartikelmessgeräten auszuloten, wenn sie grösseren Mengen von Nanopartikel Agglomeraten ausgesetzt messen sollen. Dieser F okns wurde ans zwei Gründen gewählt: weil mehrere Dislcussionen rnit Anwendem und auch dem Produzent der Messgeràte dort eine Schwachstelle vermuten liessen, welche Zweifel an der Genauigkeit der Messgeräte aufkommen liessen und weil in den zwei Umfragestudien ein häufiges Vorkommen von solchen Nanopartikel-Agglomeraten aufgezeigt wurde. i Als erstes widmete sich eine Vorstndie der Genauigkeit des Scanning Mobility Particle Sizer (SMPS). Dieses Messgerät zeigte in Präsenz von Nanopartikel Agglorneraten unsinnige bimodale Partikelgrössenverteilung an. Eine Serie von kurzen Experimenten folgte, welche sich auf andere Messgeräte und deren Probleme beim Messen von Nanopartikel-Agglomeraten konzentrierten. Der Condensation Particle Counter (CPC), der portable aerosol spectrometer (PAS), ein Gerät zur Schàtzung des aerodynamischen Durchniessers von Teilchen, sowie der Diffusion Size Classifier wurden getestet. Einige erste Machbarkeitstests zur Ermittlnng der Effizienz von tilterbasierter Messung von luftgetragenen Carbon Nanotubes (CNT) wnrden als letztes durchgeiührt. Die Pilotstudie hat ein detailliiertes Bild der Typen und Mengen von genutzten Nanopartikel in Schweizer Unternehmen geliefert, und hat den Stand des Wissens der interviewten Gesundheitsschntz und Sicherheitsfachleute aufgezeigt. Folgende Typen von Nanopaitikeln wurden von den kontaktierten Firmen als Maximalmengen angegeben (> 1'000 kg pro Jahr / Unternehrnen): Ag, Al-Ox, Fe-Ox, SiO2, TiO2, und ZnO (hauptsächlich Nanopartikel der ersten Generation). Die Quantitäten von eingesetzten Nanopartikeln waren stark verschieden mit einem ein Median von 100 kg pro Jahr. ln der quantitativen Fragebogenstudie wurden l'626 Unternehmen brieflich kontaktiert; allesamt Klienten der Schweizerischen Unfallversicherringsanstalt (SUVA). Die Resultate der Umfrage erlaubten eine Abschätzung der Anzahl von Unternehmen und Arbeiter, welche Nanopartikel in der Schweiz anwenden. Die Hochrechnung auf den Schweizer lndnstriesektor hat folgendes Bild ergeben: ln 586 Unternehmen (95% Vertrauensintervallz 145 bis 1'027 Unternehmen) sind 1'309 Arbeiter potentiell gegenüber Nanopartikel exponiert (95%-Vl: l'073 bis l'545). Diese Zahlen stehen für 0.6% der Schweizer Unternehmen (95%-Vl: 0.2% bis 1.1%) und 0.08% der Arbeiternehmerschaft (95%-V1: 0.06% bis 0.09%). Es gibt einige gut etablierte Technologien um die Luftkonzentration von Submikrometerpartikel zu messen. Es besteht jedoch Zweifel daran, inwiefern sich diese Technologien auch für die Messurrg von künstlich hergestellten Nanopartikeln verwenden lassen. Aus diesem Grund folcussierten die vorbereitenden Studien für die Arbeitsplatzbeurteilnngen auf die Messung von Pulverri, welche Nan0partike1-Agg10merate enthalten. Sie erlaubten die ldentifikation folgender rnöglicher Quellen von fehlerhaften Messungen an Arbeitsplätzen mit erhöhter Luft-K0nzentrati0n von Nanopartikel Agglomeratenz - Ein Standard SMPS zeigte eine unglaubwürdige bimodale Partikelgrössenverteilung wenn er grössere Nan0par'til<e1Agg10merate gemessen hat. - Grosse Unterschiede im Bereich von Faktor tausend wurden festgestellt zwischen einem Diffusion Size Classiîier und einigen CPC (beziehungsweise dem SMPS). - Die Unterschiede zwischen CPC/SMPS und dem PAS waren geringer, aber abhängig von Grosse oder Typ des gemessenen Pulvers waren sie dennoch in der Grössenordnung von einer guten Grössenordnung. - Spezifische Schwierigkeiten und Unsicherheiten im Bereich von Arbeitsplatzmessungen wurden identitiziert: Hintergrundpartikel können mit Partikeln interagieren die während einem Arbeitsprozess freigesetzt werden. Solche Interaktionen erschweren eine korrekte Einbettung der Hintergrunds-Partikel-Konzentration in die Messdaten. - Elektromotoren produzieren grosse Mengen von Nanopartikeln und können so die Messung der prozessbezogenen Exposition stören. Fazit: Die Umfragen zeigten, dass Nanopartikel bereits Realitàt sind in der Schweizer Industrie und dass einige Unternehmen bereits grosse Mengen davon einsetzen. Die repräsentative Umfrage hat diese explosive Nachricht jedoch etwas moderiert, indem sie aufgezeigt hat, dass die Zahl der Unternehmen in der gesamtschweizerischen Industrie relativ gering ist. In den meisten Branchen (vor allem ausserhalb der Chemischen Industrie) wurden wenig oder keine Anwendungen gefunden, was schliessen last, dass die Einführung dieser neuen Technologie erst am Anfang einer Entwicklung steht. Auch wenn die Zahl der potentiell exponierten Arbeiter immer noch relativ gering ist, so unterstreicht die Studie dennoch die Notwendigkeit von Expositionsmessungen an diesen Arbeitsplätzen. Kenntnisse um die Exposition und das Wissen, wie solche Exposition korrekt zu messen, sind sehr wichtig, vor allem weil die möglichen Auswirkungen auf die Gesundheit noch nicht völlig verstanden sind. Die Evaluation einiger Geräte und Methoden zeigte jedoch, dass hier noch Nachholbedarf herrscht. Bevor grössere Mess-Studien durgefîihrt werden können, müssen die Geräte und Methodem für den Einsatz mit Nanopartikel-Agglomeraten validiert werden.

Beliefs and practices in the assessment of workplace pollutants

OBJECTIVES: A survey was undertaken among Swiss occupational hygienists and other professionals to identify the different exposure assessment methods used, the contextual parameters observed and the uses, difficulties and possible developments of exposure models for field application. METHODS: A questionnaire was mailed to 121 occupational hygienists, all members of the Swiss Occupational Hygiene Society. A shorter questionnaire was also sent to registered occupational physicians and selected safety specialists. Descriptive statistics and multivariate analyses were performed. RESULTS: The response rate for occupational hygienists was 60%. The so-called expert judgement appeared to be the most widely used method, but its efficiency and reliability were both judged with very low scores. Long-term sampling was perceived as the most efficient and reliable method. Various determinants of exposure, such as emission rate and work activity, were often considered important, even though they were not included in the exposure assessment processes. Near field local phenomena determinants were also judged important for operator exposure estimation. CONCLUSION: Exposure models should be improved to integrate factors which are more easily accessible to practitioners. Descriptors of emission and local phenomena should also be included.

Farm Safety is Important in Iowa, October 11, 2012

An IDPH Occupational Health and Safety Surveillance Program (OHSSP) analysis of Iowa’s work-related traumatic fatalities shows that transportation events accounted for 48 of 90 deaths in 2011. Agricultural activities were involved in 21 of the 48 transportation deaths (44%) and 32 of the 90 total fatalities (36%). Tractor and ATV (all-terrain vehicle) or UTV (utility vehicle) rollovers were responsible for 62% (13/21) of the farm or ag-related transportation deaths.

Practical Solutions for Increased Safety in Paper Mill Operations

Tämä diplomityö käsittelee työterveys- ja työturvallisuushallinnan (TTT) sekä ympäristönsuojelun ongelmia ja riskejä, joita tehdasalueen toiminnanharjoittaja kohtaa ulkoistaessaan tehdastoimintojaan ja siirtyessään käyttämään 24 h ulkoisia kunnossapitopalveluja. Teoriaosa selventää ulkoistukseen liittyviä lainmukaisia määräyksiä ja vaatimuksia koskien terveyden, turvallisuuden ja ympäristöongelmien hallintaa sellu-, paperi- ja kartonkitehtaissa Euroopassa, Yhdysvalloissa ja Suomessa. TTT-toiminnan tason sekä ympäristönsuojelun tason mittaamisen ongelmat tuodaan esille. Olemassa olevia kansainvälisiä TTT-johtamisjärjestelmien ja ympäristöjärjestelmien standardeja, riskien hallintatyökaluja ja ohjelmia esitellään lyhyesti. Käytännön osa toteutettiin tapaustutkimuksena, jonka kohteena oli Äänekosken tehdaskombinaatti ja kemianteollisuuden laitos, Noviant CMC Oy. TTT-hallintatoimien ja ympäristönsuojelun ongelmia tutkitaan tehdastoimintoja ulkoistettaessa. Integroidun johtamisjärjestelmän auditointimenettelyt, ulkoistuksen kohdealueet, pk-yrityksien riskien hallinta ja ulkoisten työntekijöiden turvallisuuskoulutus ovat erityisen tarkastelun alla. Käyttäen hyväksi kerättyä TTT- ja ympäristöaineistoa, suunniteltiin malli ja sisältöehdotus uudelle internet-selain tyyppiselle työkalulle TTT- ja ympäristöasioiden hallinnan avuksi. Työkalu on tarkoitettu palvelemaan Noviant CMC Oy:n eri sidosryhmien tarpeita. Diplomityön käytännön osa muodostaa pohjan JP MILLSAFE - pilottiprojektille, joka käynnistettiin internet-selain tyyppisen turvallisuuspalvelusovelluksen kehittämiseksi palvelemaan Äänekosken tehdaskombinaatin eri sidosryhmien tarpeita.

Transnational private authority, regulatory space and workers' collective competences: Bringing local contexts and worker agency back in

The impact of transnational private regulation on labour standards remains in dispute. While studies have provided some limited evidence of positive effects on 'outcome standards' such as wages or occupational health and safety, the literature gives little reason to believe that there has been any significant effect on 'process rights' relating primarily to collective workers' voice and social dialogue. This paper probes this assumption by bringing local contexts and worker agency more fully into the picture. It outlines an analytical framework that emphasizes workers' potential to act collectively for change in the regulatory space surrounding the employment relationship. It argues that while transnational private regulation on labour standards may marginally improve workers access to regulatory spaces and their capacity to require the inclusion of enterprises in them, it does little to increase union leverage. The findings are based on empirical research work conducted in Sub-Saharan Africa.

Safety and sustainability research for university schools of fine arts

Designing new teaching programs for both undergraduate and graduate university studies involves integrating concepts and methodologies regarding quality, work safety and hazard prevention, and environmental protection. One of the challenges facing Spanish research within the realm of European Higher Education concerns health and safety issues in the Arts.In the case of Fine Arts, student exploration is one of the fundamental pillars of the study program; therefore it is imperative that art studios be optimized. This optimization affects both designated resources (infrastructures, materials, equipment, etc.) and organization of the teaching force.In this context, the aim of our research is to improve educational practices by designing quality measures that are both friendly to the environment and hazardous free. The aim here is to assure adequate art studio and laboratory management, and provide students with hazard free health and environmentally safe concepts that can be incorporated in their professional lives.The school of Fine Arts at the University of Barcelona is part of a pilot program, where our experience in educational innovation and research is serving as a reference for the implantation of OSHAS 18001 norms.

Safety and sustainability research for university schools of fine arts

Designing new teaching programs for both undergraduate and graduate university studies involves integrating concepts and methodologies regarding quality, work safety and hazard prevention, and environmental protection. One of the challenges facing Spanish research within the realm of European Higher Education concerns health and safety issues in the Arts.In the case of Fine Arts, student exploration is one of the fundamental pillars of the study program; therefore it is imperative that art studios be optimized. This optimization affects both designated resources (infrastructures, materials, equipment, etc.) and organization of the teaching force.In this context, the aim of our research is to improve educational practices by designing quality measures that are both friendly to the environment and hazardous free. The aim here is to assure adequate art studio and laboratory management, and provide students with hazard free health and environmentally safe concepts that can be incorporated in their professional lives.The school of Fine Arts at the University of Barcelona is part of a pilot program, where our experience in educational innovation and research is serving as a reference for the implantation of OSHAS 18001 norms.

Safety and sustainability research for university schools of fine arts

Designing new teaching programs for both undergraduate and graduate university studies involves integrating concepts and methodologies regarding quality, work safety and hazard prevention, and environmental protection. One of the challenges facing Spanish research within the realm of European Higher Education concerns health and safety issues in the Arts.In the case of Fine Arts, student exploration is one of the fundamental pillars of the study program; therefore it is imperative that art studios be optimized. This optimization affects both designated resources (infrastructures, materials, equipment, etc.) and organization of the teaching force.In this context, the aim of our research is to improve educational practices by designing quality measures that are both friendly to the environment and hazardous free. The aim here is to assure adequate art studio and laboratory management, and provide students with hazard free health and environmentally safe concepts that can be incorporated in their professional lives.The school of Fine Arts at the University of Barcelona is part of a pilot program, where our experience in educational innovation and research is serving as a reference for the implantation of OSHAS 18001 norms.