Synthesis of Fe/Ti oxides from a single source alkoxide precursor under inert atmosphere

The heterometal alkoxide [FeCl{Ti2(OPr i)9}] (1) was employed as a single source precursor for the preparation of Fe/Ti oxides under inert atmosphere. Three different synthetic procedures were adopted in the processing of 1, either employing aqueous HNO3 or HCl solutions, or in the absence of mineral acids. Products were characterised by powder X-ray diffractometry, scanning electron microscopy combined with energy dispersive X-ray spectroscopy (SEM/EDS) and Raman, electron paramagnetic resonance (EPR) and Mössbauer spectroscopies. Oxide products contained titanium(IV) and either iron(III) or iron(II), depending on reaction conditions and thermal treatment temperatures. An interesting iron(III)→iron(II) reduction was observed at 1000 ºC in the HNO3-containing system, leading to the detection of ilmenite (FeTiO3). SEM/EDS studies revealed a highly heterogeneous metal distribution in all products, possibly related to the presence of a significant content of carbon and of structural defects (oxygen vacancies) in the solids.

Porcine skin as a source of biodegradable matrices: alkaline treatment and glutaraldehyde crosslinking

In this work, the modifications promoted by alkaline hydrolysis and glutaraldehyde (GA) crosslinking on type I collagen found in porcine skin have been studied. Collagen matrices were obtained from the alkaline hydrolysis of porcine skin, with subsequent GA crosslinking in different concentrations and reaction times. The elastin content determination showed that independent of the treatment, elastin was present in the matrices. Results obtained from in vitro trypsin degradation indicated that with the increase of GA concentration and reaction time, the degradation rate decreased. From thermogravimetry and differential scanning calorimetry analysis it can be observed that the collagen in the matrices becomes more resistant to thermal degradation as a consequence of the increasing crosslink degree. Scanning electron microscopy analysis indicated that after the GA crosslinking, collagen fibers become more organized and well-defined. Therefore, the preparations of porcine skin matrices with different degradation rates, which can be used in soft tissue reconstruction, are viable.

Photophysical properties and quantum chemical studies of poly(2,7-9,9'-dihexylfluorene-dyil)

This work reports the photophysical properties (excitation and fluorescence spectra, fluorescence quantum yield, fluorescence lifetimes) of the poly(2,7-9,9'-dihexylfluorene-dyil) in dilute solutions of four solvents (toluene, tetrahydrofuran, chloroform and ethyl acetate) as well as the properties in solid state. Photoluminescence showed spectra characteristic of disordered α-backbone chain conformation. Simulation of the electronic absorption spectra of oligomers containing 1 to 11 mers showed that the critical conjugation length is between 6 and 7 mers. We also estimated the theoretical dipole moments which indicated that a coil conformation is formed with 8 repeating units per turn. We also showed that some energy transfer process appears in solid state which decreases the emission lifetime. Furthermore, based on luminescent response of the systems herein studied and electroluminescent behavior reported on literature, both photo and electroluminescence emissions arise from the same emissive units.

Mechanical, thermal and morphological properties of glutaraldehyde crosslinked bovine pericardium followed by glutamic acid treatment

Major problems with valve bioprostheses are associated with progressive structural deterioration and calcification, directly associated with the use of glutaraldehyde (GA). This work describes the effects of GA processing and borate/glutamic acid buffer treatment on the mechanical, thermal and morphological properties of 0.5% GA crosslinked bovine pericardium (BP). The results showed that while the treatment of 0.5% GA crosslinked BP with borate/glutamic acid significantly improves the mechanical properties, it had no visible effect on surface morphology. Better surface preservation was only achieved for BP pre-treated with a lower GA concentration followed by the conventional treatment (0.5% GA). Improvements in mechanical properties probably arises from structural changes probably involving the depolymerization of polymeric GA crosslinks and an increase electrostatic interaction due to covalent binding of glutamic acid to free carbonyl groups (Schiff base).The results indicate that the treatment GA crosslinked BP with borate/glutamic acid buffer may be an attractive procedure for the manufacture of heart valve bioprostheses.

Photodynamic antimicrobial chemotherapy (PACT) for the treatment of malaria, leishmaniasis and trypanosomiasis

A photodynamic effect occurs when photosensitiser molecules absorb light and dissipate the absorbed energy by transferring it to biological acceptors (usually oxygen), generating an excess of reactive species that are able to force cells into death pathways. Several tropical diseases present physiopathological aspects that are accessible to the application of a photosensitiser and local illumination. In addition, disease may be transmitted through infected blood donations, and many of the aetiological agents associated with tropical diseases have been shown to be susceptible to the photodynamic approach. However, there has been no systematic investigation of the application of photoantimicrobial agents in the various presentations, whether to human disease or to the disinfection of blood products or even as photo-insecticides. We aim in this review to report the advances in the photoantimicrobial approach that are beneficial to the field of anti-parasite therapy and also have the potential to facilitate the development of low-cost/high-efficiency protocols for underserved populations.

Chemical constituents of the volatile oil from leaves of Annona coriacea and in vitro antiprotozoal activity

The essential oil of the leaves from Annona coriacea Mart., Annonaceae, was extracted by hydrodistillation in a Clevenger apparatus and analyzed by GC/MS and GC/FID. The oil yield was 0.05% m/m. Sixty compounds were identified, in a complex mixture of sesquiterpenes (76.7%), monoterpenes (20.0%) and other constituents (3.3%). Bicyclogermacrene was its major compound (39.8%) followed by other sesquiterpenes. Most of the monoterpenes were in low concentration (<1%). Only β-pinene and pseudolimonene presented the highest level of 1.6%. The volatile oil presented anti-leishmanial and trypanocidal activity against promastigotes of four species of Leishmania and trypomastigotes of Trypanosoma cruzi, showing to be more active against Leishmania (L.) chagasi (IC50 39.93 µ g/mL) (95% CI 28.00-56.95 µ g/mL).

Chemical composition and acetylcholinesterase inhibitory activity of essential oils of Myrceugenia myrcioides(Cambess.) O. Berg and Eugenia riedelianaO. Berg, Myrtaceae

The chemical composition of volatile oils from two Myrtaceae species, Myrceugenia myrcioidesand Eugenia riedeliana, both native from the Brazilian Atlantic Rain Forest, was analyzed by GC-MS. Acetylcholinesterase inhibitory activity was colorimetrically evaluated for these oils. For M. myrcioides, monoterpene hydrocarbons represented the major class in the volatile oil, with α-pinene as the most abundant component and a weak inhibitory activity was observed, whilst for E. riedeliana sesquiterpenes were found in higher amounts, being valerianol the major compound, and this oil presented a strong acetylcholinesterase inhibition.

I2: uma molécula didática

Iodine vapor is a very suitable substance to learn about molecular energy levels and transitions, and to introduce spectroscopic techniques. As a diatomic molecule its spectra are relatively simple and allow straightforward treatment of the data leading to the potential energy curves and to quantum mechanics concepts. The overtone bands, in the resonance Raman scattering, and the band progressions, in the electronic spectra, play an important role in the calculation of the Morse potential curves for the fundamental and excited electronic state. A weaker chemical bond in the electronic excited state, compared to the fundamental state, is evidenced by the increase in the equilibrium interatomic distance. The resonance Raman scattering of I2 is highlighted due to its importance for obtaining the anharmonicity constant in the fundamental electronic state.

Effect of experimental heat treatment on mechanical properties of resin composites

The aim of this study was to verify the influence of an experimental heat treatment (170ºC/10 min) using a casting furnace on the mechanical properties (hardness and flexural strength) of 2 commercial direct resin composites (TPH Spectrum and Filtek P60) compared to a commercial indirect resin system (BelleGlass). Heat treatment temperature was determined after thermal characterization by thermogravimetry (TG) and differential scanning calorimetry (DSC). Data was analyzed by ANOVA and Tukey's test at 5% significance level. There was statistical significance for the main factor heat treatment (p=0.03) and composite (p=0.02), for flexural strength. For Knoop hardness, only the main factor composite was statistically significant (p=0.00). P60 presented higher hardness than TPH. No statistically significant correlation between mechanical properties tested was detected. Based on these results, it was possible to conclude that heat treatment influenced flexural strength of direct composites, while it was not observed for hardness. The association of direct composites with a simple post-cure heat treatment may be an alternative for current indirect composite systems, although more studies are needed to verify other properties of the composites for this application.

Nutritional aspects of the prevention and treatment of osteoporosis

Osteoporosis is a global health problem characterized by low bone mass and microarchitectural deterioration of bone tissue with a consequent increase in bone fragility and susceptibility to fracture. Nutrition plays a critical role in reducing the risk of osteoporosis through its effect on all of these fragility factors, especially on the development and maintenance of bone mass. An adequate calcium, vitamin D and protein intake resulted in reduced bone remodeling, better calcium retention, reduced age-related bone loss, and reduced fracture risk. Recent evidence indicates that a healthy dietary pattern including dairy products (mainly fat free), fruit and vegetables and adequate amounts of meat, fish and poultry is positively related to bone health. Furthermore, mineral and vitamin supplementation should be closely monitored by health professionals since it could have adverse effects and be insufficient to ensure optimal protection of bone health.

Energy and amino acid content in phase 1 nursery diet: piglet performance and body chemical composition

It was evaluated the effects of metabolizable energy (ME) and digestible lysine (dLYS) densities on performance and body composition of weaned piglets. The study used 114 piglets weaned at 7.4 ± 0.80 kg, out of which 108 were allotted in the nursery and 6 were slaughtered on the weaning day to determine comparative data of body chemical composition. Six nutrients densities were stipulated from a previous study based on the highest nitrogen retention, maintaining the following ME:LYS relationship in the experimental diets: 3,390:1.291; 3,450:1.409; 3,650:1.411; 3,780:1.461; 3,940:1.507; and 4,109 kcal/kg ME:1.564% dLYS. The experimental diets were offered for 13 days when the piglets reached 12.986 ± 1.449 kg of body weight. The probable residual effects of nutritional density on the subsequent performance of the piglets were evaluated. At the end of initial phase 1, six piglets from each density were slaughtered to determine their chemical composition in body fractions and empty body. There was no significant influence of nutritional levels on the performance of the piglets at the end of the evaluation. The results of food conversion and body composition confirm the level indicated in the previous study, 4 g dLYS/Mcal of ME. The increase of energy and lysine densities confirms the need for a correct relationship among both of them to assure better performance of the piglets at the beginning of the growing phase.

Efeitos do teor de carboidratos solúveis sobre as características da silagem de cana-de-açúcar

Objetivou-se quantificar na cana-de-açúcar o teor de carboidratos solúveis (CHOs) que anula a produção de etanol e avaliar os efeitos desses carboidratos sobre o valor nutritivo e outras características fermentativas da silagem de cana-de-açúcar. Utilizou-se o delineamento inteiramente casualizado com três tratamentos, cada um com quatro repetições. Os tratamentos consistiram da retirada total do caldo da cana-de-açúcar, por meio de prensagem, e de sua reconstituição (0, 50 ou 100%) à cana. No nível de 50% de reconstituição, o caldo foi adicionado à cana juntamente com 50% de água e, no nível 0%, adicionou-se 100% de água à cana. A restituição resultou em concentrações de 41,6; 34,0 e 23,0% de carboidratos solúveis na matéria seca (MS). O material foi ensilado em 12 silos experimentais confeccionados a partir de baldes plásticos. A abertura dos silos foi realizada 85 dias após a ensilagem, quando foram determinados os teores dos ácidos orgânicos e a composição química das silagens. A retirada de carboidratos solúveis da cana-de-açúcar teve efeito linear decrescente sobre os teores de matéria seca, o teor de carboidratos solúveis e a digestibilidade in vitro da matéria seca (DIVMS) das silagens, no entanto, ocasionou aumento dos teores de fibra detergente ácido (FDA), fibra detergente neutro (FDN) e lignina. Observou-se efeito linear decrescente da retirada dos carboidratos solúveis sobre os teores de etanol e ácidos lático e butírico e as perdas de matéria seca das silagens. Não se observaram efeitos de tratamentos sobre os dados de estabilidade aeróbia. A produção de etanol seria nula se a cana-de-açúcar contivesse apenas 12,4% de CHOs com base na matéria seca (MS).

Effect of fructans-based fat replacer on chemical composition, starch digestibility and sensory acceptability of corn snacks

To develop a convenience healthy food snack the partially hydrogenated vegetable fat, used as the flavour fixative agent, was replaced by a non-fat-flavouring solution enriched with inulin and oligofructose. The effects of this replacement on chemical composition, in vitro rate of starch digestion and sensory acceptability were assessed. The new snack presented low-fat levels (0.1 per cent) and around a sevenfold increase in dietary fibre (15.3 per cent of dietary fibre, being 13.3 per cent of fructans) when compared with the traditional ones. The enrichment with fructans reduced the predicted Glycaemic Index by 25 per cent, thus indicating that this dietary fibre contributes effectively towards delaying the in vitro glycaemic response. Fructans-enriched snack presented overall acceptability score (6.6 ± 1.7) similar to the traditional one, flavoured with fatty fixative agent (7.4 ± 1.4). The healthy low-fat fibre-enriched snack produced presented the high sensory acceptability typical for this food product type

Nutrional aspects of the prevention and treatment of osteoporosis

A osteoporose é um problema de saúde global, caracterizada por baixa massa óssea e deterioração da microarquitetura do tecido ósseo, com consequente aumento da fragilidade óssea e suscetibilidade a fraturas. A nutrição desempenha um papel fundamental na redução do risco de osteoporose por seu efeito sobre todos os fatores relacionados à fragilidade óssea, principalmente no desenvolvimento e na manutenção da massa óssea. Uma adequada ingestão de cálcio, vitamina D e proteína leva à redução da remodelação óssea, à maior retenção de cálcio, à redução da perda óssea relacionada à idade e à redução do risco de fraturas. Evidências recentes indicam que uma alimentação saudável, incluindo a ingestão de produtos lácteos (principalmente os desnatados), frutas e verduras, e uma quantidade adequada de carnes, peixes e aves, está relacionada positivamente com a saúde óssea. Além disso, a suplementação de vitaminas e minerais deve ser monitorada de perto, por profissionais de saúde, uma vez que pode ter efeitos adversos e ser insuficiente para assegurar uma eficaz proteção à saúde óssea

Disponibilidade de metais pesados em Latossolo com aplicação superficial de escória, lama cal, lodos de esgoto e calcário

O objetivo deste trabalho foi avaliar alguns atributos químicos do solo e a disponibilidade de cádmio (Cd), cromo (Cr), níquel (Ni), mercúrio (Hg), chumbo (Pb) e arsênio (As), por meio da extração pelo DTPA,em conseqüência da aplicação superficial de escória de aciaria, lama cal e lodos de esgoto centrifugados e de biodigestores, nas doses 0 (testemunha), 2, 4 e 8 Mg ha-1 e um tratamento adicional composto pela calagem superficial na dose 2 Mg ha-1. O experimento foi conduzido em delineamento de blocos ao acaso, em condições de campo, em área sob sistema plantio direto, durante 2003 e 2004. A aplicação superficial de escória de aciaria,lama cal, lodo de esgoto centrifugado e de biodigestor, até a dose 8 Mg ha-1, assim como o calcário na dose 2 Mg ha-1, não trazem problemas de disponibilidade ao ambiente, com relação aos metais pesados Cd, Cr, Hg, Pb, Ni e As, quando aplicados sobre a superfície em Latossolo Vermelho distrófico, no sistema plantio direto. A fitodisponibilidade de metais pesados às culturas da soja e aveia-preta foi nula, quando foram aplicadas doses de até 8 Mg ha-1 de lodo de esgoto, escória e lama cal sobre a superfície do solo, no sistema plantio direto