High-Pressure Methane Storage in Porous Materials: Are Carbon Materials in the Pole Position?

Natural gas storage on porous materials (ANG) is a promising alternative to conventional on-board compressed (CNG) or liquefied natural gas (LNG). To date, Metal–organic framework (MOF) materials have apparently been the only system published in the literature that is able to reach the new Department of Energy (DOE) value of 263 cm3 (STP: 273.15 K, 1 atm)/cm3; however, this value was obtained by using the ideal single-crystal density to calculate the volumetric capacity. Here, we prove experimentally, and for the first time, that properly designed activated carbon materials can really achieve the new DOE value while avoiding the additional drawback usually associated with MOF materials (i.e., the low mechanical stability under pressure (conforming), which is required for any practical application).

Micro/Mesoporous Activated Carbons Derived from Polyaniline: Promising Candidates for CO2 Adsorption

A series of activated carbons were prepared by carbonization of polyaniline at different temperatures, using KOH or K2CO3 as activating agent. Pure microporous or micro/mesoporous activated carbons were obtained depending on the preparation conditions. Carbonization temperature has been proven to be a key parameter to define the textural properties of the carbon when using KOH. Low carbonization temperatures (400–650 °C) yield materials with a highly developed micro- and mesoporous structure, whereas high temperatures (800 °C) yield microporous carbons. Some of the materials prepared using KOH exhibit a BET surface area superior to 4000 m2/g, with total pore volume exceeding 2.5 cm3/g, which are among the largest found for activated carbons. On the other hand, microporous materials are obtained when using K2CO3, independently of carbonization temperature. Some of the materials were tested for CO2 capture due to their high microporosity and N content. The adsorption capacity for CO2 at atmospheric pressure and 0 °C achieves a value of ∼7.6 mmol CO2/g, which is among the largest reported in the literature. This study provides guidelines for the design of activated carbons with a proper N/C ratio for CO2 capture at atmospheric pressure.

Structural Characterization of Micro- and Mesoporous Carbon Materials Using In Situ High Pressure 129Xe NMR Spectroscopy

In situ high pressure 129Xe NMR spectroscopy in combination with volumetric adsorption measurements were used for the textural characterization of different carbon materials with well-defined porosity including microporous carbide-derived carbons, ordered mesoporous carbide-derived carbon, and ordered mesoporous CMK-3. Adsorption/desorption isotherms were measured also by NMR up to relative pressures close to p/p0 = 1 at 237 K. The 129Xe NMR chemical shift of xenon adsorbed in porous carbons is found to be correlated with the pore size in analogy to other materials such as zeolites. In addition, these measurements were performed loading the samples with n-nonane. Nonane molecules preferentially block the micropores. However, 129Xe NMR spectroscopy proves that the nonane also influences the mesopores, thus providing information about the pore system in hierarchically structured materials.

Use of Eutectic Mixtures for Preparation of Monolithic Carbons with CO2-Adsorption and Gas-Separation Capabilities

With global warming becoming one of the main problems our society is facing nowadays, there is an urgent demand to develop materials suitable for CO2 storage as well as for gas separation. Within this context, hierarchical porous structures are of great interest for in-flow applications because of the desirable combination of an extensive internal reactive surface along narrow nanopores with facile molecular transport through broad “highways” leading to and from these pores. Deep eutectic solvents (DESs) have been recently used in the synthesis of carbon monoliths exhibiting a bicontinuous porous structure composed of continuous macroporous channels and a continuous carbon network that contains a certain microporosity and provides considerable surface area. In this work, we have prepared two DESs for the preparation of two hierarchical carbon monoliths with different compositions (e.g., either nitrogen-doped or not) and structure. It is worth noting that DESs played a capital role in the synthesis of hierarchical carbon monoliths not only promoting the spinodal decomposition that governs the formation of the bicontinuous porous structure but also providing the precursors required to tailor the composition and the molecular sieve structure of the resulting carbons. We have studied the performance of these two carbons for CO2, N2, and CH4 adsorption in both monolithic and powdered form. We have also studied the selective adsorption of CO2 versus CH4 in equilibrium and dynamic conditions. We found that these materials combined a high CO2-sorption capacity besides an excellent CO2/N2 and CO2/CH4 selectivity and, interestingly, this performance was preserved when processed in both monolithic and powdered form.

Retos actuales para la captura y almacenamiento de CO2

Las grandes emisiones de CO2 procedentes de la combustión de combustibles fósiles están provocando un calentamiento global en nuestro planeta. Estos problemas medioambientales están obligando a los diferentes gobiernos a buscar soluciones que permitan reducir esas emisiones y mitigar sus efectos adversos. Una de las soluciones más prometedoras consiste en la captura selectiva de CO2 en efluentes industriales mediante el uso de materiales adsorbentes porosos (zeolitas, carbón activado y materiales híbridos MOFs) que combinen una elevada capacidad de adsorción y una adecuada selectividad a CO2 frente al resto de gases del proceso industrial, además de una adecuada regeneración.

Superior performance of gold supported on doped CeO2 catalysts for the preferential CO oxidation (PROX)

Herein, the preferential oxidation of CO in excess hydrogen (PROX reaction) was studied over Au catalysts supported on ceria and Y or Nb doped ceria. Both supports and catalysts have been extensively characterized by a number of advanced techniques; XRD, N2-adsortion, Raman spectroscopy, XPS, and H2-TPR. The catalytic results showed that when an ideal mixture of H2 and CO is used for the PROX reaction the gold supported on pure ceria behaves better than the others samples. However, when a typical reformate gas composition containing CO2 and H2O is used, the gold supported on Nb doped sample behaves better than gold supported in pure ceria. It is suggested that niobium hampers the strong adsorption of CO2 and H2O in the active sites, thus improving the catalytic performance in real reformate gas.

Activated Carbons Impregnated with Na2S and H2SO4: Texture, Surface Chemistry and Application to Mercury Removal from Aqueous Solutions

The effects of treatment of an activated carbon with Sulphur precursors on its textural properties and on the ability of the complex synthesized for mercury removal in aqueous solutions are studied. To this end, a commercial activated carbon has been modified by treatments with aqueous solutions of Na2S and H2SO4 at two temperatures (25 and 140 °C) to introduce sulphur species on its surface. The prepared adsorbents have been characterized by N2 (-196 °C) and CO2 (0 °C) adsorption, thermogravimetric analysis, temperature-programmed decomposition and X-ray photoelectron spectroscopy, and their adsorption capacities to remove Hg(II) ions in aqueous solutions have been determined. It has been shown that the impregnation treatments slightly modified the textural properties of the samples, with a small increase in the textural parameters (BET surface area and mesopore volumes). By contrast, surface oxygen content was increased when impregnation was carried out with Na2S, but it decreased when H2SO4 was used. However, the main effect of the impregnation treatments was the formation of surface sulphur complexes of thiol type, which was only achieved when the impregnation treatments were carried out at low temperature (25 °C). The presence of surface sulphur enhances the adsorption behaviour of these samples in the removal of Hg(II) cations in aqueous solutions at pH 2. In fact, complete Hg(II) removal is only obtained with the sulphur-containing activated carbons.

Very high methane uptake on activated carbons prepared from mesophase pitch: A compromise between microporosity and bulk density

Two petroleum residues were pyrolyzed under two different conditions to obtain pitches with low or high mesophase content. The effect of the KOH: precursor ratio and the activation temperature on the packing density and porous texture of the carbons have been studied and optimized. Activated carbons combining high micropore volume (>1 cm3/g) and high packing density (0.7 g/cm3) have been successfully prepared. Regarding excess methane adsorption capacities, the best results (160 cm3 (STP)/cm3 at 25 °C and 3.5 MPa) were obtained using the pitch with the higher content of the more organized mesophase, activated at relatively low temperature (700 °C), with a medium KOH: precursor ratio (3:1). Some of the activated carbons exhibit enhanced adsorption capacity at high pressure, giving values as high as 175 cm3 (STP)/cm3 at 25 °C and 5 MPa and 200 cm3 (STP)/cm3 at 25 °C and 10 MPa (the same amount as in an empty cylinder but at half of the pressure), indicating a contribution of large micropores and narrow mesopores to adsorption at high pressure. The density of methane in pores between 1 and 2.5 nm at pressure up to 10 MPa was estimated to understand their contribution to the total adsorption capacity.

Spectroscopic, calorimetric, and catalytic evidences of hydrophobicity on Ti-MCM-41 silylated materials for olefin epoxidations

Hydrophobic Ti-MCM-41 samples prepared by post-synthesis silylation treatment demonstrate to be highly active and selective catalysts in olefins epoxidation by using organic hydroperoxides as oxidizing agents in liquid phase reaction systems. Epoxide yields show important enhancements with increased silylation degrees of the Ti-mesoporous samples. Catalytic studies are combined and correlated with spectroscopic techniques (e.g. XRD, XANES, UV-Visible, 29Si MAS-NMR) and calorimetric measurements to better understand the changes in the surface chemistry of Ti-MCM-41 samples due to the post-synthesis silylation treatment and to ascertain the role of these trimethylsilyl groups incorporated in olefin epoxidation. In such manner, the effect of the organic moieties on solids, and both water and glycol molecules contents on the catalytic activity and selectivity are analyzed in detail. Results show that the hydrophobicity level of the samples is responsible for the decrease in water adsorption and, consequently, the negligible formation of the non-desired glycol during the catalytic process. Thus, catalyst deactivation by glycol poisoning of Ti active sites is greatly diminished, this increasing catalyst stability and leading to practically quantitative production of the corresponding epoxide. The extended use of these hydrophobic Ti-MCM-41 catalysts together with organic hydroperoxides for the highly efficient and selective epoxidation of natural terpenes is also exemplified.

Paving the way for methane hydrate formation on metal–organic frameworks (MOFs)

The presence of a highly tunable porous structure and surface chemistry makes metal–organic framework (MOF) materials excellent candidates for artificial methane hydrate formation under mild temperature and pressure conditions (2 °C and 3–5 MPa). Experimental results using MOFs with a different pore structure and chemical nature (MIL-100 (Fe) and ZIF-8) clearly show that the water–framework interactions play a crucial role in defining the extent and nature of the gas hydrates formed. Whereas the hydrophobic MOF promotes methane hydrate formation with a high yield, the hydrophilic one does not. The formation of these methane hydrates on MOFs has been identified for the first time using inelastic neutron scattering (INS) and synchrotron X-ray powder diffraction (SXRPD). The results described in this work pave the way towards the design of new MOF structures able to promote artificial methane hydrate formation upon request (confined or non-confined) and under milder conditions than in nature.

Adecuación del perímetro del edificio escolar del Viaducto y mejora de accesos para PMR

Tras observar detenidamente el viario y accesos de uno de los edificios más emblemáticos de la ciudad como puede ser el edificio escolar del Viaducto, se prevé actuar tanto en él como en su perímetro con el fin de mejorar la accesibilidad y movilidad tanto de los peatones que circulan por el barrio como a los estudiantes que acceden al edificio a diario. Se trata de un edificio del siglo XIX bautizado como la Escuela Industrial de Ingenieros por la Universidad Politécnica de Valencia; actualmente sigue perteneciendo a la Universidad y tras la nueva construcción del campus en Alcoy, se siguen impartiendo numerosos cursos por parte del Ayuntamiento y de la misma Universidad. La zona del Viaducto actualmente se encuentra en mal estado, complicando la accesibilidad para el peatón y restringiendo el paso a las personas con movilidad reducida por su complicada orografía y diseño urbano. Es por ello, que existe una necesidad de mejorar la zona y conseguir una accesibilidad para toda la población fomentando el predominio del peatón y las mejoras que esto conlleva. El proyecto, para justificar estas necesidades, elabora en su extensión un análisis previo de la situación actual y su problemática. Una vez recogidos todos los datos necesarios, mediante un estudio de soluciones, se adopta la solución adecuada para la problemática descrita y se materializa a lo largo del proyecto.

Synthesis of denim waste-based adsorbents and their application in water defluoridation

This study evaluates the application of denim fiber scraps as a precursor for the synthesis of adsorbents for water treatment via pyrolysis and their application in water defluoridation. The best pyrolysis conditions for the synthesis of this novel adsorbent have been identified and a metal doping route with different salts of Al3 +, La3 + and Fe3 + was proposed to improve its fluoride adsorption behavior. Different spectroscopic and microscopic techniques (i.e., FTIR, XPS, XRF, SEM) were used to characterize the precursor and adsorbents, and to analyze the surface interactions involved in the fluoride removal mechanism. Experimental results showed that these adsorbents were effective for fluoride adsorption showing uptakes up to 4.25 mg/g. The Si-O–metal–F interactions appear to be highly relevant for the fluoride removal. This study highlights the potential of denim textile waste as a raw material for the production of added-value products, thus minimizing their associated disposal cost. It also shows the performance of denim textile waste as a precursor of adsorbents for addressing relevant environmental concerns such as fluoride pollution.

Ecoepidemiología de Chlamydophila psittaci, pecorum, pneumoniae, abortus en Córdoba

Las Clamidias son bacterias patógenas de los animales de producción, de vida silvestre y de compañía. Además de las pérdidas económicas que producen las infecciones en los planteles de producción bovina, ovina, caprina, porcina y aves de corral, la mayoría de las especies tienen importancia zoonótica, pudiendo dar origen a infecciones graves, potencialmente letales en el ser humano. El orden Chlamydiales está integrado por bacterias que actúan como parásitos intracelulares obligados que desarrollan su ciclo de vida únicamente dentro de inclusiones citoplasmáticas. En este orden se encuentra la familia Chlamydiaceae que comprende dos géneros, Chlamydia y Chlamydophila; y las especies, Chlamydia trachomatis, C. suis, C. muridarum, Chlamydophila psittaci, C. abortus, C. felis, C. caviae, C. pecorum, y C. pneumoniae. C. psittaci causa psitacosis o clamidiosis aviar. En Argentina, los primeros casos clínicos de psitacosis fueron reportados en 1929. Los criadores de aves y quienes las poseen como mascotas, representan el grupo de mayor riesgo; pero también las personas que trabajan en pajarerías y aquellas que por su empleo se ven expuestas a contraer la enfermedad (empleados en peladeros donde se carnean y procesan pollos y otras aves para consumo, veterinarios, empleados de zoológicos, etc.). La infección en humanos se presenta como una neumonía severa; con fiebre alta, escalofríos, dolor de cabeza, mialgia y dificultad respiratoria. Ocasionalmente puede presentarse vómitos, dolor abdominal, diarrea y complicaciones como miocarditis, endocarditis, encefalitis, ictericia y fallas multiorgánicas, que pueden ser fatales sino se le administra el tratamiento adecuado. La infección en las mujeres embarazadas puede producir neumonía, hepatitis, insuficiencia renal, sepsis, parto prematuro y muerte fetal. Existen más de 465 especies de aves en las que se registró C. psittaci, incluyendo ornamentales, de corral, silvestres, acuáticas y palomas. Las patologías que pueden producir en estos animales son neumonitis, conjuntivitis, encefalomielitis, placentopatías, fetopatías, anorexia, diarrea e infecciones persistentes asintomáticas u oligosintomáticas. En bovinos, C. pecorum, C. abortus y C. psittaci producen infecciones respiratorias y genitales; que se presentan como cuadros de enteritis, artritis, encefalomielitis, endometritis e hipofertilidad. En Argentina, la infección clamidial en el ganado caprino fue asociada a daños en el tejido uterino, abortos, partos prematuros y crías débiles. En equinos, C. psittaci y C. pneumoniae producen abortos y desórdenes respiratorios, con un gran impacto en ganadería que redunda en pérdidas económicas. Considerando que existen escasos estudios eco-epidemiológicos y clínicos que reporten el estado de situación de estas infecciones en nuestro medio, es que el presente trabajo propone actualizar y profundizar el conocimiento de las especies de Clamidias de importancia médico-veterinaria presentes en la provincia de Córdoba, Argentina. El desarrollo de este proyecto aportará la implementación de técnicas que mejorarán el diagnóstico microbiológico, confirmarán los cuadros clínicos; y por lo tanto contribuirá al conocimiento de estos agentes infecciosos en nuestra región. Esta información es indispensable para los organismos responsables de la Salud Pública (Ministerios de Salud y Educación, Municipios, etc.) para que puedan obrar en consecuencia y generar sistemas de alerta temprana, tomar medidas de prevención y medidas de control frente a la presencia de un brote epidémico por alguna cepa clamidial.

Dermatomiosite, neoplasia da mama e Orlistat : que associação?

Trabalho Final do Curso de Mestrado Integrado em Medicina, Faculdade de Medicina, Universidade de Lisboa, 2014

A Importância da participação dos pais na creche e no jardim de infância : quais os obstáculos à participação dos pais

Relatório apresentado para a obtenção do grau de mestre em Educação pré-escolar