(Table 2) Bottom-hole temperature measurements at DSDP Sites 68-501, 69-504, and 69-505

Drilling durin Deep Sea Drilling Project Legs 68, 69, and 70 on the southern limb of the Costa Rica Rift was used to study geothermal processes in the ocean crust. Two areas were drilled. One was a geothermally hot site on 6.2-m.y.-old crust, where topography is smooth, heat flow is close to that predicted by conductive cooling of the lithosphere (200 mWm**-2), and hydrothermal circulation may be sealed within the crust. The other was on 3.9-m.y.-old crust, where rough topography is associated with low heat flow (15 to 50 mWm**-2) and possible open convection of sea water. At both sites, about 250 m of siliceous-calcareous sediments overlies igneous basement. In the hot area, it blankets the topography, whereas in the cold area, basement outcrops still occur. Operations included numerous down-hole experiments in both areas and hydraulic piston coring of a 230-m sediment section in the hot area. Diagenesis of the sediments appears closely related to temperature. At the hot site, chert was found near basement, and the chemistry of pore fluids, sampled from both sediments and basement, is strongly influenced by reactions within the basement. Strong lateral gradients in the composition of pore fluids occur in the sediments. At the cold site, no chert was found, and bacterial processes within the sediment dominated the chemistry of the pore fluids. Basaltic basement in both areas consists mainly of pillow lavas and thin flows, with occasional more massive units. The basalt is relatively magnesian. The degree of alteration is very small in the cold area, but much more extensive in the hot area. Ease of drilling also shows a strong contrast. Basement penetration reached 562 m in the hot area and was halted because of lack of time; at the cold site, 43 m of basement was cored only with difficulty. The most intensive in-hole experiments were conducted in the hot area. Successful runs with the borehole televiewer allowed basement lithology to be determined and showed the presence of more and less fractured zones. Pulse tests using a single borehole packer gave values of basement permeability of about 2 to 40 millidarcies. Numerous temperature logs established a broadly conductive in situ temperature gradient, with temperatures reaching 120°C at 562 m into the basement. However, anomalously low temperatures in the upper part of the hole, which persisted after drilling disturbance had decayed away, showed that cold ocean water was flowing down the hole and into the basement at about 90 m below the base of the sediments, at rates of about 80 to 100 m/hr. The packer records indicate a pressure at this depth of 10 bars below hydrostatic.

Sensitive Questions in Online Surveys: Experimental Results for the Randomized Response Technique (RRT) and the Unmatched Count Technique (UCT)

Gaining valid answers to so-called sensitive questions is an age-old problem in survey research. Various techniques have been developed to guarantee anonymity and minimize the respondent's feelings of jeopardy. Two such techniques are the randomized response technique (RRT) and the unmatched count technique (UCT). In this study we evaluate the effectiveness of different implementations of the RRT (using a forced-response design) in a computer-assisted setting and also compare the use of the RRT to that of the UCT. The techniques are evaluated according to various quality criteria, such as the prevalence estimates they provide, the ease of their use, and respondent trust in the techniques. Our results indicate that the RRTs are problematic with respect to several domains, such as the limited trust they inspire and non-response, and that the RRT estimates are unreliable due to a strong false "no" bias, especially for the more sensitive questions. The UCT, however, performed well compared to the RRTs on all the evaluated measures. The UCT estimates also had more face validity than the RRT estimates. We conclude that the UCT is a promising alternative to RRT in self-administered surveys and that future research should be directed towards evaluating and improving the technique.

Electromagnetic Instability Studies in Fusion Plasmas Edge

Este trabajo esta dedicado al estudio de las estructuras macroscópicas conocidas en la literatura como filamentos o blobs que han sido observadas de manera universal en el borde de todo tipo de dispositivos de fusión por confinamiento magnético. Estos filamentos, celdas convectivas elongadas a lo largo de las líneas de campo que surgen en el plasma fuertemente turbulento que existe en este tipo de dispositivos, parecen dominar el transporte radial de partículas y energía en la región conocida como Scrape-off Layer, en la que las líneas de campo dejan de estar cerradas y el plasma es dirigido hacia la pared sólida que forma la cámara de vacío. Aunque el comportamiento y las leyes de escala de estas estructuras son relativamente bien conocidos, no existe aún una teoría generalmente aceptada acerca del mecanismo físico responsable de su formación, que constituye una de las principales incógnitas de la teoría de transporte del borde en plasmas de fusión y una cuestión de gran importancia práctica en el desarrollo de la siguiente generación de reactores de fusión (incluyendo dispositivos como ITER y DEMO), puesto que la eficiencia del confinamiento y la cantidad de energía depositadas en la pared dependen directamente de las características del transporte en el borde. El trabajo ha sido realizado desde una perspectiva eminentemente experimental, incluyendo la observación y el análisis de este tipo de estructuras en el stellarator tipo heliotrón LHD (un dispositivo de gran tamaño, capaz de generar plasmas de características cercanas a las necesarias en un reactor de fusión) y en el stellarator tipo heliac TJ-II (un dispositivo de medio tamaño, capaz de generar plasmas relativamente más fríos pero con una accesibilidad y disponibilidad de diagnósticos mayor). En particular, en LHD se observó la generación de filamentos durante las descargas realizadas en configuración de alta _ (alta presión cinética frente a magnética) mediante una cámara visible ultrarrápida, se caracterizó su comportamiento y se investigó, mediante el análisis estadístico y la comparación con modelos teóricos, el posible papel de la Criticalidad Autoorganizada en la formación de este tipo de estructuras. En TJ-II se diseñó y construyó una cabeza de sonda capaz de medir simultáneamente las fluctuaciones electrostáticas y electromagnéticas del plasma. Gracias a este nuevo diagnóstico se pudieron realizar experimentos con el fin de determinar la presencia de corriente paralela a través de los filamentos (un parámetro de gran importancia en su modelización) y relacionar los dos tipos de fluctuaciones por primera vez en un stellarator. Así mismo, también por primera vez en este tipo de dispositivo, fue posible realizar mediciones simultáneas de los tensores viscoso y magnético (Reynolds y Maxwell) de transporte de cantidad de movimiento. ABSTRACT This work has been devoted to the study of the macroscopic structures known in the literature as filaments or blobs, which have been observed universally in the edge of all kind of magnetic confinement fusion devices. These filaments, convective cells stretching along the magnetic field lines, arise from the highly turbulent plasma present in this kind of machines and seem to dominate radial transport of particles and energy in the region known as Scrapeoff Layer, in which field lines become open and plasma is directed towards the solid wall of the vacuum vessel. Although the behavior and scale laws of these structures are relatively well known, there is no generally accepted theory about the physical mechanism involved in their formation yet, which remains one of the main unsolved questions in the fusion plasmas edge transport theory and a matter of great practical importance for the development of the next generation of fusion reactors (including ITER and DEMO), since efficiency of confinement and the energy deposition levels on the wall are directly dependent of the characteristics of edge transport. This work has been realized mainly from an experimental perspective, including the observation and analysis of this kind of structures in the heliotron stellarator LHD (a large device capable of generating reactor-relevant plasma conditions) and in the heliac stellarator TJ-II (a medium-sized device, capable of relatively colder plasmas, but with greater ease of access and diagnostics availability). In particular, in LHD, the generation of filaments during high _ discharges (with high kinetic to magnetic pressure ratio) was observed by means of an ultrafast visible camera, and the behavior of this structures was characterized. Finally, the potential role of Self-Organized Criticality in the generation of filaments was investigated. In TJ-II, a probe head capable of measuring simultaneously electrostatic and electromagnetic fluctuations in the plasma was designed and built. Thanks to this new diagnostic, experiments were carried out in order to determine the presence of parallel current through filaments (one of the most important parameters in their modelization) and to related electromagnetic (EM) and electrostatic (ES) fluctuations for the first time in an stellarator. As well, also for the first time in this kind of device, measurements of the viscous and magnetic momentum transfer tensors (Reynolds and Maxwell) were performed.

Estudio de la tecnología IMS y diseño de una solución de telefonía multimedia

El objetivo fundamental del Proyecto Fin de Carrera es ofrecer una visión global de la arquitectura de red IMS (“IP Multimedia Subsystem”) conociendo el comportamiento de los nodos que la forman y las funcionalidades que cada uno de ellos implementa. Durante la realización del proyecto se ha tenido en cuenta que las redes IMS han transformando el sector de las telecomunicaciones debido a la gran convergencia de los servicios que ofrece. Esta tecnología presenta un amplio abanico a las aplicaciones multimedia, tanto en el entorno empresarial como residencial. Como desarrollo práctico se expone un diseño de alto nivel que consiste en la ampliación de la capacidad existente de uno de los nodos de la red IMS para un operador nacional ofreciendo el servicio ‘Business Trunking’ para grandes clientes. El objetivo destinado alcanzar con este caso práctico es el análisis del impacto que supone la inclusión de este nuevo elemento en el resto de nodos que forman la red. Consiguiendo demostrar la facilidad para el operador, a la hora de ampliar la capacidad de su red, sin olvidarnos que esto conlleva numerosos beneficios tanto a nivel de proveedor como de usuario final. The principal objective in this Final Degree Project is to provide an overview of the architect of the IMS Network, considering the behavior of nodes that integrate this network and the main functionalities that each of them implements. During the study of this Project has taken into account that IMS network has turned Telecommunications world, due to the strong convergence of the services offered. This technology shows a wide range of multimedia applications, in enterprise as much as residential environment. As a practical development a high-level design is presented. It involves the expansion of existing capacity for one of IMS network nodes for a national operator offering ‘Business Trunking’ service for enterprises. The goal to achieve in this case is to analyze the impact caused by the inclusion of this new element in the rest of the nodes within the IMS network. To manage to prove the ease of the operator, in expanding the capacity of its network, and considering IMS technology allows to obtain several benefits for both supplier and end user.

Analyzing logic programs with dynamic scheduling

Traditional logic programming languages, such as Prolog, use a fixed left-to-right atom scheduling rule. Recent logic programming languages, however, usually provide more flexible scheduling in which computation generally proceeds leftto- right but in which some calis are dynamically "delayed" until their arguments are sufRciently instantiated to allow the cali to run efficiently. Such dynamic scheduling has a significant cost. We give a framework for the global analysis of logic programming languages with dynamic scheduling and show that program analysis based on this framework supports optimizations which remove much of the overhead of dynamic scheduling.

Tools for constraint visualization: The VIFID/TRIFID tool

Visualization of program executions has been used in applications which include education and debugging. However, traditional visualization techniques often fall short of expectations or are altogether inadequate for new programming paradigms, such as Constraint Logic Programming (CLP), whose declarative and operational semantics differ in some crucial ways from those of other paradigms. In particular, traditional ideas regarding the behavior of data often cannot be lifted in a straightforward way to (C)LP from other families of programming languages. In this chapter we discuss techniques for visualizing data evolution in CLP. We briefly review some previously proposed visualization paradigms, and also propose a number of (to our knowledge) novel ones. The graphical representations have been chosen based on the perceived needs of a programmer trying to analyze the behavior and characteristics of an execution. In particular, we concéntrate on the representation of the run-time valúes of the variables, and the constraints among them. Given our interest in visualizing large executions, we also pay attention to abstraction techniques, i.e., techniques which are intended to help in reducing the complexity of the visual information.

The ciao module system: A new module system for prolog

Ciao Prolog incorporates a module system which allows sepárate compilation and sensible creation of standalone executables. We describe some of the main aspects of the Ciao modular compiler, ciaoc, which takes advantage of the characteristics of the Ciao Prolog module system to automatically perform sepárate and incremental compilation and efficiently build small, standalone executables with competitive run-time performance, ciaoc can also detect statically a larger number of programming errors. We also present a generic code processing library for handling modular programs, which provides an important part of the functionality of ciaoc. This library allows the development of program analysis and transformation tools in a way that is to some extent orthogonal to the details of module system design, and has been used in the implementation of ciaoc and other Ciao system tools. We also describe the different types of executables which can be generated by the Ciao compiler, which offer different tradeoffs between executable size, startup time, and portability, depending, among other factors, on the linking regime used (static, dynamic, lazy, etc.). Finally, we provide experimental data which illustrate these tradeoffs.

The ciao modular, standalone compiler and its generic program processing library

Ciao Prolog incorporates a module system which allows sepárate compilation and sensible creation of standalone executables. We describe some of the main aspects of the Ciao modular compiler, ciaoc, which takes advantage of the characteristics of the Ciao Prolog module system to automatically perform sepárate and incremental compilation and efficiently build small, standalone executables with competitive run-time performance, ciaoc can also detect statically a larger number of programming errors. We also present a generic code processing library for handling modular programs, which provides an important part of the functionality of ciaoc. This library allows the development of program analysis and transformation tools in a way that is to some extent orthogonal to the details of module system design, and has been used in the implementation of ciaoc and other Ciao system tools. We also describe the different types of executables which can be generated by the Ciao compiler, which offer different tradeoffs between executable size, startup time, and portability, depending, among other factors, on the linking regime used (static, dynamic, lazy, etc.). Finally, we provide experimental data which illustrate these tradeoffs.

Tools for constraint visualisation: The VIFID/TRIFID tool

Visualisation of program executions has been used in applications which include education and debugging. However, traditional visualisation techniques often fall short of expectations or are altogether inadequate for new programming paradigms, such as Constraint Logic Programming (CLP), whose declarative and operational semantics differ in some crucial ways from those of other paradigms. In particular, traditional ideas regarding the behaviour of data often cannot be lifted in a straightforward way to (C)LP from other families of programming languages. In this chapter we discuss techniques for visualising data evolution in CLP. We briefly review some previously proposed visualisation paradigms, and also propose a number of (to our knowledge) novel ones. The graphical representations have been chosen based on the perceived needs of a programmer trying to analyse the behaviour and characteristics of an execution. In particular, we concentrate on the representation of the run-time values of the variables, and the constraints among them. Given our interest in visualising large executions, we also pay attention to abstraction techniques, i.e., techniques which are intended to help in reducing the complexity of the visual information.

Modeling Reflective Bistability in Vertical-Cavity Semiconductor Optical Amplifiers

The characteristics of optical bistability in a vertical- cavity semiconductor optical amplifier (VCSOA) operated in reflection are reported. The dependences of the optical bistability in VCSOAs on the initial phase detuning and on the applied bias current are analyzed. The optical bistability is also studied for different numbers of superimposed periods in the top distributed bragg reflector (DBR) that conform the internal cavity of the device. The appearance of the X-bistable and the clockwise bistable loops is predicted theoretically in a VCSOA operated in reflection for the first time, to the best of our knowledge. Moreover, it is also predicted that the control of the VCSOA’s top reflectivity by the addition of new superimposed periods in its top DBR reduces by one order of magnitude the input power needed for the assessment of the X- and the clockwise bistable loop, compared to that required in in-plane semiconductor optical amplifiers. These results, added to the ease of fabricating two-dimensional arrays of this kind of device could be useful for the development of new optical logic or optical signal regeneration devices.

La videovigilancia : tecnologías actuales y aspectos sociopolíticos

En este Proyecto de fin de carrera titulado: LA VÍDEOVIGILANCIA: TECNOLOGÍAS ACTUALES Y ASPECTOS SOCIOPOLÍTICOS, tiene como objetivo hacer un estudio en los sistemas de Vídeovigilancia basado en cámaras-IP, con fines de seguridad, control o supervisión. Nos basaremos en exponer los sistemas Vídeovigilancia basados en cámara-IP actuales de ultima generación, cuya principal virtud de estos sistemas, es la comunicación con otros lugares, o espacios públicos como privados y poder visualizar tanto en vivo como en diferido lo que este pasando en ese lugar y en ese momento o haya pasado a través del protocolo de comunicación-IP. Se explicara desde el más básico al más complejo sistema de videovigilancia-IP, también explicaremos su puesta en practica mediante los múltiples interconexiones que estos conlleven. Llegando a este punto, se nos plantea las siguientes cuestiones que da origen a este PFC. Estos sistemas de Vídeovigilancia-IP, captan las imágenes por medio de las cámaras-IP, proporcionando su facilidad tanto de visionado/grabacion, como de control, ya que no es necesario estar presente e interactuando con otros sistemas digitales de diverso índole actuales, gracias al protocolo-IP. Estos sistemas-IP, tienen su puesta en práctica mediante las instalaciones requeridas ,estas podrán ser sencillas o muy complejas de todos los sistemas-IP. Debido al gran aumento masivo, las tecnologías actuales de diverso índole de cámaras-IP en materia de la vídeovigilancia en lugares públicos, y privados en nuestra sociedad actual, lo hace un medio particularmente invasivo y por ello resulta necesario tanto la concurrencia de condiciones que legitimen los tratamientos de datos de personas identificables, como la definición de los principios y garantías que deban aplicarse ya que estas, repercutirán sobre los derechos de las personas, lo que obligara a fijar ciertas garantías. Se nos plantea los casos en los que la captación y/o tratamiento de imágenes con fines de Vídeovigilancia que pertenezcan a personas identificadas o identificables, ha obligado a España, y según dispuesto por la Directiva 95/46/CE del Parlamento Europeo, a regularizar esta situación mediante la Ley Orgánica de Protección de Datos (LOPD) 15/1999 de 13 de diciembre, bajo los procedimientos del Estado español en materia sociopolítica, y dando vigor a esta ley, mediante la aprobación de la Instrucción 1/2006 de 8 de noviembre de 2006, cuyo máximo organismo es la Agencia española de Protección de Datos (AGPD). Una vez planteada la motivación y justificación del proyecto, se derivan unos objetivos a cumplir con la realización del mismo. Los objetivos del proyecto se pueden diferenciar en dos clases principalmente. Los objetivos principales y objetivos secundarios. Los objetivos principales de este PFC, nacen directamente de las necesidades planteadas originalmente en materia de Vídeovigilancia, tanto tecnológicamente basado en las cámaras-IP en la captación y/o tratamiento de imágenes, así como sociopolíticamente donde trataremos de describirlo mediante las indicaciones y criterios con casos prácticos y de cómo deben de aplicarse según la instrucción 1/2006 mediante la LOPD en materia de Vídeovigilancia, en cuanto a la protección de datos que puedan repercutir sobre el derecho de las personas. Por otra parte los objetivos secundarios, son la extensión del objetivo primario y son de orden cuantificador en este PFC, dando una explicación más exhaustiva del objetivo principal. ABSTRACT In this final year project, entitled: THE VIDEOSURVEILLANCE: CURRENT TECHNOLOGIES AND POLITICALSOCIALS ASPECTS, aims to make a study of video surveillance systems based on IP cameras, for security, control or supervision. We will rely on to expose the camera based video surveillance systems IP-current last generation, whose main virtue of these systems, is communication with other places, or public and private spaces and to view both live and time so this happening in that place and at that time or passed through-IP communication protocol. He explained from the most basic to the most complex-IP video surveillance system, also explain its implementation into practice through multiple interconnections that these entail. Arriving at this point, we face the following issues which gave rise to this PFC. These IP-video surveillance systems, captured images through IP-cameras, providing both ease of viewing / recording, as a control, since it is not necessary to be present and interacting with other digital systems such diverse today, thanks IP-protocol. These systems-IP, have their implementation through the facilities required, these can be simple or very complex all-IP video surveillance systems. Due to the large increase in mass, current technologies of different kinds of IP cameras for video surveillance in public places, and private in our society, it makes a particularly invasive and therefore attendance is necessary both conditions that legitimize data processing of identifiable people, as the definition of the principles and safeguards to be applied as these will impact on the rights of the people, which forced to set certain guarantees. We face those cases in which the uptake and / or image processing video surveillance purposes belonging to identified or identifiable, has forced Spain, and as required by Directive 95/46/EC of the European Parliament, to regularize this situation by the Organic Law on Data Protection (LOPD) 15/1999 of December 13, under the procedures of the Spanish State in sociopolitical, and giving effect to this Act, with the approval of the Instruction 1/2006 of 8 November 2006, the governing body is the Spanish Agency for Data Protection (AGPD). Once raised the motivation and justification for the project, resulting in meeting targets to achieve the same. Project objectives can be differentiated into two main classes, the main objectives and secondary objectives: The main objectives of this PFC, born directly from requirements originally raised for capturing both technologically imaging me and try to describe where sociopolitically, the details and criteria as case studies and should be applied according to the instruction 1 / 2006 by the LOPD on video surveillance system in terms of data protection that could impact on the right people. Moreover the secondary objectives are the extension of the primary and are of a quantifier in this PFC, giving a fuller explanation of the main objective.

Estimación de la peligrosidad sísmica mediante protocolos de juicios de expertos

Este trabajo estudia la aportación que los métodos de agregación de juicios de expertos pueden realizar en el cálculo de la peligrosidad sísmica de emplazamientos. Se han realizado cálculos en dos emplazamientos de la Península Ibérica: Mugardos (La Coruña) y Cofrentes (Valencia) que están sometidos a regímenes tectónicos distintos y que, además, alojan instalaciones industriales de gran responsabilidad. Las zonas de estudio, de 320 Km de radio, son independientes. Se ha aplicado un planteamiento probabilista a la estimación de la tasa anual de superación de valores de la aceleración horizontal de pico y se ha utilizado el Método de Montecarlo para incorporar a los resultados la incertidumbre presente en los datos relativos a la definición de cada fuente sismogenética y de su sismicidad. Los cálculos se han operado mediante un programa de ordenador, desarrollado para este trabajo, que utiliza la metodología propuesta por el Senior Seismic Hazard Analysis Commitee (1997) para la NRC. La primera conclusión de los resultados ha sido que la Atenuación es la fuente principal de incertidumbre en las estimaciones de peligrosidad en ambos casos. Dada la dificultad de completar los datos históricos disponibles de esta variable se ha estudiado el comportamiento de cuatro métodos matemáticos de agregación de juicios de expertos a la hora de estimar una ley de atenuación en un emplazamiento. Los datos de partida se han obtenido del Catálogo de Isosistas del IGN. Los sismos utilizados como variables raíz se han elegido con el criterio de cubrir uniformemente la serie histórica disponible y los valores de magnitud observados. Se ha asignado un panel de expertos particular a cada uno de los dos emplazamientos y se han aplicado a sus juicios los métodos de Cooke, equipesos, Apostolakis_Mosleh y Morris. Sus propuestas se han comparado con los datos reales para juzgar su eficacia y su facilidad de operación. A partir de los resultados se ha concluido que el método de Cooke ha mostrado el comportamiento más eficiente y robusto para ambos emplazamientos. Este método, además, ha permitido identificar, razonadamente, a aquellos expertos que no deberían haberse introducido en un panel. The present work analyses the possible contribution of the mathematical methods of aggregation in the assessment of Seismic Hazzard. Two sites, in the Iberian Peninsula, have been considered: Mugardos ( La Coruña) and Cofrentes (Valencia).Both of them are subjected to different tectonic regimes an both accommodate high value industrial plants. Their areas of concern, with radius of 320 Km, are not overlapping. A probabilistic approach has been applied in the assessment the annual probability of exceedence of the horizontal peak acceleration. The Montecarlo Method has allowed to transfer the uncertainty in the models and parameters to the final results. A computer program has been developed for this purpose. The methodology proposed by the Senior Seismic Analysis Committee (1997) for the NRC has been considered. Attenuation in Ground motion has been proved to be the main source of uncertainty in seismic hazard for both sites. Taking into account the difficulties to complete existing historical data in this subject the performance of four mathematical methods of aggregation has been studied. Original data have been obtained from the catalogs of the Spanish National Institute of Geography. The seismic events considered were chosen to cover evenly the historical records and the observed values of magnitude. A panel of experts have been applied to each site and four aggregation methods have been developed : equal weights, Cooke, Apostolakis-Mosleh and Morris The four proposals have been compaired with the actual data to judge their performance and ease of application. The results have shown that the Method of Cooke have proved the most efficient and robust for both sites. This method, besides, allow the reasoned identification of those experts who should be rejected from the panel

Diseño de una interfaz de representación gráfica de la base de datos de HRTF

El actual proyecto consiste en la creación de una interfaz gráfica de usuario (GUI) en entorno de MATLAB que realice una representación gráfica de la base de datos de HRTF (Head-Related Transfer Function). La función de transferencia de la cabeza es una herramienta muy útil en el estudio de la capacidad del ser humano para percibir su entorno sonoro, además de la habilidad de éste en la localización de fuentes sonoras en el espacio que le rodea. La HRTF biaural (terminología para referirse al conjunto de HRTF del oído izquierdo y del oído derecho) en sí misma, posee información de especial interés ya que las diferencias entre las HRTF de cada oído, conceden la información que nuestro sistema de audición utiliza en la percepción del campo sonoro. Por ello, la funcionalidad de la interfaz gráfica creada presenta gran provecho dentro del estudio de este campo. Las diferencias interaurales se caracterizan en amplitud y en tiempo, variando en función de la frecuencia. Mediante la transformada inversa de Fourier de la señal HRTF, se obtiene la repuesta al impulso de la cabeza, es decir, la HRIR (Head-Related Impulse Response). La cual, además de tener una gran utilidad en la creación de software o dispositivos de generación de sonido envolvente, se utiliza para obtener las diferencias ITD (Interaural Time Difference) e ILD (Interaural Time Difference), comúnmente denominados “parámetros de localización espacial”. La base de datos de HRTF contiene la información biaural de diferentes puntos de ubicación de la fuente sonora, formando una red de coordenadas esféricas que envuelve la cabeza del sujeto. Dicha red, según las medidas realizadas en la cámara anecoica de la EUITT (Escuela Universitaria de Ingeniería Técnica de Telecomunicación), presenta una precisión en elevación de 10º y en azimut de 5º. Los receptores son dos micrófonos alojados en el maniquí acústico llamado HATS (Hats and Torso Simulator) modelo 4100D de Brüel&Kjaer. Éste posee las características físicas que influyen en la percepción del entorno como son las formas del pabellón auditivo (pinna), de la cabeza, del cuello y del torso humano. Será necesario realizar los cálculos de interpolación para todos aquellos puntos no contenidos en la base de datos HRTF, este proceso es sumamente importante no solo para potenciar la capacidad de la misma sino por su utilidad para la comparación entre otras bases de datos existentes en el estudio de este ámbito. La interfaz gráfica de usuario está concebida para un manejo sencillo, claro y predecible, a la vez que interactivo. Desde el primer boceto del programa se ha tenido clara su filosofía, impuesta por las necesidades de un usuario que busca una herramienta práctica y de manejo intuitivo. Su diseño de una sola ventana reúne tanto los componentes de obtención de datos como los que hacen posible la representación gráfica de las HRTF, las HRIR y los parámetros de localización espacial, ITD e ILD. El usuario podrá ir alternando las representaciones gráficas a la vez que introduce las coordenadas de los puntos que desea visualizar, definidas por phi (elevación) y theta (azimut). Esta faceta de la interfaz es la que le otorga una gran facilidad de acceso y lectura de la información representada en ella. Además, el usuario puede introducir valores incluidos en la base de datos o valores intermedios a estos, de esta manera, se indica a la interfaz la necesidad de realizar la interpolación de los mismos. El método de interpolación escogido es el de la ponderación de la distancia inversa entre puntos. Dependiendo de los valores introducidos por el usuario se realizará una interpolación de dos o cuatro puntos, siendo éstos limítrofes al valor introducido, ya sea de phi o theta. Para añadir versatilidad a la interfaz gráfica de usuario, se ha añadido la opción de generar archivos de salida en forma de imagen de las gráficas representadas, de tal forma que el usuario pueda extraer los datos que le interese para cualquier valor de phi y theta. Se completa el presente proyecto fin de carrera con un trabajo de investigación y estudio comparativo de la función y la aplicación de las bases de datos de HRTF dentro del marco científico y de investigación. Esto ha hecho posible concentrar información relacionada a través de revistas científicas de investigación como la JAES (Journal of the Audio Engineering Society) o la ASA (Acoustical Society of America), además, del IEEE ( Institute of Electrical and Electronics Engineers) o la “Web of knowledge” entre otras. Además de realizar la búsqueda en estas fuentes, se ha optado por vías de información más comunes como Google Académico o el portal de acceso “Ingenio” a los todos los recursos electrónicos contenidos en la base de datos de la universidad. El estudio genera una ampliación en el conocimiento de la labor práctica de las HRTF. La mayoría de los estudios enfocan sus esfuerzos en mejorar la percepción del evento sonoro mediante su simulación en la escucha estéreo o multicanal. A partir de las HRTF, esto es posible mediante el análisis y el cálculo de datos como pueden ser las regresiones, siendo éstas muy útiles en la predicción de una medida basándose en la información de la actual. Otro campo de especial interés es el de la generación de sonido 3D. Mediante la base de datos HRTF es posible la simulación de una señal biaural. Se han diseñado algoritmos que son implementados en dispositivos DSP, de tal manera que por medio de retardos interaurales y de diferencias espectrales es posible llegar a un resultado óptimo de sonido envolvente, sin olvidar la importancia de los efectos de reverberación para conseguir un efecto creíble de sonido envolvente. Debido a la complejidad computacional que esto requiere, gran parte de los estudios coinciden en desarrollar sistemas más eficientes, llegando a objetivos tales como la generación de sonido 3D en tiempo real. ABSTRACT. This project involves the creation of a Graphic User Interface (GUI) in the Matlab environment which creates a graphic representation of the HRTF (Head-Related Transfer Function) database. The head transfer function is a very useful tool in the study of the capacity of human beings to perceive their sound environment, as well as their ability to localise sound sources in the area surrounding them. The binaural HRTF (terminology which refers to the HRTF group of the left and right ear) in itself possesses information of special interest seeing that the differences between the HRTF of each ear admits the information that our system of hearing uses in the perception of each sound field. For this reason, the functionality of the graphic interface created presents great benefits within the study of this field. The interaural differences are characterised in space and in time, varying depending on the frequency. By means of Fourier's transformed inverse of the HRTF signal, the response to the head impulse is obtained, in other words, the HRIR (Head-Related Impulse Response). This, as well as having a great use in the creation of software or surround sound generating devices, is used to obtain ITD differences (Interaural Time Difference) and ILD (Interaural Time Difference), commonly named “spatial localisation parameters”. The HRTF database contains the binaural information of different points of sound source location, forming a network of spherical coordinates which surround the subject's head. This network, according to the measures carried out in the anechoic chamber at the EUITT (School of Telecommunications Engineering) gives a precision in elevation of 10º and in azimuth of 5º. The receivers are two microphones placed on the acoustic mannequin called HATS (Hats and Torso Simulator) Brüel&Kjaer model 4100D. This has the physical characteristics which affect the perception of the surroundings which are the forms of the auricle (pinna), the head, neck and human torso. It will be necessary to make interpolation calculations for all those points which are not contained the HRTF database. This process is extremely important not only to strengthen the database's capacity but also for its usefulness in making comparisons with other databases that exist in the study of this field. The graphic user interface is conceived for a simple, clear and predictable use which is also interactive. Since the first outline of the program, its philosophy has been clear, based on the needs of a user who requires a practical tool with an intuitive use. Its design with only one window unites not only the components which obtain data but also those which make the graphic representation of the HRTFs possible, the hrir and the ITD and ILD spatial location parameters. The user will be able to alternate the graphic representations at the same time as entering the point coordinates that they wish to display, defined by phi (elevation) and theta (azimuth). The facet of the interface is what provides the great ease of access and reading of the information displayed on it. In addition, the user can enter values included in the database or values which are intermediate to these. It is, likewise, indicated to the interface the need to carry out the interpolation of these values. The interpolation method is the deliberation of the inverse distance between points. Depending on the values entered by the user, an interpolation of two or four points will be carried out, with these being adjacent to the entered value, whether that is phi or theta. To add versatility to the graphic user interface, the option of generating output files in the form of an image of the graphics displayed has been added. This is so that the user may extract the information that interests them for any phi and theta value. This final project is completed with a research and comparative study essay on the function and application of HRTF databases within the scientific and research framework. It has been possible to collate related information by means of scientific research magazines such as the JAES (Journal of the Audio Engineering Society), the ASA (Acoustical Society of America) as well as the IEEE (Institute of Electrical and Electronics Engineers) and the “Web of knowledge” amongst others. In addition to carrying out research with these sources, I also opted to use more common sources of information such as Academic Google and the “Ingenio” point of entry to all the electronic resources contained on the university databases. The study generates an expansion in the knowledge of the practical work of the HRTF. The majority of studies focus their efforts on improving the perception of the sound event by means of its simulation in stereo or multichannel listening. With the HRTFs, this is possible by means of analysis and calculation of data as can be the regressions. These are very useful in the prediction of a measure being based on the current information. Another field of special interest is that of the generation of 3D sound. Through HRTF databases it is possible to simulate the binaural signal. Algorithms have been designed which are implemented in DSP devices, in such a way that by means of interaural delays and wavelength differences it is possible to achieve an excellent result of surround sound, without forgetting the importance of the effects of reverberation to achieve a believable effect of surround sound. Due to the computational complexity that this requires, a great many studies agree on the development of more efficient systems which achieve objectives such as the generation of 3D sound in real time.

Valuation: Developer support for by-references to by-value type conversion.

Modern object oriented languages like C# and JAVA enable developers to build complex application in less time. These languages are based on selecting heap allocated pass-by-reference objects for user defined data structures. This simplifies programming by automatically managing memory allocation and deallocation in conjunction with automated garbage collection. This simplification of programming comes at the cost of performance. Using pass-by-reference objects instead of lighter weight pass-by value structs can have memory impact in some cases. These costs can be critical when these application runs on limited resource environments such as mobile devices and cloud computing systems. We explore the problem by using the simple and uniform memory model to improve the performance. In this work we address this problem by providing an automated and sounds static conversion analysis which identifies if a by reference type can be safely converted to a by value type where the conversion may result in performance improvements. This works focus on C# programs. Our approach is based on a combination of syntactic and semantic checks to identify classes that are safe to convert. We evaluate the effectiveness of our work in identifying convertible types and impact of this transformation. The result shows that the transformation of reference type to value type can have substantial performance impact in practice. In our case studies we optimize the performance in Barnes-Hut program which shows total memory allocation decreased by 93% and execution time also reduced by 15%.

Improved boundary elements in torsion problems

Since the epoch-making "memoir" of Saint-Venant in 1855 the torsion of prismatic and cilindrical bars has reduced to a mathematical problem: the calculation of an analytical function satisfying prescribed boundary values. For over one century, till the first applications of the F.E.M. to the problem, the only possibility of study in irregularly shaped domains was the beatiful, but limitated, theory of complex function analysis, several functional approaches and the finite difference method. Nevertheless in 1963 Jaswon published an interestingpaper which was nearly lost between the splendid F. E.M. boom. The method was extended by Rizzo to more complicated problems and definitively incorporated to the scientific community background through several lecture-notes of Cruse recently published, but widely circulated during past years. The work of several researches has shown the tremendous possibilities of the method which is today a recognized alternative to the well established F .E. procedure. In fact, the first comprehensive attempt to cover the method, has been recently published in textbook form. This paper is a contribution to the implementation of a difficulty which arises if the isoparametric elements concept is applicated to plane potential problems with sharp corners in the boundary domain. In previous works, these problems was avoided using two principal approximations: equating the fluxes round the corner or establishing a binode element (in fact, truncating the corner). The first approximation distortes heavily the solution in thecorner neighbourhood, and a great amount of element is neccesary to reduce its influence. The second is better suited but the price payed is increasing the size of the system of equations to be solved. In this paper an alternative formulation, consistent with the shape function chosen in the isoparametric representation, is presented. For ease of comprehension the formulation has been limited to the linear element. Nevertheless its extension to more refined elements is straight forward. Also a direct procedure for the assembling of the equations is presented in an attempt to reduce the in-core computer requirements.