Systematic study of the temperature dependence of the saturation magnetization in Fe, Fe-Ni and Co-based amorphous alloys

Magnetization versus temperature in the temperature interval 2-200 K was measured for amorphous alloys of three different compositions: Fe 81.5B14.5Si4, Fe40Ni38 Mo4B18, and Co70Fe5Ni 2Mo3B5Si15. The measurements were performed by means of a SQUID (superconducting quantum interference device) magnetometer. The aim was to extract information about the different mechanisms contributing to thermal demagnetization. A powerful data analysis technique based on successive minimization procedures has demonstrated that Stoner excitations of the strong ferromagnetic type play a significant role in the Fe-Ni alloy studied. The Fe-rich and Co-rich alloys do not show a measurable contribution from single-particle excitations.

Concurrent or sequential adjuvant letrozole and radiotherapy after conservative surgery for early-stage breast cancer (CO-HO-RT): a phase 2 randomised trial.

BACKGROUND: Letrozole radiosensitises breast cancer cells in vitro. In clinical settings, no data exist for the combination of letrozole and radiotherapy. We assessed concurrent and sequential radiotherapy and letrozole in the adjuvant setting. METHODS: This phase 2 randomised trial was undertaken in two centres in France and one in Switzerland between Jan 12, 2005, and Feb 21, 2007. 150 postmenopausal women with early-stage breast cancer were randomly assigned after conserving surgery to either concurrent radiotherapy and letrozole (n=75) or sequential radiotherapy and letrozole (n=75). Randomisation was open label with a minimisation technique, stratified by investigational centres, chemotherapy (yes vs no), radiation boost (yes vs no), and value of radiation-induced lymphocyte apoptosis (< or = 16% vs >16%). Whole breast was irradiated to a total dose of 50 Gy in 25 fractions over 5 weeks. In the case of supraclavicular and internal mammary node irradiation, the dose was 44-50 Gy. Letrozole was administered orally once daily at a dose of 2.5 mg for 5 years (beginning 3 weeks pre-radiotherapy in the concomitant group, and 3 weeks post-radiotherapy in the sequential group). The primary endpoint was the occurrence of acute (during and within 6 weeks of radiotherapy) and late (within 2 years) radiation-induced grade 2 or worse toxic effects of the skin. Analyses were by intention to treat. This study is registered with ClinicalTrials.gov, number NCT00208273. FINDINGS: All patients were analysed apart from one in the concurrent group who withdrew consent before any treatment. During radiotherapy and within the first 12 weeks after radiotherapy, 31 patients in the concurrent group and 31 in the sequential group had any grade 2 or worse skin-related toxicity. The most common skin-related adverse event was dermatitis: four patients in the concurrent group and six in the sequential group had grade 3 acute skin dermatitis during radiotherapy. At a median follow-up of 26 months (range 3-40), two patients in each group had grade 2 or worse late effects (both radiation-induced subcutaneous fibrosis). INTERPRETATION: Letrozole can be safely delivered shortly after surgery and concomitantly with radiotherapy. Long-term follow-up is needed to investigate cardiac side-effects and cancer-specific outcomes. FUNDING: Novartis Oncology France.

Regulation of the activity of DnaA and its role during the cell cycle of caulobacter crescentus

The initiation of chromosomal replication must be tightly regulated so that the genome is replicated only once per cell cycle. In most bacteria, DnaA binds to the origin of replication and initiates chromosomal replication. DnaA is a dual-function protein that also acts as an important transcription factor that regulates the expression of many genes in bacteria. Thus, understanding how this protein is regulated during the bacterial cell cycle is of major importance. The α-proteobacterium Caulobacter crescentus is an excellent model to study the bacterial cell cycle, mainly because it is possible to isolate synchronized cell cultures and because it initiates the replication of its chromosome once per cell cycle and at a specific time of the cell cycle. This latest feature is of special interest for the major aim of my thesis work, which focused on the temporal and spatial regulation of the activity of the essential DnaA protein in C. crescentus. In Escherichia coli, the Hda protein converts ATP-DnaA into ADP- DnaA by stimulating the ATPase activity of DnaA, to prevent over-initiation of chromosome replication. We propose that there exists a similar mechanism in C. crescentus, which is not only involved in the temporal control of chromosome replication, but also in the control of gene expression. First, we provided evidences indicating that the hydrolysis of the ATP bound to DnaA is essential for the viability of C. crescentus. Our results suggest that ATP-DnaA promotes the initiation of chromosome replication, since we found that cells over-expressing a DnaA protein with a mutated ATPase domain, DnaA(R357A), over-initiated chromosome replication, unlike cells expressing the wild-type DnaA protein at similar levels. By contrast, the DnaA(R357A) protein was less active than DnaA in promoting the transcription of three essential genes, suggesting that these may be more efficiently activated by ADP-DnaA than ATP-DnaA. We propose that the ATP-DnaA to ADP-DnaA switch down-regulates the initiation of DNA replication while activating the transcription of several essential genes involved in subsequent cell cycle events. Second, we studied the role of the HdaA protein, homologous to Hda, in promoting the ATP- DnaA to ADP-DnaA switch in C. crescentus. HdaA is essential for viability and its depletion in the cell leads to an over-replication of the chromosome, indicating that HdaA is a negative regulator of DNA replication. HdaA dynamically co-localizes with the replisome. In this work, we identified DnaN, the β-clamp of the DNA polymerase, as the replisome component that interacts directly with HdaA and that recruits HdaA to the replisome in live C. crescentus cells. We also showed that a mutant HdaA protein that cannot interact or co-localize with DnaN is not functional, indicating that HdaA is probably activated by DnaN. However, we found that another non-functional HdaA protein, mutated in the conserved Arginine finger of its AAA+ domain, was able to localize at the replisome, suggesting that the AAA+ domain of HdaA exerts its essential function after the recruitment of HdaA to the replisome. We propose that HdaA stimulates the ATPase activity of DnaA once DNA replication is ongoing, via its interaction with DnaN and the activity of the two conserved R fingers of DnaA and HdaA. Finally, we created different strains in which HdaA, DnaN or DnaA were over-produced. We observed that the over-production of HdaA seems to lead to a delay in chromosome replication, while the over-production of DnaN had an opposite effect. Our results also indicate that the over-production of DnaA may intensify the over-initiation phenotype of cells depleted for HdaA. We conclude that the dynamic interplay of HdaA and DnaN in the cell contributes to regulating the ATP-DnaA/ADP-DnaA ratio in the cell, to ensure once per cell cycle initiation of chromosomal replication in C. crescentus. Altogether, our work provided important information on the regulation of the activity of DnaA in C. crescentus. Since DnaA, HdaA and DnaN are well-conserved proteins, most of our findings are useful to understand how chromosome replication and gene expression are controlled by DnaA in many other bacterial species. - L'initiation de la réplication des chromosomes doit être précisément régulée de telle sorte que le génome ne soit répliqué qu'une seule fois par cycle cellulaire. Chez la plupart des bactéries, DnaA se lie à l'origine de réplication du chromosome et en initie sa réplication. DnaA est aussi un facteur de transcription qui régule l'expression de nombreux gènes bactériens. De ce fait, il est très important de comprendre comment DnaA est régulée au cours du cycle cellulaire bactérien. L'a-protéobactérie Caulobacter crescentus est un excellent modèle pour étudier le cycle cellulaire bactérien, essentiellement parce qu'il est aisé d'isoler des populations de cellules synchronisées à la même étape du cycle cellulaire et parce que cette bactérie n'initie la réplication de son chromosome qu'une seule fois et à un moment précis de son cycle. Cette dernière caractéristique est particulièrement pertinente pour l'objectif de mon travail doctoral, qui consistait à comprendre comment l'activité de la protéine essentielle DnaA est régulée dans l'espace et dans le temps chez C. crescentus. Chez Escherichia coli, la protéine Hda convertie DnaA-ATP en DnaA-ADP en stimulant l'activité ATPasique de DnaA, ce qui empêche la sur-initiation de la réplication du chromosome. Nous proposons qu'un mécanisme similaire existe chez C. crescentus. Il serait non seulement nécessaire au contrôle de la réplication du chromosome, mais aussi au contrôle de l'expression de certains gènes. Dans un premier temps, nous avons mis en évidence le fait que l'hydrolyse de l'ATP lié à DnaA est un processus essentiel à la viabilité de C. crescentus. Nos résultats suggèrent que DnaA-ATP initie la réplication du chromosome, comme nous avons observé que des cellules qui sur-expriment une protéine DnaA(R357A) mutée sans domaine ATPasique fonctionnel, sur-initie la réplication de leur chromosome, contrairement aux cellules qui sur-expriment la protéine DnaA sauvage à des niveaux équivalents. Au contraire, la protéine DnaA(R357A) était moins active que la protéine DnaA sauvage pour promouvoir la transcription de trois gènes essentiels, ce qui suggère que ces derniers sont peut-être plus efficacement activés par DnaA-ADP que DnaA-ATP. Nous proposons que la conversion de DnaA-ATP en DnaA-ADP réprime l'initiation de la réplication, tandis qu'elle active la transcription de plusieurs gènes impliqués dans des étapes plus tardives du cycle cellulaire. Dans un deuxième temps, nous avons étudié le rôle de la protéine HdaA, homologue à Hda, dans la conversion de DnaA-ATP en DnaA-ADP chez C. crescentus. Cette protéine est essentielle à la viabilité de C. crescentus et sa déplétion donne des cellules qui sur-initient la réplication de leur chromosome, suggérant que HdaA est un répresseur de la réplication du chromosome. HdaA co-localise de manière dynamique avec le réplisome. Lors de mon travail doctoral, nous avons démontré que DnaN, le β-clamp de l'ADN polymérase, est l'élément qui recrute HdaA au réplisome in vivo. Nous avons aussi montré qu'une protéine HdaA mutante qui ne peut pas interagir ou co-localiser avec DnaN, n'est pas fonctionnelle, ce qui suggère que HdaA est activée par DnaN. Nous avons néanmoins aussi isolé une autre protéine HdaA non fonctionnelle, dont une arginine conservée de son domaine AAA+ était mutée, mais qui pouvait toujours co-localiser avec le réplisome, ce qui suggère que le domaine AAA+ de HdaA est nécessaire après le recrutement de HdaA au réplisome. Nous proposons que HdaA stimule l'activité ATPasique de DnaA qu'une fois que la réplication a commencé, grâce à son interaction avec DnaN et aux deux arginines conservées des protéines HdaA et DnaA. Finalement, nous avons construit différentes souches sur-exprimant HdaA, DnaN ou DnaA. Nous avons observé que la sur-production de HdaA retarde la réplication du chromosome, tandis que la sur-production de DnaN a un effet opposé. Nos observations suggèrent aussi que la sur-expression de DnaA dans des cellules déplétées pour HdaA aggrave leur phénotype de sur-initiation. Nous en concluons que HdaA et DnaN collaborent étroitement et de manière dynamique pour réguler le rapport DnaA-ATP/DnaA-ADP dans la cellule, pour s'assurer que la réplication du chromosome ne soit initiée qu'une seule fois par cycle cellulaire chez C. crescentus. Globalement, notre travail a mis en évidence des informations importantes sur la régulation de l'activité de DnaA chez C. crescentus. Comme DnaA, HdaA et DnaN sont des protéines très conservées, la plupart de nos découvertes sont utiles pour mieux comprendre comment la réplication du chromosome bactérien et l'expression des gènes sont contrôlées par DnaA chez de nombreuses autres espèces bactériennes.

Report on theorerical results of power generation and conversion

Experimental results of a new controller able to support bidirectional power flow in a full-bridge rectifier with boost-like topology are obtained. The controller is computed using port Hamiltonian passivity techniques for a suitable generalized state space averaging truncation system, which transforms the control objectives, namely constant output voltage dc-bus and unity input power factor, into a regulation problem. Simulation results for the full system show the essential correctness of the simplifications introduced to obtain the controller, although some small experimental discrepancies point to several aspects that need further improvement.

Pyroelectric conversion: harvesting energy from temperature fluctuations

Peer reviewed

Early intervention for conversion disorder: neurologists and psychiatrists working together

It has been shown that for the reaction catalyzed by "biodegradative" L-threonine dehydratase from E. coli strains K-12 and 980 in 0.5 M phosphate-carbonate buffer, pH 8.4 and pH 9.5, the plots of initial reaction rate (v) versus the initial substrate concentration ([S]0 are characterized by several inflection points, i. e. an intermediate plateau. The plot of v versus the allosteric activator (AMP) concentration have very complicated shapes: there are several inflection points, and also the maximum at L-threonine concentration equal to 3-10(2) and 5-10(-2) M. High AMP concentrations inhibit the enzyme at high substrate concentrations. The reduced glutathion dose not influence the enzyme and does not alter the activating effect of AMP. On the basis of the data obtained it is proposed that the substrate and AMP shift the equilibrium between multiple oligomeric enzyme forms differing in catalytic activity and kinetic manifestations of allosteric interactions between the active and allosteric AMP-binding sites towards polymerization. Thus, the functioning the enzyme under study is discussed in the frames of the model of dissociating regulatory enzymes with multiple intermediate oligomeric forms.

Up-conversion effect of Er- and Yb-doped ZnO thin films

Visible up-conversion in ZnO:Er and ZnO:Er:Yb thin films deposited by RF magnetron sputtering under different O2-rich atmospheres has been studied. Conventional photoluminescence (325 nm laser source) and up-conversion (980 nm laser source) have been performed in the films before and after an annealing process at 800 °C. The resulting spectra demonstrate that the thermal treatment, either during or post-deposition, activates optically the Er3+ ions, being the latter process much more efficient. Moreover, the atmosphere during deposition was also found to be an important parameter, as the deposition under O2 flow increases the optical activity of Er+3 ions. In addition, the inclusion of Yb3+ ions into the films has shown an enhancement of the visible up-conversion emission at 660 nm by a factor of 4, which could be associated to either a better energy transfer from the 2F5/2 Yb level to the 4I11/2 Er one, or to the prevention of having Er2O3 clustering in the films.

Conflict and co-operation in ant societies

Cette thèse se propose d?étudier les forces évolutives qui influencent la bal- ance entre coopération et conflit. Deux exemples sont analysés en détail, les sociétés d?insectes et l?association entre la fourmi Formica exsecta et son sym- bionte intracellulaire Wolbachia. Chacune de ces deux associations animales est caractérisée par la coexistence de coopération et de conflit. Les colonies d?insectes sociaux sont un exemple typique de coopération. Néanmoins, la détermination haplodiploïde du sexe crée des apparentements asymétriques entre les membres de la colonie qui se traduisent par des con- flits entre reines et ouvrières. Un des conflits les plus importants porte sur le sexe-ratio, l?investissement optimal en sexués males et femelles étant équilibré pour la reine, mais biaisé en faveur des femelles pour les ouvrières. Jusqu?ici, les modèles étudiant ce conflit se basaient uniquement sur les asymétries d?ap- parentement. La première partie de cette thèse (Chapitres 1 et 2) propose d?introduire dans des modèles de sexe-ratio les mécanismes proximaux utilisés par les deux parties pour influencer le sexe-ratio. Ces mécanismes, par leurs ef- fets négatifs sur la productivité de la colonie, peuvent entraîner des déviations importantes du sexe-ratio par rapport à la valeur prédite par des modèles clas- siques. De plus, la prise en compte de ces mécanismes nous permet d?étudier dans quelle mesure les parties opposées sont sélectionnées pour influencer le sexe-ratio. Enfin, les modèles génèrent des prédictions quant à l?issue du con- flit, c?est-à-dire un compromis où reines et ouvrières partagent le contrôle de l?investissement. La seconde partie du travail porte sur l?infection de la fourmi Formica ex- secta par le symbionte cytoplasmique Wolbachia. Ce symbionte, présent chez un grand nombre d?espèces d?Arthropodes, est transmis maternellement. Afin de se répandre dans la population d?hôtes, Wolbachia manipule la physiolo- gie reproductive de l?organisme qui l?abrite. Le Chapitre 3 décrit une étude consacrée aux variations du sexe-ratio produit dans des colonies de fourmis? en fonction de la présence ou de l?absence de Wolbachia. Le Chapitre 4 étudie l?association entre les lignées du symbionte et les haplotypes mitochondriaux des hôtes. L?étude de l?association entre les deux éléments maternellement transmis est d?un intérêt particulier chez Formica exsecta car le taux de migra- tion femelle très faible engendre une forte strucure génétique mitochondriale.

Formation and Control of Trace Metal Emissions in Co-Firing of Biomass, Peat, and Wastes in Fluidised Bed Combustors

Environmentally harmful consequences of fossil fuel utilisation andthe landfilling of wastes have increased the interest among the energy producers to consider the use of alternative fuels like wood fuels and Refuse-Derived Fuels, RDFs. The fluidised bed technology that allows the flexible use of a variety of different fuels is commonly used at small- and medium-sized power plants ofmunicipalities and industry in Finland. Since there is only one mass-burn plantcurrently in operation in the country and no intention to build new ones, the co-firing of pre-processed wastes in fluidised bed boilers has become the most generally applied waste-to-energy concept in Finland. The recently validated EU Directive on Incineration of Wastes aims to mitigate environmentally harmful pollutants of waste incineration and co-incineration of wastes with conventional fuels. Apart from gaseous flue gas pollutants and dust, the emissions of toxic tracemetals are limited. The implementation of the Directive's restrictions in the Finnish legislation is assumed to limit the co-firing of waste fuels, due to the insufficient reduction of the regulated air pollutants in the existing flue gas cleaning devices. Trace metals emission formation and reduction in the ESP, the condensing wet scrubber, the fabric filter, and the humidification reactor were studied, experimentally, in full- and pilot-scale combustors utilising the bubbling fluidised bed technology, and, theoretically, by means of reactor model calculations. The core of the model is a thermodynamic equilibrium analysis. The experiments were carried out with wood chips, sawdust, and peat, and their refuse-derived fuel, RDF, blends. In all, ten different fuels or fuel blends were tested. Relatively high concentrations of trace metals in RDFs compared to the concentrations of these metals in wood fuels increased the trace metal concentrations in the flue gas after the boiler ten- to hundred-folds, when RDF was co-fired with sawdust in a full-scale BFB boiler. In the case of peat, lesser increase in trace metal concentrations was observed, due to the higher initial trace metal concentrations of peat compared to sawdust. Despite the high removal rate of most of the trace metals in the ESP, the Directive emission limits for trace metals were exceeded in each of the RDF co-firing tests. The dominat trace metals in fluegas after the ESP were Cu, Pb and Mn. In the condensing wet scrubber, the flue gas trace metal emissions were reduced below the Directive emission limits, whenRDF pellet was used as a co-firing fuel together with sawdust and peat. High chlorine content of the RDFs enhanced the mercuric chloride formation and hence the mercury removal in the ESP and scrubber. Mercury emissions were lower than theDirective emission limit for total Hg, 0.05 mg/Nm3, in all full-scale co-firingtests already in the flue gas after the ESP. The pilot-scale experiments with aBFB combustor equipped with a fabric filter revealed that the fabric filter alone is able to reduce the trace metal concentrations, including mercury, in the flue gas during the RDF co-firing approximately to the same level as they are during the wood chip firing. Lower trace metal emissions than the Directive limits were easily reached even with a 40% thermal share of RDF co-firing with sawdust.Enrichment of trace metals in the submicron fly ash particle fraction because of RDF co-firing was not observed in the test runs where sawdust was used as the main fuel. The combustion of RDF pellets with peat caused an enrichment of As, Cd, Co, Pb, Sb, and V in the submicron particle mode. Accumulation and release oftrace metals in the bed material was examined by means of a bed material analysis, mass balance calculations and a reactor model. Lead, zinc and copper were found to have a tendency to be accumulated in the bed material but also to have a tendency to be released from the bed material into the combustion gases, if the combustion conditions were changed. The concentration of the trace metal in the combustion gases of the bubbling fluidised bed boiler was found to be a summary of trace metal fluxes from three main sources. They were (1) the trace metal flux from the burning fuel particle (2) the trace metal flux from the ash in the bed, and (3) the trace metal flux from the active alkali metal layer on the sand (and ash) particles in the bed. The amount of chlorine in the system, the combustion temperature, the fuel ash composition and the saturation state of the bed material in regard to trace metals were discovered to be key factors affecting therelease process. During the co-firing of waste fuels with variable amounts of e.g. ash and chlorine, it is extremely important to consider the possible ongoingaccumulation and/or release of the trace metals in the bed, when determining the flue gas trace metal emissions. If the state of the combustion process in regard to trace metals accumulation and/or release in the bed material is not known,it may happen that emissions from the bed material rather than the combustion of the fuel in question are measured and reported.

Ion-exchange resins as stationary phase in reactive chromatography

Dynamic behavior of bothisothermal and non-isothermal single-column chromatographic reactors with an ion-exchange resin as the stationary phase was investigated. The reactor performance was interpreted by using results obtained when studying the effect of the resin properties on the equilibrium and kinetic phenomena occurring simultaneously in the reactor. Mathematical models were derived for each phenomenon and combined to simulate the chromatographic reactor. The phenomena studied includes phase equilibria in multicomponent liquid mixture¿ion-exchange resin systems, chemicalequilibrium in the presence of a resin catalyst, diffusion of liquids in gel-type and macroporous resins, and chemical reaction kinetics. Above all, attention was paid to the swelling behavior of the resins and how it affects the kinetic phenomena. Several poly(styrene-co-divinylbenzene) resins with different cross-link densities and internal porosities were used. Esterification of acetic acid with ethanol to produce ethyl acetate and water was used as a model reaction system. Choosing an ion-exchange resin with a low cross-link density is beneficial inthe case of the present reaction system: the amount of ethyl acetate as well the ethyl acetate to water mole ratio in the effluent stream increase with decreasing cross-link density. The enhanced performance of the reactor is mainly attributed to increasing reaction rate, which in turn originates from the phase equilibrium behavior of the system. Also mass transfer considerations favor the use ofresins with low cross-link density. The diffusion coefficients of liquids in the gel-type ion-exchange resins were found to fall rapidly when the extent of swelling became low. Glass transition of the polymer was not found to significantlyretard the diffusion in sulfonated PS¿DVB ion-exchange resins. It was also shown that non-isothermal operation of a chromatographic reactor could be used to significantly enhance the reactor performance. In the case of the exothermic modelreaction system and a near-adiabatic column, a positive thermal wave (higher temperature than in the initial state) was found to travel together with the reactive front. This further increased the conversion of the reactants. Diffusion-induced volume changes of the ion-exchange resins were studied in a flow-through cell. It was shown that describing the swelling and shrinking kinetics of the particles calls for a mass transfer model that explicitly includes the limited expansibility of the polymer network. A good description of the process was obtained by combining the generalized Maxwell-Stefan approach and an activity model that was derived from the thermodynamics of polymer solutions and gels. The swelling pressure in the resin phase was evaluated by using a non-Gaussian expression forthe polymer chain length distribution. Dimensional changes of the resin particles necessitate the use of non-standard mathematical tools for dynamic simulations. A transformed coordinate system, where the mass of the polymer was used as a spatial variable, was applied when simulating the chromatographic reactor columns as well as the swelling and shrinking kinetics of the resin particles. Shrinking of the particles in a column leads to formation of dead volume on top of the resin bed. In ordinary Eulerian coordinates, this results in a moving discontinuity that in turn causes numerical difficulties in the solution of the PDE system. The motion of the discontinuity was eliminated by spanning two calculation grids in the column that overlapped at the top of the resin bed. The reactive and non-reactive phase equilibrium data were correlated with a model derived from thethermodynamics of polymer solution and gels. The thermodynamic approach used inthis work is best suited at high degrees of swelling because the polymer matrixmay be in the glassy state when the extent of swelling is low.