Mechanical vs. electrical hysteresis of carbon nanotube/styrene-butadiene-styrene composites and their influence in the electromechanical response

The interesting properties of thermoplastics elastomers can be combined with carbon nanotubes (CNT) for the development of large strain piezoresistive composites for sensor applications. Piezoresistive properties of the composites depend on CNT content, with the gauge factor increasing for concentrations around the percolation threshold, mechanical and electrical hysteresis. The SBS copolymer composition (butadiene/styrene ratio) influences the mechanical and electrical hysteresis of composites and, therefore, the piezoresistive response. This work reports on the electrical and mechanical response of CNT/SBS composites with 4%wt nanofiller content, due to the larger electromechanical response. C401 and C540 SBS copolymers with 80% and 60% butadiene content, respectively have been selected. The copolymer with larger amount of soft phase (C401) shows a rubber-like mechanical behavior, with mechanical hysteresis increasing linearly with strain until 100% strain. The copolymer with the larger amount of hard phase (C540) just shows rubber-like behavior for low strains. The piezoresistive sensibility is similar for both composites for low strains, with a GF≈ 5 for 5% strain. The electrical hysteresis shows opposite behavior than the mechanical hysteresis, increasing with strain for both composites, but with higher increase for softer copolymer, C401. The GF increases with increasing strain, but this increase is larger for composites with lower amounts of soft phase due to the distinct initial modulus and deformation of the soft and hard phases of the copolymer. The soft phase shows larger strain under a given stress than the harder phase and the conductive pathway rearrangements in the composites are different for both phases, the harder copolymer (C540) showing higher piezoresistive sensibility, GF≈ 18, for 20% strain.

Microstructure and mechanical properties of carbon nanotube reinforced cementitious composites developed using a novel dispersion technique

The authors also acknowledge Centre for Textile Science and Technology (University of Minho) and FIBRENAMICS PLATFORMfor providing required conditions for this research. Sincere thanks are also due to Mr. Pedro Samuel Leite and Mr. Carlos Jesus for their kind help in sample preparation and testing.

Search for production of vector-like quark pairs and of four top quarks in the lepton-plus-jets final state in pp collisions at root 8=8 TeV with the ATLAS detector

A search for pair production of vector-like quarks, both up-type (T) and down-type (B), as well as for four-top-quark production, is presented. The search is based on pp collisions at s√=8 TeV recorded in 2012 with the ATLAS detector at the CERN Large Hadron Collider and corresponding to an integrated luminosity of 20.3 fb−1. Data are analysed in the lepton-plus-jets final state, characterised by an isolated electron or muon with high transverse momentum, large missing transverse momentum and multiple jets. Dedicated analyses are performed targeting three cases: a T quark with significant branching ratio to a W boson and a b-quark (TT¯→Wb+X), and both a T quark and a B quark with significant branching ratio to a Higgs boson and a third-generation quark (TT¯→Ht+X and BB¯→Hb+X respectively). No significant excess of events above the Standard Model expectation is observed, and 95% CL lower limits are derived on the masses of the vector-like T and B quarks under several branching ratio hypotheses assuming contributions from T→Wb, Zt, Ht and B→Wt, Zb, Hb decays. The 95% CL observed lower limits on the T quark mass range between 715 GeV and 950 GeV for all possible values of the branching ratios into the three decay modes, and are the most stringent constraints to date. Additionally, the most restrictive upper bounds on four-top-quark production are set in a number of new physics scenarios.

Observation and measurements of the production of prompt and non-prompt J/ψ mesons in association with a Z boson in pp collisions at s√ = 8 TeV with the ATLAS detector

The production of a Z boson in association with a J/ψ meson in proton--proton collisions probes the production mechanisms of quarkonium and heavy flavour in association with vector bosons, and allows studies of multiple parton scattering. Using 20.3fb−1 of data collected with the ATLAS experiment at the LHC, in pp collisions at s√=8 TeV, the first measurement of associated Z+J/ψ production is presented for both prompt and non-prompt J/ψ production, with both signatures having a significance in excess of 5σ. The inclusive production cross-sections for Z boson production (in μ+μ− or e+e− decay modes) in association with prompt and non-prompt J/ψ(→μ+μ−) are measured relative to the inclusive production rate of Z bosons in the same fiducial volume to be (88±16±6)×10−8 and (157±22±10)×10−8 respectively. Normalised differential production cross-sections are also determined as a function of the J/ψ transverse momentum. The fraction of signal events arising from single and double parton scattering is estimated, and a lower limit of 5.3 (3.7)mb at 68 (95) confidence level is placed on the effective cross-section regulating double parton interactions.

Search for anomalous production of prompt same-sign lepton pairs and pair-produced doubly charged Higgs bosons with s√ = 8 TeV pp collisions using the ATLAS detector

A low-background inclusive search for new physics in events with same-sign dileptons is presented. The search uses proton--proton collisions corresponding to 20.3 fb−1 of integrated luminosity taken in 2012 at a centre-of-mass energy of 8 TeV with the ATLAS detector at the LHC. Pairs of isolated leptons with the same electric charge and large transverse momenta of the type e±e±,e±μ±, and μ±μ± are selected and their invariant mass distribution is examined. No excess of events above the expected level of Standard Model background is found. The results are used to set upper limits on the cross sections for processes beyond the Standard Model. Limits are placed as a function of the dilepton invariant mass within a fiducial region corresponding to the signal event selection criteria. Exclusion limits are also derived for a specific model of doubly charged Higgs boson production.

Search for production of WW/WZ resonances decaying to a lepton, neutrino and jets in pp collisions at s√ = 8 TeV with the ATLAS detector

A search is presented for a narrow diboson resonances decaying to WW or WZ in the final state where one W boson decays leptonically (to an electron or a muon plus a neutrino) and the other W/Z boson decays hadronically. The analysis is performed using an integrated luminosity of 20.3 fb−1 of pp collisions at s√ = 8 TeV collected by the ATLAS detector at the LHC. No evidence for resonant diboson production is observed, and resonance masses below 700 GeV and 1490 GeV are excluded at 95% confidence level for the spin-2 Randall-Sundrum bulk graviton G∗ with coupling constant of 1.0 and the extended gauge model W′ boson respectively.

Biosynthetic production of curcuminoids

Curcuminoids are natural phenylpropanoids from plants that have been reported as potential cancer-fighting drugs. Nevertheless, these compounds present a poor bioavailability. Cellular uptake is low and curcuminoids are quickly metabolized once inside the cell, requiring repetitive oral doses to achieve an effective concentration for therapeutic activity [1]. Herein, we report an engineered artificial pathway for the production of curcuminoids in Escherichia coli. Arabidopsis thaliana 4-coumaroyl-CoA ligase and Curcuma longa diketide-CoA synthase (DCS) and curcumin synthase (CURS1) were used and 188 µM (70 mg/L) of curcumin was obtained from ferulic acid [2]. Bisdemethoxycurcumin and demethoxycurcumin were also produced, but in lower concentrations, by feeding p-coumaric acid or a mixture of p-coumaric acid and ferulic acid, respectively. Additionally, curcuminoids were produced from tyrosine through the caffeic acid pathway. To produce caffeic acid, tyrosine ammonia lyase from Rhodotorula glutinis and 4-coumarate 3-hydroxylase from Saccharothrix espanaensis were used [3]. Caffeoyl-CoA 3-O-methyl-transferase from Medicago sativa was used to convert caffeoyl-CoA to feruloyl-CoA. Using caffeic acid, p-coumaric acid or tyrosine as a substrate, 3.9, 0.3, and 0.2 µM of curcumin were produced, respectively. This is the first report on the use of DCS and CURS1 in vivo to produce curcuminoids. In addition, curcumin, the most studied curcuminoid for therapeutic purposes and considered in many studies as the most potent and active, was produced by feeding tyrosine using a pathway involving caffeic acid. We anticipate that by using a tyrosine overproducing strain, curcumin can be produced in E. coli without the need of adding expensive precursors to the medium, thus decreasing the production cost. Therefore, this alternative pathway represents a step forward in the heterologous production of curcumin using E. coli. Aiming at greater production titers and yields, the construction of this pathway in another model organism such as Saccharomyces cerevisiae is being considered.

Measurement of the production of neighbouring jets in lead-lead collisions at √sNN=2.76 TeV with the ATLAS detector

This Letter presents measurements of correlated production of nearby jets in Pb+Pb collisions at sNN−−−√=2.76 TeV using the ATLAS detector at the Large Hadron Collider. The measurement was performed using 0.14 nb−1 of data recorded in 2011. The production of correlated jet pairs was quantified using the rate, RΔR, of ``neighbouring'' jets that accompany ``test'' jets within a given range of angular distance, ΔR, in the pseudorapidity--azimuthal angle plane. The jets were measured in the ATLAS calorimeter and were reconstructed using the anti-kt algorithm with radius parameters d=0.2, 0.3, and 0.4. RΔR was measured in different Pb+Pb collision centrality bins, characterized by the total transverse energy measured in the forward calorimeters. A centrality dependence of RΔR is observed for all three jet radii with RΔR found to be lower in central collisions than in peripheral collisions. The ratios formed by the RΔR values in different centrality bins and the values in the 40--80 % centrality bin are presented.

Protected environments and substrates for production of genipap seedlings

Genipap (Genipa americana L., Rubiaceae ) is a native Brazilian species and can be used in the recovery of degraded forest areas or for food supply. In order for the species to reach its potential, production of high quality seedlings is essential. The objective of this study was to evaluate genipap seedlings in protected environments and different substrates. The environments tested were: (1) a greenhouse with polyethylene film in the top, with aluminized screen (Aliminet®) of 50%-shading under this film, and lateral sides covered with 50%-shading nylon net (Sombrite®), (2) a shaded hut, all sides covered with 50%-shading nylon net (Sombrite®), and (3) a nursery shelter, with all lateral sides uncovered and the roof covered with leaves of buriti (Mauritia flexuosa). In these environments the following substrates were tested: 50% cattle manure + 50% cassava foliage, 50% cattle manure + 50% Vida Verde®, 50% cattle manure + 50% vermiculite, and 25% cattle manure + 25% vermiculite + 25% of cassava foliage + 25% Vida Verde®. Because there was no repetition of the growth environment, the effect of environment was examined using statistical procedures for analysis of combined experiments. Within environments a completely randomized design was used with five replications. All substrates are suitable for the formation of genipap seedlings, where the recommended substrates are: 50% cattle manure + 50% cassava foliage and 50% cattle manure + 50% Vida Verde® for the greenhouse and the substrates composed of 50% cattle manure + 50% vermiculite and 25% cattle manure + 25% cassava foliage + 25% Vida Verde®+ 25% vermiculite for the shaded hut. The buriti shelter is not recommended for production of genipap seedlings.

The impact of carbon source in Candida albicans virulence: participation of RLM1 in pathogen host interaction

Dissertação de mestrado em Genética Molecular

Production of secondary metabolites in cell suspension cultures of Ocimum sanctum L.

Dissertação de mestrado em Plant Molecular Biology, Biotechnology and Bioentrepreneurship

Search for the associated production of the Higgs boson with a top quark pair in multilepton final states with the ATLAS detector

A search for the associated production of the Higgs boson with a top quark pair is performed in multilepton final states using 20.3 fb−1 of proton-proton collision data recorded by the ATLAS experiment at s√=8 TeV at the Large Hadron Collider. Five final states, targeting the decays H→WW∗, ττ, and ZZ∗, are examined for the presence of the Standard Model (SM) Higgs boson: two same-charge light leptons (e or μ) without a hadronically decaying τ lepton; three light leptons; two same-charge light leptons with a hadronically decaying τ lepton; four light leptons; and one light lepton and two hadronically decaying τ leptons. No significant excess of events is observed above the background expectation. The best fit for the tt¯H production cross section, assuming a Higgs boson mass of 125 GeV, is 2.1+1.4−1.2 times the SM expectation, and the observed (expected) upper limit at the 95% confidence level is 4.7 (2.4) times the SM rate. The p-value for compatibility with the background-only hypothesis is 1.8σ; the expectation in the presence of a Standard Model signal is 0.9σ.

ATLAS Run 1 searches for direct pair production of third-generation squarks at the Large Hadron Collider

This paper reviews and extends searches for the direct pair production of the scalar supersymmetric partners of the top and bottom quarks in proton--proton collisions collected by the ATLAS collaboration during the LHC Run 1. Most of the analyses use 20 fb−1 of collisions at a centre-of-mass energy of s√=8 TeV, although in some case an additional 4.7 fb−1 of collision data at s√=7 TeV are used. New analyses are introduced to improve the sensitivity to specific regions of the model parameter space. Since no evidence of third-generation squarks is found, exclusion limits are derived by combining several analyses and are presented in both a simplified model framework, assuming simple decay chains, as well as within the context of more elaborate phenomenological supersymmetric models.

Parameter identification of the fermentative production of fructo-oligosaccharides by Aureobasidium pullulans

In this study, a mathematical model for the production of Fructo-oligosaccharides (FOS) by Aureobasidium pullulans is developed. This model contains a relatively large set of unknown parameters, and the identification problem is analyzed using simulation data, as well as experimental data. Batch experiments were not sufficiently informative to uniquely estimate all the unknown parameters, thus, additional experiments have to be achieved in fed-batch mode to supplement the missing information. © 2015 IEEE.