Bearings and energy storage

Passive magnetic bearings are ideal components for energy storage flywheels which require small dynamic loads and low-maintenance bearings with minimal power requirements. High temperature superconductors such as YBCO can be used to fabricate these bearings and achieve the desired magnetic properties. Stiffness and gap decay due to high speed can be addressed by dynamically altering bearing geometry to provide active control with bulk materials.

Algorithm for identification in the v-gap metric

This paper suggests a method for identification in the v-gap metric. For a finite number of frequency response samples, a problem for identification in the v-gap metric is formulated and an approximate solution is described. It uses an iterative technique for obtaining an L2-gap approximation. Each stage of the iteration involves solving an LMI optimisation. Given a known stabilising controller and the L2-gap approximation, it is shown how to derive a v-gap approximation.

Bonding regimes of nitrogen in amorphous carbon

Nitrogen can have numerous effects on diamond-like carbon: it can dope, it can form the hypothetical superhard compound C3N4, or it can create fullerene-like bonding structures. We studied amorphous carbon nitrogen films deposited by a filtered cathodic vacuum arc as a function of nitrogen content, ion energy and deposition temperature. The incorporation of nitrogen from 10-2 to 10 at% was measured by secondary ion mass spectrometry and elastic recoil detection analysis and was found to vary slightly sublinearly with N2 partial pressure during deposition. In the doping regime from 0 to about 0.4% N, the conductivity changes while the sp3 content and optical gap remain constant. From 0.4 to approximately 10% N, existing sp2 sites condense into clusters and reduce the band gap. Nitrogen contents over 10% change the bonding from mainly sp3 to mainly sp2. Ion energies between 20 and 250 eV do not greatly modify this behaviour. Deposition at higher temperatures causes a sudden loss of sp3 bonding above about 150 °C. Raman spectroscopy and optical gap data show that existing sp2 sites begin to cluster below this temperature, and the clustering continues above this temperature. This transition is found to vary only weakly with nitrogen addition, for N contents below 10%.

Relationship between total length and mouth gap of some commercially important carp fry

The estimated regression equation for total length and mouth gape computed were Log TL = Log 0.23 + 0.663 log MG (vertically) (r = 0.960) and Log TL = Log 0.08 + 0.686 log MG (horizontally) (r = 0.949). In case of rohu average total length from 11350 mm to 23775 mm and mouth gape 805 um to 1225 um (vertically) and 700 um to 1110 um (horizontally) between the first day of mouth opening up to 15 days. The regression equation for total length and mouth gap were Log TL = Log 0.20 + 0.660 log MG (vertically) (r = 0.935) and Log TL = Log 0.02 + 0698 log MG (horizontally) ( r = 0.907). In case of silver carp average total length from 12800 ,urn to 33555 um and mouth gape 690 um to 1210 um (vertically) and 615 um to 1115 um (horizontally) between the first day of mouth opening up to 15 days. The regression equation for total length and mouth gape were Log TL = Log 0.36 + 0.596 log MG (vertically) (r = 0.936) and Log TL = Log 0.26 + 0.607 log MG (horizontally) (r = 0.891). The relationship between total length and mouth gape (vertically and horizontally) of the studied fry were found to be linear and highly significant.

Closing the gap: Improved bounds on optimal POMDP solutions

POMDP algorithms have made significant progress in recent years by allowing practitioners to find good solutions to increasingly large problems. Most approaches (including point-based and policy iteration techniques) operate by refining a lower bound of the optimal value function. Several approaches (e.g., HSVI2, SARSOP, grid-based approaches and online forward search) also refine an upper bound. However, approximating the optimal value function by an upper bound is computationally expensive and therefore tightness is often sacrificed to improve efficiency (e.g., sawtooth approximation). In this paper, we describe a new approach to efficiently compute tighter bounds by i) conducting a prioritized breadth first search over the reachable beliefs, ii) propagating upper bound improvements with an augmented POMDP and iii) using exact linear programming (instead of the sawtooth approximation) for upper bound interpolation. As a result, we can represent the bounds more compactly and significantly reduce the gap between upper and lower bounds on several benchmark problems. Copyright © 2011, Association for the Advancement of Artificial Intelligence. All rights reserved.

Superjunction IGBT filling the gap between SJ MOSFET and ultrafast IGBT

In this letter, we report E off-versus-V ce tradeoff curves for vertical superjunction insulated-gate bipolar transistors (SJ IGBTs), exhibiting unusual inverse slopes dE off/dV ce > 0 in a transition region between purely unipolar and strongly bipolar device behaviors. This effect is due to the action of p-pillar hole current when depleting the drift layer of SJ IGBTs during turnoff and the impact of current gain on the transconductance. Such SJ IGBTs surpass by a very significant margin their superjunction MOSFET counterparts in terms of power-handling capability and on-state and turnoff losses, all at the same time. © 2012 IEEE.