Estudo da incorporação de cinza e chamote gerado pela cerâmica vermelha ao próprio processo industrial

The ceramics industry generates waste at various stages of that process, defective products, waste from burning solid fuels, among others. This waste is dumped in landfills, garbage dumps or directly on roads, which has a negative environmental impact. This paper presents a study to incorporate the waste of algaroba wood and chamote (scrap pieces of ceramic already sintered), in to the ceramic material for making sealing blocks. The methodological procedures consist in the characterization of chemical and mineralogical residues, raw materials, and physical-mechanical of the formulations of mixes with clay, silt and waste. By pressing test pieces were produced using a pressure of 200 kgf/cm², varying compositions in the range of 0%, 5%, 10% and 15% by weight of residue. The sintering was performed in a muffle furnace, with the temperature levels of 850 ° C, 900 ° C, 950 ° C, 1000 ° C and 1050 ° C. The evaluated physical and mechanical properties were: Water Absorption, Linear Shrinkage Burning, Apparent Porosity, Apparent Density and Mechanical Resistance to Flexion. Analysis was carried out by Scanning Electron Microscopy on fracture surfaces of the specimens. Evaluation of linear shrinkage property drying and firing , water absorption and mechanical resistance to compression of the sealing blocks 5% wood ash residue, sintered at 900 °C hold temperature in the laboratory the products manufactured on an industrial scale. The main results, it was found on the viability of using the residues of algaroba wood and to confer refractory properties of the ceramic product. The main results, it was concluded feasibility of using the ash residues algaroba wood to impart refractory properties to the ceramic product and the residue of chamote, being derived from the own ceramic product not interfere with the properties, when used in a percentage of up to 5%.Since the residue of chamote being derived from the ceramic product itself had no effect on the properties. Studies in the laboratory have shown that the incorporation of up to 5% of these residues may be adopted as an alternative technology to reduce the environmental impact caused by the industrial sector, without compromising the final properties of the material, since the results on an industrial scale showed absorption values 11.66 and 11.74 of water and waste products respectively, within the parameters of NBR - 15,270, since the mechanical strength was 1.25 MPa and 0.94 MPa respectively for products with and without residue, lower than the minimum required by the technical standard that is 1.5 MPa.

Estudo da incorporação de cinza e chamote gerado pela cerâmica vermelha ao próprio processo industrial

The ceramics industry generates waste at various stages of that process, defective products, waste from burning solid fuels, among others. This waste is dumped in landfills, garbage dumps or directly on roads, which has a negative environmental impact. This paper presents a study to incorporate the waste of algaroba wood and chamote (scrap pieces of ceramic already sintered), in to the ceramic material for making sealing blocks. The methodological procedures consist in the characterization of chemical and mineralogical residues, raw materials, and physical-mechanical of the formulations of mixes with clay, silt and waste. By pressing test pieces were produced using a pressure of 200 kgf/cm², varying compositions in the range of 0%, 5%, 10% and 15% by weight of residue. The sintering was performed in a muffle furnace, with the temperature levels of 850 ° C, 900 ° C, 950 ° C, 1000 ° C and 1050 ° C. The evaluated physical and mechanical properties were: Water Absorption, Linear Shrinkage Burning, Apparent Porosity, Apparent Density and Mechanical Resistance to Flexion. Analysis was carried out by Scanning Electron Microscopy on fracture surfaces of the specimens. Evaluation of linear shrinkage property drying and firing , water absorption and mechanical resistance to compression of the sealing blocks 5% wood ash residue, sintered at 900 °C hold temperature in the laboratory the products manufactured on an industrial scale. The main results, it was found on the viability of using the residues of algaroba wood and to confer refractory properties of the ceramic product. The main results, it was concluded feasibility of using the ash residues algaroba wood to impart refractory properties to the ceramic product and the residue of chamote, being derived from the own ceramic product not interfere with the properties, when used in a percentage of up to 5%.Since the residue of chamote being derived from the ceramic product itself had no effect on the properties. Studies in the laboratory have shown that the incorporation of up to 5% of these residues may be adopted as an alternative technology to reduce the environmental impact caused by the industrial sector, without compromising the final properties of the material, since the results on an industrial scale showed absorption values 11.66 and 11.74 of water and waste products respectively, within the parameters of NBR - 15,270, since the mechanical strength was 1.25 MPa and 0.94 MPa respectively for products with and without residue, lower than the minimum required by the technical standard that is 1.5 MPa.

Obtenção, caracterização e utilização de um compósito com matriz de resina poliéster e carga de fibras de sisal

The constant search for sustainable alternatives has earned great effort of researchers in research and obtaining new materials, encouraging the rise of eco-friendly productive development and providing simple and practical solutions to economic profitability. In this sense, the use of materials derived from natural renewable sources, vegetables, has great potential applicability to sustainable development. As alternative materials plant fibers can be applied to production of a range of composite materials easing the use of materials derived from non-renewable this thesis were sisal mats used for achieving a composite matrix having as one orthophthalic polyester resin. The webs were subjected to surface treatment in boiling water for 15 minutes. The webs of sisal fibers used were, respectively, 5%, 10% and 15% of the composite weight. The composite was obtained and characterized mechanically and thermally to the chosen formulations. several plates of the composite to obtain the body of evidence for the characterization tests complying with the relevant rules were made. The obtained composites showed strength tensile and bending lower than the array, so it can be used where are required low load requests. The most significant result of the composite studied given to the impact energy absorption, far superior to the matrix used. Other properties were highlighted in oil absorption, and density. It proved the feasibility of obtaining the composite for the three formulations studied C5, C10 and C15 being the most feasible to C10. To demonstrate the feasibility of using composite were made a wall clock, a bench, a chair and a shelf, low mechanical stress structures. It was concluded that the sisal rugs exercised the load function in the composite.

Obtenção, caracterização e utilização de um compósito com matriz de resina poliéster e carga de fibras de sisal

The constant search for sustainable alternatives has earned great effort of researchers in research and obtaining new materials, encouraging the rise of eco-friendly productive development and providing simple and practical solutions to economic profitability. In this sense, the use of materials derived from natural renewable sources, vegetables, has great potential applicability to sustainable development. As alternative materials plant fibers can be applied to production of a range of composite materials easing the use of materials derived from non-renewable this thesis were sisal mats used for achieving a composite matrix having as one orthophthalic polyester resin. The webs were subjected to surface treatment in boiling water for 15 minutes. The webs of sisal fibers used were, respectively, 5%, 10% and 15% of the composite weight. The composite was obtained and characterized mechanically and thermally to the chosen formulations. several plates of the composite to obtain the body of evidence for the characterization tests complying with the relevant rules were made. The obtained composites showed strength tensile and bending lower than the array, so it can be used where are required low load requests. The most significant result of the composite studied given to the impact energy absorption, far superior to the matrix used. Other properties were highlighted in oil absorption, and density. It proved the feasibility of obtaining the composite for the three formulations studied C5, C10 and C15 being the most feasible to C10. To demonstrate the feasibility of using composite were made a wall clock, a bench, a chair and a shelf, low mechanical stress structures. It was concluded that the sisal rugs exercised the load function in the composite.

Obtenção e caracterização de um compósito de matriz polimérica com carga de bucha vegetal luffa cylindrica

Composite materials arise from the need for lighter materials and with bigger mechanical and thermal resistance. The difficulties of discard, recycling or reuse are currently environmental concerns and, therefore, they are study object of much researches. In this perspective the feasibility of using loofahs (Luffa Cylindrica) for obtainment of a polymeric matrix composite was studied. Six formulations, with 4, 5 and 6 treated layers and untreated, were tested. The loofahs were treated in boiling water to remove lignins, waxes and impurities present in the fibers. After that, they were dried in a direct exposure solar dryer. For the characterization of the composite, thermal (thermal conductivity, thermal capacity, thermal diffusivity and thermal resistivity), mechanical (tensile and bending resistance) and physicochemical (SEM, XRD, density, absorption and degradation) properties were determined. The proposed composite has as advantage the low fiber density, which is around 0.66 g/cm³ (almost half of the polyester resin matrix), resulting in an average composite density of around 1.17g/cm³, 6.0 % lower in relation to the matrix. The treatment carried out in the loofahs increased the mechanical strength of the composite and decreased the humidity absorption. The composite showed lower mechanical behavior than the matrix for all the formulations. The composite also demonstrated itself to be feasible for thermal applications, with a value of thermal conductivity of less than 0.159 W/m.K, ranking it as a good thermal insulator. For all formulations/settings a low adherence between fibers and matrix occurred, with the presence of cracks, showing the fragility due to low impregnation of the fiber by the matrix. This composite can be used to manufacture structures that do not require significant mechanical strength, such as solar prototypes, as ovens and stoves.

Obtenção e caracterização de um compósito de matriz polimérica com carga de bucha vegetal luffa cylindrica

Composite materials arise from the need for lighter materials and with bigger mechanical and thermal resistance. The difficulties of discard, recycling or reuse are currently environmental concerns and, therefore, they are study object of much researches. In this perspective the feasibility of using loofahs (Luffa Cylindrica) for obtainment of a polymeric matrix composite was studied. Six formulations, with 4, 5 and 6 treated layers and untreated, were tested. The loofahs were treated in boiling water to remove lignins, waxes and impurities present in the fibers. After that, they were dried in a direct exposure solar dryer. For the characterization of the composite, thermal (thermal conductivity, thermal capacity, thermal diffusivity and thermal resistivity), mechanical (tensile and bending resistance) and physicochemical (SEM, XRD, density, absorption and degradation) properties were determined. The proposed composite has as advantage the low fiber density, which is around 0.66 g/cm³ (almost half of the polyester resin matrix), resulting in an average composite density of around 1.17g/cm³, 6.0 % lower in relation to the matrix. The treatment carried out in the loofahs increased the mechanical strength of the composite and decreased the humidity absorption. The composite showed lower mechanical behavior than the matrix for all the formulations. The composite also demonstrated itself to be feasible for thermal applications, with a value of thermal conductivity of less than 0.159 W/m.K, ranking it as a good thermal insulator. For all formulations/settings a low adherence between fibers and matrix occurred, with the presence of cracks, showing the fragility due to low impregnation of the fiber by the matrix. This composite can be used to manufacture structures that do not require significant mechanical strength, such as solar prototypes, as ovens and stoves.

Formulação de pasta de cimento flexível utilizando planejamento experimental

Steam injection is an oil recovery method accomplished by introducing steam directly into the oil well to the reservoir. The steam causes dilation of the casing, which, after reduction in temperature, tends to return to the initial dimensions: causing the formation of cracks in the cement and loss of hydraulic isolation.. In this context, the type of the SBR latex is used to improve the flexibility of the cement matrix by reducing the amount of fatigue failure. To prevent these failures, the mechanical resistance parameters should be carefully adjusted to well conditions. This work aims to study the mechanical behavior of cement slurry systems additivated with SBR latex for cementing oil wells subject to steam injection. Through the central composite factorial design was studied the behavior of the compressive strength by varying the density of the paste between 1.75 g /cm³ (14.6 lb/ Gal) and 1.89 g/cm³ (15,8lb / Gal), curing time between 4 days and 28 days and concentration of SBR Latex between 0 L / m³ and 534.722 L / m³ (0 gpc and 4 gpc). The results showed that increasing the concentration of SBR latex, within the given ranges, there was a decreased compression resistance and elastic modulus by increasing the elastic deformability of the slurry. From the results it can determine best slurries formulation conditions in oil well cementing operations subject to steam injection.

Formulação de pasta de cimento flexível utilizando planejamento experimental

Steam injection is an oil recovery method accomplished by introducing steam directly into the oil well to the reservoir. The steam causes dilation of the casing, which, after reduction in temperature, tends to return to the initial dimensions: causing the formation of cracks in the cement and loss of hydraulic isolation.. In this context, the type of the SBR latex is used to improve the flexibility of the cement matrix by reducing the amount of fatigue failure. To prevent these failures, the mechanical resistance parameters should be carefully adjusted to well conditions. This work aims to study the mechanical behavior of cement slurry systems additivated with SBR latex for cementing oil wells subject to steam injection. Through the central composite factorial design was studied the behavior of the compressive strength by varying the density of the paste between 1.75 g /cm³ (14.6 lb/ Gal) and 1.89 g/cm³ (15,8lb / Gal), curing time between 4 days and 28 days and concentration of SBR Latex between 0 L / m³ and 534.722 L / m³ (0 gpc and 4 gpc). The results showed that increasing the concentration of SBR latex, within the given ranges, there was a decreased compression resistance and elastic modulus by increasing the elastic deformability of the slurry. From the results it can determine best slurries formulation conditions in oil well cementing operations subject to steam injection.

Influência da utilização do fluido de corte com adição de grafeno na temperatura de usinagem e formação de rebarba no processo de micro fresamento

As time passed, humanity needed the development of new materials used in various activities. High strength materials such as titanium and Inconel for example, had been studied because they are widely used for implants in biomedicine, as well as their use in aerospace and automotive industries. Because of its thermal and mechanical properties, these materials are considered difficult to machine, promoting a rapid wear of cutting tools, primarily caused by the high temperatures in machining. With the development of new materials has emerged the need of developing new manufacturing processes. One of today’s innovative processes is the micro-manufacturing. Being a process with a defined cutting tool geometry, burr formation is a constant and undesirable phenomenon formed during the machininig process. Being detrimental to the manufacturing process, overspending deburring operations are constantly employed leading to increase the aggregate cost to the manufactured material. Assembly components are also impaired if there is no control of the burr, with consequences including the disposal of components due to the occurence of this phenomenon. This paper presents the study of micro-milling Inconel 718, investigating influential parameters in the formation of burrs in order to minimize the occurrence of this phenome non. Different feed rates per tooth and cutting speed are evaluated, and different cutting fluids with different methods of applying the fluid. Adding graphene to cutting fluids was considered as a variable to be investigated, which is considered an excellent solid lubricant, in addition to increasing the thermal conductivity of the cooling solution (AZIMI; MOZAF FARI, 2015). The micro-milling temperature was evaluated in the present work. It was observed a new phenomenon that causes the machined surface temperature decreases below room temperature when using the solution water + oil. This phenomenon is explained in further chapters. In order to unravel this phenomenon, a new test was proposed and, from this test, it can be concluded, comparatively, which cutting fluid has a better cooling property.Using cutting fluid with different thermal properties has shown influence when analy zing burr formation and reducing machining temperature.

Obtenção de triacetato de celulose a partir do bagaço de cana-deaçúcar para revestimento de micropartículas de goma gelana e avaliação do seu perfil de liberação in vitro e da mucoadesão ex vivo

Oral route of administration is considered to be the most comfortable, safe and greater adaptation for patients. But, oral route presents some disadvantages such as drugs bioavailability and side effects on the stomach. Some technologies are studied to soften and/or resolve these problems, such as coating with polymeric films, which are able to protect the pharmaceutical form of the acid stomachic environment and to act in the drug release, and mucoadhesive systems, which allow the pharmaceutical form remains a greater time interval in the intestine, increasing the effectiveness of the drug. Cellulose triacetate (CTA) films were produced from cellulose extracted from sugar cane bagasse. The films were prepared with different morphologies (with and without water, acting as non-solvent) and concentrations (3, 6.5 and 10%) of CTA and characterized using scanning electron microscopy (SEM), water vapor permeability (WVP), puncture resistance (PR), enzymatic digestion (DE), and mucoadhesive force evaluation (MF). Microscopy showed the formation of symmetric and asymmetric morphologies. WVP data showed that more concentrated films have higher values for WVP; moreover, asymmetric films had higher values than symmetric films. PR measurements showed that symmetric membranes are more resistant than asymmetric ones. More concentrated films were also more puncture resistant, except for symmetric membranes with CTA concentrations of 6.5 and 10% that did not show significant differences. All of the films presented large mucoadhesive capacities independent of their morphology and CTA concentration. From the results of WVP and RP, a symmetric filme with 6.5% CTA showed better ability and mechanical resistance, therefore, was selected to serve as coating of gellan gum (GG) particles incorporating ketoprofen (KET), which was confirmed by SEM. The selected film presented low values in measurements of the swelling index (SI) and in a dissolution test (DT). TGA analysis showed that the CTA coating does not influence the thermal stability of the particles and there is no incompatibility evidence between CTA, GG and KET. Coated particles released 100% of the ketoprofen in 24 h, while uncoated particles released the same amount in 4 h. The results of this study highlight the potential of CTA in the development of new controlled oral delivery systems.

Comportamento mecânico e biológico de implante dentário com interface cônica interna

The general aim of this study was to evaluate the conical interface of pilar/implant. The specific aims were to evaluate the influence of hexagonal internal index in the microleakage and mechanical strength of Morse taper implants; the effect of axial loading on the deformation in cervical region of Morse taper implants of different diameters through strain gauge; the effect of axial loading in cervical deformation and sliding of abutment into the implant by tridimensional measurements; the integrity of conical interface before and after dynamic loading by microscopy and microleakage; and the stress distribution in tridimensional finite element models of Morse taper implants assembled with 2 pieces abutment. According to the obtained results, could be concluded that the diameter had influence in the cervical deformation of Morse taper implants; the presence of internal hexagonal index in the end of internal cone of implant didn´t influenced the bacterial microleakage under static loading neither reduced the mechanical strength of implants; one million cycles of vertical and off-center load had no negative influence in Morse taper implant integrity.

Componentes poliméricos de alto desempenho para a indústria automóvel

Atualmente, a utilização e as diversas aplicações de materiais poliméricos seguem tendências crescentes, pelo que se torna necessário aprofundar a compreensão do seu comportamento e funcionalidades. Neste contexto, na presente dissertação analisa-se a fabricação e características de rolamentos poliméricos para a suspensão automóvel. Estes rolamentos visam a substituição dos clássicos rolamentos metálicos. Esta substituição tem por objetivos garantir a melhoria do funcionamento dos rolamentos, bem como o seu usufruto, contribuindo para um maior conforto e segurança dos passageiros e para uma redução do peso do veículo, com consequente diminuição do consumo do combustível e melhoria da eficiência. Sendo o poliacetal (POM) e a poliamida (PA) considerados polímeros de alto desempenho, estes polímeros reúnem boas características para aplicação na fabricação de dispositivos com funcionalidades exigentes como é o caso dos rolamentos. O presente trabalho aborda o estudo de algumas das suas propriedades, de modo a obter informações relevantes quanto à respetiva aplicação em rolamentos de suspensão, tendo como foco principal a análise da matéria-prima utilizada. Deste modo, alteraram-se as formulações variando-se os teores de material virgem e reciclado, estudou-se o ser comportamento mecânico, reológico e térmico: fizeram-se análises reológicas através do estudo do MFI a fim de se obterem informações complementares ao estudo mecânico, realizaram-se análises térmicas para avaliar a possibilidade de degradação térmica do material e, no caso da PA66-30GF, recorreu-se à microscopia eletrónica de varrimento para se estudar os aspetos microestruturais deste compósito reforçado com fibra de vidro. Adicionalmente, procedeu-se à análise da rugosidade superficial dos componentes dos rolamentos e quantificou-se o torque dos mesmos. A partir dos estudos anteriores, foi possível concluir que o POM apresenta um comportamento mecânico estável mesmo utilizando uma formulação com 100% de material reciclado. Este comportamento não se verificou na PA6630GF, dado que as suas propriedades mecânicas são afetadas de forma significativa pelo teor de reciclado na formulação. Com o estudo do torque determinou-se o valor limite do momento de torsão do rolamento que garante o seu bom funcionamento e eficácia.

Comportamento e reforço de nós viga-pilar

A presente dissertação tem como principal objetivo a análise do comportamento do nó viga-pilar, com a finalidade de dimensionar uma solução de reforço sísmico a aplicar em nós de estruturas antigas de betão armado. Uma parte considerável das construções em betão armado construídas em Portugal até 1970 são muito frágeis relativamente às ações sísmicas. Devido a este fato, os edifícios estão associados a uma conceção desajustada face à regulamentação atual pois à época não estava prevista a consideração de ações sísmicas na execução dos projetos de estruturas. Nesse período, era prática comum na construção o uso de armadura lisa conjugada com uma má pormenorização das armaduras e baixa resistência mecânica do betão. Tal levava a que as estruturas de betão armado construídas em Portugal até à década de setenta, possuírem uma baixa capacidade para resistir a solicitações cíclicas, como as induzidas pelos sismos. Os nós viga-pilar das estruturaras de betão armado são considerados as zonas mais crítica e vulnerável a ações sísmicas. Por isso é frequente em estruturas antigas, a necessidade de as reforçar, para melhorar a performance do edifício durante os sismos. Têm sido estudadas por investigadores várias técnicas e soluções para reforçar os nós viga-pilar de estruturas antigas de betão armado. Serão analisados nesta dissertação os danos observados em dois nós viga-pilar ensaiados experimentalmente, onde são simuladas as ações cíclicas horizontais dos sismos. Com base nestes dados, é proposta e detalhada uma solução de reforço para melhorar o comportamento histerético dessa ligações, de forma a conferir uma maior capacidade resistente e/ou ductilidade.

Sensibilidade à mudança de trajetória de deformação no aço TWIP980

Resultante dos avanços tecnológicos, conseguiu-se obter um aço que elimina o paradigma de se aliar alta ductilidade e resistência mecânica. Assim foi desenvolvido durante a última década o aço TWIP, deformação induzida por maclação, tendo como principal mecanismo de deformação a maclação. Este presente trabalho teve como principal objetivo caraterizar o aço TWIP980 em três temáticas diferentes: química, mecânica e microestrutura. Na primeira temática, a química, esta teve como objetivo encontrar a designação do aço TWIP em estudo. Sendo apenas conhecida a direção de laminação, RD, e a empresa que forneceu as chapas, a POSCO, o objetivo era obter a sua designação. Através da comparação das curvas de tração encontradas para o material em estudo, e conjuntamente, com as diversas curvas de tração de vários aços TWIP da empresa POSCO, realizou-se a comparação. Visto ter-se ficado reduzido a dois possíveis aços TWIP, foi através de uma análise à composição química, EDS - Espectroscopia da energia dispersa por raios-X, que se concluiu que o aço em estudo era o TWIP980. Na caraterização mecânica, e através de ensaios de tração, foram estudadas propriedades como: o módulo de elasticidade, tensão limite elástico, ductilidade, anisotropia, coeficiente de encruamento e Poisson. Estas propriedades foram estudas para três mudanças na trajetória de deformação e quatro pré-deformações em estudo. Assim estudou-se a alteração de trajetória para os ângulos a 0º, 45º e 90º em relação a RD, para as deformações de engenharia de 0%, 10%, 20% e 30%. Por último, na análise à microestrutura, esta teve como objetivo obter valores para o tamanho de grão e de macla bem como as suas orientações cristalográficas. Também a densidade de deslocações e maclação para cada uma das 4 pré-deformações esteve em estudo. Estes parâmetros foram obtidos através de microscopia ótica, eletrónica de varrimento, MEV e eletrónica de transmissão, MET.

Cimentos injetáveis à base de fosfatos de cálcio para vertebroplastia

O principal objectivo desta investigação foi o desenvolvimento cimentos de fosfatos de cálcio com injetabilidade melhorada e propriedades mecânicas adequadas para aplicação em vertebroplastia. Os pós de fosfato de tricálcico (TCP) não dopados e dopados (Mg, Sr e Mn) usados neste estudo foram obtidos pelo processo de precipitação em meio aquoso, seguidos de tratamento térmico de forma a obter as fases pretendidas, α− e β−TCP. A substituição parcial de iões Ca por iões dopantes mostrou ter implicações em termos de estabilidade térmica da fase β−TCP. Os resultados demonstraram que as transformações de fase alotrópicas β↔α−TCP são fortemente influenciadas por variáveis experimentais como a taxa de arrefecimento, a presença de impurezas de pirofosfato de cálcio e a extensão do grau de dopagem com Mg. Os cimentos foram preparados através da mistura de pós, β−TCP (não dopados e dopados) e fosfato monocálcico monidratado (MCPM), com meios líquidos diferentes usando ácido cítrico e açucares (sucrose e frutose) como agentes retardadores de presa, e o polietilenoglicol, a hidroxipropilmetilcelulose e a polivinilpirrolidona como agentes gelificantes. Estes aditivos, principalmente o ácido cítrico, e o MCPM aumentam significativamente a força iónica do meio, influenciando a injetabilidade das pastas. Os resultados também mostraram que a distribuição de tamanho de partícula dos pós é um factor determinante na injetabilidade das pastas cimentícias. A combinação da co-dopagem de Mn e Sr com a adição de sucrose no líquido de presa e com uma distribuição de tamanho de partícula dos pós adequada resultou em cimentos de brushite com propriedades bastante melhoradas em termos de manuseamento, microestrutura, comportamento mecânico e biológico: (i) o tempo inicial de presa passou de ~3 min to ~9 min; (ii) as pastas cimentícias foram totalmente injectadas para uma razão liquido/pó de 0.28 mL g−1 com ausência do efeito de “filter-pressing” (separação de fases líquida e sólida); (iii) após imersão numa solução durante 48 h, as amostras de cimento molhadas apresentam uma porosidade total de ~32% e uma resistência a compressão de ~17 MPa, valor muito superior ao obtido para os cimentos sem açúcar não dopados (5 MPa) ou dopados só com Sr (10 MPa); e (iv) o desempenho biológico, incluindo a adesão e crescimento de células osteoblásticas na superfície do cimento, foi muito melhorado. Este conjunto de propriedades torna os cimentos excelentes para regeneração óssea e engenharia de tecidos, e muito promissores para aplicação em vertebroplastia.