Inverse Metabolic Engineering of Synechocystis PCC 6803 for Improved Growth Rate and Poly-3-hydroxybutyrate Production

Synechocystis PCC 6803 is a photosynthetic bacterium that has the potential to make bioproducts from carbon dioxide and light. Biochemical production from photosynthetic organisms is attractive because it replaces the typical bioprocessing steps of crop growth, milling, and fermentation, with a one-step photosynthetic process. However, low yields and slow growth rates limit the economic potential of such endeavors. Rational metabolic engineering methods are hindered by limited cellular knowledge and inadequate models of Synechocystis. Instead, inverse metabolic engineering, a scheme based on combinatorial gene searches which does not require detailed cellular models, but can exploit sequence data and existing molecular biological techniques, was used to find genes that (1) improve the production of the biopolymer poly-3-hydroxybutyrate (PHB) and (2) increase the growth rate. A fluorescence activated cell sorting assay was developed to screen for high PHB producing clones. Separately, serial sub-culturing was used to select clones that improve growth rate. Novel gene knock-outs were identified that increase PHB production and others that increase the specific growth rate. These improvements make this system more attractive for industrial use and demonstrate the power of inverse metabolic engineering to identify novel phenotype-associated genes in poorly understood systems.

The Influence of Adjacent Segment on the Reliability of Cu Dual Damascene Interconnects

Three terminal ‘dotted-I’ interconnect structures, with vias at both ends and an additional via in the middle, were tested under various test conditions. Mortalities (failures) were found in right segments with jL value as low as 1250 A/cm, and the mortality of a dotted-I segment is dependent on the direction and magnitude of the current in the adjacent segment. Some mortalities were also found in the right segments under a test condition where no failure was expected. Cu extrusion along the delaminated Cu/Si₃N₄ interface near the central via region was believed to cause the unexpected failures. From the time-to-failure (TTF), it is possible to quantify the Cu/Si₃N₄ interfacial strength and bonding energy. Hence, the demonstrated test methodology can be used to investigate the integrity of the Cu dual damascene processes. As conventionally determined critical jL values in two-terminal via-terminated lines cannot be directly applied to interconnects with branched segments, this also serves as a good methodology to identify the critical effective jL values for immortality.

Flexure based mounts for sensitive payloads : a management and engineering study

by Daniel K. Moon.

Effects of the heterogeneity of the variances on reliability generalization : An example with the beck depression inventory

Resumen tomado de la publicaci??n

Experience in introduction of English terminology in engineering lessons: methodology and evaluation

This communication explains a experience for the introduction of English terminology in a technical degree of higher education. We present the methodology and assessment procedures used to evaluate the way the students perceived the introduction of terminology in English in two different subjects from 3rd and 5th year courses of a Computer Science degree in which English was not the vehicular language. We propose a strategy based on two main pillars, namely: 1) The design of materials, explanations, and exams, paying particular attention to the way in which the specific terminology was exposed to the students, and 2) The assessment of the impact in the students by means of the analysis of the feedback trough a set of enquiries. Our experience showed that the students responded very positively to the introduction of English terminology, and presented an affirmative feedback about the impact that an improvement of their linguistic abilities would have in their future work. Further, we present statistics regarding the use of English as the vehicular language for technical reports, which is envisaged as very useful by the students. Finally, we propose a set of questions for further debate which are centered in the role that English terminology should pay in technical degrees, and about the way in which universities should deploy resources in English languages within the different Syllabus

Engineering Foundation Year - Sustaining Success - Lecture 1 - slides

These materials are used in student tutorials as part of the routes to success course. The tutorials are typically delivered to a large group (~50) in an interactive manner, with the slides serving as reference/check materials. Some of the questions in the slides can also be used as individual handouts

The Higher Education Academy Engineering Subject Center

The engineering subject center provides support for engineering students and staff in higher education at university. The website provides articles helping students in a large range of subjects, such as book reviews for a variety subjects, support in writing reports or essays and personal development in subject areas and university life in general.

Engineering 1A

Exam questions and solutions for a first year engineering maths exam. Short questions (section A) and longer questions (section B). Diagrams for the question are all together in the support.zip file, as .eps files

Engineering 1B

Exercises and solutions for a first year course. Diagrams for the questions are all together in the support.zip file, as .eps files

Software Engineering Models

This presentation gives a high level introduction to modelling in software engineering. It looks in detail at how to model behaviour, in particular using UML Activity Diagrams.

Engineering Foundation Year - Sustaining Success Portfolio Template

Template - word processed document for 'Routes to Success' Coursework 3 'Sustaining Success'

Engineering Foundation Year - Sustaining Success Week 1

Slides for first week of teaching

Engineering Foundation Year - Sustaining Success Week 1

Slides for first week of teaching, PDF 6 up