Poly methacrylate-plasticiser-salt blends as solid polymer electrolytes

Methoxy-ethylene glycol methacrylates, CH₂=CMeCOO(CH₂CH₂O)_nMe (n = 1, 2, 3), ethoxy-triethylene glycol methacrylate, CH₂=CMeCOO(CH₂CH₂O)₃Et, and N,N-dimethylaminoethyl methacrylate, CH₂=CMeCOOCH₂CH₂NMe₂, were used to synthesise the corresponding polymers. Conductivities of these polymers complexed with lithium perchlorate were investigated. Tetraethylene glycol dimethyl ether was used as plasticiser to increase the conductivity of the materials. A conductivity of 10⁻⁵ S cm⁻¹ was obtained at room temperature for the plasticised polymer samples. Effects of polymer structure, plasticiser, salt concentration and temperature on conductivity and glass transition temperature of the polymer electrolytes are discussed.

Mechanical properties of polyether-plasticiser-salt systems as polymer electrolytes

The mechanical properties of urethane crosslinked poly(ethylene oxide-co-propylene oxide) glyceryl ether-plasticiser (tetraethylene glycol dimethyl ether, or methylformamide)-salt (LiClO₄)-based polymer electrolytes have been studied. It was found that, with increasing concentration of salt, the elastic modulus and tensile strength of the materials unexpectedly decrease. This is interpreted in terms of a predominance of intramolecular coordination of the Li⁺ ions by the polymer.

N,N-Dimethylpyrrolidinium hydroxide : a highly conductive solid material at ambient temperature

N,N-Dimethylpyrrolidinium hydroxide (P₁₁OH·4H₂O) was found to exhibit high ionic conductivity in the solid state (7 × 10⁻³ S cm⁻¹ at 25°C) and unusual thermal properties, and ²H solid state NMR measurements indicate liquid-like mobility of the deuterium species in the solid state of P₁₁OD·4.5D₂O.

Conductive plastic crystal phases of the 1-alkyl-2-methyl pyrrolinium TFSA salts

Characterization of a new family of salts, based on a number of 1-alkyl-2-methyl pyrrolinium cations and the bis(trifluoromethane sulfonyl) amide anion (TFSA), is presented. From the thermal analysis, conductivity and X-ray diffraction (XRD) measurements, at least one of the compounds of the family, 1-ethyl-2-methyl pyrrolinium TFSA, was found to exhibit plastic crystal phases before melting and to exhibit high conductivity in the solid state (1×10⁻⁴ S cm⁻¹ at 25 °C). This plastic crystal behaviour is discussed in comparison with other members of this pyrrolinium salt family.

Polymer-in-ionic-liquid electrolytes

In order to achieve high conductivity in a polymer electrolyte, polymer-in-ionic-liquid electrolytes have been explored. It is found in this study that poly[vinylpyrrolidone-co-(vinyl acetate)] (P(VP-c-VA)) in 1-ethyl-3-methylimidazolium bis(trifluoromethyl sulfonyl) amide (EtMeIm+Tf2N−) and poly(N,N-dimethyl acrylamide) (PDMAA) in trimethyl butyl ammonium bis(trifluoromethane sulfonyl) amide (N1114+Tf2N−) produce ion-conducting liquids and gels. The P(VP-c-VA)/ EtMeIm+Tf2N− mixture has a conductivity around 10−3 S · cm−1 at 22 °C, for copolymer concentrations up to 30 wt.-%. Thermal analysis shows that the Tg of the P(VP-c-VA)/ EtMeIm+Tf2N− system is well described by the Fox equation as a function of polymer content. Poly(methyl methacrylate) (PMMA)/ EtMeIm+Tf2N− gel electrolytes were prepared by in-situ polymerisation of the monomer in the ionic liquid. In the presence of 0.5–2.0 wt.-% of a crosslinking agent, these PMMA-based electrolytes displayed elastomeric properties and high conductivity (ca. 10−3 S · cm−1) at room temperature.

Polyelectrolyte-in-ionic-liquid electrolytes

Novel polymer electrolyte materials based on a polyelectrolyte-in-ionic-liquid principle are described. A combination of a lithium 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPSLi) and N,N′-dimethylacrylamide (DMMA) are miscible with the ionic liquid, 1-ethyl-3-methylimidazolium dicyanamide (EMIDCA). EMIDCA has remarkably high conductivity (≥ 2 · 10−2 S · cm−1) at room temperature and acts as a good solvating medium for the polyelectrolyte. At compositions of AMPSLi less than or equal to 75 mol-% in the copolymer (P(AMPSLi-co-DMAA)), the polyelectrolytes in EMIDCA are homogeneous, flexible elastomeric gel materials at 10 − 15 wt.-% of total polyelectrolyte. Conductivities higher than 8 · 10−3 S · cm−1 at 30 °C have been achieved. The effects of the monomer composition, polyelectrolyte concentration, temperature and lithium concentration on the ionic conductivity have been studied using thermal and conductivity analysis, and pulsed field gradient nuclear magnetic resonance techniques.

Control of magnesium interfacial reactions in aqueous electrolytes towards a biocompatible battery

A stable magnesium battery has been developed based on a magnesium anode, a poly(dioxyethane thiophene) (PEDOT) cathode and a near-saturated aqueous solution of LiCl, MgCl₂, or mixture of these salts at pH of 11. This combination leads to a low water activity in the electrolyte, which thus suppresses the hydrogen evolution reaction on Mg, as well as producing a stable oxy-hydroxide film which protects the metal surface from freely corroding. The conducting polymer cathode is reduced somewhat during the discharge process, however, appears to be readily re-oxidised (as determined from the resistance) by the oxygen present in the cell. The cell is therefore primarily a Mg/O₂ battery, however, the PEDOT appears to enhance the performance, in particular the discharge voltage.

A new class of proton-conducting ionic plastic crystals based on organic cations and dihydrogen phosphate

Choline dihydrogen phosphate ([N_1.1.1.2OH]DHP) and 1-butyl-3-methylimidazolium dihydrogen phosphate ([C₄mim]DHP) were synthesized as a new class of proton-conducting ionic plastic crystals. Both [N_1.1.1.2OH]DHP and [C₄mim]DHP showed solid–solid phase transition(s) and showed a final entropy of fusion lower than 20 J K⁻¹ mol⁻¹ which is consistent with Timmerman’s criterion for molecular plastic crystals. The ionic conductivity of [N_1.1.1.2OH]DHP was in the range of 10⁻⁶ S cm⁻¹–10⁻³ S cm⁻¹ in the plastic crystalline phase. On the other hand, the ionic conductivity of [C₄mim]DHP showed about 10⁻⁵ S cm⁻¹ in the plastic crystalline phase. [N_1.1.1.2OH]DHP showed one order of magnitude higher ionic conductivity than [C₄mim]DHP in the temperature range where the plastic phase is stable.

Solid state actuators based on polypyrrole and polymer-in-ionic liquid electrolytes

Novel polymer-in-ionic liquid electrolytes (PILEs) have been developed for solid state electrochemical actuators based on polypyrrole. The active polymer electrodes are readily oxidized/reduced without degradation in the PILE. It was found that the actuator cycle life is significantly enhanced in the PILE as is the ‘shelf life’ of the device.

Investigation of proton dynamics and the proton transport pathway in choline dihydrogen phosphate using solid-state NMR

Choline dihydrogen phosphate has previously been shown to be a good ionic conductor as well as an excellent host for acid doping, leading to high proton conductivities required for e.g., electrochemical devices including proton membrane fuel cells and sensors. A combination of variable-temperature ¹H solid-state NMR and 2D NMR pulse sequences, including ³¹P and ¹³C CODEX and ¹H BaBa, show that the proton conduction mechanism primarily involves assisted transport via a restricted three-site motion of the phosphate unit around the P–O bond that is hydrogen bonded to the choline and exchange of protons between these anions. In other words, proton transport at ambient temperatures appears to occur most favorably along the crystallographic b axis, from phosphate dimer to dimer. At elevated temperatures exchange between the protons of the hydroxyl group on the choline cation and the hydrogen-bonded dihydrogen phosphate groups also contributes to the structural diffusion of the protons in this solid state conductor.

On the role of cyclic unsaturated additives on the behaviour of lithium metal electrodes in ionic liquid electrolytes

Three cyclic vinyl based additives, based respectively on oxygen, sulphur and fluorine, are tested for their ability to improve the cycling of lithium in a hostile ionic liquid medium. Oxygen based vinylene carbonate is found to offer the best protection of the lithium metal whilst allowing very consistent lithium cycling to occur. The vinylene carbonate based system under study is, however, imperfect. Lithium metal is deposited in a dendritic morphology, and vinylene carbonate is rapidly consumed during lithium cycling if it is present in a small quantity. Our results suggest that ionic liquid systems critically relying on a small amount of additive to protect a lithium electrode are not viable for long cycle life secondary batteries. It is suggested that an ionic liquid which itself is lithium metal compatible be used instead.

Organic ionic plastic crystals : recent advances

Investigations into the synthesis and utilisation of organic ionic plastic crystals have made significant progress in recent years, driven by a continued need for high conductivity solid state electrolytes for a range of electrochemical devices. There are a number of different aspects to research in this area; fundamental studies, utilising a wide range of analytical techniques, of both pure and doped plastic crystals, and the development of plastic crystal-based materials as electrolytes in, for example, lithium ion batteries. Progress in these areas is highlighted and the development of new organic ionic plastic crystals, including a new class of proton conductors, is discussed.

Proton transport in choline dihydrogen phosphate/H3PO4 mixtures

Mixtures of the plastic crystal material choline dihydrogen phosphate [Choline][DHP] and phosphoric acid, from 4.5 mol% to 18 mol% H₃PO₄, were investigated and shown to have significantly higher proton conductivity compared to the pure [Choline][DHP]. This was particularly evident from the electrochemical hydrogen reduction reaction and the proton NMR diffusion measurements, in addition to ionic conductivity measured from the impedance spectroscopy. The ionic conductivity was observed to increase by more than an order of magnitude in phase I (i.e. the highest temperature solid phase in [Choline][DHP]) reaching up to 10⁻² S cm⁻¹. The multinuclear NMR spectroscopy data suggest that, at least on the timescale of the NMR measurement, the H⁺ cations and [DHP] anions are equivalent in both phases. The pulsed field gradient NMR diffusion measurements of the 18 mol% acid sample indicate that all three ions are mobile, however the H⁺ diffusion coefficient is an order of magnitude higher than for the [Choline] cation or the [DHP] anion, and therefore conduction in these materials is dominated by proton conductivity. The thermal stability, as measured by TGA, is unaffected with increasing acid additions and remains high; i.e. no significant mass loss below 200 °C.