Determining aflatoxins B1, B2, G1 and G2 in maize using florisil clean up with thin layer chromatography and visual and densitometric quantification

A method for determining aflatoxins B1 (AFB1), B2 (AFB2),G1 (AFG1) andG2 (AFG2) in maize with florisil clean up was optimised aiming at one-dimensional thin layer chromatography (TLC) analysis with visual and densitometric quantification. Aflatoxins were extracted with chloroform: water (30:1, v/v), purified through florisil cartridges, separated on TLC plate, detected and quantified by visual and densitometric analysis. The in-house method performance characteristics were determined by using spiked, naturally contaminated maize samples, and certified reference material. The mean recoveries for aflatoxins were 94.2, 81.9, 93.5 and 97.3% in the range of 1.0 to 242 µg/kg for AFB1, 0.3 to 85mg/kg for AFB2, 0.6 to 148mg/kg for AFG1 and 0.6 to 140mg/kg for AFG2, respectively. The correlation values between visual and densitometric analysis for spiked samples were higher than 0.99 for AFB1, AFB2, AFG1 and 0.98 for AFG2. The mean relative standard deviations (RSD) for spiked samples were 16.2, 20.6, 12.8 and 16.9% for AFB1, AFB2, AFG1 and AFG2, respectively. The RSD of the method for naturally contaminated sample (n = 5) was 16.8% for AFB1 and 27.2% for AFB2. The limits of detection of the method (LD) were 0.2, 0.1, 0.1 and 0.1mg/kg and the limits of quantification (LQ) were 1.0, 0.3, 0.6 and 0.6mg/kg for AFB1, AFB2, AFG1 and AFG2, respectively.

Ochratoxin A determination in beer by immunoaffinity column clean-up and high-performance liquid chromatography

Analyses of ochratoxin A (OTA) in domestic and imported beers were perfomed by immunoaffinity column and high - perfomance liquid chromatography (HPLC) using a fluorescence detector. Recoveries of OTA from beer samples spiked at levels from 8.0 to 800pg/mL ranged from 81.2% to 95.0%, with coefficient of variation between 0% e 11.0%. Detection limit and quantification limit were 2.0pg/mL and 8.0pg/mL, respectively. Of the total of 26 samples produced in Brazil only 6 (23%), contained trace amounts of OTA. Of the 4 imported beers, in 2, Ireland and Germany, were detected OTA at levels of 25pg/mL and 82pg/mL, respectively.

Structural dynamics in the global pulp and paper industry

The pulp and paper industry is currently facing broad structural changes due to global shifts in demand and supply. These changes have significant impacts on national economies worldwide. Planted forests (especially eucalyptus) and recovered paper have quickly increased their importance as raw material for paper and paperboard production. Although advances in information and communication technologies could reduce the demand for communication papers, and the growth of paper consumption has indeed flattened in developed economies, particularly in North America and Western Europe, the consumption is increasing on a global scale. Moreover, the focal point of production and consumption is moving from the Western world to the rapidly growing markets of Southeast Asia. This study analyzes how the so-called megatrends (globalization, technological development, and increasing environmental awareness) affect the pulp and paper industry’s external environment, and seeks reliable ways to incorporate the impact of the megatrends on the models concerning the demand, trade, and use of paper and pulp. The study expands current research in several directions and points of view, for example, by applying and incorporating several quantitative methods and different models. As a result, the thesis makes a significant contribution to better understand and measure the impacts of structural changes on the pulp and paper industry. It also provides some managerial and policy implications.

Feasibility of industrial implementation of laser cutting into paper making machine

Laser cutting implementation possibilities into paper making machine was studied as the main objective of the work. Laser cutting technology application was considered as a replacement tool for conventional cutting methods used in paper making machines for longitudinal cutting such as edge trimming at different paper making process and tambour roll slitting. Laser cutting of paper was tested in 70’s for the first time. Since then, laser cutting and processing has been applied for paper materials with different level of success in industry. Laser cutting can be employed for longitudinal cutting of paper web in machine direction. The most common conventional cutting methods include water jet cutting and rotating slitting blades applied in paper making machines. Cutting with CO2 laser fulfils basic requirements for cutting quality, applicability to material and cutting speeds in all locations where longitudinal cutting is needed. Literature review provided description of advantages, disadvantages and challenges of laser technology when it was applied for cutting of paper material with particular attention to cutting of moving paper web. Based on studied laser cutting capabilities and problem definition of conventional cutting technologies, preliminary selection of the most promising application area was carried out. Laser cutting (trimming) of paper web edges in wet end was estimated to be the most promising area where it can be implemented. This assumption was made on the basis of rate of web breaks occurrence. It was found that up to 64 % of total number of web breaks occurred in wet end, particularly in location of so called open draws where paper web was transferred unsupported by wire or felt. Distribution of web breaks in machine cross direction revealed that defects of paper web edge was the main reason of tearing initiation and consequent web break. The assumption was made that laser cutting was capable of improvement of laser cut edge tensile strength due to high cutting quality and sealing effect of the edge after laser cutting. Studies of laser ablation of cellulose supported this claim. Linear energy needed for cutting was calculated with regard to paper web properties in intended laser cutting location. Calculated linear cutting energy was verified with series of laser cutting. Practically obtained laser energy needed for cutting deviated from calculated values. This could be explained by difference in heat transfer via radiation in laser cutting and different absorption characteristics of dry and moist paper material. Laser cut samples (both dry and moist (dry matter content about 25-40%)) were tested for strength properties. It was shown that tensile strength and strain break of laser cut samples are similar to corresponding values of non-laser cut samples. Chosen method, however, did not address tensile strength of laser cut edge in particular. Thus, the assumption of improving strength properties with laser cutting was not fully proved. Laser cutting effect on possible pollution of mill broke (recycling of trimmed edge) was carried out. Laser cut samples (both dry and moist) were tested on the content of dirt particles. The tests revealed that accumulation of dust particles on the surface of moist samples can take place. This has to be taken into account to prevent contamination of pulp suspension when trim waste is recycled. Material loss due to evaporation during laser cutting and amount of solid residues after cutting were evaluated. Edge trimming with laser would result in 0.25 kg/h of solid residues and 2.5 kg/h of lost material due to evaporation. Schemes of laser cutting implementation and needed laser equipment were discussed. Generally, laser cutting system would require two laser sources (one laser source for each cutting zone), set of beam transfer and focusing optics and cutting heads. In order to increase reliability of system, it was suggested that each laser source would have double capacity. That would allow to perform cutting employing one laser source working at full capacity for both cutting zones. Laser technology is in required level at the moment and do not require additional development. Moreover, capacity of speed increase is high due to availability high power laser sources what can support the tendency of speed increase of paper making machines. Laser cutting system would require special roll to maintain cutting. The scheme of such roll was proposed as well as roll integration into paper making machine. Laser cutting can be done in location of central roll in press section, before so-called open draw where many web breaks occur, where it has potential to improve runability of a paper making machine. Economic performance of laser cutting was done as comparison of laser cutting system and water jet cutting working in the same conditions. It was revealed that laser cutting would still be about two times more expensive compared to water jet cutting. This is mainly due to high investment cost of laser equipment and poor energy efficiency of CO2 lasers. Another factor is that laser cutting causes material loss due to evaporation whereas water jet cutting almost does not cause material loss. Despite difficulties of laser cutting implementation in paper making machine, its implementation can be beneficial. The crucial role in that is possibility to improve cut edge strength properties and consequently reduce number of web breaks. Capacity of laser cutting to maintain cutting speeds which exceed current speeds of paper making machines what is another argument to consider laser cutting technology in design of new high speed paper making machines.

Paper- and membrane-based ion-modulated electronics

Avhandlingen handlar om pappers- och membranbaserad jonmodulerad elektronik. Målet med forskningen har varit att utveckla billig, miljövänlig och brännbar elektronik, som kan användas i vardagliga engångsprodukter. Baskomponenterna som utvecklas och presenteras i avhandlingen är transistorer och kondensatorer. Mer komplicerad logisk kretselektronik demonstreras också med hjälp av dessa komponenter. Substraten som utnyttjas vid framställningen av dessa elektroniska komponenter är papper och membran. Dessa substrat är flexibla, hållbara, billiga, miljövänliga, etc. och därför väl anpassade för befintliga tryckteknologier. Själva baskomponenterna framställs sedan på dessa substrat genom att trycka flera skikt på varandra, där varje enskilt skikt är ett individuellt material. Detta är möjligt eftersom de organiska materialen som används i dessa komponenter är upplösta i ett lösningsmedel och kan därmed tryckas på samma sätt som ett vanligt bläck. Ett tredimensionellt objekt kan på detta sätt framställas. I avhandlingen presenteras flera olika typer av transistorer, men den gemensamma nämnaren bland dessa är att isolatorn är en jonledare. Denna, ganska ovanliga, transistormodellen har den stora fördelen att lågspänningskomponenter kan relativt enkelt framställas. Det som är speciellt med våra transistorer är att vi har använt miljövänliga jonledare. Detta, bl.a., leder till att våra komponenter visar både god prestanda, tillika som de är miljövänliga. I avhandlingen demonstrerar vi även tryckta superkondensatorer, en motsvarighet till laddningsbara batterier, konstruerade på papper med aktiverat kol och miljövänliga jonledare. De mest komplicerade logiska kretsar som demonstreras i denna avhandling är ring-oscillatorer och 1-bits-minnen konstruerade på papper. --------------------------------------------- Väitöskirja käsittelee paperille ja polymeerikalvolle tulostettua ionimoduloitua elektroniikkaa. Tutkimuksen tavoitteena oli kehittää edullista, ympäristöystävällistä ja polttokelpoista elektroniikkaa, jota voidaan käyttää esim. tavanomaisissa kertakäyttötuotteissa. Väitöskirjassa esitellään erilaisia transistoreita ja kondensaattoreita. Näitä elektronisia peruskomponentteja käyttäen demonstroidaan myös monimutkaisempia loogisia piirejä. Komponenttien valmistuksessa alustana käytettiin paperia ja polymeerikalvoa. Valitut alustat ovat joustavia ja kestäviä, ja ovat siksi hyvin yhteensopivia olemassa olevien tulostusmenetelmien kanssa. Peruskomponentit valmistettiin tulostamalla eri materiaaleja päällekkäin. Komponenteissa käytettävät orgaaniset aineet ovat liuenneessa muodossa musteessa, joka voidaan tulostaa samalla periaatteella kuin mikä tahansa normaali muste. Tällä menetelmällä voidaan valmistaa myös kolmiulotteisia tuotteita. Väitöskirjassa esitellään useita erityyppisiä transistoreita, joissa yhdistävänä tekijänä on ionisesti johtava eriste. Tällaista suhteellisen harvinaista transistorityyppiä käyttämällä voidaan mahdollistaa matala-jännitteisten komponenttien yksinkertainen valmistus. Valmistettujen transistoreiden etu on ionisten nesteiden ympäristöystävällisyys. Elektroniset komponentit ovat täten hyviä suorituskyvyltään, mutteivät haitallisia ympäristölle. Väitöskirjassa demonstroidaan myös tulostettujen superkondensaattoreiden, eli ladattavien paristojen vastineiden, valmistus paperille aktiivihiiltä ja ionisia nesteitä käyttäen. Kaikkein monimutkaisimmat loogiset piirit, jotka tässä väitöskirjassa esitellään, ovat rengasoskillaattorit sekä 1-bittinen paperille valmistettu muisti.

Carbon footprint of recycled paper

Industrial production of pulp and paper is an intensive consumer of energy, natural resources, and chemicals that result in a big carbon footprint of the final product. At present companies and industries aspire to calculate their gas emissions into the atmosphere in order to afterwards reduce atmospheric contamination. One of the approaches allowing to increase carbon burden from the pulp and paper manufacture is paper recycling. The general purpose of the current paper is to establish methods of quantifying and minimizing the carbon footprint of paper. The first target of this research is to derive a mathematical relationship between virgin fibre requirements with respect to the amount of recycled paper used in the pulp. One more purpose is to establish a model to be used to clarify the contribution of recycling and transportation to decreasing carbon dioxide emissions. For this study sensitivity analysis is used to investigate the robustness of obtained results. The results of the present study show that an increasing of recycling rate does not always lead to minimizing the carbon footprint. Additionally, we derived that transportation of waste paper throughout distances longer than 5800 km has no sense because the use of that paper will only increase carbon dioxide emissions and it is better to reject recycling at all. Finally, we designed the model for organization of a new supply chain of paper product to a customer. The models were implemented as reusable MATLAB frameworks.

Evaluation of noni (Morinda citrifolia) volatile profile by dynamic headspace and gas chromatography-mass spectrometry

Noni is a fruit that has interested the scientific community due to its medicinal and functional activities. Different products that contain noni are already in the market, but their consumption could be impaired by their distinctive unpleasant aroma and flavor. The aim of this work was to evaluate the noni pulp volatile profile by dynamic headspace and gas chromatography-mass spectrometry. Thirty seven volatile compounds were detected, mainly alcohols (63.3%), esters (26.9%), cetones (7.4%), and acids (1.2%).

A fast and efficient method for the study of caffeine levels in energy drinks using micellar electrokinetic chromatography (MEKC)

Energy drinks are becoming popular in Brazil and in the world due to their stimulant properties. Caffeine is present in energy drinks with the aim of stimulating the central nervous system and intensifying brain activity. On the other hand, the ingestion of high doses of caffeine can cause undesirable symptoms such as anxiety and tachycardia. Therefore, it is necessary to monitor the caffeine content added to energy drinks to guarantee that the levels in the final product are in accordance with the labeling and within the legislation limits. The goal of this work was to validate a fast, efficient, and low-cost method for the determination of caffeine in energy drinks by micellar electrokinetic chromatography (MEKC). A total of seven brands were analyzed, each in three lots. The electrolyte was prepared with 50 mmol.L-1 of sodium dodecyl sulfate (SDS) and 10 mmol.L-1 of sodium carbonate (pH 11.0). The mean concentration of caffeine ranged from 122.8 to 318.6 mg.L-1. None of the brands had caffeine levels above the maximum limit. Considering the interval of confidence (95%), 72% of the samples had less caffeine than the amount informed on the product label.

Development and validation of a method for detection and quantification of ochratoxin A in green coffee using liquid chromatography coupled to mass spectrometry

A method using Liquid Chromatography Tanden Mass Spectrometry (LC-MS/MS) with matrix-matched calibration curve was developed and validated for determining ochratoxin A (OTA) in green coffee. Linearity was found between 3.0 and 23.0 ng.g-1. Mean recoveries ranged between 90.45% and 108.81%; the relative standard deviation under repeatability and intermediate precision conditions ranged from 5.39% to 9.94% and from 2.20% to 14.34%, respectively. The limits of detection and quantification were 1.2 ng.g-1 and 3.0 ng.g-¹, respectively. The method developed was suitable and contributed to the field of mycotoxin analysis, and it will be used for future production of the Certified Reference Material (CRM) for OTA in coffee.