Ni catalysts with Mo promoter for methane steam reforming

NiO/Al(2)O(3) catalyst precursors were prepared by simultaneous precipitation, in a Ni:Al molar ratio of 3:1, promoted with Mo oxide (0.05, 0.5, 1.0 and 2.0 wt%). The solids were characterized by adsorption of N(2), XRD, TPR, Raman spectroscopy and XPS, then activated by H(2) reduction and tested for the catalytic activity in methane steam reforming. The characterization results showed the presence of NiO and Ni(2)AlO(4) in the bulk and Ni(2)AlO(4) and/or Ni(2)O(3) and MoO(4)(-2) at the surface of the samples. In the catalytic tests, high stability was observed with a reaction feed of 4:1 steam/methane. However, at a steam/methane ratio of 2: 1, only the catalyst with 0.05% Mo remained stable throughout the 500 min of the test. The addition of Mo to Ni catalysts may have a synergistic effect, probably as a result of electron transfer from the molybdenum to the nickel, increasing the electron density of the catalytic site and hence the catalytic activity. (C) 2009 Elsevier Ltd. All rights reserved.

Carbon dioxide reforming of ethanol over Ni/Y(2)O(3)-ZrO(2) catalysts

Supported nickel catalysts of composition Ni/Y(2)O(3)-ZrO(2) were synthesized in one step by the polymerization method and compared with a nickel catalyst prepared by wet impregnation. Stronger interactions were observed in the formed catalysts between NiO species and the oxygen vacancies of the Y(2)O(3)-ZrO(2) in the catalysts made by polymerization, and these were attributed to less agglomeration of the NiO during the synthesis of the catalysts in one step. The dry reforming of ethanol was catalyzed with a maximum CO(2) conversion of 61% on the 5NiYZ catalyst at 800 degrees C, representing a better response than for the catalyst of the same composition prepared by wet impregnation. (C) 2009 Published by Elsevier B.V.

Synthesis, spectral studies and X-ray crystal structure of N,N `-(+/-)-trans-1,2-cyclohexylenebis(3-ethoxysalicylideneamine) H-2(t-3-EtOsalchxn)

The synthesis, spectra and X-ray crystal structure of N,N`-(+/-)-trans-1,2-cyclohexylenebis(3-ethoxysalicylideneamine) H-2(t-3-EtOsalchxn), a salen-type ligand, are reported. The Schiff base was characterized by elemental analysis, m.p., IR, electronic spectra, H-1 and C-13 NMR spectra. The spectra are discussed and compared with those of N,N`-(+/-)-trans-1,2-cyclohexylenebis(salicylideneamine), H-2(t-salchxn). The electronic and IR spectra were also resolved by deconvolution. The influence of the ethoxy group on the IR, electronic spectrum, H-1 and C-13 NMR spectra is discussed. Strong intramolecular forces are present as supported by the IR and H-1 NMR spectra and the X-ray crystal structure. An intermolecular hydrogen bond is observed and appears twice in a pair of molecules in the unit cell. (c) 2007 Elsevier B.V. All rights reserved.

Organic additive-copper(II) complexes as plating precursors

Cu(II) ions previously coordinated with typical electroplating organic additives were investigated as an alternative source of metal for plating bath. The coordination complexes were isolated from reaction between CuSO(4) and organic additives as ligands (oxalate ion, ethylenediamine or imidazole). Deposits over 1010 steel were successfully obtained from electroplated baths using the complexes without any addition of free additives, at pH = 4.5 (H(2)SO(4)/Na(2)SO(4)). These deposits showed better morphologies than deposits obtained from CuSO(4) solution either in the absence or presence of oxalate ion as additive (40 mmol L(-1)), at pH = 4.5 (H(2)SO(4)/Na(2)SO(4))It is suggestive that the starting metal plating coordinated with additives influences the electrode position processes, providing deposits with corrosion potentials shifted over + 200 mV in 0.5 mol L(-1) NaCl (1 mV s(-1)). The resistance against corrosion is sensitive to the type of additive-complex used as precursor. The complex with ethylenediamine presented the best deposit results with the lowest pitting potential (-0.27 V vs 3.0 mol L(-1) CE). It was concluded that the addition of free additives to the electrodeposition baths is not necessary when working with previously coordinated additives. Thus, the complexes generated in ex-situ are good alternatives as plating precursors for electrodeposition bath. (C) 2009 Elsevier B.V. All rights reserved.

Optical Characterization and Optimization of Display Components : Some Applications to Liquid-Crystal-Based and Electrochromics-Based Devices

This dissertation is focused on theoretical and experimental studies of optical properties of materials and multilayer structures composing liquid crystal displays (LCDs) and electrochromic (EC) devices. By applying spectroscopic ellipsometry, we have determined the optical constants of thin films of electrochromic tungsten oxide (WOx) and nickel oxide (NiOy), the films’ thickness and roughness. These films, which were obtained at spattering conditions possess high transmittance that is important for achieving good visibility and high contrast in an EC device. Another application of the general spectroscopic ellipsometry relates to the study of a photo-alignment layer of a mixture of azo-dyes SD-1 and SDA-2. We have found the optical constants of this mixture before and after illuminating it by polarized UV light. The results obtained confirm the diffusion model to explain the formation of the photo-induced order in azo-dye films. We have developed new techniques for fast characterization of twisted nematic LC cells in transmissive and reflective modes. Our techniques are based on the characteristics functions that we have introduced for determination of parameters of non-uniform birefringent media. These characteristic functions are found by simple procedures and can be utilised for simultaneous determination of retardation, its wavelength dispersion, and twist angle, as well as for solving associated optimization problems. Cholesteric LCD that possesses some unique properties, such as bistability and good selective scattering, however, has a disadvantage – relatively high driving voltage (tens of volts). The way we propose to reduce the driving voltage consists of applying a stack of thin (~1µm) LC layers. We have studied the ability of a layer of a surface stabilized ferroelectric liquid crystal coupled with several retardation plates for birefringent color generation. We have demonstrated that in order to accomplish good color characteristics and high brightness of the display, one or two retardation plates are sufficient.

Overexpression and Purification of the Oat (Avena Fatua) Protein AFN1 and Construction of a pMAL/AFN1 Expression Plasmid

Abscisic acid (ABA) is an important phytohormone with regulatory roles in many physiological processes. ABA expression is induced by environmental stresses such as drought and it is known to be an inhibitor of seed germination. A wild oat (Avena fatua) called AFN1 has been hypothesized to initiate the early stages of germination as its mRNA accumulates in nondormant seed embryos during imbibition. The polypeptide sequence of AFN1 suggests that it is an ABA glucosyl transferase. Glucosylation by AFN1 and thereby inactivation of ABA could lead to seed germination. In order to understand the role of AFN1 in germination, an ample quantity of AFN1 polypeptide is needed to test for enzymatic ABA glucosylase activity. My work has been to overexpress recombinant AFN1containing a (His)6 tag using a pRSETC E.coli expression system followed by Purification of the AFN1 protein by means of a nickel-affinity column that bind to the (His)6 tag. Due to the insufficient yield of AFN1 fusion protein obtained with this procedure, another method using a pMAL-c2x vector is now being employed. The pMAL expression system provides a method for expressing and purifying protein by tagging proteins with maltose-binding protein (MBP). It is anticipated that MBP tag will be advantageous as it can make the fusion protein more soluble and thereby yield a larger quantity of protein. Currently, work is underway on the construction of pMAL/AFN1 plasmid.

Estudo da associação de elementos traços com a fração orgânica e inorgânica do carvão do leão

O presente trabalho refere-se à determinação dos elementos cobre, chumbo, zinco, cobalto, níquel, cromo, vanádio e manganês no carvão da Mina do Leão, com o objetivo de verificar a distribuição e ocorrência dos mesmos, com ênfase ao estudo da associação com as frações orgânica e inorgânica do carvão. O estudo da associação revelou que o cobre, cobalto, níquel, cromo e vanádio, estão associados à fração orgânica do carvão. O chumbo e o zinco, estão predominantemente associados a fração orgânica, contudo, para altos teores de cinzas, verifica-se também associação com a fração inorgânica. O manganês, está dominantemente associado à fração inorgânica.

Avaliação da genotoxicidade induzida por emissões de veículos automotores - Ctenomys minutus como organismo bioindicador

Existe um número crescente de componentes químicos lançados ao meio ambiente, muitos dos quais são capazes de induzir efeitos danosos adversos à saúde de animais e humanos, representando uma causa importante de preocupação por seus possíveis efeitos a longo prazo. O impacto ecológico e os riscos a saúde dos organismos associados com a exposição a poluentes ambientais são extremamente difíceis de se avaliar devido a muitos desses componentes serem parte de misturas complexas. Os gases produzidos pelos motores dos veículos à combustão contém diversos poluentes sabidamente genotóxicos, como óxidos de nitrogênio (NOX), monóxido de carbono (CO), óxidos de enxofre (SOx), hidrocarbonetos (HC) e seus derivados, bem como particulados, e metais (cádmio, cromo, cobre, níquel, vanádio, zinco e chumbo). Todos esses compostos isolados ou associados a outros elementos são tóxicos ou de efeito danoso aos organismos, de forma não totalmente esclarecida. Este estudo teve como objetivo verificar o possível efeito genotóxico das emissões dos automóveis em roedor nativo Ctenomys minutus cronicamente exposto, através do Ensaio Cometa (EC), comparando os resultados com o Teste de Micronúcleos (MN), ambos em sangue periférico. Levando em consideração alguns fatores que pudessem influenciar os resultados dos testes de genotoxicidade, este trabalho ainda teve como objetivos: identificar a presença de alguns agentes envolvidos na poluição gerada pelos veículos; verificar possíveis diferenças sazonais, como temperatura e ventos; e se existe influência da idade e sexo dos roedores. Os C. minutus (Octodontidae-Rodentia), foram capturados em dois campos diferentes, ambos ao lado da estrada RS/030, na cidade de Osório, Estado do Rio Grande do Sul (RS): (a) Amaral, e (b) Weber. Animais para controle externo foram capturados no Campo Maribo à cerca de 3 km de distância de outra estrada (RS/389-Osório/RS), conseqüentemente afastada das emissões dos veículos. No final do período desse estudo, foram capturados 123 animais (73 fêmeas e 50 machos).

Early and post transition metal complexes as a single of combined components in the ethylene and isoprene polynerization

In this work is reported, in a first step, the effect of different experimental parameters and their relation with polymer properties using the homogeneous binary catalyst system composed by Ni(α-diimine)Cl2 (α-diimine = 1,4-bis(2,6-diisopropylphenyl)- acenaphthenediimine) and {TpMs*}V(Ntbu)Cl2 (TpMs* = hydridobis(3-mesitylpyrazol-1- yl)(5-mesitylpyrazol-1-yl)) activated with MAO. This complexes combination produces, in a single reactor, polyethylene blends with different and controlled properties dependent on the polymerization temperature, solvent and Nickel molar fraction (xNi). In second, the control of linear low density polyethylene (LLDPE) production was possible, using a combination of catalyst precursors {TpMs}NiCl (TpMs = hydridotris(3- mesitylpyrazol-1-yl)) and Cp2ZrCl2, activated with MAO/TMA, as Tandem catalytic system. The catalytic activities as well as the polymer properties are dependent on xNi. Polyethylene with different Mw and controlled branches is produced only with ethylene monomer. Last, the application group 3 metals catalysts based, M(allyl)2Cl(MgCl2)2.4THF (M = Nd, La and Y), in isoprene polymerization with different cocatalysts systems and experimental parameters is reported. High yields and polyisoprene with good and controlled properties were produced. The metal center, cocatalysts and the experimental parameters are determinant for the polymers properties and their control. High conversions in cis-1,4- or trans-1,4-polyisoprene were obtained and the polymer microstructure depending of cocatalyst and metal type. Combinations of Y and La precursors were effective systems for the cis/transpolyisoprene blends production, and the control of cis-trans-1,4-microstructures by Yttrium molar fraction (xY) variation was possible.

Regendo a atividade regulatória: a nova legislação das agências reguladoras federais no Brasil

Os processos e as instituições regulatórias são assuntos prioritários da agenda governamental, por tratarem-se de assunto dinâmico que envolve uma mudança na cultura administrativa do país. Um dos grandes desafios das agências reguladoras brasileiras tem sido desempenhar suas funções de forma autônoma e imparcial com o objetivo de promover confiança e transparência ao mercado e à sociedade. Este estudo buscou realizar uma análise do conteúdo e das repercussões das mudanças ora em curso no Brasil, em especial daquelas contidas na proposta enviada pelo governo federal brasileiro ao Congresso Nacional dispondo sobre a nova Lei Geral das Agências reguladoras (Projeto de Lei 3337/2004), com o fito de promover mudanças no modelo de organização institucional e funcionamento desses entes regulatórios. Com esse fim, de início, foram descritos os fundamentos teóricos da regulação, com a apresentação do processo de criação das agências reguladoras federais brasileiras e suas características determinantes. Após a fundamentação, foram detalhados os pontos principais do Projeto de Lei 3337/2004, e seu substitutivo, elaborado pelo Deputado Leonardo Picciani. O próximo capítulo, Governança Regulatória, apresentou as políticas de reforma regulatória, seus desafios no Brasil, e delineou o Programa de Fortalecimento da Capacidade Institucional para Gestão em Regulação (PRO-REG). O estudo deu prosseguimento à análise por meio da apresentação das boas práticas à qualidade regulatória, enfatizando a importância da participação social no processo regulatório, e também da abordagem da experiência internacional. Item complementar para a compreensão e visão geral do estudo, a supervisão regulatória foi também conceituada e justificada, seguida pela abordagem da criação da Unidade de Supervisão Central e da experiência internacional. Por último, em análise final do tema, apoiada por grande pesquisa bibliográfica e documental, e por entrevistas concedidas pelos ocupantes dos dois maiores cargos da Superintendência de Abastecimento da Agência Nacional do Petróleo, Gás Natural e Biocombustíveis, procurou-se mostrar a imprescindibilidade do desenvolvimento e implementação de uma estratégia de qualidade regulatória que permita uma abordagem consistente.

Novel catalyst systems based on Ni(II), Ti(IV), and Cr(III) complexes for oligo-and polymerization of ethylene

The complex of Brookhart Ni(α-diimine)Cl2 (1) (α-diimine = 1,4-bis(2,6- diisopropylphenyl)-acenaphthenediimine) has been characterized after impregnation on silica (S1) and MAO-modified silicas (4.0, 8.0 and 23.0 wts.% Al/SiO2 called S2, S3 and S4, respectively). The treatment of these heterogeneous systems with MAO produces some active catalysts for the polymerization of the ethylene. A high catalytic activity has been gotten while using the system supported 1/S3 (196 kg of PE/mol[Ni].h.atm; toluene, Al/Ni = 1000, 30ºC, 60 min and atmospheric pressure of ethylene). The effects of polymerization conditions have been tested with the catalyst supported in S2 and the best catalytic activity has been gotten with solvent hexane, MAO as cocatalyst, molar ratio Al/Ni of 1000 and to the temperature of 30°C (285 kg of PE/mol[Ni].h.atm). When the reaction has been driven according to the in situ methodology, the activity practically doubled and polymers showed some similar properties. Polymers products by the supported catalysts showed the absence of melting fusion, results similar to those gotten with the homogeneous systems by DSC analysis. But then, polymers gotten with the transplanted system present according to the GPC’s curves the polydispersity (MwD) varies between 1.7 and 7.0. A polyethylene blend (BPE/LPE) was prepared using the complex Ni(α-diimine)Cl2 (1) (α-diimine = 1,4-bis(2,6-diisopropylphenyl)-acenaphthenediimine) and {TpMs*}TiCl3 (2) (TpMs* = hydridobis(3-mesitylpyrazol-1-yl)(5-mesitylpyrazol-1-yl)) supported in situ on MAO-modified silica (4.0 wts. -% Al/SiO2, S2). Reactions of polymerization of ethylene have been executed in the toluene in two different temperatures (0 and 30°C), varying the molars fraction of nickel (xNi), and using MAO as external cocatalyst. To all temperatures, the activities show a linear variation tendency with xNi and indicate the absence of the effect synergic between the species of nickel and the titanium. The maximum of activity have been found at 0°C. The melting temperature for the blends of polyethylene produced at 0 °C decrease whereas xNi increases indicating a good compatibility between phases of the polyethylene gotten with the two catalysts. The melting temperature for the blends of polyethylene showed be depend on the order according to which catalysts have been supported on the MAO-modified silica. The initial immobilization of 1 on the support (2/1/S2) product of polymers with a melting temperature (Tm) lower to the one of the polymer gotten when the titanium has been supported inicially (1/2/S2). The observation of polyethylenes gotten with the two systems (2/1/S2 and 1/2/S2) by scanning electron microscopy (SEM) showed the spherical polymer formation showing that the spherical morphology of the support to been reproduced. Are described the synthesis, the characterization and the catalytic properties for the oligomerization of the ethylene of four organometallics compounds of CrIII with ligands ([bis[2-(3,5-dimethyl-1-pyrazolyl)ethyl]amine] chromium (III) chloride (3a), [bis[2-(3,5- dimethyl-l-pyrazolyl)ethyl]benzylamine] chromium (III) chloride (3b), [bis[2-(3,5-dimethyl-lpyrazolyl) ethyl]ether] chromiun(III)chloride (3c), [bis[2-(3-phenyl-lpyrazolyl) ethyl]ether]chromiun(III)chloride (3d)). In relation of the oligomerization, at exception made of the compounds 3a, all complex of the chromium showed be active after activation with MAO and the TOF gotten have one effect differentiated to those formed with CrCl3(thf)3. The coordination of a tridentate ligand on the metallic center doesn't provoke any considerable changes on the formation of the C4 and C6, but the amount of C8 are decrease and the C10 and C12+ have increased. The Polymers produced by the catalyst 3a to 3 and 20 bar of ethylene have, according to analyses by DSC, the temperatures of fusion of 133,8 and 136ºC respectively. It indicates that in the two cases the production of high density polyethylene. The molar mass, gotten by GPC, is 46647 g/mols with MwD = 2,4 (3 bar). The system 3c/MAO showed values of TOF, activity and selectivity to different α-olefins according to the pressure of ethylene uses. Himself that shown a big sensibility to the concentration of ethylene solubilized.

Vermiculitas tratadas quimicamente na obtenção de sólidos microporosos como precursores para híbridos inorgânico-orgânicos com aplicações adsortivas

ALVES, Ana paula Melo. Vermiculitas tratadas quimicamente na obtenção de sólidos microporosos como precursores para híbridos inorgânico-orgânicos com aplicações adsortivas. 2009. 124 f. Tese (Doutorado em Quimica) - Centro de Ciências Exatas e da Natureza, Universidade Federal da Paraíba, João Pessoa, PB, 2009.

Clonagem e expressão do gene que codifica o inibidor de quimotripsina de Erythrina velutina WILLD. - caracterização e avaliação de seu potencial farmacológico

Proteinases are enzymes distributed widely founded in several organisms and perform many different functions, from maintaining homeostasis to the worsening of some diseases such as cancer, autoimmune diseases and infections. The proteins responsible of controlling the action of these enzymes are the inhibitors, that are classified based on their target proteases and are founded since simple organisms, such as bacteria, to higher organisms, such as larger plants and mammals. Plant proteinase inhibitors act by reducing or inactivating the activity of target proteases, thus, these proteins have been studied as potential tools in the treatment of diseases related to protease activities. In this context, an inhibitor of chymotrypsin from Erythrina velutina, called EvCI was previously purified and it was observed that this protein plays in vitro anticoagulant activity and anti-inflammatory activity in in vivo model. Aiming to reduce the environmental impact caused by the purification EvCI in high amounts and to facilitate the process of obtaining this protein, the recombinant chymotrypsin inhibitor from Eryhrina velutina was produced after cloning and expression in Escherichia coli. The bacteria were grown in LB medium and after induction of the expression this material was subjected to procedures for cell lysis and the product was applied on Nickel-affinity column. The proteins adsorbed were digested by thrombin and applied on Chymotrypsin-Sepharose affinity column, obtaining the purified inhibitor, named recEvCI. After electrophoresis, the recombinant inhibitor showed an approximately molecular mass of 17 kDa, and reduced the chymotrypsin and elastase activities in vitro. The recombinant inhibitor was sequenced and was found similar amino acids residues when compared to other inhibitors deposited in the database, with some modifications. recEvCI showed high stability under pH variations and reducing conditions, maintaining its activity around 80%. This protein increased the blood coagulation time in vitro by acting on the intrinsic pathway and did not show cytotoxicity against strains of mouse 3T3 fibroblasts and RAW 264.7 macrophages. recEvCI showed microbicide activity related to release of nitric oxide and consequently the activation of macrophages, futhermore having proinflammatory effects assessed by increased release of TNF-α. These results indicate that recEvCI can be biotechnologically used as a new tool in the control of coagulation-related diseases as well as can be an activating agent of the immune system in immunosuppressed individuals