Obtenção e caracterização de dióxido de estanho nanoestruturado pelo método de síntese contínua por combustão em solução

Continuous Synthesis by Solution Combustion was employed in this work aiming to obtain tin dioxide nanostructured. Basically, a precursor solution is prepared and then be atomized and sprayed into the flame, where its combustion occurs, leading to the formation of particles. This is a recent technique that shows an enormous potential in oxides deposition, mainly by the low cost of equipment and precursors employed. The tin dioxide (SnO2) nanostructured has been widely used in various applications, especially as gas sensors and varistors. In the case of sensors based on semiconducting ceramics, where surface reactions are responsible for the detection of gases, the importance of surface area and particle size is even greater. The preference for a nanostructured material is based on its significant increase in surface area compared to conventional microcrystalline powders and small particle size, which may benefit certain properties such as high electrical conductivity, high thermal stability, mechanical and chemical. In this work, were employed as precursor solution tin chloride dehydrate diluted in anhydrous ethyl alcohol. Were utilized molar ratio chloride/solvent of 0,75 with the purpose of investigate its influence in the microstructure of produced powder. The solution precursor flux was 3 mL/min. Analysis with X-ray diffraction appointed that a solution precursor with molar ratio chloride/solvent of 0,75 leads to crystalline powder with single phase and all peaks are attributed to phase SnO2. Parameters as distance from the flame with atomizer distance from the capture system with the pilot, molar ratio and solution flux doesn t affect the presence of tin dioxide in the produced powder. In the characterization of the obtained powder techniques were used as thermogravimetric (TGA) and thermodiferential analysis (DTA), particle size by laser diffraction (GDL), crystallographic analysis by X-ray diffraction (XRD), morphology by scanning electron microscopy (SEM), transmission electron microscopy (TEM), specific surface area (BET) and electrical conductivity analysis. The techniques used revealed that the SnO2 exhibits behavior of a semiconductor material, and a potentially promising material for application as varistor and sensor systems for gas

Influência de tratamentos térmicos no comportamento mecânico da blenda poli(metacrilato de metila) / poli(tereftalato de etileno) reciclado

Studies indicate that a variation in the degree of crystallinity of the components of a polymer blend influences the mechanical properties. This variation can be obtained by subjecting the blend to heat treatments that lead to changes in the spherulitic structure. The aim of this work is to analyze the influence of different heat treatments on the variation of the degree of crystallinity and to establish a relationship between this variation and the mechanical behavior of poly(methyl methacrylate)/poly(ethylene terephthalate) recycled (PMMA / PETrec) with and without the use of compatibilizer agent poly(methyl methacrylate-al-glycidyl methacrylate-al-ethyl acrylate) (MMAGMA- EA). All compositions were subjected to two heat treatments. T1 heat treatment the samples were treated at 130 ° C for 30 minutes and cooled in air. In T2, the samples were treated at 230 ° C for 5 minutes and cooled to approximately -10 ° C. The variation of the degree of crystallinity was determined by the proportional relationship between crystallinity and density, with the density measured by pycnometry. The mechanical behavior was verified by tensile tests with and without the presence of notches and pre-cracks, and by method of fracture toughness in plane strain (KIC). We used the scanning electron microscopy (SEM) to analyze the fracture surface of the samples. The compositions subjected to heat treatment T1, in general, showed an increase in the degree of crystallinity in tensile strength and a tendency to decrease in toughness, while compositions undergoing treatment T2 showed that the opposite behavior. Therefore, this work showed that heat treatment can give a polymer blend further diversity of its properties, this being caused by changes in the crystal structure

Processamento e caracterização da blenda poli (metacrilato de metila) (PMMA) elastomerico e poli (tereftalato de etileno) (PET) pós-consumo

This work studied the immiscible blend of elastomeric poly(methyl methacrylate) (PMMA) with poly(ethylene terephthalate) (PET) bottle grade with and without the use of compatibilizer agent, poly(methyl methacrylate-co-glycidyl methacrylate - co-ethyl acrylate) (MGE). The characterizations of torque rheometry, melt flow index measurement (MFI), measuring the density and the degree of cristallinity by pycnometry, tensile testing, method of work essential fracture (EWF), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were performed in pure polymer and blends PMMA/PET. The rheological results showed evidence of signs of chemical reaction between the epoxy group MGE with the end groups of the PET chains and also to the elastomeric phase of PMMA. The increase in the concentration of PET reduced torque and adding MGE increased the torque of the blend of PMMA/PET. The results of the MFI also show that elastomeric PMMA showed lower flow and thus higher viscosity than PET. In the results of picnometry observed that increasing the percentage of PET resulted in an increase in density and degree crystallinity of the blends PMMA/PET. The tensile test showed that increasing the percentage of PET resulted in an increase in ultimate strength and elastic modulus and decrease in elongation at break. However, in the phase inversion, where the blend showed evidence of a co-continuous morphology and also, with 30% PET dispersed phase and compatibilized with 5% MGE, there were significant results elongation at break compared to elastomeric PMMA. The applicability of the method of essential work of fracture was shown to be possible for most formulations. And it was observed that with increasing elastomeric PMMA in the formulations of the blends there was an improvement in specific amounts of essential work of fracture (We) and a decrease in the values of specific non-essential work of fracture (βWp)

Novos monômeros obtidos a partir do metacrilato de glicidila, bisfenol A e 4, 4 isopropilidenodicicloexanol : síntese, caracterização estrutural e propriedades de compósitos para utilização em resinas de restauração dental

Nowadays, composite resins are the direct restorative materials more important in dental clinical performance, due to their versatility and aesthetic excellence. Bis-GMA (2,2-bis[4(2-hydroxy-3-metacryloxypropoxy)phenil]propane) is the base monomer more frequently used in restorative composite resins. However, this monomer presents some disadvantages, such as high viscosity and two aromatic rings in its structure that can promote allergic reactions to the humans. In this work, the main purpose was to synthesize new monomers from glycidyl methacrylate to use in dental restorative materials. Structural characterization of the monomers was carried out through FTIR and NMR 1H, and eight composites were produced from the new monomers, by addition of silane-treated alumino silicate particles (inorganic filler) and a photocuring system (camphorquinone and ethyl 4-dimethylaminebenzoate). The composites were analyzed by environmental scanning electronic microscopy and the water sorption and solubility, compressive strength and elastic modulus were determined. A commercial composite resin [Z100 (3M)] was used to comparison effect. The new composites presented general characteristics similar to the commercial ones; however, they didn t present the properties expected. This behavior was attributed to the lower degree of monomer reaction and to the granulometry and size distribution of the mineral filler in the polymeric matrix

Síntese, caracterização e aplicação de LaSBA-15 e como catalisador para obtenção de biodiesel de soja via rota etílica

Biodiesel is an alternative fuel, renewable, biodegradable and nontoxic. The transesterification of vegetable oils or animal fat with alcohol is most common form of production of this fuel. The procedure for production of biodiesel occurs most commonly through the transesterification reaction in which catalysts are used to accelerate and increase their income and may be basic, acid or enzyme. The use of homogeneous catalysis requires specific conditions and purification steps of the reaction products (alkyl ester and glycerol) and removal of the catalyst at the end of the reaction. As an alternative to improve the yield of the transesterification reaction, minimize the cost of production is that many studies are being conducted with the application of heterogeneous catalysis. The use of nano-structured materials as catalysts in the production of biodiesel is a biofuel alternative for a similar to mineral diesel. Although slower, can esterify transesterified triglycerides and free fatty acids and suffer little influence of water, which may be present in the raw material. This study aimed at the synthesis, characterization and application of nano-structured materials as catalysts in the transesterification reaction of soybean oil to produce biodiesel by ethylic route. The type material containing SBA-15 mesoporous lanthanum embedded within rightly Si / La = 50 was used catalyst. Solid samples were characterized by X-ray diffraction, thermogravimetric analysis, infrared spectroscopy, nitrogen adsorption and desorption. For the transesterification process, we used a molar ratio of 20:1 alcohol and oil with 0.250 g of catalyst at 60°C and times of 6 hours of reaction. It was determined the content of ethyl esters by H-NMR analysis and gas chromatography. It was found that the variable of conversion obtained was 80%, showing a good catalytic activity LaSBA-15 in the transesterification of vegetable oils via ethylic route

Efeitos da aplicação de herbicidas sobre a eficiência fotoquímica em plantas de soja convencional e geneticamente modificada

Objetivou-se, neste trabalho, avaliar o efeito da aplicação de herbicidas em pós-emergência sobre a eficiência fotoquímica de duas cultivares de soja (M-SOY 7908 RR e M-SOY 8001). O delineamento experimental utilizado foi em blocos ao acaso, com quatro repetições. Os tratamentos constaram da aplicação de herbicidas isolados e em misturas: lactofen, glyphosate, lactofen + chlorimuron-ethyl, chlorimuron-ethyl + imazethapyr, chlorimuron-ethyl + bentazon, glyphosate + imazethapyr, lactofen + chlorimuron-ethyl + imazethapyr e lactofen + chlorimuron-ethyl + imazethapyr/haloxyfop-methyl. Além disso, foram mantidas duas testemunhas sem aplicação de herbicida. As avaliações foram realizadas aos 4; 11; 18; 25 e 32 dias após aplicação dos herbicidas (DAA) no primeiro ano, e aos 6, 14, 21, 28 e 35 DAA, no segundo. A cultivar M-SOY 8001 foi suscetível à aplicação dos herbicidas, principalmente às misturas contendo lactofen + chlorimuron-ethyl e lactofen + chlorimuron-ethyl + imazethapyr + haloxifop-methyl, os quais provocaram redução no rendimento quântico máximo do PSII (Fv/Fm). As duas cultivares apresentaram suscetibilidade aos herbicidas quando tratados com lactofen aplicado isolado e nas misturas lactofen + chlorimuron-ethyl, chlorimuron-ethyl + imazethapyr, lactofen + chlorimuron-ethyl + imazethapyr e lactofen + chlorimuron-ethyl + imazethapyr + haloxifop-methyl com redução nos teores de clorofila, estimados pelo Medidor Portátil de Clorofilas. Os danos foram reversíveis, desaparecendo gradativamente com a idade das plantas.

Processo de desidratação da alga Gracilaria birdiae beneficiada em laboratório e artesanalmente: análise da atividade antioxidante e composição centesimal

The main aim of this study was to compare the procedure for dehydration of Gracilaria birdiae prepared handmade and laboratory, collected in the northern coast of Rio Grande do Norte. The sample was collected in the Rio do Fogo beach in march 2009. The sample collected followed by two processing, the first the material prepared in laboratory was air-dried at 50°C for 24 hours in air-flow oven. The second the handmade sample was air-dried on the sun during three days. The extract was prepared in three different solvents: ethanol, hydroethanol and water, resulting in ethanol, hidroethanol and aqueous extracts from handmade and laboratory sample. In according with results only the ethanol extract was fractionated yielding the fractions hexane, dichloromethane and ethyl acetate fractions. The different process to obtain Gracilaria birdiae resulted in the samples with different shades. The soluble solids content was higher in the laboratory sample. The chemical composition the both samples were characterized by presenting a considerable amounts of carbohydrates, with amior percentage protein and ash, respectively, in the handmade and laboratory sample. In two samples showed a low content of lipids and the lipid profile showed a higher proportion of monounsaturated fatty acids, with the absence polyunsaturated handmade sample. The phytochemical screening by chemical reactions showed the presence of flavonoids, tannins, alkaloids and saponins the laboratory sample, presenting a greater diversity of bioactive compounds. Through of the analysis by thin layer chromatography was possible to identify the phytosterols β-sitosterol and stigmasterol the both samples, also suggest the presence of β-carotene and chlorophyll α the laboratory sample. The levels of total phenolics and flavonoids were more significant in the ethanol extract of the laboratory sample. The in vitro lethality showed that extracts of the laboratory sample and handmade from 125 to 500 μg/ mL, respectively, were highly lethal. In the evaluation of antioxidant capacity by the system β-carotene/ácido linoleic method and by DPPH radical scavernging assay, the ethanol extract from the laboratory process showed significantly greater activity than the other extracts, being and the first and second methods, respectively, lower and equivalent to the synthetic antioxidant BHT. The handmade ethanol extract has not demonstrated skill in deactivating free radicals, but showed activity in inhibiting lipid peroxidation, although the values were significantly lower than the laboratory sample. We conclude that the dehydration process in the laboratory is the most efficient technique to maintenance of the chemical composition present in the seaweed, providing beneficial properties such as antioxidant capacity. We emphasize that this property can be explored with the objective of adding commercial value to the final product, which will promote the expansion of production of this seaweed in the community of Rio do Fogo

Caracterização e quantificação de marcadores químicos do extrato hidroetanólico das folhas de Kalanchoe brasiliensis Cambess

Kalanchoe brasiliensis Cambess (Crassulaceae), commonly known as saião , coirama branca , folha grossa , is originally from Brazil and commonly found in São Paulo to Bahia, mainly in the coastal zone. Regarding of biological activities, most preclinical studies were found in the literature, mainly about the anti-inflammatory activity of extracts obtained from leaves and / or aerial parts of K. brasiliensis. As regards the chemical constitution, it has been reported mainly the presence of flavonoids in the leaves of the species, but until this moment did not knows which are the active compounds. Although it is a species widely used in traditional medicine in Brazil, there is no monograph about the quality parameters of the plant drug. In this context, this study aims to characterize and quantify the chemical markers of hydroethanolic extract (HE) from the leaves of K. brasiliensis, which can be used in quality control of plant drug and derivatives obtained from this species. The methodology was divided into two parts: i. Phytochemical study: to fractionate, isolate and characterizate of the chemical (s) marker (s) of the HE from the leaves of K. brasiliensis; ii. To Developed validate of analytical method by High Performance Liquid Chromatography (HPLC)-diode array detector (DAD) to quantify the chemical (s) marker (s) of the EH. i. The EH 50% was prepared by turbo extraction method. It was then submitted to liquid-liquid partition, obtaining dichloromethane, n-butanol and ethyl acetate (AcOEt) fractions. The AcOEt fraction was selected to continue the fractionation process, because it has a chemical profile rich in flavonoids. The acOEt fraction was submitted to column chromatography using different systems for obtaining the compound Kb1. To identify this compound, it was submitted to UV analysis ii. For quantitative analysis, the EH was analyzed by HPLC, using different methods. After selecting the most appropriate method, which showed satisfactory resolution and symmetrical peaks, it was validated according to parameters in the RE 899/2003. As result, it was obtained from the AcOEt fraction the compound Kb1 (2.7 mg). Until this moment, the basic nucleus was characterized by UV analysis using shift reagents. The partial chemical structure of the compound Kb1 was identified as a flavonol, containing hydroxyls in 3 , 4 position (ring A), 5 and 7 free (ring B) and a replacement of the C3 hydroxyl by a sugar. As the analysis were performed in the HPLC coupled to a DAD, we observed that the UV spectrum of the major peaks of EH from K. brasiliensis shown similar UV spectrum. According to the literature, it has been reported the presence of patuletin glycosydes derivatives in the leaves of this species. Therefore, it is suggested that the compound Kb1 is glycosylated patuletin derivative. Probably the sugar (s) unit(s) are linked in the C3 in the C ring. . Regarding the development of HPLC analytical method, the system used consists of phase A: water: formic acid (99,7:0,3, v / v) and phase B: methanol: formic acid (99,7:0,3, v / v), elution gradient of 40% B - 58% B in 50 minutes, ccolumn (Hichrom ®) C18 (250x4, 0 mm, 5 μm), flow rate 0.8 mL / min, UV detection at 370 nm, temperature 25 ° C. In the analysis performed with the co-injection of thecompound Kb1 + HE of K. brasiliensis was observed that it is one of the major compounds with a retention time of 12.47 minutes and had a content of 15.3% in EH of leaves from K. brasiliensis. The method proved to be linear, precise, accurate and reproducible. According to these results, it was observed that compound Kb1 can be used as a chemical marker of EH from leaves of K. brasiliensis, to assist in quality control of drug plant and its derivatives

Caracterização dos marcadores químicos e avaliação de atividades biológicas do extrato de Spondias mombim

Spondias mombin is a fruitful species dispersed in tropical regions of America, Africa and Asia. In Brazil, the species can be found mainly in the northern and northeastern regions. Scarce chemical and pharmacological studies have been reported for S. mombin and until this moment studies about chemical markers were not developed. In this context, the aims of this study were to characterize the chemical markers from S. mombin leaves and evaluate their anti-inflammatory, antioxidant and antiproliferative potentials. The chemical profile of the hydroethanolic extract from S. mombin leaves analyzed by HPLC-DAD, through a validated method, allowed the identification and quantification of ellagic acid and chlorogenic acid. This extract showed anti-inflammatory potential in acute peritonitis model induced by carrageenan. The hydroethanolic extract from S. mombin leaves was subjected to a liquid-liquid partition with the solvents: n-hexane, dichloromethane, ethyl acetate and n-butanol. Regarding the anti-inflammatory potential of the fractions obtained they were active; however, ethyl acetate fraction at 200 mg/kg showed highlighted results. The compounds ellagic acid and chlorogenic acid also inhibited the leukocyte migration to the site of inflammation at 2.5, 5 and 10 mg/kg. The hydroethanolic extract, fractions and the chemical markers showed significant antioxidant potential when evaluated in different assays: DPPH Free-Radical Scavenging, Superoxide Radical Scavenging, Hydroxyl Radicals Scavenging and Reducing Power. Taken together our results showed that hydroethanolic extract of S. mombin leaves has ellagic acid and chlorogenic acid as bioactive markers and it demonstrated antiinflammatory and antioxidant properties besides no cytotoxicity against 3T3 cells. It enables us to suggest S. mombin as an important species to develop herbal drugs

Capacidade antioxidante in vitro e avaliação da toxicidade aguda in vivo de extratos de folhas de Licania rígida Benth., Licania tomentosa (Benth.) Fritsch e Couepia impressa Prance (Chrysobalanaceae)

Licania rigida Benth., Licania tomentosa (Benth.) Fritsch, and Couepia impressa Prance (Chrysobalanaceae family) plants have long been used medicinally by the people from Northeastern Brazil. Crude extracts and infusions of these plants have been applied in the treatment of several conditions such as diabetes and rheumatism, degenerative diseases with involvement of reactive oxygen species (ROS). The aim of this study was to evaluate the aqueous, ethanolic, and hydroethanolic leaves extracts antioxidant capacity of these species, using several in vitro assay systems (reducing power, DPPH● scavenging, the β-carotene linoleate model system and lipid peroxidation inhibition in rat brain homogenate, using thiobarbituric acid reactive substances - TBARS). The oral acute toxicity of aqueous extracts was also evaluated in vivo. Results revealed that these extracts possess a potent reducing power and DPPH scavenging ability, as well as the ability to prevent TBARS formation in rat brain homogenate in a concentration-dependent manner. Regarding in vivo oral acute toxicity of the aqueous species extracts, no toxic effects were observed upon evaluating physiological, hematological and biochemical parameters. The presence of high levels of phenolics and flavonoids was determined mainly in the ethanol extract. However, the C. impressa hydroethanolic extract, fractionated with hexane, chloroform and ethyl acetate for analysis by NMR 1H, showed more efficient results than the reference antioxidant Carduus marianus. The classes of organics compounds were determined were phenolics in the fraction of ethyl acetate and terpenes in chloroform and hexane fractions. The ethil acetate fraction had the highest content of flavonoids and increased scavenging capacity of DPPH●, possibly by the presence of phenolic compounds. Therefore, a detailed investigation of the phytochemical composition and in vivo study of the C. impressa hydroethanolic extract is suggested to characterize the active compounds of the species

Germination and mycelial growth of Bipolaris euphorbiae Muchovej & Carvalho as influenced by herbicides and surfactants

Bipolaris euphorbiae Muchovej & Carvalho é um forte candidato para o controle de Euphorbia heterophylla L. (amendoim bravo). Este fungo pode ser aplicado em combinação com herbicidas para controlar um maior espectro de espécies daninhas. Para tanto, experimentos laboratoriais foram realizados para verificar a possibilidade da utilização de mistura de tanque de esporos de B. euphorbiae e herbicidas ou surfatantes recomendados para a cultura da soja. Crescimento micelial e germinação de conídios foram avaliados em meio BDA acrescido dos herbicidas, nas concentrações recomendadas dos produtos comerciais, oxasulfuron (80 g/ha), glifosato (4 L/ha), bentazon (1.5 L/ha), fomesafen (1 L/ha), chlorimuron-ethyl (80 g/ha), lactofen (1 L/ha) e imazetaphyr (1 L/ha) e dos surfatantes Energic (2 ml/L), Aterbane (2,5 ml/L), Silwet L-77Ag (1 ml/L), Herbitensil (2 ml/L) e Natur L'óleo (10 ml/L). Diluições dos herbicidas de 50% e 25% foram avaliadas com um consumo de calda equivalente a 300 L/ha. Os surfatantes foram somente utilizados nas concentrações recomendadas. O crescimento micelial não foi afetado por bentazon e fomesafen e apenas levemente por oxasulfuron. Porém, glifosato, chlorimuron-ethyl, lactofen, Energic, Herbitensil, Silwet, e Aterbane o reduziram drasticamente. A redução observada com imazetaphyr foi intermediária e Natur L' óleo promoveu o crescimento micelial. Na presença dos surfatantes, observou-se que todos permitiram uma porcentagem de germinação equivalente àquela alcançada na presença de água. Energic e Herbitensil causaram um retardamento expressivo. Com Herbitensil, o processo germinativo iniciou somente aos 120 minutos. Com herbicidas, foi observado que somente na presença de glifosato e imazetaphyr a germinação dos conídios não seguiu a tendência observada com água, como ocorreu com os outros produtos testados.

Eficácia de herbicidas aplicados em pós-emergência na cultura da soja convencional e transgênica

Na cultura da soja é frequente o uso de herbicidas seletivos aplicados em pósemergência para o controle das plantas daninhas. Com o objetivo de avaliar a eficiência e a seletividade de herbicidas aplicados em pós-emergência, isolados e em misturas, para o controle de plantas daninhas e os efeitos sobre o crescimento e o desenvolvimento da soja convencional (M-SOY 8001) e transgênica (M-SOY 7908 RR), foram desenvolvidos dois experimentos em campo, nos anos agrícolas 2006/2007 e 2007/2008. Os tratamentos constaram dos herbicidas: lactofen (168 g ha-1), glyphosate (1.080 g ha-1), lactofen + chlorimuronethyl (96 + 10g ha-1), chlorimuron-ethyl + imazethapyr (10 + 70 g ha-1), chlorimuron-ethyl + bentazon (10 + 600 g ha-1), glyphosate + imazethapyr (900 + 70 g ha-1), lactofen + chlorimuronethyl + imazethapyr (96 + 10 + 70 g ha-1) e lactofen + chlorimuron-ethyl + imazethapyr/ haloxyfop-methyl (96 + 10 + 70 + 60 g ha-1). Além disso, mantiveram-se duas testemunhas sem aplicação de herbicida (capinada e sem capina). O delineamento experimental utilizado foi em blocos ao acaso, com quatro repetições. O herbicida lactofen aplicado isoladamente e em mistura com chlorimuron-etyl, imazethapyr e haloxyfop-methyl provocou intoxicação inicial às plantas de soja, porém aos 27 dias após aplicação a cultura apresentava-se recuperada. No primeiro ano agrícola, as plantas daninhas foram satisfatoriamente controladas pelos tratamentos químicos. No segundo ano, os tratamentos que resultaram em melhor controle das infestantes foram glyphosate e glyphosate + imazethapyr. Houve redução na altura final das plantas, no segundo ano, tratadas com chlorimuron-ethyl + imazethapyr, lactofen + chlorimuron-ethyl + imazethapyr e lactofen + chlorimuron-ethyl + imazethapyr/haloxyfopmethyl. Foi constatada redução na produtividade de grãos da variedade M-SOY 7908 RR tratada com lactofen e com a mistura chlorimuron ethyl + bentazon no primeiro ano. A aplicação de chlorimuron-ethyl + bentazon proporcionou redução na produtividade da variedade M-SOY 8001 no segundo ano.

Biodiesel etílico filtrado de óleo residual de soja: desempenho de um trator agrícola na operação de gradagem

Filtered ethyl ester biodiesel from residual soybean oil: performance of an agricultural tractor in the disk harrow operation. This test was conducted to evaluate the performance of an agricultural tractor using a mixture of biodiesel and petroleum diesel. The experiment was conducted at FCAV-Unesp, Jaboticabal, using a 4x2 AFWD tractor with 73.6 kW (100 hp @ 2,300 rpm) of power in the motor, pulling a disk harrow. The biodiesel used was of the ethyl type, filtered, and produced from residual soybean oil. The experimental design was completed randomized in factorial scheme (4x5), with 20 treatments and 4 repetitions, in which 5 ratios of biodiesel and petroleum diesel mixtures were combined (0 and 100%, 25 and 75%, 50 and 50%, 75 and 25% and 100 and 0%), with 4 displacement runs. The analyzed variables were traction bar power, engine rotation and displacement speed. The results evidenced that the mixture ratio (biodiesel and petroleum diesel) did not compromise tractor performance until the limit of 50%.

Seletividade de herbicidas, aplicados em pós-emergência, às plantas de alfafa

Foram conduzidos doi experimentos na UNESP/Jaboticabal, em casa-de-vegetação, com o objetivo de avaliar-se a toxicidade de diferentes herbicidas, aplicados em pós-emergênica, às plantas de alfafa. No primeiro, utilizou-se de um delineamento experimental com parcelas inteiramente casualizadas para avaliar-se os efeitos fitotóxicos dos seguintes herbicidas: MSMA, clethodim + óleo mineral, lactofen, fluazifop-pbutil, fomesafen + óleo mineral haloxyfop-methyl + óleo mineral, fenoxaprop-ethyl, chlorimuronethyl, halosulfuron + óleo mineral, nicosulfuron, acifluorfen, imazethapyr, bentazon + óleo mineral e cyanazine + simazine, todos em só dose. Foram feitas avaliações da fitotoxicidade por meio de notas, atribuídas visualmente, em função dos sintomas constatados nas plantas. A altura das plantas e o peso da matéria seca da parte área foram avaliadas no período de desenvolvimento inicial e após a primeira rebrota. No segundo experimento foi seguido mesmo esquema de instalação e condução do anterior, após escolherse os herbicidas e doses, sendo eles, o MSMA, chlorimuron-ethyl, imazethapyr, bentazon + óleo mineral, clethodim, clethodim + óleo mineral e bentazon + MSMA. Os herbicidas mais seletivos às plantas de alfafa foram haloxyfop-methyl, fluazifop-p-butil, fenoxaprop-ethyl, MSMA, imazethapyr, bentazon e clethodim isolado e adicionado de óleo mineral).

Manejo químico de plantas adultas de Digitaria insularis com glyphosate isolado e em mistura com chlorimuronethyl ou quizalofop-p-tefuril em área de plantio direto

O objetivo deste trabalho foi avaliar a eficácia do herbicida glyphosate, isolado e em mistura com chlorimuron-ethyl ou quizalofop-p-tefuril, e o efeito da adição de óleo mineral à calda de glyphosate e chlorimuron-ethy no controle de plantas adultas de Digitaria insularis, em área sob sistema de plantio direto. Foram desenvolvidos dois experimentos, em condições de campo, um de novembro de 2005 a fevereiro de 2006 e outro de novembro de 2006 a janeiro de 2007, em Jaboticabal (SP). O delineamento experimental foi o de blocos ao acaso, em esquema fatorial, com quatro repetições. No primeiro experimento, foram avaliadas oito combinações (Fator A) entre o glyphosate (0,72; 1,44; 2,16 e 2,88 kg ha-1) e o chlorimuron-ethyl (0 e 10 g ha-1), três doses (Fator B) de óleo mineral (0; 0,5 e 1,0 L ha-1) e uma testemunha mantida infestada sem a aplicação de herbicida. No segundo, foram estudadas seis associações (Fator A) entre o glyphosate (1,44; 2,16 e 2,88 kg ha-1) e o quizalofop-p-tefuril (0 e 120 g ha-1) e um tratamento de quizalofop-p-tefuril (120 g ha-1) isolado, combinados com aplicações sequenciais (Fator B) de glyphosate (0; 0,72 e 1,44 kg ha-1), pulverizado 15 dias após a primeira a aplicação, além de uma testemunha infestada sem a aplicação de herbicida. Nas avaliações iniciais, no experimento de 2005/ 2006, em plantas pulverizadas com as maiores doses de glyphosate, isolado ou em mistura ao chlorimuron, havia injúrias visuais severas, com classificação do controle de bom (71% a 80%) a muito bom (81% a 90%). Com o decorrer do tempo, as plantas rebrotaram revelando seu potencial de recuperação e a ineficácia dos herbicidas no controle definitivo desta espécie. A adição de óleo mineral à calda de glyphosate e chlorimuron não contribuiu para o controle de D. insularis. No outro experimento, o quizalofop isolado e a sua associação ao glyphosate, combinados à aplicação sequencial de 1,44 kg ha-1 de glyphosate, resultaram em melhor controle da planta daninha.