Unsteady transition in an axial-flow turbine. Part 1. Measurements on the turbine rotor

Previously published measurements in a low-speed, single-stage, axial-flow turbine have been reanalyzed in the light of more recent understanding. The measurements include time-resolved hot-wire traverses and surface hot film gage measurements at the midspan of the rotor suction surface with three different rotor-stator spacings. This paper investigates the suction surface boundary layer transition process, using surface-distance time plots and boundary layer cross sections to demonstrate the unsteady and two-dimensional nature of the process.

Stall inception in axial compressors

Detailed measurements have been made of the transient stalling process in an axial compressor stage. The stage is of high hub-casing ratio and stall is initiated in the rotor. If the rotor tip clearance is small stall inception occurs at the hub, but at clearances typical for a multistage compressor the inception is at the tip. The crucial quantity in both cases is the blockage caused by the endwall boundary layer. Prior to stall, disturbances rotate around the inlet flow in sympathy with rotating variations in the endwall blockage.

Stability of flow through multistage axial compressors

This paper describes measurements of the performance of a research stage operating in isolation and as part of a multistage compressor. It is shown that the stall point and the stalled performance of the stage are properties of the system in which it operates rather than a property of the stage itself. The consequences of this for the estimation of the stall point for compressors and compression systems are discussed. The support that the measurements give to assumptions made by mathematical models which use the concept of an 'underlying axisymmetric' characteristic, are highlighted.

Length-weight relationship in the Asian seabass, Lates calcarifer (Bloch) under culture condition

Asian seabass, Lates calcarifer (Bloch) - a catadromous centropomid perch, is a good candidate species for brackishwater aquaculture in India. The length-weight relationship and the relative condition of L. calcarifer were assessed under culture condition. The length of the fish samples ranged from 25 to 240 mm and the relative condition (w sub(r)) of the fish for different length groups ranged from 99.54 to 104.39, indicating the good condition of the fish. The regression analysis of log-transformed length-weight data was carried out and the 'b' coefficient indicates the good condition of fish showing an isometric growth in the juvenile phase under culture condition.

Length-weight studies of Epinephelus chlorostigma and E. areolatus from Arabian Gulf

Regression coefficient value (b) of the length-weight relation of Epinephelus chlorostigma was registered as 2.6383, which is significantly (p<0.01) less than the hypothetical value (3). This coefficient of E. areolatus was registered as 2.9500, a value close to 3. The correlation coefficients (r) were registered as 0.9725 and 0.9837 for E. chlorostigma and E. areolatus, respectively, which show a good relationship between the two parameters.

Studies on length-weight relationship of Gerres filamentosus Cuvier from the estuaries of the southern Karnataka coast

Random samples of Gerres filamentosus Cuvier from the Netravathi-Gurpur, Mulky, Kallayanapura, Mabukala and Kundapura estuaries of the southern Karnataka Coast were collected in the years 2000, 2001 and 2002, and length-weight relationships for each estuary were derived using multiple linear regression technique with one dummy variable. Hence, combined or sex-wise length-weight relationships were obtained after testing for homogeneity and isometric growth condition of fishes for each estuary by t-test. The extent of closeness of length-weight relationships between sexes and among estuaries for different years is explained by a trend line graph. The whole process of multiple linear regression analysis with one dummy variable is a better substitute for the analysis of covariance technique.

Effect of blade tip geometry on the tip leakage flow in axial turbine cascades

The phenomenon of tip leakage has been studied in two linear cascades of turbine blades. The investigation includes an examination of the performance of the cascades with a variety of tip geometries. The effects of using plain tips, suction side squealers, and pressure side squealers are reported. Traverses of the exit flow field were made in order to determine the overall performance. A method of calculating the tip discharge coefficients for squealer geometries is put forward. In linking the tip discharge coefficient and cascade losses, a procedure for predicting the relative performance of tip geometries is developed. The model is used to examine the results obtained using the different tip treatments and to highlight the important aspects of the loss generation process.

Three-dimensional interactions in the rotor of an axial turbine

This article presents a study of the development of the three-dimensional flowfield within the rotor blades of a low-speed, large-scale axial flow turbine. Measurements have been performed in the rotating and stationary frames of reference. Time-mean data have been obtained using miniature five-hole pneumatic probes, whereas the unsteady development of the flow has been determined using three-axis subminiature hot-wire anemometers. Additional information is provided by the results of blade-surface flow-visualization experiments and surface-mounted hot-film anemometers. The development of the stator exit flow, as it passes through the rotor blades, is described. Unsteady data suggest that the presence of the rotor secondary and tip leakage flows restricts the region of unsteady interaction to near midspan when the stator wakes and secondary flows are adjacent to the suction surface. Surface-mounted hot-film data show that this affects the suction-side laminar-turbulent transition process.

Distribution and length-weight relationship of tunas and tuna-like fishes around Ceylon

Tunas and tuna-like fishes have contributed considerably towards the increase in fish production from Ceylon's coastal waters, during the last five years and in this blood fish group lies a potential resource for a further increase in production. Consequently considerable attention is being paid to the study of these species. Length frequency sampling of these species are being carried out and quite often it becomes necessary to convert catch in terms of weight to catch in terms of number, when estimating apparent abundance of the stock. The length-weight relationship in addition to its usefulness in converting length frequency data to weight frequency data for such purpose is of general value to biologists and even to fishermen. The six species studied are yellowfin tuna (Thunnus alacares, Bonneterre), skipjack tuna (Katsuwonus pelamis, Linnaeus), mackerel tuna (Buthynnus affinis, Cantor), frigate mackerel (narrow corseleted Auxis thazard, Lacepede and broad corseleted A. rochie, Risso) and bonito (Saida orientalis, T&S).

Wadge Bank trawl fishery studies. Pt. 4. An analysis of the length frequency measurements of the sea bream (Lethrinus nebulosus) made in 1949 and 1953 to 1958

Length frequency distributions of the sea bream collected during the period 1953 to 1958 have been analysed. The increase in average sizes of the sea bream with depth suggests a movement to deeper waters with increase in size. By numbers, the sea bream is more abundant between 21 and 30 fathoms than in deeper areas. The recruitment was continuous and regular. There is no sign of entry or progression of a dominant brood throughout the period under study. Length frequency distribution shows three distinct modes. The first mode occurs regularly but does not progress beyond 40cm, recruitment being balanced by natural and fishing mortality. The other two which are not regular are probably the result of fishing outside regular areas. Short sections of “growth” lines which fit into one another when extrapolated, are evident. The larger lines obtained by extrapolation are parallel to one another. These tentative "growth lines" indicate that this species which enters the fishing grounds, when 15 cm or larger in length are exploited by the trawl fishery for a period of three to four years. This species appears to be six months old when it enters the fishing grounds and increases in length by about 37.5 cm in the next 30 months. Later growth slows down. The average size of the specimens sampled continued to get smaller from 1953 till 1957. It is shown that this reduction in size is due to increased fishing effort.

Axial and journal bearings for superconducting flywheel systems

Axial and journal bearings have been investigated for use in superconducting flywheel systems. Our test rig comprises of an Evershed type magnetic bearing used to levitate a 35 kg rotor. The stabilizing forces are provided by superconducting axial and journal bearings. In this study we focus on the vertical stiffness measurements and explore the use of journal bearings. The journal bearing consists of radial magnets with alternating polarities. Our results indicate that this type of journal bearing can effectively stabilize the rotor. Spin-down test shows a linear behavior.

An improved technique to measure axial variation in wall flow along the channels of a diesel particulate filter

A technique to measure wall flow variation in Diesel Particle Filters (DPFs) is described. In a recent paper, it was shown how the flow distribution in DPFs could be measured in a non-destructive manner. This involved measuring the progressive dilution of a tracer gas introduced at the "outlet" channel upstream end. In the present paper, a significant further improvement to this technique is described, in which only a single probe is required, rather than the two of the previous technique. The single, traversable, probe consists of a controllable flow sink, and slightly downstream, a tracer gas supply. By controlling the sink flow rate such that a very small concentration of tracer gas is aspirated into it, the total flow up to that location in the channel is determined. Typical results showing the axial variation in the wall flow for known wall blockage cases are presented. It is suggested that this technique could be used to interpret the soot loading in the filter channels in a non-intrusive way.

Axial compressor response to inlet flow distortions by a CFD analysis

The usual approach to compressor design considers uniform inlet flow characteristics. Especially in aircraft applications, the inlet flow is quite often non uniform, and this can result in severe performance degradation. The magnitude of this phenomenon is amplified in military engines due to the complexity of inlet duct configurations and the extreme flight conditions. CFD simulation is an innovative and powerful tool for studying inlet distortions and can bring this inside the very early phases of the design process. This project attempts to study the effects of inlet flow distortions in an axial flow compressor trying to minimize the use computer resources and computational time. The first stage of a low bypass ratio compressor has been analyzed and its clean and distorted performance compared outlining the principal changes due to uneven flow distribution: drop in mass flow, increase in pressure and temperature ratios, decrease in surge margin. Three different studies have then been conducted to better understand the effects of the level, the type and the frequency of the distortion.

Axial stiffness of journal bearings in zero-field and field-cooled modes

Superconducting journal bearings have been investigated for use in flywheel systems. We report on the zero-field cooled and field-cooled stiffness of these bearings. They are made up of radial magnet rings with alternating polarities, a pole pitch of 11 mm and a surface field of 0.1 T. Field-cooled stiffness of the journal bearings increased four times over the zero-field-cooled stiffness. © 2005 IEEE.

Use of length-weight relationship in grading processed beche-de-mer

Holothurians, belonging to the species Holothuria scabra, have been collected by diver-fishermen and processed for export. There is an active fishery for these animals in Palk Bay and Gulf of Mannar, off the north-western coast of Sri Lanka. The absence of standardized method of grading has led to unwarranted variation in sale prices and sometimes in loss of foreign exchange in Sri Lanka. In this paper an attempt is made to present a method to grade processed beche-de-mer by using the lenght-weight relationship.