An algebraic algorithm for the design and analysis of linear dynamical systems

In an earlier paper [1], it has been shown that velocity ratio, defined with reference to the analogous circuit, is a basic parameter in the complete analysis of a linear one-dimensional dynamical system. In this paper it is shown that the terms constituting velocity ratio can be readily determined by means of an algebraic algorithm developed from a heuristic study of the process of transfer matrix multiplication. The algorithm permits the set of most significant terms at a particular frequency of interest to be identified from a knowledge of the relative magnitudes of the impedances of the constituent elements of a proposed configuration. This feature makes the algorithm a potential tool in a first approach to a rational design of a complex dynamical filter. This algorithm is particularly suited for the desk analysis of a medium size system with lumped as well as distributed elements.

Protection of a Static Frequency Converter fed traction network, a case study

Aurizon, Australia's largest rail freight operator, is introducing the Static Frequency Converter (SFC) technology into its electric railway network as part of the Bauhinia Electrification Project. The introduction of SFCs has significant implications on the protection systems of the 50kV traction network. The traditional distance protection calculation method does not work in this configuration because of the effect that the SFC in combination with the remote grid has on the apparent impedance, and was substantially reviewed. The standard overcurrent (OC) protection scheme is not suitable due to the minimum fault level being below the maximum load level and was revised to incorporate directionality and under-voltage inhibit. Delta protection was reviewed to improve sensitivity. A new protection function was introduced to prevent back-feeding faults in the transmission network through the grid connection. Protection inter-tripping was included to ensure selectivity between the SFC protection and the system downstream.

Physiological basis of yield variation in response to row spacing and plant density of mungbean grown in subtropical environments

In this study, we investigated the extent and physiological bases of yield variation due to row spacing and plant density configuration in the mungbean Vigna radiata (L.) Wilczek variety “Crystal” grown in different subtropical environments. Field trials were conducted in six production environments; one rain-fed and one irrigated trial each at Biloela and Emerald, and one rain-fed trial each at Hermitage and Kingaroy sites in Queensland, Australia. In each trial, six combinations of spatial arrangement of plants, achieved through two inter-row spacings of 1 m or 0.9 m (wide row), 0.5 m or 0.3 m (narrow row), with three plant densities, 20, 30 and 40 plants/m2, were compared. The narrow row spacing resulted in 22% higher shoot dry matter and 14% more yield compared to the wide rows. The yield advantage of narrow rows ranged from 10% to 36% in the two irrigated and three rain-fed trials. However, yield loss of up to 10% was also recorded from narrow rows at Emerald where the crop suffered severe drought. Neither the effects of plant density, nor the interaction between plant density and row spacing, however, were significant in any trial. The yield advantage of narrow rows was related to 22% more intercepted radiation. In addition, simulations by the Agricultural Production Systems Simulator model, using site-specific agronomy, soil and weather information, suggested that narrow rows had proportionately greater use of soil water through transpiration, compared to evaporation resulting in higher yield per mm of soil water. The long-term simulation of yield probabilities over 123 years for the two row configurations showed that the mungbean crop planted in narrow rows could produce up to 30% higher grain yield compared to wide rows in 95% of the seasons.

Effect of electric arc discharge on hypersonic blunt body drag

Experimental results on the effect of energy deposition using an electric arc discharge, upstream of a 60° half angle blunt cone configuration in a hypersonic flow is reported.Investigations involving drag measurements and high speed schlieren flow visualization have been carried out in hypersonic shock tunnel using air and argon as the test gases; and an unsteady drag reduction of about 50% (maximum reduction) has been observed in the energy deposition experiments done in argon environment. These studies also show that the effect of discharge on the flow field is more pronounced in argon environment as compared to air, which confirms that thermal effects are mainly responsible for flow alteration in presence of the discharge.

Shock tunnel testing of a Mach 6 hypersonic waverider

A waverider is a lifting body configuration whose upper surface is parallel to the free stream, and the lower surface aerodynamically so designed, that the resulting shock at the design Mach number, is always attached with the leading edge of the vehicle. This prevents spillage from high pressure (lower) surface to the low pressure (upper) surface.In the present study a conical waverider has been designed, fabricated and tested at Mach 6 in the IISc hypersonic shock tunnel HST2. The measurements show that the waverider has a lift to drag ratio of 4.28 at the designed Mach number. Exhaustive FEM and CFD studies are also carried out to complement the force measurements in the tunnel.

Computational Techniques for Haplotype Inference and for Local Alignment Significance

This thesis which consists of an introduction and four peer-reviewed original publications studies the problems of haplotype inference (haplotyping) and local alignment significance. The problems studied here belong to the broad area of bioinformatics and computational biology. The presented solutions are computationally fast and accurate, which makes them practical in high-throughput sequence data analysis. Haplotype inference is a computational problem where the goal is to estimate haplotypes from a sample of genotypes as accurately as possible. This problem is important as the direct measurement of haplotypes is difficult, whereas the genotypes are easier to quantify. Haplotypes are the key-players when studying for example the genetic causes of diseases. In this thesis, three methods are presented for the haplotype inference problem referred to as HaploParser, HIT, and BACH. HaploParser is based on a combinatorial mosaic model and hierarchical parsing that together mimic recombinations and point-mutations in a biologically plausible way. In this mosaic model, the current population is assumed to be evolved from a small founder population. Thus, the haplotypes of the current population are recombinations of the (implicit) founder haplotypes with some point--mutations. HIT (Haplotype Inference Technique) uses a hidden Markov model for haplotypes and efficient algorithms are presented to learn this model from genotype data. The model structure of HIT is analogous to the mosaic model of HaploParser with founder haplotypes. Therefore, it can be seen as a probabilistic model of recombinations and point-mutations. BACH (Bayesian Context-based Haplotyping) utilizes a context tree weighting algorithm to efficiently sum over all variable-length Markov chains to evaluate the posterior probability of a haplotype configuration. Algorithms are presented that find haplotype configurations with high posterior probability. BACH is the most accurate method presented in this thesis and has comparable performance to the best available software for haplotype inference. Local alignment significance is a computational problem where one is interested in whether the local similarities in two sequences are due to the fact that the sequences are related or just by chance. Similarity of sequences is measured by their best local alignment score and from that, a p-value is computed. This p-value is the probability of picking two sequences from the null model that have as good or better best local alignment score. Local alignment significance is used routinely for example in homology searches. In this thesis, a general framework is sketched that allows one to compute a tight upper bound for the p-value of a local pairwise alignment score. Unlike the previous methods, the presented framework is not affeced by so-called edge-effects and can handle gaps (deletions and insertions) without troublesome sampling and curve fitting.

Experimental networking of microcomputers and a minicomputer

The objective of this paper is to discuss some hardware and software features of an experimental network of 8080 and 8085 microcomputers named Micronet. The interprocessor communication in the ring network is established using ring interfaces consisting of universal synchronous-asynchronous receivers-transmitters (USARTs). Another aspect considered is the interfacing of an 8080 microcomputer to a PDP-11/35 minicomputer and the development of the software for the microcomputer-minicomputer link which has been established over a serial line using the USART interface of the microcomputer and the DZ11 module of the minicomputer. This is useful in developing a host-satellite configuration of microcomputers and the minicomputer.

Studies on Unsteady Shock Interactions Near a Generic Scramjet Inlet

An experimental and numerical study is presented to show the effect of cowl length and angle on the ramp/cowl shock interaction phenomena fora two-dimensional planar scramjet inlet model. Experiments areconducted in a hypersonic shock tunnel, at Mach 8, at four lengths of owl and three cowl angles. Investigations include schlieren flow Visualization near the cowl region and static pressure and heat transfer rate measurement inside the inlet chamber. Various ramp/cowl shock interaction processes resulted for different cowl configurations have been visualized using a high-speed camera. Edney type-II interference pattern is observed for 131 and 141-mm cowl lengths,whereas it is an Edney type-I interference pattern in case of a 151 mm cowl with all their typical features resulting because of the ramp/cowl shock interaction. Experiments with a cowl configuration other than 0deg show the flow to he established through the inlet because or the reduced contraction ratio. Heat transfer peaks can be observed for the10 and 20-deg cowl cases where flow through the inlet is found to be established. These may serve as the possible locations of fuel injection.

Multistage monostable multivibrator using load-coupled regenerative feedback

A monostable multivibrator configuration using a new technique of regenerative feedback is discussed. This circuit provides an elegant alternative in situations wherein several monostable multivibrators have to be connected in tandem.

Quantification of the inevitable: the influence of soil macrofauna on soil water movement in rehabilitated open-cut mined lands

Recolonisation of soil by macrofauna (especially ants, termites and earthworms) in rehabilitated open-cut mine sites is inevitable and, in terms of habitat restoration and function, typically of great value. In these highly disturbed landscapes, soil invertebrates play a major role in soil development (macropore configuration, nutrient cycling, bioturbation, etc.) and can influence hydrological processes such as infiltration, seepage, runoff generation and soil erosion. Understanding and quantifying these ecosystem processes is important in rehabilitation design, establishment and subsequent management to ensure progress to the desired end goal, especially in waste cover systems designed to prevent water reaching and transporting underlying hazardous waste materials. However, the soil macrofauna is typically overlooked during hydrological modelling, possibly due to uncertainties on the extent of their influence, which can lead to failure of waste cover systems or rehabilitation activities. We propose that scientific experiments under controlled conditions and field trials on post-mining lands are required to quantify (i) macrofauna–soil structure interactions, (ii) functional dynamics of macrofauna taxa,and (iii) their effects on macrofauna and soil development over time. Such knowledge would provide crucial information for soil water models, which would increase confidence in mine waste cover design recommendations and eventually lead to higher likelihood of rehabilitation success of open-cut mining land.

Structure and Conformation of a Cyclic Tripeptide

MANY cyclic peptides have interesting biological functions and the details of their molecular structure and conformation have been the subject of extensive investigations. Cyclic dipeptides such as diketopiperazine have been synthesised and shown to occur with the peptide units in the cis configuration1,2. In the case of a tripeptide, cyclisation can take place only if all three units are in the cis configuration3. In cyclic peptides with four units also, cis peptides are found4,5. As the number of the peptide units increases, the more stable trans configuration is generally more common6,7. We report here the main results of our X-ray crystallographic investigations of the cyclic tripeptides L-Pro-L-Pro-L-Pro and L-Pro-L-Pro-L-Hyp (hereafter called CTP 1 and CTP 2, respectively). CTP 1 was synthesised by Rothe et al. 8 and its derivatives have been prepared by Blout and his collaborators9.

Lithium nuclear-magnetic-resonance in lithium acetate dihydrate, Li(CH3COO).2H2O

Li n.m.r, in single crystals of lithium acetate dihydrate is used to determine the quadrupole coupling parameters: (e2qQ/h) and r/. The orientations of the principal z, y and x components of the electric field gradient tensor are determined to be along the crystallographic b, a and c axes respectively. The parameters experimentally determined are (e2qQ/h)= 154"6 kHz; and i/= 0.9. This study indicates a tetrahedral configuration around the Li ion, confirming the recent X-ray and p.m.r, results.

Tila tilassa : Liturgian ja tilan dialogi alttarin äärellä

This study examines the organisation and transformation of altar space in the modern Evangelical Lutheran Church of Finland in liturgical and architectural perspective. The research data consists of 65 altar spaces in The Finnish Evangelical Lutheran church buildings. All of these were characterised in Church Government records as churches , built 1962 1999 and had been consecrated. The main data was collected by means of observation, photographing, and drawing sketches of altar spaces. The focus of this study concerns the organisation of modern Finnish Evangelical Lutheran altar spaces and, in particular, their changes also in relation to the liturgical movement. The challenge of this approach was especially in discovering the spatial identity of an altar space in terms of unequivocal boundaries. The analysis was realised in three stages. Interiors, the organisation of altar space, as well as architectonic qualities of altar spaces in terms of floor elevations, shapes of ceilings, lighting, and openings in the altar space were analysed. Moreover, attention was focused on furnishing and fixed versus movable pieces of furniture (such as the altar, altar rail, the pulpit, the baptismal font, and lectern). Finally, the potential qualitative and quantitative changes in altar space were examined. All in all, the majority of churches in the data featured elongated church halls with an altar at the end of the nave. To look at the data in chronological perspective, increasingly wide church halls had been built since the 1980s (yet there was only one central hall in which the altar was placed at the middle point of the church). Every third church altar was movable. As for the focal point of this study and the altar in particular, it was my aim to pay attention to the versus populum altar and its development in relation to the (Lutheran) liturgy. Hence, it was meaningful to determine, in terms of interior design, whether liturgists were able to celebrate facing the people attending the service. In the 1960s and 70s, a versus orientem altar featured in more than half of all new Finnish Lutheran churches, yet in 2000 two out of three churches featured a versus populum altar. For architectural and esthetic reasons (and not primarily due to liturgical ideas), also altars standing freely off the walls had been constructed. In terms of the liturgy, versus populum altars had been realised in expectation of increased communication between liturgist and worshippers. However, the analysis indicated that the altar could also become a divider of space. This aspect is a novel finding in relation to earlier and concurrent discussions concerning the liturgical movement. This study concluded, all in all, that altars had been increasingly constructed closer and closer to the worshiping parish and, accordingly, used increasingly often in the versus populum manner. Lecterns were often movable until the millennium this was the case in most altar spaces. Baptismal fonts did not have a permanent place in this data, and the data even included altar spaces with no baptismal fonts in the choir, nor the church hall. The position and status of fonts was generally weakened even if baptism in the Lutheran Church was regarded as one of the two sacraments together with the eucharist. The study concluded that even if baptism is regarded as a sacrament in the church, the position and status of baptismal fonts had weakened overall in newer church architecture. In other words, the tendency of the liturgical movement to emphasise the service and its celebration had obviously had its effect on the placement of baptismal fonts in the church hall. This research indicated that the pieces of furniture that mostly involved (many kinds of) visual and spatial changes included the altar and the lectern. In certain instances, fixed furnishings had been substituted by movable pieces or, moreover, new pieces of furniture and paraphernalia such as music instruments, pieces of art, tables, chairs and plants were brought in. In the Evangelical Lutheran Church of Finland, liturgical changes were principally inspired by the Catholic Church, in which liturgical changes are essentially based on Canon Law. Unlike Finnish Lutheranism, Catholicism provides detailed rules and principles even regarding the design of an altar space. According to this study, in the Finnish Lutheran Church, the primarily functional nature of given guidelines and instructions characterises several practical solutions in furnishing.

Hydrolysis of sphingomyelin to ceramide with hydrofluoric acid

Sphingomyelin was hydrolyzed to ceramide near quantitatively on treatment with 40% HF at 40°C for 72 hr. The reaction of sphingomyelin with HF is much slower than phosphoglycerides. HF treatment did not alter either the fatty acid composition or the stereochemical configuration of the sphingosine moiety of ceramide formed.

(v, k, λ) Configurations and self-dual codes

The incidence matrix of a (v, k, λ) configuration is used to construct a (2v, v) and a (2v + 2, v + 1) self-dual code. If the incidence matrix is a circulant, the codes obtained are quasi-cyclic and extended quasi-cyclic, respectively. The weight distributions of some codes of this type are obtained.