Analysis of the moisture effect on the mechanical behaviour of an adhesively bonded joint under proportional multi-axial loads

The objective of the study is to identify the 3D behaviour of an adhesive in an assembly, and to take into account the effect of ageing in a marine environment. To that end, three different tests were employed. Gravimetric analyses were used to determine the water diffusion kinetics in the adhesive. Bulk tensile tests were performed to highlight the effects of humid ageing on the adhesive behaviour. Modified Arcan tests were performed for several ageing times to obtain the experimental database which was necessary to identify constitutive models. A Mahnken-Schlimmer type model was determined for the unaged state according to a procedure developed in a previous study. This identification used inverse techniques. It was based on the unaged modified Arcan results and on a coupling between an optimisation routine and finite-element analysis. Then, a global inverse identification procedure was developed. Its aim was to relate the unaged parameters to the moisture concentration and overcome the difficulties usually associated with ageing of bonded assemblies in a humid environment: a non-uniformity of the stress state and a gradient of mechanical properties in the adhesive. This procedure was similar to the one used in the first part but needed modified Arcan results for several ageing times. It also required an initial assumption for the evolution of the Mahnken-Schlimmer parameters with the moisture concentration.

THE ROLE OF THE MECHANICAL ENVIRONMENT ON CANCER CELL TRANSMIGRATION AND MRNA LOCALIZATION

Most cancer-related deaths are due to metastasis formation, the ability of cancer cells to break away from the primary tumor site, transmigrate through the endothelium, and form secondary tumors in distant areas. Many studies have identified links between the mechanical properties of the cellular microenvironment and the behavior of cancer cells. Cells may experience heterogeneous microenvironments of varying stiffness during tumor progression, transmigration, and invasion into the basement membrane. In addition to mechanical factors, the localization of RNAs to lamellipodial regions has been proposed to play an important part in metastasis. This dissertation provides a quantitative evaluation of the biophysical effects on cancer cell transmigration and RNA localization. In the first part of this dissertation, we sought to compare cancer cell and leukocyte transmigration and investigate the impact of matrix stiffness on transmigration process. We found that cancer cell transmigration includes an additional step, ‘incorporation’, into the endothelial cell (EC) monolayer. During this phase, cancer cells physically displace ECs and spread into the monolayer. Furthermore, the effects of subendothelial matrix stiffness and endothelial activation on cancer cell incorporation are cell-specific, a notable difference from the process by which leukocytes transmigrate. Collectively, our results provide mechanistic insights into tumor cell extravasation and demonstrate that incorporation into the endothelium is one of the earliest steps. In the next part of this work, we investigated how matrix stiffness impacts RNA localization and its relevance to cancer metastasis. In migrating cells, the tumor suppressor protein, adenomatous polyposis coli (APC) targets RNAs to cellular protrusions. We observed that increasing stiffness promotes the peripheral localization of these APC-dependent RNAs and that cellular contractility plays a role in regulating this pathway. We next investigated the mechanism underlying the effect of substrate stiffness and cellular contractility. We found that contractility drives localization of RNAs to protrusions through modulation of detyrosinated microtubules, a network of modified microtubules that associate with, and are required for localization of APC-dependent RNAs. These results raise the possibility that as the matrix environment becomes stiffer during tumor progression, it promotes the localization of RNAs and ultimately induces a metastatic phenotype.

Simulação em uso dos pisos de madeira de Eucalyptus sp e Corymbia maculata

A caracterização anatômica, física, mecânica e química da madeira fornece informações importantes para sua melhor utilização. Contudo, para que madeiras se tornem boa opção para o mercado de pisos, adicionalmente é necessária a realização de ensaios que simulem suas reais condições em serviço. Esses ensaios simulam o pisoteio executado pelos sapatos de salto com pequenas áreas de pressão, o arraste e a queda de objetos, a resistência à abrasão da superfície e o atrito oferecido durante o deslocamento de pessoas que caminham sobre ele. Grande dificuldade da seleção de novas madeiras para pisos está na ausência de valores de referência físico-mecânicos. O presente trabalho visou a caracterizar as madeiras de Eucalyptus clöeziana F. Muell, de Eucalyptus microcorys F. Muell e de Corymbia maculata Hook, para as propriedades de densidade básica, retratibilidade, aplicação de carga rolante, de atrito estático e dinâmico, endentação causada por cargas aplicadas em pequenas áreas, impacto da esfera de aço cadente e resistência à abrasão. Foi observado que as madeiras estudadas podem ser utilizadas para a confecção de pisos, de acordo com seus resultados obtidos e por meio de comparações com resultados de literatura.

Dielectric properties of thermosetting material nanocomposites

The dieletric relaxation properties of thermosetting material nanocomposites based on spherosilicate nanoplatforms were studied from room temperature to 170 degrees C, varying the frequency from 10 to 1000 KHz. Permittivity (epsilon'), dielectric loss (epsilon ''), and activation energy (E-a) were calculated. The results of dielectric relaxation were confirmed by those of the final properties. The dielectric loss amplitude decreases with increasing ODPG content until about 70-73 wt % and slightly increases at higher ODPG content. This means that the increasing of the ODPG content in the composite samples decreases the number of pendants groups and/or increases crosslink densitv, causing decreased motion of organic tethers, and subsequently decreasing of the dipolar mobility. The results of apparent activation energy, fracture toughness and tensile modulus mechanical properties show the same profile with respect to ODPG content, in the sense that they exhibit maxima around 70 wt % ODPG. For the ODPG/MDA composites, this formulation of 70 wt % ODPG containing excess of amine is not composition where the highest crosslinked density is reached. This implies that the best mechanical properties and E-a are provided by some degree of chain flexibility. (c) 2007 Wiley Periodicals, Inc.

Comb-like acrylic-based polymer latexes containing nano-sized crystalline or liquid crystalline domains

306 p.

Design, Fabrication, and Mechanical Property Analysis of 3D Nanoarchitected Materials

Recent developments in micro- and nanoscale 3D fabrication techniques have enabled the creation of materials with a controllable nanoarchitecture that can have structural features spanning 5 orders of magnitude from tens of nanometers to millimeters. These fabrication methods in conjunction with nanomaterial processing techniques permit a nearly unbounded design space through which new combinations of nanomaterials and architecture can be realized. In the course of this work, we designed, fabricated, and mechanically analyzed a wide range of nanoarchitected materials in the form of nanolattices made from polymer, composite, and hollow ceramic beams. Using a combination of two-photon lithography and atomic layer deposition, we fabricated samples with periodic and hierarchical architectures spanning densities over 4 orders of magnitude from ρ=0.3-300kg/m³ and with features as small as 5nm. Uniaxial compression and cyclic loading tests performed on different nanolattice topologies revealed a range of novel mechanical properties: the constituent nanoceramics used here have size-enhanced strengths that approach the theoretical limit of materials strength; hollow aluminum oxide (Al₂O₃) nanolattices exhibited ductile-like deformation and recovered nearly completely after compression to 50% strain when their wall thicknesses were reduced below 20nm due to the activation of shell buckling; hierarchical nanolattices exhibited enhanced recoverability and a near linear scaling of strength and stiffness with relative density, with E∝ρ^1.04 and σy∝ρ^1.17 for hollow Al₂O₃ samples; periodic rigid and non-rigid nanolattice topologies were tested and showed a nearly uniform scaling of strength and stiffness with relative density, marking a significant deviation from traditional theories on “bending” and “stretching” dominated cellular solids; and the mechanical behavior across all topologies was highly tunable and was observed to strongly correlate with the slenderness λ and the wall thickness-to-radius ratio t/a of the beams. These results demonstrate the potential of nanoarchitected materials to create new highly tunable mechanical metamaterials with previously unattainable properties.

IN-SITU ELECTRICAL, MECHANICAL AND ELECTROCHEMICAL CHARACTERIZATIONS OF ONE-DIMENSIONAL NANOSTRUCTURES

One-dimensional nanostructures initiated new aspects to the materials applications due to their superior properties compared to the bulk materials. Properties of nanostructures have been characterized by many techniques and used for various device applications. However, simultaneous correlation between the physical and structural properties of these nanomaterials has not been widely investigated. Therefore, it is necessary to perform in-situ study on the physical and structural properties of nanomaterials to understand their relation. In this work, we will use a unique instrument to perform real time atomic force microscopy (AFM) and scanning tunneling microscopy (STM) of nanomaterials inside a transmission electron microscopy (TEM) system. This AFM/STM-TEM system is used to investigate the mechanical, electrical, and electrochemical properties of boron nitride nanotubes (BNNTs) and Silicon nanorods (SiNRs). BNNTs are one of the subjects of this PhD research due to their comparable, and in some cases superior, properties compared to carbon nanotubes. Therefore, to further develop their applications, it is required to investigate these characteristics in atomic level. In this research, the mechanical properties of multi-walled BNNTs were first studied. Several tests were designed to study and characterize their real-time deformation behavior to the applied force. Observations revealed that BNNTs possess highly flexible structures under applied force. Detailed studies were then conducted to understand the bending mechanism of the BNNTs. Formations of reversible ripples were observed and described in terms of thermodynamic energy of the system. Fracture failure of BNNTs were initiated at the outermost walls and characterized to be brittle. Second, the electrical properties of individual BNNTs were studied. Results showed that the bandgap and electronic properties of BNNTs can be engineered by means of applied strain. It was found that the conductivity, electron concentration and carrier mobility of BNNTs can be tuned as a function of applied stress. Although, BNNTs are considered to be candidate for field emission applications, observations revealed that their properties degrade upon cycles of emissions. Results showed that due to the high emission current density, the temperature of the sample was increased and reached to the decomposition temperature at which the B-N bonds start to break. In addition to BNNTs, we have also performed in-situ study on the electrochemical properties of silicon nanorods (SiNRs). Specifically, lithiation and delithiation of SiNRs were studied by our STM-TEM system. Our observations showed the direct formation of Li22Si5 phases as a result of lithium intercalation. Radial expansion of the anode materials were observed and characterized in terms of size-scale. Later, the formation and growth of the lithium fibers on the surface of the anode materials were observed and studied. Results revealed the formation of lithium islands inside the ionic liquid electrolyte which then grew as Li dendrite toward the cathode material.

A comparative study of the structural, mechanical and tribological characteristics of TiSiC-Cr coatings prepared in CH4 and C2H2 reactive atmosphere by cathodic vacuum arc

TiSiC-Cr coatings, with Cr and Si as additional elements, were deposited on Si, C 45 and 316 L steel substrates via cathodic arc evaporation. Two series of coatings with thicknesses in the range of 3.6–3.9 μm were produced, using either CH4 or C2H2 as carbon containing gas. For each series, different coatings were prepared by varying the carbon rich gas flow rate between 90 and 130 sccm, while maintaining constant cathode currents (110 and 100 A at TiSi and Cr cathodes, respectively), substrate bias (–200 V) and substrate temperature (∼320 °C). The coatings were analyzed for their mechanical characteristics (hardness, adhesion) and tribological performance (friction, wear), along with their elemental and phase composition, chemical bonds, crystalline structure and cross-sectional morphology. The coatings were found to be formed with nano-scale composite structures consisting of carbide crystallites (grain size of 3.1–8.2 nm) and amorphous hydrogenated carbon. The experimental results showed significant differences between the two coating series, where the films formed from C2H2 exhibited markedly superior characteristics in terms of microstructure, morphology, hardness, friction behaviour and wear resistance. For the coatings prepared using CH4, the measured values of crystallite size, hardness, friction coefficient and wear rate were in the ranges of 7.2–8.2 nm, 26–30 GPa, 0.3–0.4 and 2.1–4.8 × 10−6 mm3 N−1 m−1, respectively, while for the coatings grown in C2H2, the values of these characteristics were found to be in the ranges of 3.1–3.7 nm, 41–45 GPa, 0.1–0.2 and 1.4–3.0 × 10−6 mm3 N−1 m−1, respectively. Among the investigated coatings, the one produced using C2H2 at the highest flow rate (130 sccm) exhibited the highest hardness (45.1 GPa), the lowest friction coefficient (0.10) and the best wear resistance (wear rate of 1.4 × 10−6 mm3 N−1 m−1).

Utilisation d’arbres de faible vigueur provenant de forêts feuillues tempérées comme matière première pour la fabrication de granules de bois

La présente étude avait pour objectif de contribuer à une meilleure compréhension de la granulation des bois feuillus par l’évaluation de la possibilité technique de transformer des bois feuillus de faible vigueur (l’érable à sucre et le bouleau jaune) en granules conventionnels et granules de haute qualité, un type prometteur de transport énergétique. Trois études individuelles ont été réalisées et présentées dans cette thèse. La première étude visait à déterminer s’il y a des changements de teneur en extractibles, cendres, et lignine du bois entre les classes de vigueur des arbres. Les teneurs plus élevées en extractibles et en lignine dans les arbres peu vigoureux ont suggéré que ces derniers sont plus appropriés par rapport aux arbres vigoureux pour la conversion en biocombustibles solides. La deuxième étude visait à optimiser des procédés de granulation des bois feuillus. L’étude a porté sur l’influence des paramètres du procédé (la température et la force de compression) et des caractéristiques de la matière première (la taille des particules et la teneur en humidité) sur les propriétés physiques et mécaniques des granules de bois. Le procédé de granulation doit être effectué à une température d’environ 100 °C pour minimiser la force de friction dans le granulateur et à une teneur en humidité d’environ 11,2% pour maximiser la masse volumique et la résistance mécanique des granules produites. Cette étude a également confirmé que les arbres de faible qualité sont plus appropriés pour la fabrication de granules de bois que les arbres vigoureux. La troisième étude visait l’élaboration de granules de haute qualité. L’eau chaude à température élevée a été utilisée pour modifier les propriétés de la matière première avant granulation. Les caractéristiques de granulation du matériau traité ont été significativement améliorées. Les granules produites ont montré des propriétés améliorées incluant une plus faible teneur en cendres, une plus haute densité énergétique, une meilleure résistance à l’eau, et une meilleure résistance mécanique. Les résultats obtenus de toutes ces études ont démontré la nécessité de bien connaître les fondements de la granulation des bois feuillus et les solutions pratiques pour l’utilisation d’arbres feuillus de faible qualité, le premier peut être applicable pour le développement de procédés de granulation et le dernier peut contribuer à long terme à la restauration des forêts feuillues dégradées en termes de santé des forêts et de leur valeur.

Francisco Pizarro' s banner of arms: an analytical work contributing to latin America's history

The study of textiles is an open area of scientific research, which for its variety of material components and physical chemical diversity of conditions, makes a field of interest for scientific studies in the cultural heritage field. Archaeological/historical textiles offer the possibility to carry out studies on organic materials such as fibers, adhesion elements, dyes, paper, etc., as well as on inorganic compounds for instance metals, alloys, precious stones and other added ornamentation. That variety of composition, allow to use a combination of analytical techniques to solve the questions coming from the object in an archaeometric research. One kind of textile object that provides a valuable cultural information because of its linguistic representation employed by its carrier societies, are the flags/banners/emblems, objects made with a nonverbal communication purpose. As long as depending on the use and/or purpose of each object, varies both the materials/techniques used in its production and its iconography (style, color, emblem, shape), its study gives the possibility to extract information through their materials and manufacturing techniques about a temporal-spatial frame, a particular event or a specific character. The flags/banners have been used since the eleventh century as representative objects of power, hierarchy, social or military organization, or as communicative media. The use of these objects has been spread throughout the world, possibly due to its easy interpretation and/or appropriation by different societies, making it part of their own culture. The flags as symbols of territorial control, using emblems that represent a family, order or army, were introduced to the New World (America) with the arrival of the European conquerors at the end of the fifteenth century. Flags/banners representing the Royal dominion over conquered territories, the Catholic Church and conquistadors’ armies were the first to arrive. One of those flags that have endured over time, that have an invaluable cultural meaning for both American and Iberian societies, is the so-called Francisco Pizarro’s Banner of Arms. It is a textile object with metal threads decoration over a Royal emblem. According to historical sources, this object was used by Francisco Pizarro in 1532 on the conquest process of Peru, after received the permission by King Charles V to on behalf of him, to conquer the lands of the New World today known as Peru. After Pizarro’s control of the Inca territory, it is believed that Pizarro left his banner on top of the Inca’s Sun’s Temple as symbol of his rule. Centuries later, in the America libertarian campaigns, General Sucre, military at charge of the independence army in Peru, reports have found what he considered the Pizarro’s Banner, sending it to Bogotá as a symbol of victory, being kept since that time until today by the National Museum of Colombia. Due to historical discrepancies in the different movements of the so-called Pizarro’s Banner of Arms, its real meaning has been under discussion and because of the passage of time its physical condition has suffer deterioration. That is because its scientific study is now an interesting case study to respond to both historical and conservation questions of it. Through a collaboration with the National Museum of Colombia, a set of 25 samples of so-called Pizarro’s Banner of Arms were collected, covering the various components and areas from the object of study. These samples were subjected to analytical studies for physical and chemical characterization. Microscopic observation, VSEM-EDS analysis, Raman spectroscopy, chromatographic analysis (HPLC-MS, GCMS) and radiocarbon dating were done. Similarly, was sought through a direct in situ physical inspection to the object and through a research into historical sources, adequate information to solve the object’s problems. Results obtained allowed to identify as silk the textile used in the elaboration of the Banner’s fabric, as well as the use of natural dyes for dyeing the fibers used on the emblem: use of cochineal and brazil wood as a source of red, luteolin plant-based for yellow color, indigotine plant-based for blue, and a mixture of yellow and blue dyes for green were identified. Similarly, the use of animal glue in the manufacturing process and the use of rag paper was evident. The metal threads study from the Banner give a confirmation to a silver core wire gilded with a thin gold sheet, being flattened and entwined with silk threads for their use. Finally, using the radiocarbon results, it was possible to postulate with huge accuracy that the Banner date manufacture was between the XV-XVI century and subject to restoration processes with addition of textiles in modern times. Together with, was evident that the state of degradation of the fabric is due to natural degradation in the silk fibers, having that its color has faded and its mechanical properties decreased, leading to loss of rigidity and disappearance of the physical structure. Similarly, it was clear the original colors of the emblem and highlight problems of detachment of paper due to crystallization of the adhesive. In the same way, was found that the metal threads suffer corrosion by sulfur and detachment of its crystals. Finally, combining the analytical results and the historical sources data found from the so-called Francisco Pizarro’s Banner of Arms, allows to postulate that its manufacture process was done in Europe employing precious materials to obtain a long-life object with a deep message for its viewers. Also, the data obtained helps to support the possible idea that the object was employed by Francisco Pizarro in the Peru conquest process. However, by the symbols present in the object, its elaboration date and materials, this object its clearly unique in its kind, and the most important, by its linguistic message, does not represent to Francisco Pizarro or his army, meanwhile, represents the Spanish crown. Therefore, instead to be labeled as Francisco Pizarro’s Banner of Arms, it should be called the Colonial Royal Banner of Charles V in the New World; RESUMEN: El estudio de textiles es un área abierta de investigación científica, la cual por su variedad de componentes materiales y la diversidad de condiciones físico-químicas presentes en estos objetos, lo hace un campo de interés para estudios científicos en el patrimonio cultural. Los textiles arqueológicos/históricos brindan la posibilidad de realizar estudios en materiales orgánicos como fibras, elementos de adhesión, tinturas, papel, etc., e inorgánicos como metales, aleaciones, piedras preciosas y demás materiales decorativos añadidos. Por su variedad de composición, es posible emplear diversas técnicas analíticas para resolver aquellas preguntas propias del objeto en una investigación arqueométrica. Uno de los objetos textiles que brinda gran información cultural debido a su representación lingüística empleada por las sociedades portadoras, son las banderas/estandartes/emblemas. Donde varía dependiendo de su uso y/o propósito, los materiales empleados en su elaboración, al igual que su iconografía (estilo, color, emblema, forma). El estudio de estos objetos construidos con un propósito de comunicación no verbal, da la posibilidad de extraer información a través de sus materiales y técnicas de elaboración sobre un rango temporal-espacial, un evento determinado en la historia o incluso a un personaje en específico. Las banderas han sido empleadas desde el siglo XI como objetos representativos de poder, jerarquía, organización social o militar, o como medio de comunicación. El uso de estos objetos se ha extendido a lo largo del mundo posiblemente debido a su fácil interpretación y/o apropiación por distintas sociedades, haciéndolo parte de su cultura. Las banderas como símbolos de control territorial, empleando símbolos que representan a una familia, orden o armada fueron introducidas a el Nuevo Mundo (América) con la llegada de los conquistadores europeos al final del siglo XV. Las banderas/estandartes que representaban el dominio Real sobre territorios dominados, la iglesia católica y las banderas de ejércitos y/o conquistadores fueron las primeras en llegar al nuevo mundo. Una de aquellas banderas que ha soportado el paso del tiempo, teniendo un gran valor cultural tanto para las sociedades americanas como para las ibéricas, es el denominado Estandarte de armas de Francisco Pizarro. Siendo un objeto textil con decoración en hilos metálicos sobre un emblema Real. De acuerdo a fuentes históricas, este objeto fue usado por Francisco Pizarro en 1532 en el proceso de conquista del Perú, quien recibe por parte del Rey Carlos V el poder para que, en su nombre, Pizarro pueda conquistar las tierras del nuevo mundo hoy conocidas como Perú. Luego del dominio de Pizarro sobre el territorio Inca, se cree que Pizarro dejó su estandarte en la cima del templo Inca del sol como símbolo de su control. Siglos más tarde, en las campañas libertarias de América, el General Sucre, militar encargado de la armada independentista en Perú, reporta haber encontrado lo que él considera como el estandarte de Pizarro, enviándolo a Bogotá como muestra de victoria, siendo custodiada desde ese momento por el Museo Nacional de Colombia hasta la actualidad. Debido a discrepancias históricas, el verdadero significado del llamado estandarte de Pizarro ha sido objeto de discusión y debido del pasar del tiempo su estado de conservación se ha deteriorado. Dejando de este modo, un caso de estudio interesante para que por medio de estudios científicos al objeto se pueda dar respuesta a preguntas tanto históricas como de conservación del mismo. De este modo, por medio de una colaboración con el Museo Nacional de Colombia, se obtuvo un juego de 25 muestras del llamado Estandarte de armas de Francisco Pizarro, abarcando los diferentes componentes y áreas del objeto de estudio. Dichas muestras fueron sometidas a estudios analíticos para su caracterización físico-química. Análisis de observación al microscopio, análisis VSEM-EDS, espectroscopia Raman, análisis cromatográficos (HPLC-MS, GC-MS) y datación por radiocarbono catorce fueron realizados. Del mismo modo, por medio de una inspección física al objeto in situ y una profunda investigación en fuentes históricas del mismo, se buscó la información adecuada para resolver sus problemáticas. Los resultados obtenidos permitieron identificar como seda el textil empleado en la elaboración del estandarte, así como el uso de colorantes naturales para teñir las fibras en el emblema: uso de cochinilla y palo de Brasil como fuente del color rojo, plantas a base de luteolin para el color amarillo, plantas a base de indigotina para el color azul y mezcla de colorantes amarillos y azules para el color verde fueron identificadas. Del mismo modo se evidencio el uso de adhesivos animales y el uso de papel de trapos en el proceso de manufactura. El estudio de los hilos metálicos, permitió evidenciar el uso de alambres con núcleos de plata con un fino recubrimiento de oro en su exterior, siendo aplanados y entrelazados con hilos de seda para su uso. Finalmente usando la datación por radiocarbono, fue posible conocer con alta precisión que el estandarte fue elaborado entre los siglos XV-XVI y sufrió procesos de restauración con añadidura de textiles en tiempos modernos. Junto a lo anterior, es posible postular que el estado de degradación de la tela es debido a degradación natural en las fibras de seda, teniendo así que su color se ha desvanecido y sus propiedades mecánicas disminuidas, conllevando a perdida de rigidez y desaparición de la estructura. Del mismo modo se pudo conocer los colores originales del emblema y evidenciar problemas de desprendimiento del papel debido a cristalización del adhesivo. Asimismo, se comprobó que los hilos metálicos presentan corrosión por azufre y desprendimiento de sus cristales. Finalmente, combinando los resultados analíticos y la información de fuentes históricas encontradas del llamado Estandarte de armas de Francisco Pizarro, se puede postular que su elaboración fue realizada en Europa, usando materiales preciosos para obtener un objeto de larga vida con un profundo mensaje para sus observadores. También, los datos obtenidos ayudan a dar soporte la posible idea de que este objeto fue usado por Francisco Pizarro en el proceso de conquista del Perú. Sin embargo, debido a los símbolos presentes en el objeto, fecha y materiales de elaboración, este objeto es claramente único en su tipo, y lo más importante, por su mensaje lingüístico, este no representa a Francisco Pizarro o su armada, al contrario, representa a la Corona de España. Por ende, en vez de denominarse como Estandarte de armas de Francisco Pizarro, este objeto debería nombrarse como el Estandarte Real de la Colonia de Carlos V en el Nuevo Mundo.

Design of biobased additives for tuning the properties of biopolymers

This work mainly arises from the necessity to support the rapid introduction of different biobased polymers that the industrial sector has been facing lately. Indeed, while considerable efforts are being made to find environmentally and economically sustainable materials, less attention is paid to their need to be properly compounded to fulfil increasingly rigorous technical and quality requirements. Therefore, there is a strong demand for the development of a novel generation of compatible additives able to improve the properties of biobased polymers while respecting sustainability. With this in mind, a new class of biobased plasticizers is herein proposed. Five different ketal-diesters were selectively synthesized starting from levulinic acid, a promising renewable chemical platform. These molecules were added to poly(vinyl chloride) as model polymer to test their plasticizing effectiveness. Complete morphological, thermal and viscoelastic characterizations showed a clear correlation between the structural features of the ketal-esters and the properties of the material. In addition, no significant leaching was found in both hydrophilic and lipophilic environments. Importantly, the proposed ketal-diesters performed comparably and, in some cases, even better than commercial plasticizers. The same molecules were then added to bacterial poly(3-hydroxybutyrate), a semicrystalline polyester characterized by poor thermal and mechanical properties. Morphology assessments showed no phase separation and the plasticizing effectiveness was confirmed by thermal and viscoelastic analyses, while leaching tests showed low extraction values. Readily usable fractions with controlled structure and tailored properties were obtained from highly heterogeneous industrial grade Kraft lignin. These fractions were then added to poly(vinyl alcohol). Promising preliminary results in terms of compatibility were achieved, with thermograms showing only one glass transition temperature. Finally, a fully biobased glycerol-trilevulinate was successfully synthesized by means of a mild and solvent-free route. Its plasticizing effectiveness was evaluated on poly(vinyl chloride), showing a significant decrease of the glass transition temperature of the material.

Characterization of DNA sequence properties through network and statistical approaches

In this thesis we will see that the DNA sequence is constantly shaped by the interactions with its environment at multiple levels, showing footprints of DNA methylation, of its 3D organization and, in the case of bacteria, of the interaction with the host organisms. In the first chapter, we will see that analyzing the distribution of distances between consecutive dinucleotides of the same type along the sequence, we can detect epigenetic and structural footprints. In particular, we will see that CG distance distribution allows to distinguish among organisms of different biological complexity, depending on how much CG sites are involved in DNA methylation. Moreover, we will see that CG and TA can be described by the same fitting function, suggesting a relationship between the two. We will also provide an interpretation of the observed trend, simulating a positioning process guided by the presence and absence of memory. In the end, we will focus on TA distance distribution, characterizing deviations from the trend predicted by the best fitting function, and identifying specific patterns that might be related to peculiar mechanical properties of the DNA and also to epigenetic and structural processes. In the second chapter, we will see how we can map the 3D structure of the DNA onto its sequence. In particular, we devised a network-based algorithm that produces a genome assembly starting from its 3D configuration, using as inputs Hi-C contact maps. Specifically, we will see how we can identify the different chromosomes and reconstruct their sequences by exploiting the spectral properties of the Laplacian operator of a network. In the third chapter, we will see a novel method for source clustering and source attribution, based on a network approach, that allows to identify host-bacteria interaction starting from the detection of Single-Nucleotide Polymorphisms along the sequence of bacterial genomes.

Development, mechanical characterization and qualification in liquid lead of stainless steels for structural applications in the future fission and fusion nuclear reactors

The research activity carried out in the Brasimone Research Center of ENEA concerns the development and mechanical characterization of steels conceived as structural materials for future fission reactors (Heavy Liquid Metal IV Generation reactors: MYRRHA and ALFRED) and for the future fusion reactor DEMO. Within this framework, two parallel lines of research have been carried out: (i) characterization in liquid lead of steels and weldings for the components of the IV Generation fission reactors (GIV) by means of creep and SSRT (Slow Strain Rate Tensile) tests; (ii) development and screening on mechanical properties of RAFM (Reduced Activation Ferritic Martensitic) steels to be employed as structural materials of the future DEMO fusion reactor. The doctoral work represents therefore a comprehensive report of the research carried out on nuclear materials both from the point of view of the qualification of existing (commercial) materials for their application in the typical environmental conditions of 4th generation fission reactors operating with lead as coolant, and from the point of view of the metallurgical study (with annexed microstructural and mechanical characterization of the selected compositions / Thermo Mechanical Treatment (TMT) options) of new compositional variants to be proposed for the “Breeding Blanket” of the future DEMO Fusion Reactor.

Smart tracking of composite parts: feasibility study and effect on mechanical behaviour

This research proposes a solution for integrating RFID - Radio Frequency Identification technology within a structure based on CFRPs - Carbon Fiber Reinforced Polymers. Therefore, the main objective is to use technology to monitor and track composite components during manufacturing and service life. The study can be divided into two macro-areas. The first portion of the research evaluates the impact of the composite materials used on transmitting the electromagnetic signal to and from the tag. RFID technology communicates through radio frequencies to to track and trace items associated with the tags. In the first instance, a feasibility study was carried out to assess using commercially available tags. Then, after evaluating different solutions, it was decided to incorporate the tags into coupons during production. The second portion of the research is focused on evaluating the impact on the composite material's resistance to tag embedding. It starts with designing tensile test specimens through the FEM model with different housing configurations. Subsequently, the best configuration was tested in the facilities of the In the Faculty of Aerospace Engineering at TU Delft, particularly in the Structure & Materials Laboratory, two tests were conducted: the first one based on ASTM D3039/D3039 - 14 - Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials, the second one dividing the path to failure into failure intervals in a load-unload-reload. Both tests were accompanied by instruments such as DIC, AE, C-Scan and Optical Microscopes. The expected result of the inclusion of RFID tags in composite components is that it brings added value to the parts with which it is associated without affecting too much its mechanical properties. This comes first from the automatic identification of RFID during the production cycle and its useful life. As a result, improvements were made in the design of production facilities.

Development of a novel heat treatment for high performances L-PBF Ti6Al4V alloy: microstructural and mechanical characterization

This work presents the experimental development of a novel heat treatment for a high performance Laser Powder Bed Fusion Ti6Al4V alloy. Additive manufacturing production processes for titanium alloys are particularly of interest in cutting-edge engineering fields, however, high frequency laser induced thermal cycles generate a brittle as built microstructure. For this reason, heat treatments compliant with near net shape components are needed before their homologation and usage. The experimental campaign focused on the development of a multi-step heat treatment leading to a bilamellar microstructure. In fact, according to literature, such a microstructure should be promising in terms of mechanical properties both under static and cyclic loads. The heat treatment development has asked for the preliminary analyses of samples annealed and aged in laboratory, implementing several cycles, differing for what concerns temperatures, times and cooling rates. Such a characterization has been carried out through optical and electron microscopy analyses, image analyses, hardness and tensile tests. As a result, the most suitable thermal cycle has been selected and performed using industrial equipment on mini bending fatigue samples with different surface conditions. The same tests have been performed on a batch of traditionally treated samples, to provide with a comparison. This master thesis activity has finally led to the definition of a heat treatment resulting into a bilamellar microstructure, promising in terms of fatigue performances with respect to the traditionally treated alloy ones. The industrial implementation of such a heat treatment will require further improvements, particularly for what concerns the post annealing water quench, in order to prevent any surface alteration potentially responsible for the fatigue performances drop. Further development of the research may also include push-pull fatigue tests, crack grow propagation and residual stresses analyses.