Improvement of Mechanical Properties and Life Extension of High Reliability Structural Components by Laser Shock Processing

Profiting by the increasing availability of laser sources delivering intensities above 109 W/cm2 with pulse energies in the range of several Joules and pulse widths in the range of nanoseconds, laser shock processing (LSP) is being consolidating as an effective technology for the improvement of surface mechanical and corrosion resistance properties of metals and is being developed as a practical process amenable to production engineering. The main acknowledged advantage of the laser shock processing technique consists on its capability of inducing a relatively deep compression residual stresses field into metallic alloy pieces allowing an improved mechanical behaviour, explicitly, the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Following a short description of the theoretical/computational and experimental methods developed by the authors for the predictive assessment and experimental implementation of LSP treatments, experimental results on the residual stress profiles and associated surface properties modification successfully reached in typical materials (specifically Al and Ti alloys) under different LSP irradiation conditions are presented. In particular, the analysis of the residual stress profiles obtained under different irradiation parameters and the evaluation of the corresponding induced surface properties as roughness and wear resistance are presented.

Towards the development of poly (phenylene sulphide) based nanocomposites with enhanced mechanical, electrical and tribological properties

Novel poly(phenylene sulphide) (PPS) nanocomposites reinforced with an aminated derivative (PPS-NH2) covalently attached to acid-treated single-walled carbon nanotubes (SWCNTs) were prepared via simple melt-blending technique. Their morphology, viscoelastic behaviour, electrical conductivity, mechanical and tribological properties were investigated. Scanning electron microscopy revealed that the grafting process was effective in uniformly dispersing the SWCNTs within the matrix. The storage and loss moduli as a function of frequency increased with the SWCNT content, tending to a plateau in the low-frequency regime. The electrical conductivity of the nanocomposites was considerably enhanced in the range 0.1?0.5 wt% SWCNTs; electrical and rheological percolation thresholds occurred at similar nanotube concentrations. Mechanical tests demonstrated that with only 1.0 wt% SWCNTs the Young's modulus and tensile strength of the matrix improved by 51 and 37%, respectively, without decrement in toughness, ascribed to a very efficient load transfer. A moderate decrease in the friction coefficient and a 75% reduction in wear rate were found for the abovementioned nanotube loading, indicating that PPS-NH2-g-SWCNTs are good tribological additives for thermoplastic polymers. Based on the promising results obtained in this work, it is expected that these nanofillers will be used to develop high-performance thermoplastic/CNT nanocomposites for structural applications.

The role of land and water for trade and food production in Latin America: Environmental trade-offs of agricultural intensification versus extensification

One of humanity’s major challenges of the 21st century will be meeting future food demands on an increasingly resource constrained-planet. Global food production will have to rise by 70 percent between 2000 and 2050 to meet effective demand which poses major challenges to food production systems. Doing so without compromising environmental integrity is an even greater challenge. This study looks at the interdependencies between land and water resources, agricultural production and environmental outcomes in Latin America and the Caribbean (LAC), an area of growing importance in international agricultural markets. Special emphasis is given to the role of LAC’s agriculture for (a) global food security and (b) environmental sustainability. We use the International Model for Policy Analysis of Agricultural Commodities and Trade (IMPACT)—a global dynamic partial equilibrium model of the agricultural sector—to run different future production scenarios, and agricultural trade regimes out to 2050, and assess changes in related environmental indicators. Results indicate that further trade liberalization is crucial for improving food security globally, but that it would also lead to more environmental pressures in some regions across Latin America. Contrasting land expansion versus more intensified agriculture shows that productivity improvements are generally superior to agricultural land expansion, from an economic and environmental point of view. Finally, our analysis shows that there are trade-offs between environmental and food security goals for all agricultural development paths.

Implications of agricultural production, policy and land use changes on water resource assessment

Una gestión más eficiente y equitativa del agua a escala de cuenca no se puede centrar exclusivamente en el recurso hídrico en sí, sino también en otras políticas y disciplinas científicas. Existe un consenso creciente de que, además de la consideración de las cambiantes condiciones climáticas, es necesaria una integración de ámbitos de investigación tales como la agronomía, planificación del territorio y ciencias políticas y económicas a fin de satisfacer de manera sostenible las demandas de agua por parte de la sociedad y del medio natural. La Política Agrícola Común (PAC) es el principal motor de cambio en las tendencias de paisajes rurales y sistemas agrícolas, pero el deterioro del medio ambiente es ahora una de las principales preocupaciones. Uno de los cambios más relevantes se ha producido con la expansión e intensificación del olivar en España, principalmente con nuevas zonas de regadío o la conversión de olivares de secano a sistemas en regadío. Por otra parte, el cambio de las condiciones climáticas podría ejercer un papel importante en las tendencias negativas de las aportaciones a los ríos, pero no queda claro el papel que podrían estar jugando los cambios de uso de suelo y cobertura vegetal sobre las tendencias negativas de caudal observadas. Esta tesis tiene como objetivo mejorar el conocimiento de los efectos de la producción agrícola, política agraria y cambios de uso de suelo y cobertura vegetal sobre las condiciones de calidad del agua, respuesta hidrológica y apropiación del agua por parte de la sociedad. En primer lugar, el estudio determina las tendencias existentes de nitratos y sólidos en suspensión en las aguas superficiales de la cuenca del río Guadalquivir durante el periodo de 1998 a 2009. Desde una perspectiva de política agraria, la investigación trata de evaluar mediante un análisis de datos de panel las principales variables, incluyendo la reforma de la PAC de 2003, que están teniendo una influencia en ambos indicadores de calidad. En segundo lugar, la apropiación del agua y el nivel de contaminación por nitratos debido a la producción del aceite de oliva en España se determinan con una evaluación de la huella hídrica (HH), teniendo en cuenta una variabilidad espacial y temporal a largo de las provincias españolas y entre 1997 y 2008. Por último, la tesis analiza los efectos de los cambios de uso de suelo y cobertura vegetal sobre las tendencias negativas observadas en la zona alta del Turia, cabecera de la cuenca del río Júcar, durante el periodo 1973-2008 mediante una modelización ecohidrológica. En la cuenca del Guadalquivir cerca del 20% de las estaciones de monitoreo muestran tendencias significativas, lineales o cuadráticas, para cada indicador de calidad de agua. La mayoría de las tendencias significativas en nitratos están aumentando, y la mayoría de tendencias cuadráticas muestran un patrón en forma de U. Los modelos de regresión de datos de panel muestran que las variables más importantes que empeoran ambos indicadores de calidad del agua son la intensificación de biomasa y las exportaciones de ambos indicadores de calidad procedentes de aguas arriba. En regiones en las que el abandono agrícola y/o desintensificación han tenido lugar han mejorado las condiciones de calidad del agua. Para los nitratos, el desacoplamiento de las subvenciones a la agricultura y la reducción de la cuantía de las subvenciones a tierras de regadío subyacen en la reducción observada de la concentración de nitratos. Las medidas de modernización de regadíos y el establecimiento de zonas vulnerables a nitratos reducen la concentración en subcuencas que muestran una tendencia creciente de nitratos. Sin embargo, el efecto de las exportaciones de nitratos procedente de aguas arriba, la intensificación de la biomasa y los precios de los cultivos presentan un mayor peso, explicando la tendencia creciente observada de nitratos. Para los sólidos en suspensión, no queda de forma evidente si el proceso de desacoplamiento ha influido negativa o positivamente. Sin embargo, los mayores valores de las ayudas agrarias aún ligadas a la producción, en particular en zonas de regadío, conllevan un aumento de las tasas de erosión. Aunque la cuenca del Guadalquivir ha aumentado la producción agrícola y la eficiencia del uso del agua, el problema de las altas tasas de erosión aún no ha sido mitigado adecuadamente. El estudio de la huella hídrica (HH) revela que en 1 L de aceite de oliva español más del 99,5% de la HH está relacionado con la producción de la aceituna, mientras que menos del 0,5% se debe a otros componentes, es decir, a la botella, tapón y etiqueta. Durante el período estudiado, la HH verde en secano y en regadío representa alrededor del 72% y 12%, respectivamente, del total de la HH. Las HHs azul y gris representan 6% y 10%, respectivamente. La producción de aceitunas se concentra en regiones con una HH menor por unidad de producto. La producción de aceite de oliva ha aumentado su productividad del agua durante 1997-2008, incentivado por los crecientes precios del aceite, como también lo ha hecho la cantidad de exportaciones de agua virtual. De hecho, las mayores zonas productoras presentan una eficiencia alta del uso y de productividad del agua, así como un menor potencial de contaminación por nitratos. Pero en estas zonas se ve a la vez reflejado un aumento de presión sobre los recursos hídricos locales. El aumento de extracciones de agua subterránea relacionadas con las exportaciones de aceite de oliva podría añadir una mayor presión a la ya estresada cuenca del Guadalquivir, mostrando la necesidad de equilibrar las fuerzas del mercado con los recursos locales disponibles. Los cambios de uso de suelo y cobertura vegetal juegan un papel importante en el balance del agua de la cuenca alta del Turia, pero no son el principal motor que sustenta la reducción observada de caudal. El aumento de la temperatura es el principal factor que explica las mayores tasas de evapotranspiración y la reducción de caudales. Sin embargo, los cambios de uso de suelo y el cambio climático han tenido un efecto compensatorio en la respuesta hidrológica. Por un lado, el caudal se ha visto afectado negativamente por el aumento de la temperatura, mientras que los cambios de uso de suelo y cobertura vegetal han compensado positivamente con una reducción de las tasas de evapotranspiración, gracias a los procesos de disminución de la densidad de matorral y de degradación forestal. El estudio proporciona una visión que fortalece la interdisciplinariedad entre la planificación hidrológica y territorial, destacando la necesidad de incluir las implicaciones de los cambios de uso de suelo y cobertura vegetal en futuros planes hidrológicos. Estos hallazgos son valiosos para la gestión de la cuenca del río Turia, y el enfoque empleado es útil para la determinación del peso de los cambios de uso de suelo y cobertura vegetal en la respuesta hidrológica en otras regiones. ABSTRACT Achieving a more efficient and equitable water management at catchment scale does not only rely on the water resource itself, but also on other policies and scientific knowledge. There is a growing consensus that, in addition to consideration of changing climate conditions, integration with research areas such as agronomy, land use planning and economics and political science is required to meet sustainably the societal and environmental water demands. The Common Agricultural Policy (CAP) is a main driver for trends in rural landscapes and agricultural systems, but environmental deterioration is now a principal concern. One of the most relevant changes has occurred with the expansion and intensification of olive orchards in Spain, taking place mainly with new irrigated areas or with the conversion from rainfed to irrigated systems. Moreover, changing climate conditions might exert a major role on water yield trends, but it remains unclear the role that ongoing land use and land cover changes (LULCC) might have on observed river flow trends. This thesis aims to improve the understanding of the effects of agricultural production, policies and LULCC on water quality conditions, hydrological response and human water appropriation. Firstly, the study determines the existing trends for nitrates and suspended solids in the Guadalquivir river basin’s surface waters (south Spain) during the period from 1998 to 2009. From a policy perspective, the research tries to assess with panel data analysis the main drivers, including the 2003 CAP reform, which are having an influence on both water quality indicators. Secondly, water appropriation and nitrate pollution level originating from the production of olive oil in Spain is determined with a water footprint (WF) assessment, considering a spatial temporal variability across the Spanish provinces and from 1997 to 2008 years. Finally, the thesis analyzes the effects of the LULCC on the observed negative trends over the period 1973-2008 in the Upper Turia basin, headwaters of the Júcar river demarcation (east Spain), with ecohydrological modeling. In the Guadalquivir river basin about 20% of monitoring stations show significant trends, linear or quadratic, for each water quality indicator. Most significant trends of nitrates are augmenting than decreasing, and most significant quadratic terms of both indicators exhibit U-shaped patterns. The panel data models show that the most important drivers that are worsening nitrates and suspended solids in the basin are biomass intensification and exports of both water quality indicators from upland regions. In regions that agricultural abandonment and/or de-intensification have taken place the water quality conditions have improved. For nitrates, the decoupling of agricultural subsidies and the reduction of the amount of subsidies to irrigated land underlie the observed reduction of nitrates concentration. Measures of irrigation modernization and establishment of vulnerable zones to nitrates ameliorate the concentration of nitrates in subbasins showing an increasing trend. However, the effect of nitrates load from upland areas, intensification of biomass and crop prices present a greater weight leading to the final increasing trend in this subbasins group, where annual crops dominate. For suspended solids, there is no clear evidence that decoupling process have influenced negatively or positively. Nevertheless, greater values of subsidies still linked to production, particularly in irrigated regions, lead to increasing erosion rates. Although agricultural production has augmented in the basin and water efficiency in the agricultural sector has improved, the issue of high erosion rates has not yet been properly faced. The water footprint (WF) assessment reveals that for 1 L Spanish olive oil more than 99.5% of the WF is related to the olive fruit production, whereas less than 0.5% is due to other components i.e. bottle, cap and label. Over the studied period, the green WF in rainfed and irrigated systems represents about 72% and 12%, respectively, of the total WF. Blue and grey WFs represent 6% and 10%, respectively. The olive production is concentrated in regions with the smallest WF per unit of product. The olive oil production has increased its apparent water productivity from 1997 to 2008 incentivized by growing trade prices, but also did the amount of virtual water exports. In fact, the largest producing areas present high water use efficiency per product and apparent water productivity as well as less nitrates pollution potential, but this enhances the pressure on the available water resources. Increasing groundwater abstractions related to olive oil exports may add further pressure to the already stressed Guadalquivir basin. This shows the need to balance the market forces with the available local resources. Concerning the effects of LULCC on the Upper Turia basin’s streamflow, LULCC play a significant role on the water balance, but it is not the main driver underpinning the observed reduction on Turia's streamflow. Increasing mean temperature is the main factor supporting larger evapotranspiration rates and streamflow reduction. In fact, LULCC and climate change have had an offsetting effect on the streamflow generation during the study period. While streamflow has been negatively affected by increasing temperature, ongoing LULCC have positively compensated with reduced evapotranspiration rates, thanks to mainly shrubland clearing and forest degradation processes. The research provides insight for strengthening the interdisciplinarity between hydrological and spatial planning, highlighting the need to include the implications of LULCC in future hydrological plans. These findings are valuable for the management of the Turia river basin, as well as a useful approach for the determination of the weight of LULCC on the hydrological response in other regions.

Influence of different organoclays on the curing, morphology, and dynamic mechanical properties of an epoxy adhesive

The thermal, mechanical, and adhesive properties of nanoclay-modified adhesives were investigated. Two organically modified montmorillonites: Cloisite 93A (C93A) and Nanomer I.30E (I.30E) were used as reinforcement of an epoxy adhesive. C93A and I.30E are modified with tertiary and primary alkyl ammonium cations, respectively. The aim was to study the influence of the organoclays on the curing, and on the mechanical and adhesive properties of the nanocomposites. A specific goal was to compare their behavior with that of Cloisite30B/epoxy and Cloisite15A/ epoxy nanocomposites that we have previously studied. Both C30B and C15A are modified with quaternary alkyl ammonium cations. Differential scanning calorimetry results showed that the clays accelerate the curing reaction, an effect that is related to the chemical structure of the ammonium cations. The three Cloisite/nanocomposites showed intercalated clay structures,the interlayer distance was independent of the clay content. The I.30E/epoxy nanocomposites presented exfoliated structure due to the catalytic effect of the organic modifier. Clay-epoxy nanocompo-sites showed lower glass transition temperature (Tg) and higher values of storage modulus than neat epoxy thermoset, with no significant differences between exfoliated or intercalated nanocom-posites. The shear strength of aluminum joints using clay/epoxy adhesives was lower than with the neat epoxy adhesive. The wáter aging was less damaging for joints with I.30E/epoxy adhesive.

Water, agriculture and ecosystem services in climate change vulnerable agricultural regions of Spain and Jordan

Irrigated agricultural landscapes generate a valuable set of ecosystem services, which are threatened by water scarcity in many aridand semi‐arid regions of the world. In the Mediterranean region, climate change is expected to decrease water availability through reduced precipitation and more frequent drought spells. At the same time, climate change, demographic and economic development and an agricultural sector highly dependent on irrigation, will raise water demand, increasing experienced water scarcity and affecting the provision of ecosystem services from water resources and agro-ecosystems. In this context, policy makers face the challenge of balancing the provision of different ecosystem services, including agricultural income and production and also water ecosystem protection.

Microstructural and mechanical characterization of tungsten based materials for fusion reactors

El wolframio (W) y sus aleaciones se consideran los mejores candidatos para la construcción del divertor en la nueva generación de reactores de fusión nuclear. Este componente va a recibir las cargas térmicas más elevadas durante el funcionamiento del reactor ya que estará en contacto directo con el plasma. En los últimos años, después de un profundo análisis y siguiendo una estrategia de reducción de costes, la Organización de ITER tomó la decisión de construir el divertor integramente de wolframio desde el principio. Por ello, el wolframio no sólo actuará como material en contacto con el plasma (PFM), sino que también tendría aplicaciones estructurales. El wolframio, debido a sus excelentes propiedades termo-físicas, cumple todos los requerimientos para ser utilizado como PFM, sin embargo, su inherente fragilidad pone en peligro su uso estructural. Por tanto, uno de los principales objetivos de esta tesis es encontrar una aleación de wolframio con menor fragilidad. Durante éste trabajo, se realizó la caracterización microstructural y mecánica de diferentes materiales basados en wolframio. Sin embargo, ésta tarea es un reto debido a la pequeña cantidad de material suministrado, su reducido tamaño de grano y fragilidad. Por ello, para una correcta medida de todas las propiedades físicas y mecánicas se utilizaron diversas técnicas experimentales. Algunas de ellas se emplean habitualmente como la nanoindentación o los ensayos de flexión en tres puntos (TPB). Sin embargo, otras fueron especificamente desarrolladas e implementadas durante el desarrollo de esta tesis como es el caso de la medida real de la tenacidad de fractura en los materiales masivos, o de las medidas in situ de la tenacidad de fractura en las láminas delgadas de wolframio. Diversas composiciones de aleaciones de wolframio masivas (W-1% Y2O3, W-2% V-0.5% Y2O3, W-4% V-0.5% Y2O3, W-2% Ti-1% La2O3 y W-4% Ti-1% La2O3) se han estudiado y comparado con un wolframio puro producido en las mismas condiciones. Estas aleaciones, producidas por ruta pulvimetalúrgica de aleado mecánico (MA) y compactación isostática en caliente (HIP), fueron microstructural y mecánicamente caracterizadas desde 77 hasta 1473 K en aire y en alto vacío. Entre otras propiedades físicas y mecánicas se midieron la dureza, el módulo elástico, la resistencia a flexión y la tenacidad de fractura para todas las aleaciones. Finalmente se analizaron las superficies de fractura después de los ensayos de TPB para relacionar los micromecanismos de fallo con el comportamiento macroscópico a rotura. Los resultados obtenidos mostraron un comportamiento mecánico frágil en casi todo el intervalo de temperaturas y para casi todas las aleaciones sin mejoría de la temperatura de transición dúctil-frágil (DBTT). Con el fin de encontrar un material base wolframio con una DBTT más baja se realizó también un estudio, aún preliminar, de láminas delgadas de wolframio puro y wolframio dopado con 0.005wt.% potasio (K). Éstas láminas fueron fabricadas industrialmente mediante sinterizado y laminación en caliente y en frío y se sometieron posteriormente a un tratamiento térmico de recocido desde 1073 hasta 2673 K. Se ha analizado la evolución de su microestructura y las propiedades mecánicas al aumentar la temperatura de recocido. Los resultados mostraron la estabilización de los granos de wolframio con el incremento de la temperatura de recocido en las láminas delgadas de wolframio dopado con potasio. Sin embargo, es necesario realizar estudios adicionales para entender mejor la microstructura y algunas propiedades mecánicas de estos materiales, como la tenacidad de fractura. Tungsten (W) and tungsten-based alloys are considered to be the best candidate materials for fabricating the divertor in the next-generation nuclear fusion reactors. This component will experience the highest thermal loads during the operation of a reactor since it directly faces the plasma. In recent years, after thorough analysis that followed a strategy of cost reduction, the ITER Organization decided to built a full-tunsgten divertor before the first nuclear campaigns. Therefore, tungsten will be used not only as a plasma-facing material (PFM) but also in structural applications. Tungsten, due to its the excellent thermo-physical properties fulfils the requirements of a PFM, however, its use in structural applications is compromised due to its inherent brittleness. One of the objectives of this phD thesis is therefore, to find a material with improved brittleness behaviour. The microstructural and mechanical characterisation of different tunsgten-based materials was performed. However, this is a challenging task because of the reduced laboratory-scale size of the specimens provided, their _ne microstructure and their brittleness. Consequently, many techniques are required to ensure an accurate measurement of all the mechanical and physical properties. Some of the applied methods have been widely used such as nanoindentation or three-point bending (TPB) tests. However, other methods were specifically developed and implemented during this work such as the measurement of the real fracture toughness of bulk-tunsgten alloys or the in situ fracture toughness measurements of very thin tungsten foils. Bulk-tunsgten materials with different compositions (W-1% Y2O3, W-2% V- 0.5% Y2O3, W-4% V-0.5% Y2O3, W-2% Ti-1% La2O3 and W-4% Ti-1% La2O3) were studied and compared with pure tungsten processed under the same conditions. These alloys, produced by a powder metallurgical route of mechanical alloying (MA) and hot isostatic pressing (HIP), were microstructural and mechanically characterised from 77 to 1473 K in air and under high vacuum conditions. Hardness, elastic modulus, flexural strength and fracture toughness for all of the alloys were measured in addition to other physical and mechanical properties. Finally, the fracture surfaces after the TPB tests were analysed to correlate the micromechanisms of failure with the macroscopic behaviour. The results reveal brittle mechanical behaviour in almost the entire temperature range for the alloys and micromechanisms of failure with no improvement in the ductile-brittle transition temperature (DBTT). To continue the search of a tungsten material with lowered DBTT, a preliminary study of pure tunsgten and 0.005 wt.% potassium (K)-doped tungsten foils was also performed. These foils were industrially produced by sintering and hot and cold rolling. After that, they were annealed from 1073 to 2673 K to analyse the evolution of the microstructural and mechanical properties with increasing annealing temperature. The results revealed the stabilisation of the tungsten grains with increasing annealing temperature in the potassium-doped tungsten foil. However, additional studies need to be performed to gain a better understanding of the microstructure and mechanical properties of these materials such as fracture toughness.

A multi-scale analysis of transforming agricultural markets in the context of globalization: implications for natural resources, food prices and rural poverty in Latin America

Vivimos una época en la que el mundo se transforma aceleradamente. La globalización está siguiendo un curso imparable, la población mundial así como la población urbana siguen creciendo, y en los países emergentes los ingresos promedios aumentan, resultando en un cambio también acelerado de las dietas y hábitos alimentarios. En conjunto esos factores están causando un aumento fundamental de la demanda de alimentos. Junto con la apertura de los mercados agrícolas, estos procesos han provocado un crecimiento del comercio internacional de alimentos durante la última década. Dado que muchos países de América Latina están dotados de abundancia de recursos naturales, estas tendencias han producido un crecimiento rápido de las exportaciones de bienes primarios desde América Latina al resto del mundo. En sólo 30 años la participación en el mercado agrícola de América Latina casi se ha duplicado, desde 10% en 1980 a 18% en 2010. Este aumento del comercio agrícola ha dado lugar a un debate sobre una serie de cuestiones cruciales relacionadas con los impactos del comercio en la seguridad alimentaria mundial, en el medio ambiente o en la reducción de la pobreza rural en países en desarrollo. Esta tesis aplica un marco integrado para analizar varios impactos relacionados con la transformación de los mercados agrícolas y los mercados rurales debidos a la globalización y, en particular, al progresivo aumento del comercio internacional. En concreto, la tesis aborda los siguientes temas: En primer lugar, la producción mundial de alimentos tendrá que aumentar considerablemente para poder satisfacer la demanda de una población mundial de 9000 millones personas en 2050, lo cual plantea grandes desafíos sobre los sistemas de la producción de alimentos. Alcanzar este logro, sin comprometer la integridad del medio ambiente en regiones exportadoras, es un reto aún mayor. En este contexto, la tesis analiza los efectos de la liberalización del comercio mundial, considerando distintas tecnologías de producción agraria, sobre unos indicadores de seguridad alimentaria en diferentes regiones del mundo y sobre distintos indicadores ambientales, teniendo en cuenta escalas diferentes en América Latina y el Caribe. La tesis utiliza el modelo “International Model for Policy Analysis of Agricultural Commodities and Trade (IMPACT)” – un modelo dinámico de equilibrio parcial del sector agrícola a escala global – para modelar la apertura de los mercados agrícolas así como diferentes escenarios de la producción hasta el año 2050. Los resultados del modelo están vinculados a modelos biofísicos para poder evaluar los cambios en la huella hídrica y la calidad del agua, así como para cuantificar los impactos del cambio en el uso del suelo sobre la biodiversidad y los stocks de carbono en 2050. Los resultados indican que la apertura de los mercados agrícolas es muy importante para mejorar la seguridad alimentaria a nivel mundial, sin embargo, produce también presiones ambientales indeseables en algunas regiones de América Latina. Contrastando dos escenarios que consideran distintas modos de producción, la expansión de la tierra agrícola frente a un escenario de la producción más intensiva, se demuestra que las mejoras de productividad son generalmente superiores a la expansión de las tierras agrícolas, desde un punto de vista económico e ambiental. En cambio, los escenarios de intensificación sostenible no sólo hacen posible una mayor producción de alimentos, sino que también generan menos impactos medioambientales que los otros escenarios futuros en todas sus dimensiones: biodiversidad, carbono, emisiones de nitratos y uso del agua. El análisis muestra que hay un “trade-off” entre el objetivo de alcanzar la sostenibilidad ambiental y el objetivo de la seguridad alimentaria, independiente del manejo agrícola en el futuro. En segundo lugar, a la luz de la reciente crisis de los precios de alimentos en los años 2007/08, la tesis analiza los impactos de la apertura de los mercados agrícolas en la transmisión de precios de los alimentos en seis países de América Latina: Argentina, Brasil, Chile, Colombia, México y el Perú. Para identificar las posibles relaciones de cointegración entre los índices de precios al consumidor de alimentos y los índices de precios de agrarios internacionales, sujetos a diferentes grados de apertura de mercados agrícolas en los seis países de América Latina, se utiliza un modelo simple de corrección de error (single equation error correction). Los resultados indican que la integración global de los mercados agrícolas ha dado lugar a diferentes tasas de transmisión de precios en los países investigados. Sobre todo en el corto plazo, las tasas de transmisión dependen del grado de apertura comercial, mientras que en el largo plazo las tasas de transmisión son elevadas, pero en gran medida independientes del régimen de comercio. Por lo tanto, durante un período de shocks de precios mundiales una mayor apertura del comercio trae consigo más inestabilidad de los precios domésticos a corto plazo y la resultante persistencia en el largo plazo. Sin embargo, estos resultados no verifican necesariamente la utilidad de las políticas comerciales, aplicadas frecuentemente por los gobiernos para amortiguar los shocks de precios. Primero, porque existe un riesgo considerable de volatilidad de los precios debido a cambios bruscos de la oferta nacional si se promueve la autosuficiencia en el país; y segundo, la política de proteccionismo asume el riesgo de excluir el país de participar en las cadenas de suministro de alto valor del sector agrícola, y por lo tanto esa política podría obstaculizar el desarrollo económico. Sin embargo, es indispensable establecer políticas efectivas para reducir la vulnerabilidad de los hogares a los aumentos repentinos de precios de alimentos, lo cual requiere una planificación gubernamental precisa con el presupuesto requerido disponible. En tercer lugar, la globalización afecta a la estructura de una economía y, por medios distintos, la distribución de los ingreso en un país. Perú sirve como ejemplo para investigar más profundamente las cuestiones relacionadas con los cambios en la distribución de los ingresos en zonas rurales. Perú, que es un país que está cada vez más integrado en los mercados mundiales, consiguió importantes descensos en la pobreza extrema en sus zonas rurales, pero a la vez adolece de alta incidencia de pobreza moderada y de desigualdad de los ingresos en zonas rural al menos durante el periodo comprendido entre 2004 y 2012. Esta parte de la tesis tiene como objetivo identificar las fuerzas impulsoras detrás de estas dinámicas en el Perú mediante el uso de un modelo de microsimulación basado en modelos de generación de ingresos aplicado a nivel los hogares rurales. Los resultados indican que la fuerza principal detrás de la reducción de la pobreza ha sido el crecimiento económico general de la economía, debido a las condiciones macroeconómicas favorables durante el periodo de estudio. Estos efectos de crecimiento beneficiaron a casi todos los sectores rurales, y dieron lugar a la disminución de la pobreza rural extrema, especialmente entre los agricultores de papas y de maíz. En parte, estos agricultores probablemente se beneficiaron de la apertura de los mercados agrícolas, que es lo que podría haber provocado un aumento de los precios al productor en tiempos de altos precios mundiales de los alimentos. Sin embargo, los resultados también sugieren que para una gran parte de la población más pobre existían barreras de entrada a la hora de poder participar en el empleo asalariado fuera de la agricultura o en la producción de cultivos de alto valor. Esto podría explicarse por la falta de acceso a unos activos importantes: por ejemplo, el nivel de educación de los pobres era apenas mejor en 2012 que en 2004; y también las dotaciones de tierra y de mano de obra, sobre todo de los productores pobres de maíz y patata, disminuyeron entre 2004 y 2012. Esto lleva a la conclusión de que aún hay margen para aplicar políticas para facilitar el acceso a estos activos, que podría contribuir a la erradicación de la pobreza rural. La tesis concluye que el comercio agrícola puede ser un importante medio para abastecer una población mundial creciente y más rica con una cantidad suficiente de calorías. Para evitar adversos efectos ambientales e impactos negativos para los consumidores y de los productores pobres, el enfoque debe centrarse en las mejoras de la productividad agrícola, teniendo en cuenta los límites ambientales y ser socialmente inclusivo. En este sentido, será indispensable seguir desarrollando soluciones tecnológicas que garanticen prácticas de producción agrícola minimizando el uso de recursos naturales. Además, para los pequeños pobres agricultores será fundamental eliminar las barreras de entrada a los mercados de exportación que podría tener efectos indirectos favorables a través de la adopción de nuevas tecnologías alcanzables a través de mercados internacionales. ABSTRACT The world is in a state of rapid transition. Ongoing globalization, population growth, rising living standards and increasing urbanization, accompanied by changing dietary patterns throughout the world, are increasing the demand for food. Together with more open trade regimes, this has triggered growing international agricultural trade during the last decade. For many Latin American countries, which are gifted with relative natural resource abundance, these trends have fueled rapid export growth of primary goods. In just 30 years, the Latin American agricultural market share has almost doubled from 10% in 1980 to 18% in 2010. These market developments have given rise to a debate around a number of crucial issues related to the role of agricultural trade for global food security, for the environment or for poverty reduction in developing countries. This thesis uses an integrated framework to analyze a broad array of possible impacts related to transforming agricultural and rural markets in light of globalization, and in particular of increasing trade activity. Specifically, the following issues are approached: First, global food production will have to rise substantially by the year 2050 to meet effective demand of a nine billion people world population which poses major challenges to food production systems. Doing so without compromising environmental integrity in exporting regions is an even greater challenge. In this context, the thesis explores the effects of future global trade liberalization on food security indicators in different world regions and on a variety of environmental indicators at different scales in Latin America and the Caribbean, in due consideration of different future agricultural production practices. The International Model for Policy Analysis of Agricultural Commodities and Trade (IMPACT) –a global dynamic partial equilibrium model of the agricultural sector developed by the International Food Policy Research Institute (IFPRI)– is applied to run different future production scenarios, and agricultural trade regimes out to 2050. Model results are linked to biophysical models, used to assess changes in water footprints and water quality, as well as impacts on biodiversity and carbon stocks from land use change by 2050. Results indicate that further trade liberalization is crucial for improving food security globally, but that it would also lead to more environmental pressures in some regions across Latin America. Contrasting land expansion versus more intensified agriculture shows that productivity improvements are generally superior to agricultural land expansion, from an economic and environmental point of view. Most promising for achieving food security and environmental goals, in equal measure, is the sustainable intensification scenario. However, the analysis shows that there are trade-offs between environmental and food security goals for all agricultural development paths. Second, in light of the recent food price crisis of 2007/08, the thesis looks at the impacts of increasing agricultural market integration on food price transmission from global to domestic markets in six Latin American countries, namely Argentina, Brazil, Chile, Colombia, Mexico and Peru. To identify possible cointegrating relationships between the domestic food consumer price indices and world food price levels, subject to different degrees of agricultural market integration in the six Latin American countries, a single equation error correction model is used. Results suggest that global agricultural market integration has led to different levels of price path-through in the studied countries. Especially in the short-run, transmission rates depend on the degree of trade openness, while in the long-run transmission rates are high, but largely independent of the country-specific trade regime. Hence, under world price shocks more trade openness brings with it more price instability in the short-term and the resulting persistence in the long-term. However, these findings do not necessarily verify the usefulness of trade policies, often applied by governments to buffer such price shocks. First, because there is a considerable risk of price volatility due to domestic supply shocks if self-sufficiency is promoted. Second, protectionism bears the risk of excluding a country from participating in beneficial high-value agricultural supply chains, thereby hampering economic development. Nevertheless, to reduce households’ vulnerability to sudden and large increases of food prices, effective policies to buffer food price shocks should be put in place, but must be carefully planned with the required budget readily available. Third, globalization affects the structure of an economy and, by different means, the distribution of income in a country. Peru serves as an example to dive deeper into questions related to changes in the income distribution in rural areas. Peru, a country being increasingly integrated into global food markets, experienced large drops in extreme rural poverty, but persistently high rates of moderate rural poverty and rural income inequality between 2004 and 2012. The thesis aims at disentangling the driving forces behind these dynamics by using a microsimulation model based on rural household income generation models. Results provide evidence that the main force behind poverty reduction was overall economic growth of the economy due to generally favorable macroeconomic market conditions. These growth effects benefited almost all rural sectors, and led to declines in extreme rural poverty, especially among potato and maize farmers. In part, these farmers probably benefited from policy changes towards more open trade regimes and the resulting higher producer prices in times of elevated global food price levels. However, the results also suggest that entry barriers existed for the poorer part of the population to participate in well-paid wage-employment outside of agriculture or in high-value crop production. This could be explained by a lack of sufficient access to important rural assets. For example, poor people’s educational attainment was hardly better in 2012 than in 2004. Also land and labor endowments, especially of (poor) maize and potato growers, rather decreased than increased over time. This leads to the conclusion that there is still scope for policy action to facilitate access to these assets, which could contribute to the eradication of rural poverty. The thesis concludes that agricultural trade can be one important means to provide a growing and richer world population with sufficient amounts of calories. To avoid adverse environmental effects and negative impacts for poor food consumers and producers, the focus should lie on agricultural productivity improvements, considering environmental limits and be socially inclusive. In this sense, it will be crucial to further develop technological solutions that guarantee resource-sparing agricultural production practices, and to remove entry barriers for small poor farmers to export markets which might allow for technological spill-over effects from high-value global agricultural supply chains.

Structure and mechanical properties of sodium and calcium caseinate edible active films with carvacrol

Edible active films based on sodium caseinate (SC) and calcium caseinate (CC) plasticized with glycerol (G) at three different concentrations and carvacrol (CRV) as active agent were prepared by solvent casting. Transparent films were obtained and their surfaces were analysed by optical microscopy and scanning electron microscopy (SEM). The influence of the addition of three different plasticizer concentrations was studied by determining tensile properties, while Fourier transformed infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) were used to evaluate the structural and thermal behavior of such films. The addition of glycerol resulted in a reduction in the elastic modulus and tensile strength, while some increase in the elongation at break was observed. In general terms, SC films showed flexibility higher than the corresponding CC counterparts. In addition, the presence of carvacrol caused further improvements in ductile properties suggesting the presence of stronger interactions between the protein matrix and glycerol, as it was also observed in thermal degradation studies. FTIR spectra of all films showed the characteristic bands and peaks corresponding to proteins as well as to primary and secondary alcohols. In summary, the best results regarding mechanical and structural properties for caseinates-based films containing carvacrol were found for the formulations with high glycerol concentrations.

Agricultural and Rural Capital Markets in the EU Candidate Countries: Croatia, the Former Yugoslav Republic of Macedonia and Turkey. Factor Markets Working Paper No. 8, October 2011

This paper analyses agricultural and rural capital factor markets in the three European Union candidate countries: Croatia, the Former Yugoslav Republic (FYR) of Macedonia and Turkey. Aggregate capital market indicators and their dynamics, and factors driving agricultural and rural capital markets are analysed and compared in these countries. In general, agricultural and rural capital markets show similarities with general capital market developments, but agricultural and rural capital markets are facing specific credit constraints related to agricultural assets and rural fixed asset specificities, which constrain their mortgages and collateral use. Credit market imperfections have limited access to the investment credits necessary for the restructuring of small-scale individual farms. Government transfers are used to differing extents in the candidate countries, but generally tend to increase over time. Remittances and donor funds have also played an important role in agricultural and rural economy investments.

Developments in the Agricultural and Rural Capital Market of the Former Yugoslav Republic of Macedonia. Factor Markets Working Paper No. 9, October 2011

The undeveloped rural capital market in the Former Yugoslav Republic of Macedonia is constrained by an urban–rural development gap, with limited capacities for rural development and imperfections in the rural capital market. Among the most striking hindrances are the illegal status of a large share of agricultural buildings and other real estate in rural areas, particularly on the individual family farms that prevail in the country, and the insufficient knowledge and abilities of individual farmers in applying for credit. National, EU and other donor funds are being used to improve knowledge, skills and other human resources, and to address the illegal status of buildings and facilities. In recent years, government support for agricultural, rural and regional development has been introduced to promote good agricultural practices, production and economic activity in rural areas. The elimination of imperfections and improvements to the functioning of the capital market – making access to credit and funds easier, especially for small-scale family farms and for rural development – are seen as measures contributing to agriculture and more balanced rural and regional development.

Will improved access to capital dampen the need for more agricultural land? A CGE analysis of agricultural capital markets and world-wide biofuel policies. Factor Markets Working Paper No. 48, May 2013

This paper analyses the consequences of enhanced biofuel production in regions and countries of the world that have announced plans to implement or expand on biofuel policies. The analysis considers biofuel policies implemented as binding blending targets for transportation fuels. The chosen quantitative modelling approach is two-fold: it combines the analysis of biofuel policies in a multi-sectoral economic model (MAGNET) with systematic variation of the functioning of capital and labour markets. This paper adds to existing research by considering biofuel policies in the EU, the US and various other countries with considerable agricultural production and trade, such as Brazil, India and China. Moreover, the application multi-sectoral modelling system with different assumptions on the mobility of factor markets allows for the observation of changes in economic indicators under different conditions of how factor markets work. Systematic variation of factor mobility indicates that the ‘burden’ of global biofuel policies is not equally distributed across different factors within agricultural production. Agricultural land, as the pre-dominant and sector-specific factor, is, regardless of different degrees of inter-sectoral or intra-sectoral factor mobility, the most important factor limiting the expansion of agricultural production. More capital and higher employment in agriculture will ease the pressure on additional land use – but only partly. To expand agricultural production at global scale requires both land and mobile factors adapted to increase total factor productivity in agriculture in the most efficient way.

Influence of Agricultural Support on Sale Prices of French Farmland: A comparison of different subsidies, accounting for the role of environmental and land regulations. Factor Markets Working Document No. 51, June 2013

This paper investigates the determinants of agricultural land price in several regions in France over the period 1994-2011, using individual plot transaction data, with a particular emphasis on agricultural subsidies and nitrate zoning regulations. It found a positive but relatively small capitalisation effect of the total subsidies per hectare. The data revealed that agricultural subsidies capitalised, at least to some extent, but the magnitude of such a capitalisation depends on the region considered, on the type of subsidy considered, and on the location of the plot in a nitrate surplus zone or not. Only land set-aside premiums significantly capitalise into land price, while single farm payments have a significant positive capitalisation impact only for plots located in a nitrate-surplus zone.

Black laws of Virginia; a summary of the legislative acts of Virginia concerning Negroes from earliest times to the present,

Mode of access: Internet.

The search room catalogues and other finding aids to the records preserved in the Public Record Office, London.

Prepared by a British expert for the use of Dr. Reese and for the guidance of the Virginia Committee: William J. Van Schreeven, Virginia State Library and Francis L. Berkeley, Jr., University of Virginia Library.